Tranquility Console (TRC) Series - Climate Master...Jul 14, 2006 · ClimateMaster works...

ClimateMaster works continually to improve its products. As a result, the design and specifications of each product at the time of order may be changed without notice and may not be as described herein. Please contact ClimateMaster's Customer Service Department at 1-405-745-6000 for specific information on the current design and specifications. Statements and other information contained herein are not express warranties and do not form the basis of any bargain between the parties, but are merely ClimateMaster's opinion or commendation of its products. The latest version of this document is available at climatemaster.com.

*LC386* LC386 Rev.: December 14, 2020

Tranquility® Console (TRC) SeriesSubmittal DataModels TRC09-18 60Hz - HFC-410A


Page ______ of ______LC386 - 2

Unit Features, Options and Accessories 3Selection Procedure 4

TRC Series Nomenclature 6Performance Data – AHRI/ASHRAE/ISO 13256-1 8

Performance Data – Selection Notes 9Performance Data – TRC09 10Performance Data – TRC12 11Performance Data – TRC15 12Performance Data – TRC18 13

Performance Data Correction Tables 14Antifreeze Correction Table 15

Blower Performance & Electrical Data 17Physical Data 18

Console Cabinet Dimensions – Size 09-15: Bottom Return – Left Hand Piping 19Console Cabinet Dimensions – Size 09-15: Front Return – Left Hand Piping 20

Console Cabinet Dimensions – Size 09-15: Bottom Return – Right Hand Piping 21Console Cabinet Dimensions – Size 09-15: Front Return – Right Hand Piping 22

Console Chassis Dimensions – Size 09-15: Bottom Return 23Console Chassis Dimensions – Size 09-15: Front Return 24

Piping Details – Size 09-15 25Console Cabinet Dimensions – Size 18: Bottom Return – Left Hand Piping 26

Console Cabinet Dimensions – Size 18: Front Return – Left Hand Piping 27Console Cabinet Dimensions – Size 18: Bottom Return – Right Hand Piping 28

Console Chassis Dimensions – Size 18: Front Return – Right Hand Piping 29Console Chassis Dimensions – Size 18: Bottom Return 30

Console Chassis Dimensions – Size 18: Front Return 31Piping Detail – Size 18 32

TRC Series Wiring Diagram Matrix 33Typical Wiring Diagram – Manual & Auto Change Over TRC Units with CXM Controller 34

Typical Wiring Diagram – Remote Mounted Thermostat TRC Units with CXM Controller 35Typical Wiring Diagram – TRC Units with CXM & MPC Controller 36

Typical Wiring Diagram – Manual & Auto Change Over TRC Units with DXM Controller 37Typical Wiring Diagram – Remote Mounted Thermostat TRC Units with DXM Controller 38

Engineering Specifications 39Performance Sheet 49

Revision History 51

Table of Contents

TRC Console Series

Document page number is shown next to part number (e.g. LC386 - 3 = page 3). Since not all pages are typically used in the submittals process, the page number in the lower right corner can still be used (page ____of_____).


Page ______ of ______LC386 - 3

Unit Features, Options and Accessories

TRANQUILITY® CONSOLE (TRC) SERIES WITH EARTHPURE® HFC-410A REFRIGERANT

The Tranquility® Series (TRC) console unit provides a high efficiency WSHP “ductless” solution for spaces where individual, quiet control of the heating and cooling system is important. TRC units are especially ideal where ceiling height and space are limited, or when preserving the integrity of an existing structure. The TRC Series exceeds ASHRAE 90.1 efficiencies, yet maintains small cabinet dimensions. Using EarthPure® HFC-410A refrigerant, the Tranquility console not only protects the environment, it does so while delivering unprecedented comfort, efficiency, and reliability.

Available in sizes 3/4 ton (2.64 kW) through 1-1/2 tons (5.3 kW) with numerous cabinet, water piping and control choices, the TRC Series offers a wide range of units for most any installation. The TRC has an extended range refrigerant circuit, capable of ground loop (geothermal) applications as well as water loop (boiler-tower) applications. Standard features are many. Microprocessor controls, galvanized steel cabinet, polyester powder coat paint and TXV refrigerant metering device are just some of the features of the flexible TRC series.

Compressors are mounted on specially engineered sound-tested EPDM grommets for quiet operation. Options such as coated air coil, DDC controls, internal pump and factory-installed water solenoid valves allow customized design solutions.

The TRC Series console water-source heat pumps are designed to meet the challenges of today’s HVAC demands with a low cost/high value “ductless” solution.

UNIT FEATURES• Sizes 09 (3/4 ton, 2.64 kW) through 18 (1-1/2 ton,

5.3 kW• Environmentally-friendly EarthPure® (HFC-410A) zero

ozone depletion refrigerant• High Efficiency Rotary compressors• Exceeds ASHRAE 90.1 efficiencies• Two-piece chassis/cabinet design • Galvanized steel cabinet with durable Polar Ice powder

coat finish• Slope top/aluminum rigid bar supply air grille• TXV metering device • Extended range (20 to 120°F, -6.7 to 48.9°C) operation• Microprocessor controls with 8 standard safeties• Right or left-hand piping arrangement• Front or bottom return air configuration• Unit Performance Sentinel™ performance monitoring

system

OPTIONS• Unit subbase with black matte finish

- Available with or without fresh air motorized damper• UltraQuiet sound attenuation package• Digital auto change-over unit mounted controls with

temperature display and high/low fan speed selection • Remote-mounted controls• DXM advance unit controller• LonWorks, BACnet (MSTP), Modbus and Johnson N2

compatibility options for DDC controls• Unit integrated power disconnect • Easy to clean rust prohibitive stainless steel drain pans • Extended range insulation for geothermal applications • Auto flow regulators that limit water flow to the unit

preventing system over pumping • Two-way motorized water valves that prevent water

flow through the unit when it is not in operation increasing system pumping efficiency

• Internally mounted water pump for single pipe systems • Corrosive resistant cupro-nickel water heat exchanger • E-Coated air coils for added protection• 115/60/1 voltage

- With or without 20 AMP plug and cord• Locking control door • No cabinet, chassis only replacements• Extended cabinets• LonWorks, BACnet, Modbus and Johnson N2

compatibility options for DDC controls

ACCESSORIES• Louvered, painted black “matte” finish subbase

decorative grille for field-installation.• Accessory subbases


Page ______ of ______LC386 - 4

Selection Procedure

Reference Calculations

LWT = EWT -HE

GPM x 500

LAT = EAT +HC

CFM x1.08

LWT = EWT +HR

GPM x 500

LAT (DB) = EAT (DB) - SCCFM x1.08

LC = TC - SC

S/T =SCTC

Heating Cooling

Conversion Table - to convert inch-pound (English) to S-I (Metric)Air Flow Water Flow Est Static Pressure Water Pressure Drop

Airfl ow (L/s) = CFM x 0.472 Water Flow (L/s) = gpm x 0.0631 ESP (Pa) = ESP (in of wg) x 249 PD (kPa) = PD (ft of hd) x 2.99

