Plastic Conveying Valves and Gates

ISO 9001-2000

. . . products made for conveying!

Canada 1-800-263-1942 USA [email protected] • www.lorenz.ca

Valves & GatesIssue No. 3

ISO 9001-2000


Canada 1-800-263-1942 USA [email protected] • www.lorenz.ca- 2 -

Gravity DiverterSeries "B" (Unsealed)

PG 29-30

Gravity DiverterSeries "L" (Sealed Units)

PG 27-28

SlideflexSeries "P" (2-Way & 3-Way)

PG 11-14

Diverter ValvesSeries "D" (3-Way & 4-Way)

PG 7-10

Roller Gate Series "N"

PG 25-26

Slidegates Series "E"

PG 15-22

Aggregate Control Gates Series "C"

PG 37-38

Aggregate Diverters Series "J"

PG 35-36

Diverter ValvesSeries "D" 2-Way “Y” & “ST”

PG 3-6

Gravity VSeries "G"

PG 31-32

Options and Warranty Information - Pg. 39 - 44

Bypass Load Series "F"

PG 33-34

Maintenance GateSeries "A"

PG 23-24

ISO 9001-2000



ISO 9001-2000



261/2 351/4371/2

ISO 9001-2000



2 Way Diverter Valves Series “D”- Y Configuration

Available in Sizes from 2” up to 12”

Inlets & Outlets available in Tube & Pipe Sizesin Stainless Steel, Aluminum & Carbon Steel

Pneumatic actuated 2 way diverter valve for vacuum or low pressure* conveying systems.

*(Dilute phase up to 15 psig max)

Standard Features• Positive blade lock (PBL) between blade & cylinder rod

• Internal magnetic piston, cushioned air cylinder• Active compression seal (ACS) • Polished stainless steel blade

• Light weight aluminum Body construction • Temperature rated for up to 82ºC (180ºF)

• Double acting or single acting spring return solenoid or manual lever valve• NEMA 4 watertight & dust tight electrics

• Wall thicknesses of 16, 14 & 11 gauge, schedule 10, 40 & 80• Fully tested prior to shipping

ISO 9001-2000



2 Way Diverter Valves - Series “D”“Y” Configuration

DV2-Y - Side View

DV2-150 1 1/2 7 1/4 4 1/8 5 5 3/4 14 3/4 2 1/2 30DV2-200 2 7 1/4 4 1/8 5 5 3/4 14 3/4 2 1/2 30DV2-2188 2 3/16 8 4 6 7 3/4 18 3/8 3 1/2 30DV2-2375 2 3/8 10 1/8 5 1/8 6 7 3/4 18 3/8 3 1/2 30 DV2-250 2 1/2 8 4 1/8 6 7 3/4 18 3/8 3 1/2 30DV2-2875 2 7/8 10 5 6 7 3/4 18 3/8 3 1/2 30DV2-300 3 8 5/8 4 1/8 6 7 3/4 18 3/8 3 1/2 30

DV2-350 3 1/2 12 3/4 6 1/8 7 10 1/2 22 3/4 5 30DV2-400 4 10 3/8 4 1/8 7 10 1/2 22 3/4 5 30DV2-450 4 1/2 13 3/4 6 1/8 9 12 3/4 25 3/4 6 30DV2-500 5 12 5/8 5 1/8 9 12 3/4 25 3/4 6 30 DV2-5563 5 9/16 15 1/4 6 1/8 10 14 3/4 30 1/8 7 30DV2-600 6 13 7/8 5 1/8 10 14 3/4 30 1/8 7 30DV2-6625 6 5/8 15 1/2 7 11 21 3/8 40 1/4 10 45 DV2-800 8 19 1/8 9 1/8 12 21 1/2 38 1/2 10 45DV2-8625 8 5/8 19 3/4 8 1/4 14 24 1/2 44 1/4 12 45DV2-1000 10 21 3/4 9 5/8 15 3/4 28 1/4 49 1/2 14 45DV2-1075 10 3/4 22 3/4 9 3/4 15 3/4 28 1/4 49 1/2 14 45DV2-1200 12 24 1/4 9 3/4 16 29 49 1/2 14 45

Dry, filtered & lubricated actuating air @ 80 PSIG minimum, 200 PSIG maximum recommended

