SS piping

Orig. 12/03/2008 Original Issue (preliminary)

Rev. Date/Issued NotesDate/Checked Date/Approved

PIPING STANDARDS

STAINLESS STEEL PIPES

SE.001.B SE.0008 STANDARD Revision No 0

Chapter ENGINEERING

Application Date 16/11/1998

Designation Valve specifications, PS

Classement Standard SE

Page 1/3

0 16/11/1998 DELEASE B. BACUEZ L. PASCAL C. VANNUFFELEN

Rev. No DATE MODIFICATION WRITTEN BY: CHECKED BY: APPROVED BY:

Se0008.doc - OteroJ/oj 10/06/2011

Classification Standard SE

� PURPOSE

Recommendations for valve specifications.

� APPLICATION FIELD

This instruction applies for stock preparation lines, approach systems and white water systems of paper mills.

� SPECIFICATIONS

Diameters Code Application Specifications Suppliers

Isolating Type: Straight gate Tecofi Stock at 1% Opening: Through bore Vade consistency Body: Cast iron Orbinox And over Gate: Stainless steel or equal Stemm: Stainless steel VG Seal: Metal/metal Outside finish: Epoxy paint connection: Between flanges PN 10/16 Actuator: Handwheel Dimensions: ISO standards

Control Type: Straight gate Tecofi Stock at 1% Opening: Vee port Vade consistency Body: Cast iron Orbinox

And over Gate: Stainless steel or equal Stemm: Stainless steel

VGT Seal: metal/metal Outside finish: Epoxy paint connection: Between flanges PN 10/16

Actuator: Handwheel

ND 65 Dimensions: ISO standards

and over Fine control Type: Slanted gate Tecofi Stock at 1% Opening: Reduced / square Vade consistency Body: Cast iron Orbinox And over Gate: Stainless steel or equal

VGS Stemm: Stainless steel Seal: metal/metal Outside finish: Epoxy paint connection: Flanges PN 10/16 Actuator: Handwheel Dimensions: ISO standards

Multiway Type: 3 way De zurik Stock at 1% Opening: Reduced / square Papiros consistency Body: Cast iron or equal And over Plug : Stainless steel VGY Stemm: Stainless steel Seal: metal/metal Outside finish: Epoxy paint connection: Flanges PN 10/16 Actuator: 1/4 turn Dimensions: ISO standards


Chapter ENGINEERING

Application date 16/11/1998



Page 2/3

Se0008.doc - OteroJ/oj 10/06/2011


Diamètres Code Application Spécifications Fournisseurs

Multiway Type: 4 way De zurik Stock at 1% Opening: Reduced / square Papiros consistency Body: Cast iron or equal And over Plug: Stainless steel VGX Stemm: Stainless steel Seal: metal/metal Outside finish: Epoxy paint connection: Flanges PN 10/16 Actuator: 1/4 turn

Dimensions: ISO standards

Isolating and Type: Butterfly valve Amri Control Opening: Through bore Keystone

Stock at less Body: Cast iron or equal than 1% Butterfly: Stainless steel consistency Stemm: Stainless steel

VP Seal: EPDM Outside finish: Epoxy paint

ND 65 and over

Connection: Between flanges PN 10/16 with centering lugs

Actuator: 1/4 turn with locking handle up to ND 125, and gear box when ND 150 and above

Dimensions: ISO standards

Control Type: Butterfly valve Tecofi Headbox inlet Opening: Through bore with flow Body: Stainless steel special Butterfly: Stainless steel finish VPI Stemm: Stainless steel Seal: Metal/metal Outside finish: Epoxy paint Connection: Flanges PN 10/16 Actuator: reducer Dimensions: ISO standards Inside finish: Cotton ball polished

Isolating and Type: 3 piece ball valve Gachot

Control Casing: Through bore Meca-inox Body: Stainless steel Mécafrance

ND 50 Ball: Stainless steel or equal and VB Stemm: Stainless steel

under Seal: PTFE Outside finish: Bare Connection: Butt weld Actuator: 1/4 turn Dimensions: ISO standards


Chapter ENGINEERING




Page 3/3

Se0008.doc - OteroJ/oj 10/06/2011



Isolating Type: Throught gate Tecofi pulpers Opening: Throught bore Vade Body: Cast iron Orbinox

DN 65 Gate: Stainless steel or equal et Stemm: Stainless steel

au-dessus VGF Seal: Metal/metal Outside finish : Epoxy paint Connection: Between flanges

PN 10/16

Actuator: Handwheel Dimensions: ISO standards

Pressure Type : Industrial pressure gage Bourdon Indication Boîtier : Stainless steel Wika Diameter: 100 mm or equal Connection: 1/2" BSP

All PI Assembly: To be defined Separator : Diaphragm

Food industry type Damping : Glycerine


Chapter ENGINEERING


Designation Valve spécifications WA

Page 1/1

0 16/11/1998 Emission B. BACUEZ L. PASCAL C. VANNUFFELEN


Se0009.doc - OteroJ/oj 10/06/2011


� PURPOSE

Recommendations for valve specifications. � APPLICATION FIELD

This instruction applies for stock preparation lines, approach systems and white water systems of paper mills in systems not over 8 bar pressure.