BTUH = BTU (British Thermal Unit) per hour MBTUH = 1,000 BTU per hour TC = total cooling capacity, BTUH SC = sensible cooling capacity, BTUH S/T = sensible to total cooling ratio LC = latent cooling capacity, BTUH HC = air heating capacity, BTUH CFM = airflow, cubic feet/minute ESP = external static pressure (inches w.g.) EAT = entering air temperature LAT = leaving air temperature, °F DB = dry bulb temperature (°F) WB = wet bulb temperature (°F) EWT = entering water temperature LWT = leaving water temperature, °F TD or delta T = temperature differential

GPM = water flow in U.S. gallons/minute WPD = waterside pressure drop (psi & ft. of hd.) HE = total heat of extraction, BTUH HR = total heat of rejection, BTUH KW = total power unit input, kilowatts EER = energy efficient ratio = BTUH output/Watt input COP = coefficient of performance = BTUH output/BTUH input MPT = male pipe thread FPT = female pipe thread HWC = hot water generator (desuperheater) capacity, Mbtuh ECM-CV = electronic commutated constant volume fan motor ECM-CT = electronic commutated constant torque fan motor MWV = motorized water valve WSE = waterside economizer VFD = variable frequency drive

Legend and Glossary of Abbreviations


Page ______ of ______LC386 - 5

Selection Procedure

Step 1 Determine the actual heating and cooling loads at the desired dry bulb and wet bulb conditions.

Step 2 Obtain the following design parameters: Entering water temperature, water flow rate in GPM, air flow in CFM, water flow pressure drop and design wet and dry bulb temperatures. Air flow CFM should be between 300 and 450 CFM per ton. Unit water pressure drop should be kept as close as possible to each other to make water balancing easier. Go to the appropriate tables and find the proper indicated water flow and water temperature.

Step 3 Select a unit based on total and sensible cooling conditions. Select a unit which is closest to, but no larger than, the actual cooling load.

Step 4 Enter tables at the design water flow and water temperature. Read the total and sensible cooling capacities (Note: interpolation is permissible, extrapolation is not).

Step 5 Read the heating capacity. If it exceeds the design criteria it is acceptable. It is quite normal for Water-Source Heat Pumps to be selected on cooling capacity only since the heating output is usually greater than the cooling capacity.

Step 6 Determine the correction factors associated with the variable factors of dry bulb and wet bulb.

Corrected Total Cooling = tabulated total cooling x wet bulb correction.

Corrected Sensible Cooling = tabulated sensible cooling x wet/dry bulb correction.

Step 7 Compare the corrected capacities to the load requirements. Normally if the capacities are within 10% of the loads, the equipment is acceptable. It is better to undersize than oversize, as undersizing improves humidity control, reduces sound levels and extends the life of the equipment.

Step 8 When completed, calculate water temperature rise and assess the selection. If the units selected are not within 10% of the load calculations, then review what effect changing the GPM, water temperature and/or air flow and air temperature would have on the corrected capacities. If the desired capacity cannot be achieved, select the next larger or smaller unit and repeat the procedure. Remember, when in doubt, undersize slightly for best performance.

Example Equipment Selection For CoolingStep 1 Load Determination:Assume we have determined that the appropriate cooling load at the desired dry bulb 80°F and wet bulb 65°F conditions is as follows:

Total Cooling...........................................................10,200 BTUH

Sensible Cooling.......................................................8,350 BTUH

Entering Air Temp.......................80°F Dry Bulb/65°F Wet Bulb

Step 2 Design Conditions:Similarly, we have also obtained the following design parameters:

Entering Water Temp............................................................90°F

Water Flow (Based upon 12°F rise in temp.)...............2.3 GPM

Air Flow.......................................................................... 350 CFM

Steps 3, 4 & 5 HP Selection:After making our preliminary selection (TRC12), we enter the tables at design water flow and water temperature and read Total Cooling, Sens. Cooling and Heat of Rej. capacities:

Total Cooling...........................................................10,800 BTUH

Sensible Cooling.......................................................9,200 BTUH

Heat of Rejection....................................................13,900 BTUH

Steps 6 & 7 Entering Air and Airflow Corrections:Next, we determine our correction factors.

Table Ent Air Air Flow CorrectedCorrected Total Cooling = 10,800 x 0.976 x 0.954 =10,056

Corrected Sens Cooling = 9,200 x 1.071 x 0.927 = 9,134

Corrected Heat of Reject = 13,900 x 0.979 x 0.958 = 13,037

Step 8 Water Temperature Rise Calculation and Assessment:

Actual Temperature Rise.....................................................11.3°F

When we compare the Corrected Total Cooling and Corrected Sensible Cooling figures with our load requirements stated in Step 1, we discover that our selection is within +/- 10% of our sensible load requirement. Furthermore, we see that our Corrected Total Cooling figure is slightly undersized as recommended, when compared to the actual indicated load.


Page ______ of ______LC386 - 6

TRC Series Nomenclature

Table Continue on Next Page

Section PositionDigit Value Description

Series 1-3 TRC Tranquility Console Series

Unit Size 4-5 06 06 - .5 ton

09 09 - .75 ton12 12 - 1 ton15 15 - 1.25 ton18 18 - 1.5 ton

Revision 6 B Revision Level

Voltage 7 G 208-230/60/1

A 115/60/1E 265/60/1

Controls 8 C ACO Unit Mounted Thermostat w/CXM

D ACO Unit Mounted Thermostat w/DXMR Remote Mounted Thermostat w/CXMS Remote Mounted Thermostat w/DXML Remote Mounted Thermostat w/CXM & LONM Remote Mounted Thermostat w/DXM & LONN Remote Mounted Thermostat w/CXM & MPCP Remote Mounted Thermostat w/DXM & MPC

Power Termination 9 A Field Connected (Hard Wired)

B 20 Amp Plug & CordD BreakerF Dissconnect SwitchK 20 Amp Plug & Cord, Disconnect Switch, & Receptacle

Cabinet Construction 10 Option Bottom Return

Front Return

Locking Control Door Ultra-Quiet No Cabinet,

Chassis Only Extended Cabinet

S

Yes No

No

NoNo

NoR YesN Yes NoA

Yes

No YesC Yes

NoM

No

D

YesK YesL

No

NoT YesF

No Yes

No

NoU YesH Yes

NoB

Yes

No P YesJ Yes

NoE

Yes NoQ YesG

NoNo

V Yes


Page ______ of ______LC386 - 7

TRC Series Nomenclature

Table Continue from Previous Page

Section PositionDigit Value Description

Subbase 11 S 5” Subbase

H 5” Subbase w/Motorized DamperN None1 5” Subbase - Chassis Only2 5” Subbase w/Motorized Damper - Chassis Only3 5” Subbase Extended Length Cabinet4 5” Subbase w/Motorized Damper Extended Length Cabinet