Model number Size A B C E F G H R

DV2-Y - Top View

E

F GH

B

C

R

A

H

Options • Position switches 110 volt AC & 24 volt DC • Manual hand wheel operation

• Proximity switches • Special seal configurations

• Oversized air cylinders • Solenoids 110 volt AC or 24 volt DC

• Valve body sealed for sir purging • NEMA 7-9 hazardous locations

• Inlets/outlets - straight or flanged ends • High temperature modifications(Class I, Groups B, C&D, Class II, Groups E, F, & G)

38

ISO 9001-2000



ISO 9001-2000



ISO 9001-2000



ISO 9001-2000



ISO 9001-2000



ISO 9001-2000



ISO 9001-2000



ISO 9001-2000



E

ISO 9001-2000



Series “E” - Slide Gates

“LSP” - LightweightStud Pattern

Stud bolt flanged tubeconnection for light duty applications.

“TPS” - Tube & Pipe Stubs

Tube & pipe stubs for compression couplings.

Pneumatic actuated slide gate for vacuum or low pressure* conveying systems


• Internal magnetic piston, cushioned air cylinder• Active compression seal (ACS)• Polished stainless steel blade

• Light weight aluminum body construction• Temperature rated for up to 82O C (180OF)

• Double acting or single acting spring return solenoid or Manual lever valve

• NEMA 4 watertight & dust tight electrics• Wall thickness of 16, 14 & 11 gauge, schedule 10, 40 & 80

• Fully tested prior to shipping

* Dilute phase up to 15 psig max)

