PECk-O-MATIC Demand PECk-O-MATIC Demand Bird Feeder KitBird Feeder Kit

PECk-O-MATICPECk-O-MATIC

PECk-O-MATIC Assembly PECk-O-MATIC Assembly InstructionsInstructions

Step 1:Step 1:► Verify all contents of your PECk-O-MATIC Demand Feeder kit. Verify all contents of your PECk-O-MATIC Demand Feeder kit.

It should contain the following: It should contain the following:

One Feeder-Funnel One Trigger-Rod One Catch-Dish

One Catch-Dish-Lock Six Regulator-Disks One Pail-Hanger

Step 2:Step 2:

► Prepare your round pail (not included in this kit) to insert Prepare your round pail (not included in this kit) to insert Feeder-Funnel by drilling or cutting out 4” hole at the bottom Feeder-Funnel by drilling or cutting out 4” hole at the bottom center of your pail. center of your pail.

Pail

Step 3:Step 3:► Review the pictures of the six Regulator-Disks. Review its Review the pictures of the six Regulator-Disks. Review its

openings and recommended feed to use with each Regulator-openings and recommended feed to use with each Regulator-Disk.Disk.

Step4:Step4:

Based on your feed and recommended Regulator-Based on your feed and recommended Regulator-Disk opening, select one Regulator-Disk to use with Disk opening, select one Regulator-Disk to use with your feed. your feed.

Note: If you find our recommended opening too small Note: If you find our recommended opening too small or too large, change to another disk. You can also or too large, change to another disk. You can also make your own disk with your desired opening to use make your own disk with your desired opening to use with PECk-O-MATIC.with PECk-O-MATIC.

Step 5:Step 5:► Securely hang your pail using the Pail-Hanger ( or Pail-Securely hang your pail using the Pail-Hanger ( or Pail-

Holder or Pail-Stand sold separately) so that the bottom of Holder or Pail-Stand sold separately) so that the bottom of the pail is at least 14" above floor level and insert the tube the pail is at least 14" above floor level and insert the tube end of the Feeder-Funnel from inside the pail. When properly end of the Feeder-Funnel from inside the pail. When properly inserted, this Feeder-Funnel should seat tight against the inserted, this Feeder-Funnel should seat tight against the inside wall of the pail with the entire tube end of the funnel inside wall of the pail with the entire tube end of the funnel sticking out through the bottom hole. sticking out through the bottom hole.

Step 6:Step 6:

► Place the Regulator-Disk you selected at the funnel opening. Place the Regulator-Disk you selected at the funnel opening.

Step 7:Step 7:

► Insert the long end of the Trigger-Rod from inside and Insert the long end of the Trigger-Rod from inside and position it at the center of the Regulator-Disk opening. position it at the center of the Regulator-Disk opening.

Step 8:Step 8:

Insert the Catch-Dish from the long end of the Trigger-Rod and Insert the Catch-Dish from the long end of the Trigger-Rod and lock it at desired height using Catch-Dish-Lock by lightly lock it at desired height using Catch-Dish-Lock by lightly pressing together two open ends, pass the Trigger-Rod thru the pressing together two open ends, pass the Trigger-Rod thru the holes, and release.holes, and release.

Step 9:Step 9:

To test your feeder setup, put two cups of feed into the pail To test your feeder setup, put two cups of feed into the pail while keeping the Trigger-Rod somewhat at the center of the while keeping the Trigger-Rod somewhat at the center of the Regulator-Disk. Then wiggle Catch-Dish to make the Trigger-Regulator-Disk. Then wiggle Catch-Dish to make the Trigger-Rod oscillate and see small quantity of feed is dropping. Change Rod oscillate and see small quantity of feed is dropping. Change the Regulator-Disk to increase/decrease quantity of the the Regulator-Disk to increase/decrease quantity of the released feed.released feed.

Step 10:Step 10:

To train your birds, put one cup of feed in the Catch-Dish and To train your birds, put one cup of feed in the Catch-Dish and see how quickly they learn.see how quickly they learn.

Contact USContact US

Address:Address: 6562 Ridings Rd, Syracuse, NY 13206 6562 Ridings Rd, Syracuse, NY 13206 Phone:Phone: 315-362-9772 315-362-9772 Website:Website: www.peckomatic.com www.peckomatic.com Email: Email: sales@peckomatic.comsales@peckomatic.com