Heat Exchanger 12 A Copper Water Coil & E-Coated Air Coil

C Copper Water Coil & Standard Air Coil J Cupro-Nickel Water Coil & E-Coated Air CoilN Cupro-Nickel Coil & Standard Air CoilV Copper Water Coil & E-Coated Air Coil w/Extended Range InsulationE Copper Water Coil & Standard Air Coil w/Extended Range InsulationM Cupro-Nickel Water Coil & E-Coated Air Coil w/Extended Range InsulationF Cupro-Nickel Coil & Standard Air Coil w/Extended Range Insulation

Water Circuit Options 13

Piping Connections 14 R Right piping

L Left pipingV Left piping w/Stainless Steel Drain PanW Right piping w/Stainless Steel Drain Pan

Standard 15 S Standard

Option Sweat FPT MPTNone S F MMotorized Water Valve A G NAuto Flow Regulator - 2.25 GPM/Ton B H PAuto Flow Regulator - 3.0 GPM/Ton C J QMotorized Water Valve & Auto Flow Regulator - 2.25 GPM/Ton D K RMotorized Water Valve & Auto Flow Regulator - 3.0 GPM/Ton E L TSecondary Circulation Pump U V W


Page ______ of ______LC386 - 8

Performance Data – ASHRAE/AHRI/ISO 13256-1

Model

Water Loop Heat Pump Ground Water Heat Pump Ground Loop Heat Pump

Cooling 86°F Heating 68°F Cooling 59°F Heating 50°F Cooling 77°F Heating 32°F

CapacityBtuh

EERBtuh/W

CapacityBtuh COP Capacity

BtuhEER

Btuh/WCapacity

Btuh COP CapacityBtuh

EERBtuh/W

CapacityBtuh COP

TRC09 8,600 13.3 11,400 4.6 9,200 18.6 9,500 4.0 8,800 14.9 7,300 3.3

TRC12 11,300 12.8 14,100 4.5 12,500 18.7 11,800 3.9 11,800 14.5 9,300 3.3

TRC15 13,700 12.8 17,500 5.1 15,700 19.4 14,600 4.0 14,500 14.7 11,400 3.3

TRC18 15,600 12.2 20,100 4.5 17,200 17.9 16,500 3.9 16,100 13.8 13,200 3.3Cooling capacities based upon 80.6°F DB, 66.2°F WB entering air temperatureHeating capacities based upon 68°F DB, 59°F WB entering air temperatureAll air flow is rated on high speed, Units factory shipped on medium and low motor taps.All ratings based upon operation at lower voltage of dual voltage rated models

ASHRAE/AHRI/ISO 13256-1. English (I-P) Units

Model

Water Loop Heat Pump Ground Water Heat Pump Ground Loop Heat Pump

Cooling 30°C Heating 20°C Cooling 15°C Heating 10°C Cooling 25°C Heating 0°C

CapacitykW

EERW/W

CapacitykW COP Capacity

kWEERW/W

CapacitykW COP Capacity

kWEERW/W

CapacitykW COP

TRC09 2.52 3.9 3.34 4.6 2.70 5.5 2.78 4.0 2.58 4.4 2.14 3.3

TRC12 3.31 3.8 4.13 4.5 3.66 5.5 3.46 3.9 3.46 4.3 2.73 3.3

TRC15 4.02 3.8 5.13 5.1 4.60 5.7 4.28 4.0 4.25 4.3 3.34 3.3

TRC18 4.57 3.6 5.89 4.5 5.04 5.3 4.84 3.9 4.72 4.0 3.87 3.3Cooling capacities based upon 27°C DB, 19°C WB entering air temperatureHeating capacities based upon 20°C DB, 15°C WB entering air temperatureAll air flow is rated on high speed, Units factory shipped on medium and low motor taps.All ratings based upon operation at lower voltage of dual voltage rated models

ASHRAE/AHRI/ISO 13256-1. Metric (S-I) Units


Page ______ of ______LC386 - 9

Performance Data – Selection Notes

For operation in the shaded area when water is used in lieu of an antifreeze solution, the LWT (Leaving Water Temperature) must be calculated. Flow must be maintained to a level such that the LWT is maintained above 42°F [5.6°C] when the JW3 jumper is not clipped (see example below). Otherwise, appropriate levels of a proper antifreeze solution should be used in systems with leaving water temperatures of 42ºF [5.6°C] or below and the JW3 jumper should be clipped. This is due to the potential of the refrigerant temperature being as low as 32°F [0°C] with 40°F [4.4°C] LWT, which may lead to a nuisance cutout due to the activation of the Low Temperature Protection. JW3 should never be clipped for standard range equipment or systems without antifreeze.

Example:

At 50°F EWT (Entering Water Temperature) and 1.5 gpm/ton, a 3 ton unit has a HE of 22,500 Btuh. To calculate LWT, rearrange the formula for HE as follows:

HE = TD x GPM x 500, where HE = Heat of Extraction (Btuh); TD = temperature difference (EWT - LWT) and GPM = U.S. Gallons per Minute.

TD = HE / (GPM x 500)

TD = 22,500 / (4.5 x 500)

TD = 10°F

LWT = EWT - TD

LWT = 50 - 10 = 40°F

In this example, a higher flow rate will be required for EWTs at or below 50°F without antifreeze. At 2 gpm/ton, the calculation above results in a TD of 7.5. LWT = 50 - 7.5 = 42.5°F, which is above 42°F EWT, and is acceptable for this application.