ISO 9001-2000



Series “E” - Slide Gates“LSP” - LightweightStud Pattern“TPS” - Tube & Pipe Stubs

DO2 8/74 8/72 5 8/54 4/131 5 4 8/73 CN81-61/5 8/7

DO61/32 8/74 8/72 6 5 8/151 5 4 8/73 CN81-61/5 8/7

DO8/32 8/74 8/72 6 5 8/151 5 4 8/73 CN81-61/5 8/7

DO2/12 8/74 8/72 6 4/35 61 5 4 8/73 CN81-61/5 8/7

DO8/72 8/74 8/72 6 4/35 61 5 4 8/73 CN81-61/5 8/7

DO3 8/74 8/72 6 8/76 61 5 4 5 CN81-61/5 8/7

DO2/13 8/74 8/72 7 8/77 02 5 4 5 CN81-61/5 8/7

DO4 8/74 8/72 7 8/77 02 5 6 2/15 CN81-61/5 8/7

DO2/14 8/74 8/72 9 2/18 2/122 5 6 2/15 CN81-61/5 8/7

DO5 8/74 8/72 9 8/101 42 5 8 2/16 CN81-61/5 8/7

DO61/95 8/74 8/72 01 8/101 42 5 8 2/16 CN81-61/5 8/7

DO6 8/74 8/72 01 8/111 2/152 5 8 2/17 CN81-61/5 8/7

DO8/56 8/74 8/72 11 21 4/362 5 8 2/17 CN81-61/5 8/7

DO8 8/74 8/72 21 8/141 2/103 5 8 2/19 CN81-61/5 8/7

DO01 8/75 8/72 41 8/371 8/553 7 8 2/111 CN81-61/5 8/7

DO4/301 8/75 8/72 41 8/371 8/553 7 21 2/111 CN81-61/5 8/7

DO21 8/75 8/72 61 8/702 4/114 7 21 61/3131 CN81-61/5 8/7

DO4/321 8/75 8/72 61 8/702 4/114 7 21 61/3131 CN81-61/5 8/7

DO41 8/75 3 81 8/532 64 7 21 61 CN81-61/5 8/7

DO2/11

DO2 8/74 8/72 5 8/54 4/131 5 4 8/73 CN81-61/5 8/7

DO61/32 8/74 8/72 6 5 8/151 5 4 8/73 CN81-61/5 8/7

DO8/32 8/74 8/72 6 5 8/151 5 4 8/73 CN81-61/5 8/7

DO2/12 8/74 8/72 6 4/35 61 5 4 8/73 CN81-61/5 8/7

DO8/72 8/74 8/72 6 4/35 61 5 4 8/73 CN81-61/5 8/7

DO3 8/74 8/72 6 8/76 61 5 4 5 CN81-61/5 8/7

DO2/13 8/74 8/72 7 8/77 02 5 4 5 CN81-61/5 8/7

DO4 8/74 8/72 7 8/77 02 5 6 2/15 CN81-61/5 8/7

DO2/14 8/74 8/72 9 2/18 2/122 5 6 2/15 CN81-61/5 8/7

DO5 8/74 8/72 9 8/101 42 5 8 2/16 CN81-61/5 8/7

DO61/95 8/74 8/72 01 8/101 42 5 8 2/16 CN81-61/5 8/7

DO6 8/74 8/72 01 8/111 2/152 5 8 2/17 CN81-61/5 8/7

DO8/56 8/74 8/72 11 21 4/362 5 8 2/17 CN81-61/5 8/7

DO8 8/74 8/72 21 8/141 2/103 5 8 2/19 CN81-61/5 8/7

DO01 8/75 8/72 41 8/371 8/553 7 8 2/111 CN81-61/5 8/7

DO4/301 8/75 8/72 41 8/371 8/553 7 21 2/111 CN81-61/5 8/7

DO21 8/75 8/72 61 8/702 4/114 7 21 61/3131 CN81-61/5 8/7

DO4/321 8/75 8/72 61 8/702 4/114 7 21 61/3131 CN81-61/5 8/7

DO41 8/75 3 81 8/532 64 7 21 61 CN81-61/5 8/7

All dimensions in inches

DO2/11 8/74 4 5 8/54 4/131 5

DO2 8/74 4 5 8/54 4/131 5

DO61/32 8/74 4 6 5 8/151 5

DO8/32 8/74 4 6 5 8/151 5

DO2/12 8/74 4 6 4/35 61 5

DO8/72 8/74 4 6 4/35 61 5

DO3 8/74 4 6 8/75 61 5

DO2/13 8/74 6 7 8/77 02 5

DO4 8/74 4 7 8/77 02 5

DO2/14 8/74 6 9 2/18 2/122 5

DO5 8/74 5 9 8/101 42 5

DO61/95 8/74 5 01 8/101 42 5

DO6 8/74 5 01 8/111 2/152 5

DO8/56 8/74 7 11 21 4/362 5

DO8 8/74 9 21 8/141 2/103 5

DO8/58 8/74 9 31 2/141 4/303 5

DO01 8/75 9 41 8/371 8/553 7

DO4/301 8/75 9 41 8/371 8/553 7

DO21 8/75 9 61 8/702 4/114 7

DO4/321 8/75 9 61 8/702 4/114 7

DO41 8/75 9 81 8/532 64 7

5

9

5 7/8

9

1010

ISO 9001-2000



ISO 9001-2000



Lorenz

9

10

2 1/2

2 1/2

12

ISO 9001-2000



Series "U" Slidegate(Sized for ID of 1/8” Wall Tube)

Standard Features

• Positive Blade Lock (PBL) between blade & cylinder rod

• Internal magnetic piston, cushioned air cylinder

• Stainless steel 5/16” – 18 nc studs for mounting

• Active Compression Seals (ACS)

• 1/4” polyethylene gaskets included

• Polished stainless steel blade

• Light weight aluminum body construction

• Temperature rated for up to 82OC (180OF)

Pneumatic activated slidegate for vacuum or low pressure systems.(Dilute phase up to 15 psig max)

Unlined orifice has smaller footprint and is ideal for plastic

pellets and grains.

ISO 9001-2000



Series "U" Slidegate

¼” Polyethelene Gasket

OptionsTube stubsHi-temp kitsSolenoids

Position SwitchesPre-wired terminal box

Flange adapters & transition

ISO 9001-2000



Standard Features• Stainless steel material contact points

• Dust tight seals• Lightweight aluminum frame, corrosion resistant

• Rated for 82oC (180oF)

Push-Pull Slide GateSeries “E”

For Gravity Flow Applications and Vacuum

Available in sizes 2” to 12”