� SPECIFICATIONS


Isolating Type: Butterfly valve Amri and control Opening: Throught bore Keystone Body: Cast iron or equal Butterfly: Stainless steel Stemm: Stainless steel Seal: EPDM VP Outside finish: Epoxy paint connection: Between flanges PN 10/16

DN 65 and over

Actuator: 1/4 turn with locking handle up to ND 125 and gear box when ND 150 and above

Dimensions : ISO standards

Check Type: Swing check Amri Body: Stainless steel Keystone

Valve: Stainless steel or equal CV Seat: nitril

Outside finish: Bare connection: Between flanges PN 10/16 Dimensions: ISO standards

Isolating Type: 3 piece ball valve Gachot and control Opening: Throught bore Mécafrance Body: Stainless steel Méca-inox DN 32 to 50 VB Ball: Stainless steel or equal

Stemm: Stainless steel Seal: PTFE connection: Butt weld Actuator: 1/4 turn Dimensions: ISO standards

Isolating Type: Ball valve Gachot and control Opening: Reduced Mécafrance Body: Brass or equal

DN 20 Ball: Chromed brass and below VBL Stemm: Stainless steel

Seal: PTFE connection: BSP Actuator: 1/4 turn Dimensions: ISO standards

SE.001.B

SE.0009

Indice de révision 0

Rubrique ENGINEERING

Date d'application 12/10/1998

Désignation Spécifications robinetterie

WA – EAUX BLANCHES Classement Standard SM

Page 2/2

Se0009.doc - OteroJ/oj

10/06/2011

STANDARD



Chapter ENGINEERING


Designation Valve spécifications WAC

Page 1/1



Se0010.doc - OteroJ/oj 10/06/2011


� PURPOSE



� SPECIFICATIONS



DN 65 and over











SE.001.B

SE.0010






Page 2/2


10/06/2011

STANDARD



Chapter ENGINEERING


Designation Valve spécifications WAY

Page 1/1



Se0011.doc - OteroJ/oj 10/06/2011


� PURPOSE



� SPECIFICATIONS

Diamètres

diameter

Code Application Spécifications Fournisseurs

suppliers


DN 65 and over











SE.001.B

SE.0010






Page 2/2


10/06/2011

STANDARD



Chapter ENGINEERING


Designation Valve spécifications WAP

Page 1/1



Se0012.doc - OteroJ/oj 10/06/2011


� PURPOSE



� SPECIFICATIONS



DN 65 and over




Valve: or equal CV Seat: nitril







SE.001.B

SE.0010






Page 2/2


10/06/2011

STANDARD



Chapter ENGINEERING


Designation Valve spécifications WC

Page 1/1



Se0013.doc - OteroJ/oj 10/06/2011


� PURPOSE



� SPECIFICATIONS



DN 65 and over











SE.001.B SE.0010 STANDARD Indice de révision 0





Page 2/2


10/06/2011



Chapter ENGINEERING


Designation Valve spécifications WR

Page 1/1



Se0014.doc - OteroJ/oj 10/06/2011


� PURPOSE



� SPECIFICATIONS



DN 65 and over











SE.001.B

SE.0010






Page 2/2


10/06/2011

STANDARD



Chapter ENGINEERING


Designation Valve spécifications VH

Page 1/1



Se0015.doc - OteroJ/oj 10/06/2011


� PURPOSE



� SPECIFICATIONS



DN 65 and over











SE.001.B

SE.0010






Page 2/2


10/06/2011

STANDARD



Chapter ENGINEERING


Designation Valve spécifications API

Page 1/1



Se0016.doc - OteroJ/oj 10/06/2011


� PURPOSE



� SPECIFICATIONS



DN 65 and over











SE.001.B

SE.0010






Page 2/2


10/06/2011

STANDARD



Chapter ENGINEERING


Designation Valve spécifications APM

Page 1/1



Se0017.doc - OteroJ/oj 10/06/2011


� PURPOSE



� SPECIFICATIONS



DN 65 and over











SE.001.B

SE.0010






Page 2/2


10/06/2011

STANDARD


SE.001.B SE.0018 STANDARD Revision Number 1

Chapter ENGINEERING


Designation Pipe jacket detail

for refiners cooling Page

1/2

1 30/11/2001 Emission définitive

0 31/10/2001 Emission provisoire B. BACUEZ D. RATEL C. VANNUFFELEN


Se0018.doc - OteroJ/oj 10/06/2011

Classeme nt Standard SE

SE.001.B SE.0018 STANDARD Revision number 1

Chapter ENGINEERING


Designation Pipe jacket detail

for refiners cooling Classement Standard SM

Page 2/2


10/06/2011

File Standard SE

STANDARD SEG- 01

7 October 2004 1 (3)

CEILING SLEEVE

1 DIMENSIONS

STANDARD SEG- 001 7 October 2004 2(3)

CEILING SLEEVE No. of element 1 2

PIPE

Item Not insulated

Insulated up to temp.

360K


470K Pipe Flat bar Weld

Weight of sleeve

Hole in ceiling

DN DN DN OD x g kg/pcs. b x s x l pcs. kg/pcs. Material a x b kg/pcs. Ø

01 10 30.0 x 2.6 0.70 St 37.0 0.84 60

02 15 33.7 x 2.9 0.88 St 37.0 1.02

03 20 42.4 x 2.9 1.12 25 x 3 x 80 0.047 St 37.0 2.1 x 25 1.26 80

04 25 60.0 x 2.9 1.54 St 37.0 2.94 100

32 St 37.0

05 40 76.1 x 3.2 2.30 40 x 4 x 80 0.100 St 37.0 2.1 x 25 2.60 130

06 50 88.9 x 3.6 3.02 St 37.0 3.32

07 65 108.0 x 4.0 4.12 50 x 4 x 80 0.125 St 37.0 2.1 x 25 4.49 150

80 St 37.0

08 100 20 133.0 x 4.0 5.08 3 St 37.0 5.56 180

09 125 25 159.0 x 4.0 6.12 St 37.0 6.68 200

32 St 37.0

40 60 x 4 x 100 0.188 St 37.0 2.1 x 25

10 150 50 20 219.0 x 4.5 9.52 St 37.0 10.08 260

65 25 St 37.0

80 St 37.0

11 200 100 32 273.0 x 5.0 13.20 St 37.0 14.61 320

40 St 37.0

12 250 125 50 323.9 x 5.6 17.60 St 37.0 19.01 370

65 100 x 5 x 120 0.471 St 37.0 2.1 x 25

80 St 37.0

13 300 150 359.6 x 5.6 19.32 St 37.0 20.73 400

STANDARD SEG- 001 7 October 2004 3(3)