EWT°F GPM

WPD* Cooling - EAT 80/67°F Heating - EAT 70°F

PSI FT TC SC Sens/Tot Ratio kW HR EER HC kW HE LAT COP

20 1.9 3.7 8.5 Operation Not Recommended 5.5 0.50 3.8 91.0 3.22

30

1.0 1.4 3.2 9.7 6.9 0.71 0.36 10.9 26.7 6.0 0.51 4.3 93.1 3.44

1.4 2.2 5.1 9.8 6.9 0.70 0.33 10.9 29.9 6.3 0.52 4.5 94.1 3.55

1.9 3.3 7.6 9.9 6.9 0.70 0.31 10.9 31.7 6.4 0.52 4.7 94.8 3.62

40

1.0 1.0 2.3 9.4 6.8 0.72 0.41 10.8 22.9 6.9 0.53 5.1 96.5 3.79

1.4 1.5 3.5 9.6 6.9 0.71 0.37 10.9 25.8 7.2 0.54 5.4 97.9 3.91

1.9 2.1 4.9 9.7 6.9 0.71 0.36 10.9 27.4 7.4 0.55 5.6 98.6 3.97

50

1.0 0.9 2.1 9.0 6.7 0.74 0.46 10.6 19.6 7.8 0.56 5.9 100.0 4.10

1.4 1.4 3.2 9.3 6.8 0.73 0.42 10.8 22.1 8.2 0.57 6.3 101.6 4.23

1.9 2.0 4.6 9.5 6.8 0.72 0.40 10.8 23.4 8.4 0.57 6.5 102.4 4.30

60

1.0 0.8 1.8 8.6 6.5 0.76 0.52 10.4 16.6 8.7 0.58 6.7 103.6 4.39

1.4 1.3 3.0 8.9 6.6 0.74 0.48 10.5 18.8 9.2 0.59 7.2 105.4 4.53

1.9 1.9 4.4 9.1 6.7 0.74 0.46 10.6 20.0 9.4 0.60 7.4 106.3 4.61

70

1.0 0.7 1.6 8.1 6.3 0.78 0.58 10.1 14.0 9.6 0.61 7.6 107.1 4.67

1.4 1.2 2.8 8.5 6.5 0.76 0.53 10.3 15.9 10.2 0.62 8.1 109.1 4.82

1.9 1.8 4.2 8.6 6.5 0.76 0.51 10.4 16.9 10.5 0.63 8.3 110.2 4.90

80

1.0 0.7 1.6 7.6 6.1 0.79 0.65 9.8 11.8 10.6 0.63 8.4 110.7 4.93

1.4 1.1 2.5 8.0 6.2 0.78 0.60 10.0 13.3 11.1 0.64 9.0 112.9 5.10

1.9 1.6 3.7 8.1 6.3 0.78 0.57 10.1 14.2 11.5 0.65 9.3 114.1 5.19

85

1.0 0.6 1.4 7.4 5.9 0.80 0.68 9.7 10.8 11.0 0.64 8.9 112.5 5.06

1.4 1.0 2.3 7.7 6.1 0.79 0.63 9.9 12.2 11.6 0.65 9.4 114.8 5.24

1.9 1.5 3.5 7.9 6.2 0.78 0.61 10.0 13.0 12.0 0.66 9.7 116.1 5.33

90

1.0 0.6 1.4 7.2 5.8 0.81 0.72 9.6 9.9 11.5 0.65 9.3 114.2 5.19

1.4 1.0 2.3 7.5 6.0 0.80 0.67 9.8 11.1 12.1 0.66 9.9 116.7 5.38

1.9 1.4 3.2 7.6 6.1 0.79 0.64 9.8 11.9 12.5 0.67 10.2 118.0 5.48

100

1.0 0.5 1.2 6.7 5.5 0.81 0.81 9.5 8.3

Operation Not Recommended

1.4 0.9 2.1 7.0 5.7 0.81 0.75 9.6 9.3

1.9 1.3 3.0 7.2 5.8 0.81 0.72 9.6 9.9

110

1.0 0.5 1.2 6.4 5.2 0.81 0.91 9.5 7.0

1.4 0.9 2.1 6.6 5.4 0.81 0.84 9.5 7.8

1.9 1.3 3.0 6.7 5.5 0.81 0.81 9.5 8.3

Interpolation is permissible; extrapolation is not.All entering air conditions are 80°F DB and 67°F WB in cooling, and 70°F DB in heating. ARI/ISO certified conditions are 80.6°F DB and 66.2°F WB in cooling and 68°F DB in heating. Table does not reflect fan or pump power corrections for ARI/ISO conditions.All performance is based upon the lower voltage of dual voltage rated units.Operation below 40°F EWT is based upon a 15% antifreeze solution. Operation below 60°F EWT requires optional insulated water/refrigerant circuit (standard on residential models).See performance correction tables for operating conditions other than those listed above.See Performance Data Selection Notes for operation in shaded areas.