- 21 -

ISO 9001-2000



Options• 316 stainless material contact

• High temperature service

- 22 -

Push Pull Slide Gate

ISO 9001-2000



Standard Features• Hand crank or hand wheel actuation• Polymer liner • Clear covers standard• 304 stainless steel contact points &

polished stainless steel blade• Narrow profile, lightweight aluminum frame

• Constant pressure woven Teflon seals• Fully lined nylon interior

• Standard gate rated for 110o C (230o F)• Fully tested prior to shipping

Maintenance Gate - Series “A”Handcrank actuated maintenance gate for vacuum or low pressure* systems.*(Dilute Phase up to 15psig max)

Aluminum construction

standard.Available in sizes from 6” up to 16”

Round

Square

ISO 9001-2000



Maintenance Gate - Series “A”

Maintenance Gate Valve - Square Orifice

Maintenance Gate Valve - Round Orifice

• Air cylinders, hand wheel, electric or chain wheel actuation• Solenoids - single or double acting 110 volt AC & 24 volt DC NEMA 4

(available NEMA 7 class 1, Groups B, C & D, class II Groups E, F, & G)

• Stainless steel or carbon steel construction • Clear covers

Options

ISO 9001-2000




• Internal magnetic piston, cushioned air cylinder• Polished stainless steel blade

• Narrow profile, light weight aluminum frame• Adjustable nylon cam rollers for dust tight seal on blade

• Constant pressure nylon seals on blade• Fully lined polymer interior

• Regular flange patterns or CEMA flanges to match screw conveyors• Standard gate rated for 82o C (180o F)

• Fully tested prior to shipping

Aluminumconstruction standard.

Available in sizes from 6” up to 30”

Roller Gate - Series “N”Pneumatic Actuated Roller Gate for gravityflow or low pressure applications*.*(no pressure differential, consult factory)

ISO 9001-2000



Options• Solenoids - single or double acting 110 volt AC & 24 volt DC NEMA 4

(available NEMA 7 class 1, groups B, C & D, class II groups E, F, & G)

• Oversized air cylinders • Hand wheel, hand crank, electric or chain wheel actuation

• Position switches mounted on air cylinder NEMA 4, 110 volt AC & 24 volt DC• High temperature modifications available

• Stainless steel• Clear covers

Roller Gate - Series “N”Regular Flange

Regular

CEMA Flange

CEMA

ISO 9001-2000



Gravity Diverters

Standard Features• For dry gravity flow applications providing a seal to the atmosphere

• Sizes from 4” up to 30”• Stainless steel, carbon steel & aluminum construction

• All valves come with square inlets and outlets standard • Blade pocket protects leading edge of blade from wear and

directs flow of material away• Suitable for up to 82o C (180o F)

• Replaceable active compression shaft seal and urethane blade seal• Valves come standard with double acting, magnetic piston air cylinder

Sealed UnitsSeries "L"

3-Way Sealed Gravity Diverters


Options• Square to round transitions available

• Removable door for cleaning & seal replacement (knobs optional) • Solenoids - double or single acting

• High temperature modifications available

ISO 9001-2000




45o

SIZE B C D E F G WT(apprx)

4 9 7 1/2 16 11 7/8 51/4 53/8 40 (10ga)

6 10 1/4 9 18 13 7/8 5 3/4 6 3/8 50 (10 ga)

8 11 1/2 10 1/2 19 1/2 15 3/4 6 1/4 71/2 65 (10 ga)

10 13 12 24 5/8 18 7 8 1/2 80 (10 ga)

12 14 1/4 13 26 1/2 20 7 3/4 9 1/4 95 (10 ga)

14 15 3/4 14 1/2 27 1/4 22 1/8 8 1/2 10 1/4 120 (7 ga)

16 17 16 30 1/8 24 9 11 3/8 140 (7 ga)

18 19 19 34 1/2 26 3/4 9 1/2 13 1/2 160 (7 ga)

20 21 1/2 22 39 30 10 1/2 15 1/2 185 (7 ga)

22 23 24 42 3/8 32 1/4 11 17 210 (7 ga)

24 25 1/2 29 49 1/2 35 3/4 11 20 1/2 360 (1/4")

26 27 31 53 38 11 1/2 22 430 (1/4")

28 29 33 56 3/8 40 5/8 12 1/2 23 3/8 500 (1/4")

30 301/2 35 593/4 427/8 13 243/4 570 (1/4")