CEILING SLEEVE No. of element 1 2

PIPE

Item Not insulated


360K


470K Pipe Flat bar Weld

Weight of sleeve

Hole in ceiling

DN DN DN OD x g kg/pcs. b x s x l pcs. kg/pcs. Material a x b kg/pcs. Ø

14 350 100 406.4 x 6.3 24.88 RSt 37.2 26.91 450

125 120 x 6 x 120 0.678 RSt 37.2 2.1 x 25

15 400 200 150 457.0 x 6.3 28.00 RSt 37.2 30.03 500

16 450 250 200 508.0 x 7.1 35.08 RSt 37.2 37.11 550

17 500 300 250 610.0 x 7.1 42.40 RSt 37.2 45.79 650

550 350 300 3 RSt 37.2

18 600 400 350 711.0 x 8.0 55.60 RSt 37.2 59.00 750

650 450 150 x 8 x 120 1.130 RSt 37.2 2.1 x 25

19 700 500 400 813.0 x 8.0 63.60 RSt 37.2 67.00 850

750 450 RSt 37.2

20 800 250 500 914.0 x 8.0 71.60 RSt 37.2 75.00 970

2 DESIGNATION

Name, DN, material Example: Ceiling sleeve, 350 DN, St 37.0

STANDARD FOR PIPING Number Sheet ST-000 1(3) August, 2006

AUSTENITIC STAINLESS STEEL PIPING CURVE OF COEFFICIENT k 1 GENERAL This standard gives the curve for defining the allowable pressures in different

temperatures generally for Pipe classes and in detail for branch connections presented in standards ST-001/031.

2 LIMITATIONS The allowable pressure shall not exceed the nominal pressure of Pipe classes

10S...100S. In Pipe classes 4S and 6S the allowable pressure may exceed the nominal pressures 4 and 6 bar. The maximum allowable pressure is however 10 bar.

3 EXAMPLES Example 1: Pipe class 25S2A Temperature = 160°C Coefficient k = 0.86 The allowable pressure = 0.86 x 25 bar = 21.5 bar, which means that all

components of that Pipe class stand the pressure 21.5 bar. Example 2: Pipe class 6S2A Temperature = 20°C Coefficient k = 1.20 The allowable pressure = 1.20 x 6 bar = 7.2 bar, which means that the Pipe

class can be used up to 7.2 bar with the lapped flanges of PN 10. Example 3: Pipe class 10S2A Temperature = 40°C Coefficient k = 1.12 The allowable pressure ≠ 1.12 x 10 bar = 11.2 bar. The allowable pressure =

10 bar. Note! The flanges are according to PN 10.


AUSTENITIC STAINLESS STEEL PIPING CURVE OF COEFFICIENT k Example 4: Branch connection without reinforcement of Pipe class 25S2A, 273.0 x 219.1. Temperature = 160°C Coefficient k = 0.86 Allowable pressure from standard ST-027 Table 9 = 12.6 bar. The allowable pressure = 0.86 x 12.6 bar = 10.8 bar, which means that the

branch connection stands the pressure 10.8 bar. Example 5: Reinforced branch-connection of Pipe class 25S2A, 273.0 x 219.1 Temperature = 160°C Coefficient k = 0.86 Allowable pressure from standard ST-027 Table 10 = 18.3 bar. The allowable pressure = 0.86 x 18.3 bar = 15.7 bar, which means that the

branch connection stands the pressure 15.7 bar.


AUSTENITIC STAINLESS STEEL PIPING CURVE OF COEFFICIENT k 4 CURVE OF COEFFICIENT k


AUSTENITIC STAINLESS STEEL PIPING 1 GENERAL This standard presents dimension standards and material specifications for

piping components in austenitic stainless steel pipe classes. 2 PIPE CLASSES

Pipe

class

0S1A

0S2A

4S1A

4S2A

6S1A

6S2A

10S1A

10S2A

16S1A

16S2A

25S1A

25S2A

40S1A

40S2A

50S1A

50S2A

100S1A

100S2A

Design pressure (MPa) at 80°C

1) -0.1

0.4

0.6

1.0

1.6

2.5

4.0

5.0

10.0

1) Full vacuum, which corresponds 0.1 MPa external pressure


AUSTENITIC STAINLESS STEEL PIPING 3 PIPING COMPONENTS FOR 0S1A...100S1A

Piping components

Dimension standard

Material Remarks

Designation Standard NF EN 10204-

CERTIFICATE

Pipe ST-002 X2CrNi18-11

(Z3CN 18-10)

NF EN 10217-7 3.1B

Vacuum pipe ST-030 X2CrNi18-11

(Z3CN 18-10)

NF EN 10217-7 3.1B

Elbow ST-003 X2CrNi18-11

(Z3CN 18-10)

NF EN 10217-7 3.1B

Reducer ST-004 X2CrNi18-11

(Z3CN 18-10)

NF EN 10217-7 3.1B

Tee piece ST-011 X2CrNi18-11

(Z3CN 18-10)

NF EN 10217-7 3.1B

Collar ST-012 X2CrNi18-11

(Z3CN 18-10)

NF EN 10217-7 3.1B

Flange

See 5)

ST-020 S235JRG2

(BF 42)

NF EN 10025 Stamped Hot dip galvan.

Blind flange ST-010 S235JRG2

(BF 42)/

X2CrNi18-11

(Z3CN 18-10)

NF EN 10025/

NF EN 10217-7 Stamped Hot dip galvan.