Page ______ of ______LC386 - 10

Performance Data – TRC09

350 CFM Nominal (Rated) Airflow

EWT°F GPM


PSI FT TC SCSens/

Tot Ratio

kW HR EER HC kW HE LAT COP

20 2.2 5.0 11.6 Operation not recommended 6.3 0.67 4.0 86.6 2.72

301.1 1.6 3.7 9.2 6.7 0.73 0.44 10.7 20.6 6.9 0.69 4.6 88.2 2.94

1.6 2.6 6.0 8.9 6.6 0.74 0.43 10.4 20.7 7.2 0.69 4.8 89.0 3.04

2.2 4.5 10.4 8.8 6.5 0.74 0.43 10.2 20.6 7.3 0.69 5.0 89.4 3.11

401.1 1.4 3.2 9.4 6.9 0.73 0.47 11.1 19.9 7.9 0.70 5.5 90.9 3.29

1.6 2.3 5.3 9.3 6.8 0.73 0.45 10.9 20.5 8.3 0.71 5.9 91.8 3.41

2.2 4.2 9.7 9.2 6.7 0.73 0.45 10.7 20.6 8.5 0.71 6.1 92.4 3.48

501.1 1.2 2.8 9.5 7.0 0.74 0.51 11.3 18.5 8.9 0.72 6.5 93.7 3.63

1.6 2.2 5.1 9.5 6.9 0.73 0.49 11.1 19.5 9.3 0.73 6.9 94.7 3.76

2.2 3.8 8.8 9.4 6.9 0.73 0.47 11.1 19.9 9.6 0.73 7.1 95.4 3.84

601.1 1.1 2.5 9.4 7.1 0.76 0.56 11.3 16.7 10.0 0.74 7.5 96.4 3.95

1.6 2.1 4.9 9.5 7.0 0.74 0.53 11.3 17.9 10.4 0.75 7.9 97.6 4.08

2.2 3.7 8.5 9.5 7.0 0.74 0.51 11.2 18.6 10.7 0.75 8.1 98.3 4.16

701.1 1.0 2.3 9.0 7.1 0.79 0.62 11.2 14.5 11.0 0.76 8.4 99.0 4.23

1.6 2.0 4.6 9.3 7.1 0.77 0.58 11.3 15.9 11.4 0.77 8.8 100.2 4.36

2.2 3.5 8.1 9.4 7.1 0.76 0.56 11.3 16.7 11.7 0.77 9.1 101.0 4.43

801.1 1.0 2.3 8.5 7.0 0.82 0.69 10.9 12.3 11.9 0.78 9.2 101.4 4.47

1.6 1.9 4.4 8.8 7.1 0.80 0.65 11.1 13.7 12.3 0.79 9.6 102.6 4.58

2.2 3.2 7.4 9.0 7.1 0.79 0.62 11.2 14.5 12.6 0.80 9.9 103.4 4.64

851.1 1.0 2.2 8.1 6.9 0.84 0.73 10.6 11.1 12.3 0.79 9.6 102.5 4.56

1.6 1.9 4.4 8.5 7.0 0.82 0.68 10.9 12.5 12.7 0.80 10.0 103.6 4.66

2.2 3.1 7.2 8.8 7.0 0.80 0.66 11.0 13.3 13.0 0.81 10.2 104.3 4.71

901.1 0.9 2.1 7.8 6.7 0.87 0.77 10.4 10.1 12.7 0.80 10.0 103.5 4.66

1.6 1.9 4.4 8.2 6.9 0.84 0.72 10.7 11.4 13.1 0.81 10.3 104.6 4.74

2.2 3.0 6.9 8.5 7.0 0.82 0.69 10.9 12.2 13.3 0.82 10.5 105.2 4.77

1001.1 0.9 2.1 6.9 6.3 0.91 0.86 9.8 7.9

Operation not recommended

1.6 1.8 4.2 7.4 6.6 0.89 0.81 10.2 9.1

2.2 2.9 6.7 7.7 6.7 0.87 0.78 10.4 9.9

1101.1 0.9 2.1 5.8 5.6 0.97 0.96 9.1 6.0

1.6 1.8 4.2 6.4 6.0 0.94 0.91 9.5 7.0

2.2 2.9 6.7 6.7 6.2 0.92 0.87 9.7 7.7

1201.1 0.9 2.1 4.5 4.6 1.00 1.07 8.2 4.2

1.6 1.8 4.2 5.1 5.1 1.00 1.02 8.6 5.0

2.2 2.8 6.5 5.5 5.4 0.98 0.98 8.9 5.6Interpolation is permissible; extrapolation is not.All entering air conditions are 80°F DB and 67°F WB in cooling, and 70°F DB in heating. AHRI/ISO certified conditions are 80.6°F DB and 66.2°F WB in cooling and 68°F DB in heating. Table does not reflect fan or pump power corrections for AHRI/ISO conditions.All performance is based upon the lower voltage of dual voltage rated units.Performance stated is at the rated power supply; performance may vary as the power supply varies from the rated.Operation below 40°F EWT is based upon a 15% methanol antifreeze solution. Operation below 60°F EWT requires optional insulated water/refrigerant circuit.See performance correction tables for operating conditions other than those listed above.See Performance Data Selection Notes for operation in the shaded areas.

Performance capacities shown in thousands of Btuh*WPD Adder for Motorized Valve,

TRC09(Cv = 4.9,

MOPD = 150 psi)

GPMWPD AdderPSI FT

1.1 0.3 0.6

1.6 0.6 1.3

2.2 1.2 2.7


Page ______ of ______LC386 - 11


400 CFM Nominal (Rated) AirflowPerformance capacities shown in thousands of Btuh

EWT°F GPM


PSI FT TC SCSens/

Tot Ratio



301.5 2.1 4.9 12.6 8.2 0.65 0.56 14.5 22.4 8.1 0.81 5.4 86.7 2.96

2.3 4.5 10.4 12.4 8.0 0.65 0.53 14.2 23.3 8.5 0.81 5.7 87.5 3.06

3.0 6.8 15.7 12.3 8.0 0.65 0.52 14.0 23.6 8.7 0.82 5.9 87.9 3.12

401.5 2.0 4.6 12.7 8.4 0.67 0.61 14.7 20.7 9.4 0.83 6.7 89.4 3.35

2.3 4.2 9.7 12.6 8.2 0.65 0.58 14.6 21.9 9.9 0.83 7.1 90.4 3.48

3.0 6.1 14.1 12.6 8.2 0.65 0.56 14.5 22.4 10.2 0.84 7.3 90.9 3.56

501.5 1.8 4.2 12.5 8.7 0.70 0.67 14.8 18.7 10.8 0.85 8.0 92.3 3.74

2.3 3.8 8.8 12.6 8.5 0.68 0.63 14.8 20.0 11.4 0.86 8.5 93.5 3.91

3.0 5.8 13.4 12.7 8.4 0.67 0.61 14.7 20.7 11.7 0.86 8.8 94.1 4.00

601.5 1.7 3.9 12.1 9.0 0.74 0.73 14.6 16.6 12.2 0.87 9.3 95.1 4.14

2.3 3.7 8.5 12.4 8.8 0.71 0.69 14.7 17.9 12.9 0.87 9.9 96.5 4.32

3.0 5.2 12.0 12.5 8.7 0.70 0.67 14.8 18.6 13.2 0.88 10.2 97.2 4.41

701.5 1.5 3.5 11.6 9.2 0.79 0.80 14.4 14.5 13.6 0.88 10.6 97.9 4.50

2.3 3.5 8.1 12.0 9.1 0.76 0.76 14.5 15.8 14.3 0.89 11.2 99.4 4.69

3.0 4.9 11.3 12.1 9.0 0.74 0.73 14.6 16.5 14.6 0.90 11.6 100.1 4.79

801.5 1.4 3.2 11.0 9.2 0.83 0.89 14.1 12.5 14.8 0.90 11.8 100.5 4.84

2.3 3.2 7.4 11.4 9.2 0.81 0.83 14.3 13.7 15.5 0.91 12.4 101.9 5.01

3.0 4.8 11.1 11.6 9.2 0.79 0.81 14.4 14.4 15.8 0.91 12.7 102.6 5.10

851.5 1.4 3.1 10.7 9.1 0.85 0.93 13.9 11.5 15.4 0.90 12.3 101.6 4.98

2.3 3.1 7.2 11.1 9.2 0.83 0.88 14.1 12.7 16.0 0.91 12.9 102.9 5.13

3.0 4.7 10.7 11.3 9.2 0.81 0.85 14.2 13.4 16.3 0.92 13.1 103.5 5.20

901.5 1.3 3.0 10.4 9.1 0.87 0.98 13.7 10.6 15.9 0.91 12.8 102.7 5.11

2.3 3.0 6.9 10.8 9.2 0.85 0.92 13.9 11.7 16.5 0.92 13.3 103.9 5.25

3.0 4.5 10.4 11.0 9.2 0.84 0.89 14.1 12.3 16.7 0.92 13.6 104.4 5.31

1001.5 1.3 3.0 9.7 8.7 0.90 1.08 13.4 9.0


2.3 2.9 6.7 10.1 9.0 0.88 1.02 13.6 9.9

3.0 4.3 9.9 10.3 9.0 0.88 0.99 13.7 10.5

1101.5 1.2 2.8 9.0 8.2 0.91 1.20 13.1 7.5

2.3 2.9 6.7 9.4 8.5 0.90 1.13 13.3 8.4

3.0 4.2 9.7 9.6 8.7 0.90 1.09 13.4 8.8

1201.5 1.2 2.8 8.4 7.5 0.89 1.33 12.9 6.3

2.3 2.8 6.5 8.7 7.9 0.91 1.25 13.0 7.0


*WPD Adder for Motorized Valve,

TRC12(Cv = 4.9,

MOPD = 150 psi)