45o

SIZE B C D E F G WT(apprx)

4 15 1/4 8 15 1/4 4 1/2 11 3/8 12 3/8 50 (10 ga)

6 18 9 3/4 19 4 3/4 13 3/4 14 1/2 65 (10 ga)

8 21 11 1/2 22 5/8 5 1/4 16 1/4 16 3/4 75 (10 ga)

10 23 13 25 7/8 5 18 3/8 18 110 (10 ga)

12 26 14 3/4 29 3/8 5 1/2 20 7/8 20 3/8 130 (10 ga)

14 29 16 1/2 32 3/4 6 1/8 23 3/8 22 5/8 180 (7 ga)

16 32 1/2 18 1/2 36 1/8 7 26 1/8 25 3/8 220 (7 ga)

18 36 20 1/2 40 1/2 7 3/4 29 28 1/4 260 (7 ga)

20 39 1/2 22 1/2 44 3/4 8 1/2 31 7/8 31 300 (7 ga)

22 43 24 1/2 48 1/2 9 3/8 34 5/8 33 7/8 350 (7 ga)

24 46 1/2 27 53 3/8 9 1/4 38 1/8 36 1/4 500 (1/4")

26 50 29 57 1/8 10 41 39 800 (1/4")

28 53 31 60 7/8 10 7/8 43 7/8 41 3/8 900 (1/4")

30 54 31 7/8 62 7/8 9 7/8 45 41 5/8 1100 (1/4")

GE

F

B

C

D

30O

A B C D E F G H WT. Material

4 18 ¼ 9 24 7/8 17 5/8 18 16 ¼ 12 100 10 ga

6 20 ½ 10 ½ 29 5/8 20 5/8 21 18 13 3/4 150 10 ga

8 24 12 ½ 35 3/8 24 5/8 25 21 15 3/4 200 10 ga

10 25 ½ 14 40 1/8 27 3/4 28 22 17 3/4 250 10 ga

12 28 ½ 16 46 31 3/4 32 24 ½ 19 3/4 300 10 ga

14 31 ½ 18 51 5/8 35 3/4 36 27 24 450 3/16

16 35 20 57 3/8 39 5/8 40 30 26 525 3/16

18 38 ½ 22 65 3/4 43 5/8 44 33 28 600 3/16

45O

A B C D E F G H WT. Material

4 15 ¼ 8 21 5/8 4 ½ 11 3/8 12 3/8 12 100 10 ga

6 18 9 3/4 26 5/8 4 3/4 13 3/4 14½ 13 3/4 150 10 ga

8 21 11 ½ 31 ½ 5 ¼ 16 ¼ 16 3/4 15 3/4 200 10 ga

10 23 13 35 7/8 5 18 3/8 18 17 3/4 250 10 ga

12 26 14 3/4 40 7/8 5 ½ 20 7/8 20 3/8 19 3/4 300 10 ga

14 29 16 ½ 45 3/4 6 1/8 23 3/8 22 5/8 24 450 3/16

16 32 ½ 18 ½ 51 1/8 7 26 1/8 25 3/8 26 525 3/16

18 36 20 ½ 58 7 3/4 29 28 ¼ 28 600 3/16

Dimensions

GE

F

B

C

D

HH

B

C

D

C

E

F

G

H

G

D

CC

EF

B

H

G E

F

D

C

H

B

Dimensions


45O45O( 30o leg optional)

Size Size

ISO 9001-2000



Unsealed Gravity Diverters

Series "B"

Standard Features

2 Way & 3 Way

- 29 -

ISO 9001-2000



Multi Port Diverter Systems

Standard Features• Custom built automatic material transfer stations

• From multiple sources to multiple stations• Eliminates hose stations, operator error & spills • Single piece units or separate cells

• Combine 2,3, & 4 way diverter valves and slide gates• Can be manufactured as 1 unit or multiple units closer to source

• Can be hard piped or hoses used for fl exibility and ease of maintenance• Add purge valves for cleaning lines • Single piece units or separate cells • PLC Controlled Cabinets

Line Controllers

Features & Benefi ts• Allows full control of conveying lines.

Using 2 slidegates and separate controls.• Either valve can open or close or both open or close.