Plate valve ST-013 X2CrNi18-11

(Z3CN 18-10)

NF EN 10217-7 Stamped

Hex head bolt 4) NF E 25-005 Strength class 8.8

NF A 35-557 Stamped Hot dip galvan.

Nut 4) NF EN 20898-2 Strength class 8 Stamped Hot dip galvan.

Washer NF E 25-514 steel Hot dip galvan.

Gasket NF E29-900-2

1) 3)

2)

1) Gasket thickness 1.5 mm. 2) Gasket material depends on flow substance. See Flow substances piping and valve material recommendation 00-A240-

20A/L12. 3) For pipe classes 50H1A dimension standard is NF E 29-900-3. For pipe class 100H1A dimension standard is NF E 29-900-6. 4) Material for hex head bolts and nuts in pipe in pipe classes 50H2A and 100H2A is 2C35 (XC38H1), NF EN 10083-1. For threaded rods dimension standard is NF E 25-136. 5) For Flange DN ≤ 200 - Material aluminium - AFNOR RS13 will be used.


AUSTENITIC STAINLESS STEEL PIPING 4 PIPING COMPONENTS FOR 0S2A...100S2A

Piping components

Dimension standard

Material Remarks


CERTIFICATE

Pipe ST-002 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Vacuum pipe ST-030 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Elbow ST-003 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Reducer ST-004 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Tee piece ST-011 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Collar ST-012 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Flange

See 5)

ST-020 S235JRG2

(BF 42)


Blind flange ST-010 S235JRG2

(BF 42)/

X2CrNi17-12-2

(Z2CN17-12)

NF EN 10025/

NF EN 10217-7 Stamped Hot dip galvan.

Plate valve ST-013 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 Stamped

Hex head bolt 4) NF E 25-005 Strength class 8.8


Nut 4) NF EN 20898-2 Strength class 8 Stamped Hot dip galvan.


Gasket NF E29-900-2

1) 3)

2)


20A/L12. 3) For pipe classes 50H2A dimension standard is NF E 29-900-3. For pipe class 100H2A dimension standard is NF E 29-900-6. 4) Material for hex head bolts and nuts in pipe in pipe classes 50H2A and 100H2A is 2C35 (XC38H1), NF EN 10083-1. For threaded rods dimension standard is NF E 25-136. 5) For Flange DN ≤ 200 - Material aluminium - AFNOR RS13 will be used.


AUSTENITIC STAINLESS STEEL PIPING 5 PIPING COMPONENTS FOR 10S2C, POLISHED, 0.4< Ra < 0.8

Piping components

Dimension standard

Material Remarks


CERTIFICATE

Pipe

406.4 x 5.0

457 x 5.0

508 x 5.0

X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Vacuum pipe

813 x 10.0

1016 x 10.0

1220 x 6.5

Elbow ST-003 3)

4)

X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Reducer ST-004 3) X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Tee piece ST-011 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Collar ST-012 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Flange

see 6)

5) S235JRG2

(BF 42)


Hex head bolt NF E 25-005 Strength class 8.8


Nut NF EN 20898-2 Strength class 8 Stamped Hot dip galvan.


Gasket NF E29-900-2

1)

2)


20A/L12. 3) Wall thickness same as pipe. 4) Alternative radius, R=3 x D. 5) Special guided flanges according to manufacturer. 6) For flange DN ≤ 200 - Material aluminium AFNOR RS13 will be used.


AUSTENITIC STAINLESS STEEL PIPING 6 PIPING COMPONENTS FOR 10S2D, ELECTRO POLISHED, Ra < /= 0.4

Piping components

Dimension standard

Material Remarks


CERTIFICATE

Pipe

406.4 x 5.0

457 x 5.0

508 x 5.0

X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

820 x 10.0

920 x 10.0

X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Elbow ST-003 3)

4)

X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Reducer 312-010 3) X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Tee piece 313-011 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Collar 314-013 X2CrNiMo17-12-2

(Z2CND 17-12)

NF EN 10217-7 3.1B

Flange

See 6)

5) S235JRG2

(BF 42)


Hex head bolt NF E 25-005 Strength class 8.8


Nut NF EN 20898-2 Strength class 8 Stamped Hot dip galvan.


Gasket NF E29-900-2

1)

2)


20A/L12. 3) Wall thickness same as pipe. 4) Alternative radius, R = 3 x D. 5) Special guided flanges according to manufacturer. 6) For flange DN ≤ 200 - Material aluminium AFNOR RS13 will be used.