GPMWPD AdderPSI FT

1.5 0.5 1.02.3 1.2 2.73.0 2.2 5.0


Page ______ of ______LC386 - 12



EWT°F GPM


PSI FT TC SCSens/

Tot Ratio



301.9 1.5 3.5 16.9 11.0 0.65 0.62 19.0 27.1 10.0 0.94 6.8 87.8 3.11

2.8 3.0 6.9 16.5 10.4 0.63 0.58 18.5 28.6 10.5 0.95 7.2 88.6 3.22

3.7 4.7 10.9 16.3 10.1 0.62 0.56 18.2 29.2 10.7 0.96 7.5 89.1 3.28

401.9 1.2 2.8 16.9 11.4 0.67 0.70 19.3 24.1 11.7 0.98 8.4 90.8 3.51

2.8 2.6 6.0 16.9 11.2 0.65 0.65 19.1 26.2 12.3 0.99 8.9 91.9 3.64

3.7 4.3 9.9 16.9 11.0 0.65 0.62 19.0 27.1 12.6 0.99 9.2 92.4 3.71

501.9 1.0 2.3 16.6 11.5 0.69 0.79 19.3 21.0 13.4 1.01 10.0 93.9 3.91

2.8 2.3 5.3 16.9 11.5 0.68 0.73 19.4 23.1 14.1 1.02 10.7 95.2 4.06

3.7 3.9 9.0 16.9 11.4 0.67 0.70 19.3 24.2 14.5 1.03 11.0 95.9 4.15

601.9 0.9 2.1 15.9 11.3 0.71 0.89 18.9 17.9 15.2 1.04 11.7 97.1 4.29

2.8 2.1 4.9 16.4 11.4 0.70 0.82 19.2 19.9 16.0 1.05 12.4 98.5 4.46

3.7 3.5 8.1 16.6 11.5 0.69 0.79 19.3 21.0 16.4 1.06 12.8 99.3 4.56

701.9 0.9 2.1 15.0 10.9 0.73 0.99 18.4 15.2 16.9 1.06 13.3 100.1 4.66

2.8 2.0 4.6 15.6 11.2 0.72 0.92 18.8 16.9 17.8 1.08 14.1 101.6 4.84

3.7 3.3 7.6 15.9 11.3 0.71 0.89 18.9 17.9 18.2 1.08 14.5 102.5 4.93

801.9 0.9 2.1 14.0 10.5 0.75 1.10 17.8 12.7 18.5 1.09 14.8 103.0 4.99

2.8 1.8 4.2 14.6 10.8 0.74 1.03 18.2 14.2 19.4 1.10 15.6 104.5 5.17

3.7 3.1 7.2 15.0 10.9 0.73 1.00 18.4 15.0 19.8 1.10 16.1 105.3 5.26

851.9 0.9 2.0 13.4 10.3 0.77 1.16 17.4 11.6 19.2 1.10 15.5 104.3 5.14

2.8 1.8 4.0 14.1 10.5 0.75 1.09 17.8 13.0 20.1 1.11 16.3 105.8 5.31

3.7 3.0 6.9 14.4 10.7 0.74 1.05 18.0 13.8 20.5 1.11 16.7 106.5 5.40

901.9 0.8 1.8 12.9 10.0 0.78 1.22 17.0 10.5 20.0 1.11 16.2 105.6 5.29

2.8 1.7 3.9 13.5 10.3 0.76 1.15 17.5 11.8 20.8 1.12 17.0 107.0 5.45

3.7 2.9 6.7 13.9 10.5 0.75 1.11 17.7 12.5 21.2 1.12 17.3 107.7 5.53

1001.9 0.8 1.8 11.7 9.6 0.82 1.35 16.3 8.7


2.8 1.6 3.7 12.4 9.8 0.80 1.27 16.7 9.7

3.7 2.8 6.5 12.7 10.0 0.78 1.23 17.0 10.3

1101.9 0.8 1.8 10.6 9.2 0.87 1.48 15.7 7.2

2.8 1.6 3.7 11.2 9.4 0.84 1.40 16.0 8.0

3.7 2.7 6.2 11.5 9.5 0.83 1.37 16.2 8.4

1201.9 0.7 1.6 9.6 9.0 0.94 1.62 15.1 5.9

2.8 1.5 3.5 10.1 9.1 0.90 1.54 15.4 6.5



TRC15(Cv = 4.9,

MOPD = 150 psi)

GPMWPD AdderPSI FT

1.9 0.7 1.7

2.8 1.7 4.0

3.7 3.3 7.6


Page ______ of ______LC386 - 13



EWT°F GPM


PSI FT TC SCSens/

Tot Ratio



302.3 2.2 5.1 18.6 12.3 0.66 0.72 21.0 25.7 15.3 1.28 11.0 92.8 3.51

3.4 4.4 10.2 17.6 11.6 0.66 0.69 19.9 25.3 15.7 1.28 11.3 93.4 3.57

4.5 6.9 15.9 16.9 11.1 0.66 0.68 19.3 24.8 15.8 1.29 11.5 93.7 3.61

402.3 2.0 4.6 19.3 13.2 0.68 0.80 22.1 24.2 16.6 1.30 12.2 94.8 3.74

3.4 4.1 9.5 19.0 12.8 0.67 0.75 21.6 25.3 16.9 1.30 12.4 95.2 3.79

4.5 6.3 14.6 18.8 12.5 0.67 0.73 21.3 25.6 17.0 1.31 12.6 95.4 3.81

502.3 1.8 4.2 19.1 13.5 0.70 0.90 22.2 21.4 17.5 1.31 13.0 96.1 3.91

3.4 3.8 8.8 19.3 13.3 0.69 0.84 22.2 23.1 17.7 1.31 13.2 96.4 3.95

4.5 6.0 13.9 19.4 13.2 0.68 0.81 22.1 23.9 17.8 1.31 13.3 96.5 3.97

602.3 1.6 3.7 18.4 13.3 0.72 1.01 21.8 18.2 18.2 1.31 13.8 97.2 4.07

3.4 3.6 8.3 18.9 13.4 0.71 0.94 22.1 20.1 18.5 1.31 14.0 97.6 4.12

4.5 5.6 12.9 19.1 13.5 0.70 0.91 22.2 21.0 18.6 1.31 14.2 97.8 4.15

702.3 1.5 3.5 17.2 12.8 0.75 1.13 21.1 15.3 19.3 1.32 14.8 98.8 4.27

3.4 3.4 7.9 17.9 13.1 0.73 1.06 21.5 17.0 19.7 1.33 15.2 99.5 4.36

4.5 5.2 12.0 18.2 13.3 0.73 1.02 21.7 17.9 20.0 1.33 15.5 99.9 4.40

802.3 1.4 3.2 15.9 12.1 0.76 1.25 20.2 12.7 21.0 1.35 16.4 101.3 4.55

3.4 3.2 7.4 16.7 12.6 0.75 1.18 20.7 14.1 21.8 1.37 17.1 102.6 4.68

4.5 5.0 11.6 17.0 12.7 0.75 1.14 21.0 14.9 22.3 1.38 17.6 103.3 4.75

852.3 1.4 3.1 15.3 11.7 0.77 1.32 19.8 11.6 22.2 1.38 17.6 103.2 4.73

3.4 3.1 7.15 16.0 12.2 0.76 1.25 20.3 12.9 23.3 1.40 18.6 104.9 4.88

4.5 4.9 11.35 16.4 12.4 0.76 1.21 20.6 13.6 24.0 1.42 19.2 105.9 4.97

902.3 1.3 3.0 14.6 11.3 0.77 1.39 19.4 10.5 23.5 1.40 18.7 105.1 4.91

3.4 3.0 6.9 15.3 11.8 0.77 1.32 19.8 11.6 24.9 1.43 20.0 107.2 5.08

4.5 4.8 11.1 15.7 12.0 0.76 1.28 20.1 12.3 25.7 1.45 20.8 108.4 5.18

1002.3 1.3 3.0 13.5 10.5 0.78 1.53 18.8 8.8


3.4 2.9 6.7 14.1 10.9 0.78 1.46 19.1 9.6

4.5 4.6 10.6 14.4 11.1 0.77 1.42 19.2 10.1

1102.3 1.2 2.8 12.8 9.8 0.77 1.67 18.5 7.6

3.4 2.8 6.5 13.1 10.1 0.77 1.60 18.6 8.2

4.5 4.5 10.4 13.3 10.3 0.78 1.56 18.7 8.5

1202.3 1.2 2.8 12.6 9.4 0.74 1.82 18.9 6.9

3.4 2.8 6.5 12.6 9.5 0.76 1.75 18.6 7.2



TRC18(Cv = 4.9,

MOPD = 150 psi)