• Variety of confi gurations 45 & 60 degree branch laterals• Y smooth branches • ST smooth branches• Aluminium, stainless steel & carbon steel.

• All sizes and confi gurations may not be available.• Consult factory for details.

ISO 9001-2000



Standard Features• Stainless steel material contact points • Dust tight seals

• Lightweight aluminum frame, corrosion resistant• Choice of stainless, aluminum and carbon inlets and outlets

• 60o configuration standard -45o optional• No internal ledges for product to collect• Rated for 82oC (180oF)

Gravity V DiverterSeries “G”

For Gravity Flow Applications

ISO 9001-2000



Gravity V DiverterFor Gravity Flow Applications

Options• 316 stainless material contact

• High temperature service• Hand wheel or crank, electric actuation

• Single and double solenoids• Variable and infinite positioning controls

ISO 9001-2000



Standard Features• Stainless steel material contact points

• Lightweight aluminum frame, corrosion resistant• Positive blade lock (PBL) between blade and cylinder rod

• Active compression seals (ACS)• Internal magnetic piston cushioned air cylinder

• Stacking design for multiple conveying lines• Rated for 82oC (180oF)

Pneumatic actuated diverter valve for vacuum or

low pressure* conveying systems.

Fills hoppers via cyclonic separation in the inlet load tube and

exhausting air in the outlet tube.Valves can be stacked on top of each other

allowing multiple sources to multiple hoppers.

Available in sizes 2” to 8”.

By Pass Load DiverterSeries “F”

For Pneumatic Conveying Systems Applications

ISO 9001-2000



By Pass Load Diverter

Options• 316 stainless material contact points

• High temperature service

ISO 9001-2000



2-Way Aggregate Diverter ValveSeries “J”

Standard Features• Sizes from 6” to 24”

• Heavy duty carbon steel construction• Standard magnetic piston cushioned air cylinder

• 45 degree off leg standard• Access door for maintenance and inspection of valve

AG Diverter designed for gravity flow applications of dry aggregate materials.

Options• 30 degree off leg

• Hand wheel/lever or chain wheel actuators• Square to round transitions • High temperature kits

• Dead pocket detector • Interior polymer liners• Pocketed liner • Solenoids & position switches

ISO 9001-2000



30o Off Leg (Optional)

45o Off Leg (Standard)

ISO 9001-2000



Aggregate Control GateSeries “C”

• 6” - 30” sizes• Heavy Duty Carbon Steel Construction

• Standard Hand Wheel Actuated

Features & Benefits

Gate for controlling dry, gravity flow aggregates.

• AR Plate Blade• Square to round transitions • Hi Temp Kits• Internal magnetic cushioned air cylinder

• Solenoids & position switches • Hand lever, chain wheel

Options

ISO 9001-2000



ISO 9001-2000



OptionsValves & Gates

Pre-wired Terminal Boxes

• NEMA 4 water/dust tight enclosure end mounted on air cylinder.• Comes complete with all wires, fittings and connections, simply bring power and air supply to box and unit is ready.

ISO 9001-2000



OptionsValves & Gates

Air-Purged Body c/w Gauge & Regulator

• Body of valve is sealed & pressurized to prevent passing of product into valve cavity• User sets to 2psi greater than conveying pressure

Special Service Inlets

A special service inlet directs the flow of material towards the centre of the valve, preventing shearing and packing of material. Recommended when closing on a column of material, gravity flow and abrasive materials.

ISO 9001-2000



Valve Electrical Controls

• Comes with metal panel enclosure (NEMA 4,X) • Option NEMA 7-9 • On-Off switch standard • Uses relays 110 volt AC or 24 volt DC

• Pre-wired terminal box required if mounted more than 9 ft (3 m) from valve (specify distance)

Details

2 Push Button2 Position Push Button (open and closed)

For simple open and closed operations

• Comes with metal enclosure (NEMA 4,X) with 3 lighted push buttons

• Option NEMA 7-9 • On-Off switch standard• Uses programmable relay 110 volt AC or 24 volt DC

• Operates from closed to open then centre or open to closed then centre• Variable position is manually adjustable by moving centre position switch

• Pre-wired terminal box required if mounted more than 9 ft (3 m) from valve (specify distance)

Details

Variable Centre Position (dribble feed)Operates from closed to open then centre or open to closed then centre.Variable position is manually adjustable by moving centre position switch.