STANDARD Number Sheet ST- 002 1(1) 7 October 2004

AUSTENITIC STAINLESS STEEL PIPING PIPES FOR PIPE CLASSES 4S...100S 1 DIMENSIONS

DN

Do x s

4S 6S 10S 16S 25S 40S 50S 100S

6 10.2 x 1.6 According to 4S

10 17.2 x 1.6 According to

15 21.3 x 1.6 4S 21.3 x 2.0

20 26.9 x 1.6 According to 26.9 x 2.6

25 33.7 x 1.6 4S 33.7 x 2.0 33.7 x 3.2

32 42.4 x 1.6 According to 42.4 x 2.6 42.4 x 4.0

40 48.3 x 1.6 4S 48.3 x 2.0 48.3 x 3.2 48.3 x 4.0

50 60.3 x 1.6 According to 60.3 x 2.6 60.3 x 4.0 60.3 x 5.0

(65) 76.1 x 1.6 4S 76.1 x 2.6 76.1 x 2.6 76.1 x 5.0 76.1 x 6.3

80 88.9 x 1.6 According to 88.9 x 2.6 88.9 x 3.2 88.9 x 5.0 88.9 x 8

100 114.3 x 2.0 4S 114.3 x 2.6 114.3 x 4.0 114.3 x 6.3 114.3 x 10

(125) 139.7 x 2.0 According 139.7 x 3.2 139.7 x 5.0 139.7 x 6.3

150 168.3 x 2.0 to 168.3 x 2.6 168.3 x 4.0 168.3 x 6.3 168.3 x 8.0

200 219.1 x 2.0 4S 219.1 x 2.6 219.1 x 3.2 219.1 x 5.0 219.1 x 8.0

250 273 x 2.0 273 x 2.6 273 x 4.0 273 x 6.3 273 x 10.0

300 323.9 x 2.6 323.9 x 3.2 323.9 x 5.0 323.9 x 8.0 323.9 x 12.5

350 355.6 x 2.6 355.6 x 3.2 355.6 x 5.0 355.6 x 8.0 355.6 x 12.5

400 406.4 x 2.6 406.4 x 4.0 406.4 x 6.3 406.4 x 10.0 406.4 x 14.2

(450) 457 x 3.2 457 x 4.0 457 x 6.3 457 x 10.0

500 508 x 3.2 508 x 5.0 508 x 8.0 508 x 12.5

600 610 x 4.0 610 x 6.3 610 x 10.0 610 x 14.2

700 711 x 4.0 711 x 6.3 711 x 10.0 711 x 16.0

800 813 x 4.0 813 x 5.0 813 x 8.0 813 x 12.5 813 x 17.5

900 914 x 4.0 914 x 5.0 914 x 8.0 914 x 12.5 914 x 20.0

1000 1016 x 4.0 1016 x 6.3 1016 x 10.0 1016 x 14.2 1016 x 22.0

1200 1220 x 6.3 1220 x 6.3

The nominal sizes inside parenthesis should be avoided. 2 DESIGNATION Name, Do x s, material, standard No. Example: Pipe, 114.3 x 2, X2 CrNiMo 17-12-2, ST-002


3 APPLICATION FIELD

This instruction applies to the following fluids: stock, white water, clarified white water, treated water and compressed air in systems not over 100°C temperature, and according to pressure class from PN 4 (4S) up to PN 100 (100S)

4 MATERIAL SPECIFICATIONS

Welded rolled or cold drawn pipe and according to project specifications, acceptable material specifications include: - AISI 304 - AISI 304 L - AISI 316 - AISI 316 L or equivalent. Inside wall finish: Ra 0,8 to 1,2 µ unless otherwise specified.


AUSTENITIC STAINLESS STEEL PIPING ELBOWS FOR PIPE CLASSES 0S...100S 1 DIMENSIONS Table 1 Dimensions

according to pipe classes

DN

Do x s R Type

0S, 4S 6S 10S 16S 25S 1.5D 2.5D

6 10.2 x 2.0 R=3...5xDN Elbow or bent pipe

10 17.2 x 2.0 26

15 21.3 x 2.0 Accoding to 29

20 26.9 x 2.0 Accoding to 4S 32 58

25 33.7 x 2.0 4S 38 73

32 42.4 x 2.0 48 93

40 48.3 x 2.0 57 108

50 60.3 x 2.0 According to 60.3 x 2.6 76 135

(65) 76.1 x 2.0 4S 76.1 x 3.2 95 175

80 88.9 x 2.6 88.9 x 3.2 114 205

100 114.3 x 2.6 According to 114.3 x 4.0 152 270

(125) 139.7 x 2.6 4S 139.7 x 3.0 139.7 x 5.0 190 330

150 168.3 x 2.6 168.3 x 4.0 168.3 x 5.0 229 390 R = 1.5D or

200 219.1 x 2.6 219.1 x 3.2 219.1 x 5.0 219.1 x 6.3 305 510 R = 2.5D

250 273 x 3.2 273 x 4.0 273 x 6.3 273 x 8.0 381 650 Pressed elbow

300 323.9 x 3.2 323.9 x 4.0 323.9 x 6.3 323.9 x 10.0 457 775

350 355.6 x 3.2 355.6 x 5.0 355.6 x 8.0 355.6 x 10.0 533 850

400 406.4 x 4.0 406.4 x 5.0 406.4 x 8.0 406.4 x 12.5 610 970

(450) 457 x 4.0 457 x 6.3 457 x 8.0 457 x 12.5 686 1123

500 508 x 4.0 508 x 6.3 508 x 10.0 508 x 14.2 762 1245

600 610 x 4.0 610 x 5.0 610 x 8.0 610 x 12.5 610 x 17.5 914 1524

(700) 711 x 5.0 711 x 5.0 711 x 8.0 711 x 12.5 711 x 20.0 1070 R = 1.5D

800 813 x 5.0 813 x 6.3 813 x 10.0 813 x 14.2 813 x 22.5 1220 Miter elbow

(900) 914 x 6.3 914 x 8.0 914 x 10.0 914 x 17.5 914 x 25.0 1370

1000 1016 x 6.3 1016 x 8.0 1016 x 12.5 1016 x 20.0 1016 x 28.0 1525

1200 1220 x 8.0 1220 x 10.0 1830


AUSTENITIC STAINLESS STEEL PIPING ELBOWS FOR PIPE CLASSES 0S...100S

DN

Do x s R

Type

40S 50S 100S

6 10.2 x 2.0 According to According to

10 17.2 x 2.0 4S 4S

15 21.3 x 2.0 3..5 x DN Bent

20 26.9 x 2.0 26.9 x 2.6 26.9 x 3.2 pipe

25 33.7 x 2.0 33.7 x 2.6 33.7 x 5.0 or elbow

32 42.4 x 2.0 42.4 x 3.2 42.4 x 6.3 48

40 48.3 x 2.6 48.3 x 4.0 48.3 x 6.3 57

50 60.3 x 3.2 60.3 x 5.0 60.3 x 8.0 76

(65) 76.1 x 4.0 76.1 x 6.3 76.1 x 10.0 95

80 88.9 x 5.0 88.9 x 8.0 88.9 x 12.5 114 R = 1.5D

100 114.3 x 6.3 114.3 x 10.0 114.3 x 14.2 152

(125) 139.7 x 8.0 139.7 x 10.0 190

150 168.3 x 8.0 168.3 x 10.0 229

200 219.1 x 10.0 305

250 273 x 12.5 381

300 323.9 x 14.2 457

350 355.6 x 17.5 533

400 406.4 x 17.5 610

The nominal sizes inside parenthesis shall be avoided. 2 DESIGNATION Name, Do x s, R, material, standard No. Example: Elbow, 219.1 x 2.6, 305, X2 CrNiMo 17-12-2, ST- 003