GPMWPD AdderPSI FT

2.3 0.2 0.6

3.4 0.6 1.3

4.5 1.1 2.5


Page ______ of ______LC386 - 14

Performance Data – Correction Tables

Air Flow Correction TableAirflow Cooling Heating

% ofRated

TotalCapacity

SensibleCapacity Power Heat of

RejectionHeatingCapacity Power Heat of

Extraction73% 0.946 0.898 0.971 0.951 0.967 1.084 0.937

78% 0.954 0.927 0.976 0.958 0.976 1.062 0.954

83% 0.964 0.953 0.981 0.967 0.983 1.042 0.968

89% 0.974 0.974 0.987 0.977 0.990 1.026 0.981

94% 0.987 0.990 0.993 0.988 0.995 1.012 0.991

100% 1.000 1.000 1.000 1.000 1.000 1.000 1.000

106% 1.015 1.002 1.008 1.014 1.004 0.991 1.007

111% 1.031 0.996 1.016 1.028 1.006 0.985 1.011

Entering Air Correction TablesCooling

EnteringAir WB°F

TotalCapacity

Sensible Cooling Capacity Multiplier - Entering DB °F Power Heat of

Rejection65 70 75 80 80.6 85 9060 0.926 0.632 0.820 1.004 1.182 * * * 1.003 0.931

65 0.976 0.615 0.856 1.071 1.095 1.260 * 1.000 0.979

66.2 0.990 0.555 0.807 1.030 1.055 1.224 * 1.000 0.992

67 1.000 0.507 0.765 1.000 1.017 1.188 * 1.000 1.000

70 1.039 0.620 0.865 0.893 1.076 1.252 1.001 1.032

75 1.113 0.566 0.597 0.805 1.013 1.002 1.089

* = Sensible capacity equals total capacityAHRI/ISO/ASHRAE 13256-1 uses entering air conditions of Cooling - 80.6°F DB/66.2°F WB, 1and Heating - 68°F DB/59°F WB entering air temperature

HeatingEnteringAir DB°F

HeatingCapacity Power Heat of

Extraction60 1.036 0.910 1.068

65 1.019 0.955 1.035

68 1.008 0.982 1.014

70 1.000 1.000 1.000

75 0.980 1.046 0.964

80 0.960 1.091 0.927


Page ______ of ______LC386 - 15

Antifreeze Correction Table

Table Continued on Next Page

EWT Antifreeze Type Antifreeze % Cooling Heating WPDTotal Cap Sensible Cap Watts Total Cap Watts

90

Water 0% 1 1 1 1 1 1

Ethanol

5% 0.998 0.998 1.002 0.996 0.999 1.02510% 0.996 0.996 1.003 0.991 0.997 1.04815% 0.994 0.994 1.005 0.987 0.996 1.09820% 0.991 0.991 1.006 0.982 0.994 1.14225% 0.986 0.986 1.009 0.972 0.991 1.20730% 0.981 0.981 1.012 0.962 0.988 1.26535% 0.977 0.977 1.015 0.953 0.985 1.31240% 0.972 0.972 1.018 0.943 0.982 1.3745% 0.966 0.966 1.023 0.931 0.978 1.43150% 0.959 0.959 1.027 0.918 0.974 1.494

Ethylene Glycol

5% 0.998 0.998 1.002 0.996 0.999 1.02110% 0.996 0.996 1.003 0.991 0.997 1.0415% 0.994 0.994 1.004 0.987 0.996 1.07920% 0.991 0.991 1.005 0.982 0.995 1.11425% 0.988 0.988 1.008 0.976 0.993 1.14630% 0.985 0.985 1.01 0.969 0.99 1.17535% 0.982 0.982 1.012 0.963 0.988 1.20840% 0.979 0.979 1.014 0.956 0.986 1.24345% 0.976 0.976 1.016 0.95 0.984 1.27850% 0.972 0.972 1.018 0.943 0.982 1.314

Methanol

5% 0.997 0.997 1.002 0.993 0.998 1.03910% 0.993 0.993 1.004 0.986 0.996 1.07515% 0.99 0.99 1.007 0.979 0.994 1.11620% 0.986 0.986 1.009 0.972 0.991 1.15425% 0.982 0.982 1.012 0.964 0.989 1.18930% 0.978 0.978 1.014 0.955 0.986 1.22135% 0.974 0.974 1.017 0.947 0.984 1.26740% 0.97 0.97 1.02 0.939 0.981 1.3145% 0.966 0.966 1.023 0.93 0.978 1.35350% 0.961 0.961 1.026 0.92 0.975 1.398

Propylene Glycol

5% 0.995 0.995 1.003 0.99 0.997 1.06510% 0.99 0.99 1.006 0.98 0.994 1.11915% 0.986 0.986 1.009 0.971 0.991 1.15220% 0.981 0.981 1.012 0.962 0.988 1.18225% 0.978 0.978 1.014 0.956 0.986 1.22730% 0.975 0.975 1.016 0.95 0.984 1.26735% 0.972 0.972 1.018 0.944 0.982 1.31240% 0.969 0.969 1.02 0.938 0.98 1.35645% 0.965 0.965 1.023 0.929 0.977 1.40250% 0.96 0.96 1.026 0.919 0.974 1.45


Page ______ of ______LC386 - 16

Antifreeze Correction Table

Table Continued from Previous Page

EWT Antifreeze Type Antifreeze % Cooling Heating WPDTotal Cap Sensible Cap Watts Total Cap Watts

30

Water 0% 1 1 1 1 1 1

Ethanol

5% 0.991 0.991 1.006 0.981 0.994 1.1410% 0.981 0.981 1.012 0.961 0.988 1.24215% 0.973 0.973 1.018 0.944 0.983 1.29520% 0.964 0.964 1.024 0.927 0.977 1.34325% 0.959 0.959 1.028 0.917 0.974 1.36330% 0.954 0.954 1.031 0.907 0.97 1.38335% 0.949 0.949 1.035 0.897 0.967 1.46840% 0.944 0.944 1.038 0.887 0.964 1.52345% 0.94 0.94 1.041 0.88 0.962 1.5850% 0.936 0.936 1.043 0.872 0.959 1.639

Ethylene Glycol

5% 0.997 0.997 1.002 0.993 0.998 1.0410% 0.993 0.993 1.004 0.986 0.996 1.07515% 0.99 0.99 1.006 0.98 0.994 1.12220% 0.987 0.987 1.008 0.973 0.992 1.16325% 0.983 0.983 1.011 0.966 0.99 1.19530% 0.979 0.979 1.013 0.958 0.987 1.22535% 0.976 0.976 1.016 0.951 0.985 1.27940% 0.972 0.972 1.018 0.943 0.982 1.32445% 0.969 0.969 1.021 0.937 0.98 1.37150% 0.966 0.966 1.023 0.93 0.978 1.419