Available on slide gates, roller gates

Moveable variable position switch

ISO 9001-2000



Infinite Position Controls

• Infinite position controls allow for gate to be open to a specified opening size*

• 110 volt AC or 24 volt DC, NEMA 4 enclosure operates by PLC • On & off selector switch

• Rotary position control switch on panel controls opening of valve (can be wired directly to a PLC)

Details

Available on slide gates, roller gates

*Does not control amount of flow just provides opening.

ISO 9001-2000



Application Chart

- 43 -

Valve Type Series Sizes Pressure Gravity Vacuum Mounting Actuator

15 psig max. Note: “Hand” includes crank & wheel

Diverter Valves - 2 Way - ST or Y configuration D 1.5”-12” • • horiz/vert Air, Hand, Electric

3 Way D 2”-8” • • horiz/vert Air, Hand, Electric

4 Way D 2”-8” • • horiz/vert Air, Hand, Electric

Slide Gate - TPS-LSP-BBH-SB-BTV E 1.5”-14” • • • horiz/vert Air, Hand, Electric

Push-Pull Slide Gate E 2”-12” • horiz/vert Hand

Slide Gate Unlined Orifice U 1.5”-12” • • • horiz/vert Air, Hand, Electric

Slide Flex 2 Way & 3 Way p 2”-8” • • horiz/vert Air, Hand, Electric

Roller Gate N 6”-30” • horiz Air, Hand, Electric

Maintenance Gate A 6”-16” • • • horiz Air, Hand

By Pass Load Diverter F 2”-8” • • horiz Air, Hand, Electric

Gravity V Diverter G 5” - 24” • horiz Air, Hand, Electric

Gravity Diverter Sealed 2 Way L 4”-30” • horiz Air, Hand Lever

3 Way L 4”-18” • horiz Air, Hand Lever

Gravity Diverter Unsealed 2 Way & 3 Way B 3”-14” • horiz Air, Hand Lever

Aggregate Control Gate C 6”-30” • horiz Air, Hand, Electric

Aggregate Diverter Valve 2 Way J 6”-18” • horiz Air, Hand, Electric

This chart is for reference only.Please contact a customer service representative for more details.

ISO 9001-2000


Canada 1-800-263-1942 USA [email protected] • www.lorenz.caCanada • 800-263-1942 [email protected] www.lorenz.ca USA • 800-263-7782Tel • 905-372-2240 P.O. Box 20 • Cobourg • Ontario • Canada • K9A 4K2 Fax • 877-372-4456

16863 Printed in Canada May 2007.

All products manufactured to ISO 9001-2000 standard.

WarrantyLorenz has a limited warranty on

air cylinders and solenoids for 24 months

Any modifications to any valve other than recommended maintenance voids the warranty.

Lorenz warrants to the original buyer only that all products or parts sold by Lorenz shall be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, when used according to Lorenz recommended usages. This warranty is strictly limited to repair, replacement of defective parts, provided those products are returned to Lorenz prepaid. Labour and materials for any downtime/repair/replacement is not covered. This warranty shall be considered void if such products are misused, improperly installed, improperly stored, operated beyond rate limitations, damaged, neglected, altered/changed/repaired or modified by anyone other than Lorenz or designate. Lorenz assumes no responsibility for any emissions from our valves.

All special order products or material are not returnable. No liability is assumed for consequential damages or for any labour or other expense incurred by reason of sale or use of our products, singularly or in combination with other products. To the best of our ability products will be delivered at specific times but no liability is assumed for failure to deliver because of delays or defaults occasioned directly or indirectly by fire, flood, act of God, labour trouble or shortage or any cause unavoidable beyond our reasonable contract.

Goods remain the property of the seller until payment is received in full and purchaser acknowledges in full that this is a security agreement and a document to this effect may be registered according to the local and applicable legislation or there shall be a charge for the full purchase price on the goods. All special order products or material are not returnable.

Date post:	06-Jun-2015
Category:	Documents
Upload:	tony-cresicbene
View:	415 times
Download:	2 times

Plastic Conveying Valves and Gates

Documents