STANDARD Number Sheet ST-004 1(5) 7 October 2004

AUSTENITIC STAINLESS STEEL PIPING REDUCERS FOR PIPE CLASSES 0S...100S 1 DIMENSIONS See the following table for dimensions.

L = 2.96 x (Do1 - Do2) 2 SUDDEN REDUCER Sudden reducer to be used for pulp on suction side of a pump. Type S1 For pipelines connected to a tank height < 10 m


AUSTENITIC STAINLESS STEEL PIPING REDUCERS FOR PIPE CLASSES 0S...100S Type S2 For pipelines connected to a tower

3 NOTE The wall thickness is at least the same as the wall thickness of the pipe at the

bigger end of the reducer, however at least 2 mm. 4 DESIGNATION Name, type, DN1/DN2 x s, material, standard No. Example: Reducer, C, 500/350 x 3.2, X2CrNiMo 17-12-2 , ST- 004


AUSTENITIC STAINLESS STEEL PIPING REDUCERS FOR PIPE CLASSES 0S...100S 5 DIMENSIONS FOR PIPE CLASSES 0S...100S

DN1

DN2

Do1

Do2

L

Wall thickness

0S 4S 6S

10S 16S 25S 40S 50S 100S

25 10 15 20

33.7 17.2 21.3 26.9

49 37 20

2.0 2.0 2.0

According to 4S

According to 4S

3.2 3.2 3.2

32 10 15 20 25

42.4 17.2 21.3 26.9 33.7

75 62 46 26

2.0 2.0 2.0 2.0

According

to 4S

2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

40 15 20 25 32

48.3 21.3 26.9 33.7 42.4

80 63 43 18

2.0 2.0 2.0 2.0

According

According

2.0 2.0 2.0 2.0

3.2 3.2 3.2 3.2

4.0 4.0 4.0 4.0

50 20 25 32 40

60.3 26.9 33.7 42.4 48.3

99 79 53 35

2.0 2.0 2.0 2.0

to 4S to 4S 2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

5.0 5.0 5.0 5.0

(65) 25 32 40 50

76.1 33.7 42.4 48.3 60.3

126 100 82 47

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

2.6 2.6 2.6 2.6

5.0 5.0 5.0 5.0

6.3 6.3 6.3 6.3

80 32 40 50 (65)

88.9 42.4 48.3 60.3 76.1

138 120 84 38

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

3.2 3.2 3.2 3.2

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

100 40 50 (65) 80

114.3 48.3 60.3 76.1 88.9

195 160 113 75

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

10.0 10.0 10.0 10.0

(125) 50 (65) 80 100

139.7 60.3 76.1 88.9 114.3

234 188 150 75

2.0 2.0 2.0 2.0

3.2 3.2 3.2 3.2

5.0 5.0 5.0 5.0

6.3 6.3 6.3 6.3

150 (65) 80 100 (125)

168.3 76.1 88.9 114.3 139.7

273 234 160 85

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

8.0 8.0 8.0 8.0


AUSTENITIC STAINLESS STEEL PIPING REDUCERS FOR PIPE CLASSES 0S...100S

DN1

DN2

Do1

Do2

L

Wall thickness

0S 4S 6S

10S 16S 25S 40S

200 80 100 (125) 150

219.1 88.9 114.3 139.7 168.3

385 309 234 150

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

3.6 3.6 3.6 3.6

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

250 100 (125) 150 200

273.0 114.3 139.7 168.3 219.1

470 394 309 159

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

10.0 10.0 10.0 10.0

300 (125) 150 200 250

323.9 139.7 168.3 219.1 273.0

545 459 309 150

2.0 2.0 2.0 2.0

3.2 3.2 3.2 3.2

4.5 4.5 4.5 4.5

8.0 8.0 8.0 8.0

12.5 12.5 12.5 12.5

350 150 200 250 300

355.6 168.3 219.1 273.0 323.9

554 403 244 94

2.6 2.6 2.6 2.6

3.2 3.2 3.2 3.2

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

12.5 12.5 12.5 12.5

400 200 250 300 350

406.4 219.1 273.0 323.9 355.6

554 394 244 150

2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

10.0 10.0 10.0 10.0

14.2 14.2 14.2 14.2

(450) 250 300 350 400

457.0 273.0 323.9 355.6 406.4

544 394 300 150

3.2 3.2 3.2 3.2

4.0 4.0 4.0 4.0

8.0 8.0 8.0 8.0

10.0 10.0 10.0 10.0

500 300 350 400 (450)

508.0 323.9 355.6 406.4 457.0

544 450 300 150

3.2 3.2 3.2 3.2

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

12.5 12.5 12.5 12.5

600 350 400 (450) 500

610.0 355.6 406.4 457.0 508.0

750 600 450 300

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

10.0 10.0 10.0 10.0

14.2 14.2 14.2 14.2

(700) 400 (450) 500 600

711.0 406.4 457.0 508.0 610.0

900 750 600 300

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

10.0 10.0 10.0 10.0

16.0 16.0 16.0 16.0


AUSTENITIC STAINLESS STEEL PIPING REDUCERS FOR PIPE CLASSES 0S...100S

DN1

DN2

Do1

Do2

L

Wall thickness

0S 4S

6S 10S 16S 25S

800 (450) 500 600 (700)

813.0 457.0 508.0 610.0 711.0

1053 900 600 300

4.0 4.0 4.0 4.0

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

12.5 12.5 12.5 12.5

19.0 19.0 19.0 19.0

(900) 500 600 (700) 800

914.0 508.0 610.0 711.0 813.0

1205 900 600 300

4.0 4.0 4.0 4.0

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

14.2 14.2 14.2 14.2

21.0 21.0 21.0 21.0

1000 600 700 800 (900)

1016.0 610.0 711.0 813.0 914.0

1205 900 600 300

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

10.0 10.0 10.0 10.0

16.0 16.0 16.0 16.0

23.0 23.0 23.0 23.0

1200 (700) 800 (900) 1000

1220.0 711.0 813.0 914.0 1016.0

1506 1205 900 600

6.3 6.3 6.3 6.3

6.3 6.3 6.3 6.3


AUSTENITIC STAINLESS STEEL PIPING PRESSED COLLAR FOR PIPE CLASSES 0S, 4S, 6S AND 10S 1 APPLICATION Range of use: 0S DN 10...DN 150 4S DN 10...DN 150 6S DN 10...DN 150 10S DN 10...DN 100 2 DIMENSIONS

DN du D h R b s

10 15 20

17.2 21.3 26.9

42 47 58

6 6

7

3 3 3

2 2 2

1.6 1.6 1.6

25 32 40

33.7 42.4 48.3

68 78 88

9 10 10

3 3 3

2 2 2

1.6 1.65 1.7

50 (65) 80

60.3 76.1 88.9

102 122 133

12 12 14

3 3 3

2 2 2.9

1.7 1.7 1.75

100 (125) 150

114.3 139.7 168.3

158 184 212

14 15 19

3 4 4

2.9 2.9 2.9

2.7 2.7 2.7


AUSTENITIC STAINLESS STEEL PIPING PRESSED COLLAR FOR PIPE CLASSES 0S, 4S, 6S AND 10S 3 NOTES Pressed collars are allowed only for harmless fluids. For dangerous fluids welded collars shall be used. 4 DESIGNATION Name, PN-DN x Do, material, standard No. Example: Pressed collar, PN 6-100 x 114.3, X2CrNiMo 17-12-2, ST-005


AUSTENITIC STAINLESS STEEL PIPING LOOSE FLANGE FOR PIPE CLASSES 4S, 6S AND 10S

ST-006


AUSTENITIC STAINLESS STEEL PIPING LOOSE FLANGE FOR PIPE CLASSE 16S

ST-007



ST-008



ST-009


AUSTENITIC STAINLESS STEEL PIPING BLIND FLANGE 0S...25S 1 DIMENSIONS

2 1 Plate Ø Dt, s = 2 X2CrNiMo 17-12-2

(Z2 CND 17-12)

1 1 Blind flange TYPE 05 A S235JRG2 (BF 42)

Part Pcs Description Dimensions Material

DN

0S...10S

16S

25S

h Dt h Dt h Dt

10 16 40 16 40 16 40

15 16 45 16 45 16 45

20 18 58 18 58 18 58

25 18 66 18 66 18 66

32 20 77 20 77 20 77

40 20 87 20 87 20 87

50 20 102 20 102 22 102

65 22 122 22 122 24 122

80 22 137 22 137 26 137

100 24 157 24 157 28 163

125 24 187 24 187 30 189

150 26 213 26 213 32 219

200 26 268 28 268 34 279

250 28 323 28 324 34 335

300 28 373 30 379 36 395

350 28 433 32 439 40 452

400 30 484 34 490 42 509

450 30 534 38 550 46 559

500 32 589 42 612 50 619


AUSTENITIC STAINLESS STEEL PIPING BLIND FLANGE 0S...25S 2 DESIGNATION Name, DN, pressure class of pipe class, material of the flange, material of

lining plate, standard No. Example: Blind flange, DN 250, PN 16, S235JRG2, X2CrNiMo 17-12-2,

ST-010


AUSTENITIC STAINLESS STEEL PIPING PLATE VALVE 1 GENERAL Plate valve shall be used between flanges instead of shut valve. 2 DIMENSIONS

DN 4S2A...10S2A

A B C D E R S MPa 50 56 102 102 125 18 15 5 1.0 65 72 122 70 145 18 15 5 1.0 80 85 133 80 160 18 15 5 1.0 100 110 158 90 180 18 15 5 0.6 125 135 184 90 210 18 15 6 0.7 150 164 212 90 240 23 15 8 1.0 200 214 268 90 295 23 15 8 0.6 250 263 320 140 350 23 15 10 0.6 300 320 370 140 400 23 15 10 0.6 350 350 430 140 460 23 15 16 1.0 400 400 482 140 515 27 15 16 0.6 500 500 585 150 620 27 15 16 0.6 600 602 685 150 725 30 15 16 0.4

3 DESIGNATION Name, DN, standard No. Example: Plate valve, DN 250, ST-013


CARBON AND STAINLESS STEEL THREADED FITTINGS NIPPLES NIPPLE (WITH PARALLEL THREAD), DIN 2982 TABLE 1 3122

Connection DN

inches

Length L mm

6 8 10

1/8 1/4 3/8

16 18 22

15 20 25

1/2 3/4 1

25 30 35

32 40 50

1 1/4 1 1/2 2

38 38 45

65 80

2 1/2 3

55 60

BARREL NIPPLE, DIN 2982 3130 TABLE 2

Connection DN

inches

Length L mm

6 8 10

1/8 1/4 3/8

40 40 40

15 20 25

1/2 3/4 1

60 60 60

32 40 50

1 1/4 1 1/2 2

80 80 100

65 80

2 1/2 3

100 120


CARBON AND STAINLESS STEEL THREADED FITTINGS NIPPLES SCREWED END 3011 TABLE 3

Connection DN

inches

Length L mm

6 8 10

1/8 1/4 3/8

30 30 30

15 20 25

1/2 3/4 1

35 40 40

32 40 50

1 1/4 1 1/2 2

50 50 55

65 80

2 1/2 3

60 65

HEXAGON NIPPLE, DIN 2990 3012 TABLE 4

Connection DN

inches

Length L mm

Width across flats N mm Hexagon

Octagon

6 8 10

1/8 1/4 3/8

22 28 30

12 14 19

15 20 25

1/2 3/4 1

38 42 48

22 30 36

32 40 50

1 1/4 1 1/2 2

54 55 64

46 50 65

65 80

2 1/2 3

75 82

80 90


CARBON AND STAINLESS STEEL THREADED FITTINGS NIPPLES LONG SCREW INCLUDING SOCKET AND BACKNUT, DIN 2981 3118 TABLE 5

Connection DN

inches

Centre to end L mm

Length thread parallel lmm

6 8 10

1/8 1/4 3/8

75 80 100

30 35 40

15 20 25

1/2 3/4 1

100 120 140

50 55 60

32 40 50

1 1/4 1 1/2 2

150 150 170

70 70 81

65 80

2 1/2 3

180 200

92 101


CARBON AND STAINLESS STEEL THREADED FITTINGS UNIONS UNION WITH INTERNAL THREAD AND PLANE FACES, DIN 2993 3031 TABLE 1

Connection DN

inches

Length L mm


Octagon

6 8 10

1/8 1/4 3/8

38 42 45

27 27 32

15 20 25

1/2 3/4 1

48 52 58

41 50 55

32 40 50

1 1/4 1 1/2 2

65 70 72

70 75 85

65 80

2 1/2 3

78 86

115 130

UNION WITH INTERNAL THREAD AND TAPERED FACES, DIN 2993 3022 TABLE 2

Connection DN

inches

Length L mm


Octagon

6 8 10

1/8 1/4 3/8

38 42 45

27 27 32

15 20 25

1/2 3/4 1

48 52 58

41 50 55

32 40 50

1 1/4 1 1/2 2

65 70 72

70 75 85

65 80

2 1/2 3

78 86

115 130


CARBON AND STAINLESS STEEL THREADED FITTINGS UNIONS UNION WITH ONE INTERNAL AND ONE EXTERNAL THREAD AND PLANE FACES 3030 TABLE 3

Connection DN

inches

Length L mm


Octagon

6 8 10

1/8 1/4 3/8

45 55 58

27 27 32

15 20 25

1/2 3/4 1

66 72 80

41 50 55

32 40 50

1 1/4 1 1/2 2

90 95 100

70 75 85

65 80

2 1/2 3

115 125

115 130

UNION WITH ONE INTERNAL AND ONE EXTERNAL THREAD AND TAPER FACES 3032 TABLE 4

Connection DN

inches

Length L mm


Octagon

6 8 10

1/8 1/4 3/8

45 55 58

27 27 32

15 20 25

1/2 3/4 1

66 72 80

41 50 55

32 40 50

1 1/4 1 1/2 2

90 95 100

70 75 85

65 80

2 1/2 3

115 125

115 130


CARBON AND STAINLESS STEEL THREADED FITTINGS UNIONS UNION, BUTT WELD ENDS, WITH TAPER FACES 3020 TABLE 5

Welding end O.D./l.D mm

Length L mm


Octagon

14/10 18/14 21.3/17

42 48 51

27 32 41

25/21 26.9/23 30/25

51 55 55

41 50 50

34/29.7 39/34 44.5/39.2

60 60 68

55 55 70

48.3/41.9 52/45.8 54/50

68 72 72

70 75 75

60.3/52 77/71 89/81.7

75 83 90

90 110 130


AUSTENITIC STAINLESS STEEL PIPING VACUUM PIPES, PIPE CLASS 0S 1 DIMENSIONS

DN Do s Lmax b x h

200 219.1 2.0 1900 40 x 6

250 273 2.0 1750 40 x 6

300 323.9 2.6 2200 40 x 6

350 355.6 2.6 2300 40 x 6

400 406.4 2.6 1600 40 x 6

(450) 457 3.2 2800 40 x 6

500 508 3.2 1900 40 x 6

600 610 4.0 2600 60 x 8

700 711 4.0 2340 60 x 8

800 813 4.0 1750 60 x 8

900 914 4.0 1490 60 x 8

1000 1016 4.0 1280 60 x 10

1200 1220 6.3 2950 60 x 10


AUSTENITIC STAINLESS STEEL PIPING VACUUM PIPES, PIPE CLASS 0S 2 NOTES 1 Lenght of the welds on both sides of the ring must be at least 0.5 x

circumference of the pipe. When using intermittent weld the distance between welds must not exceed

8 x wall thickness of the pipe. 2 Nominal sizes DN 6 - DN 150 do not need any reinforcement against

vacuum when the wall thicknesses are according to the pipe class 4S. Extra reinforcement rings must be welded on to the pipe at both ends near

bends. 3 DESIGNATION Name, Do x s, material, standard No. Example: Vacuum pipe, 406.4 x 2.6, X2CrNiMo 17-12-2, ST-030

Date post:	31-Dec-2015
Category:	Documents
Upload:	nofrialdie
View:	45 times
Download:	7 times

SS piping

Documents