Methanol

5% 0.995 0.995 1.004 0.989 0.997 1.06910% 0.989 0.989 1.007 0.978 0.993 1.12715% 0.984 0.984 1.011 0.968 0.99 1.16420% 0.979 0.979 1.014 0.957 0.986 1.19725% 0.975 0.975 1.017 0.949 0.984 1.21630% 0.971 0.971 1.019 0.941 0.981 1.23535% 0.967 0.967 1.022 0.933 0.979 1.28640% 0.963 0.963 1.025 0.924 0.976 1.32345% 0.959 0.959 1.028 0.917 0.974 1.3650% 0.955 0.955 1.03 0.91 0.971 1.399

Propylene Glycol

5% 0.995 0.995 1.004 0.989 0.997 1.07110% 0.989 0.989 1.007 0.978 0.993 1.1315% 0.985 0.985 1.01 0.968 0.99 1.20620% 0.98 0.98 1.013 0.958 0.987 1.2725% 0.974 0.974 1.017 0.947 0.983 1.35930% 0.968 0.968 1.021 0.935 0.979 1.43335% 0.963 0.963 1.025 0.924 0.976 1.52240% 0.957 0.957 1.029 0.913 0.972 1.61445% 0.949 0.949 1.034 0.898 0.967 1.71250% 0.941 0.941 1.039 0.882 0.962 1.816


Page ______ of ______LC386 - 17

Blower Performance & Electrical Data

Blower Performance

Model Rated CFM

SCFM

Low Speed MediumSpeed

High Speed

TRC09 350 270 310 350

TRC12 450 290 360 450

TRC15 520 360 440 520

TRC18 620 400 500 620Fan speed is user selectableAll airflow is rated at lowest Voltage if unit is dual Voltage rated, i.e. 208V for 208-230V unitsAll units AHRI/ISO/ASHRAE 13256-1 rated on high fan speedAll units are designed and rated for zero external static pressure (non-ducted) application

Model VoltageCode Voltage Min/Max

VoltageCompressor Fan

Motor FLA

PumpOption

FLA

Total Unit FLA

Min Circuit Amps

Max Fuse AmpsRLA LRA

TRC09

A 115/60/1 104-126 8.0 50.0 0.6N/A 8.60 10.60 15

1.0 9.60 11.60 15

G 208-230/60/1 197-254 3.7 22.0 0.5N/A 4.20 5.13 15

0.8 5.00 5.93 15

E 265/60/1 239-292 3.5 22.0 0.4N/A 3.90 4.78 15

0.7 4.60 5.48 15

TRC12

A 115/60/1 104-126 9.5 50.0 1.0N/A 10.50 12.88 20

1.4 11.90 14.28 20

G 208-230/60/1 197-254 4.7 25.0 0.6N/A 5.30 6.48 15

1.07 6.37 7.55 15

E 265/60/1 239-292 4.2 22.0 0.4N/A 4.60 5.65 15

1.3 5.90 6.95 15

TRC15G 208-230/60/1 197-254 5.6 29.0 0.7

N/A 6.30 7.70 15

1.07 7.37 8.77 15

E 265/60/1 239-292 5.0 28.0 0.6N/A 5.60 6.85 15

1.3 6.90 8.15 15

TRC18G 208-230/60/1 197-254 6.6 33.0 0.7

N/A 7.30 8.95 15

1.07 8.37 10.02 15

E 265/60/1 239-292 5.6 28.0 0.6N/A 6.20 7.60 15

1.3 7.50 8.90 15

Electrical Data


Page ______ of ______LC386 - 18

Physical Data

Model 09 12 15 18Compressor (1 Each) Rotary

Factory Charge HFC-410A (oz) [kg] 28 [0.794] 29 [0.822] 33 [0.907] 39 [1.105]

Blower WheelBlower Wheel Size (dia x w) - (in) [mm] - Qty 2 5.25 x 6.25 [133 x 159]

Water Connection SizeO.D. Sweat (in) [mm] 1/2 [12.7] 3/4 [19.1]

Optional FPT Fittings (in) 1/2 3/4

Optional MPT Fittings (in) 1/2 3/4

Coax VolumeVolume US Gal[Liters]

.09[.34]

.09[.34]

.23[.87]

.26[.98]

Condensate Connection SizeI.D. Vinyl Hose (In) [mm] 5/8 [15.9]

Air Coil Size

Dimensions (h x w) - (in) [mm] 8 x 26[203 x 660]

10 x 26 [254 x 660]

10 x 32[254 x 812]

Filter SizeBottom Return (in) [mm] 1 - 10 x 30 x 1 [254 x 762 x 25] 1 - 10 x 36 x 1 [254 x 914 x 25]

Front Return (In) [mm] 1 - 7 x 29.5 x 1/8 [178 x 749 x 3.2] 1 - 7 x 35.5 x 1/8 [178 x 902 x 3.2]

Unit SizeBottom Return (Std. 5” Base) (W x H x D) - (In) [mm] 48 x 26 x 12 [1219 x 660 x 305] 54 x 26 x 12 [1372 x 660 x 305]

Front Return (No Subbase) (W x H x D) - (In) [mm] 48 x 21 x 12 [1219 x 533 x 305] 54 x 21 x 12 [1372 x 533 x 305]

Unit WeightWeight - Operating, (lbs) [kg] 175 [79] 180 [82] 190 [86.2] 220 [99.8]

Weight - Packaged, (lbs) [kg] 185 [83.9] 190 [86] 200 [90.8] 232 [105.2]

All units have rubber grommet compressor mountings and TXV expansion devices.

Unit Maximum Water Working PressureOptions Max Pressure PSIG [kPa]Base Unit 500 [3,445]

Internal Secondary Pump (ISP) 145 [999]

Internal Motorized Water Valve (MWV) 300 [2,068]

Internal Auto Flow Valve 500 [3,445]

Use the lowest maximum pressure rating when multiple options are combined.Optional hoses have pressure rating of 400 PSIG (2758 (kPa)

Optional Factory Installed Auto Flow Regulator GPM [LPS]Model 2.25 GPM/Ton 3 GPM/Ton

9 2.0 [.126] 2.5 [.158]

12 2.5 [.158] 3.0 [.189]

15 3.0 [.189] 3.5 [.221]

18 3.5 [.221] 4.0 [.252]


Page ______ of ______LC386 - 19

Console Cabinet Dimensions – Sizes 09-15:Bottom Return – Left Hand Piping

30°

11.50(292)

.12(3) 4.90

(125)

3.50(89)

25.90(658)

DAMPER OPENING

40.98

A

(1041) 1.63(41)

1 1.75(298) D

0.59(15)

21.00(533)

4.90(125)

REAR VIEW

Ai

Sub-base

rInlet

DischargeAir

12.00(305)

Rev.: 10/03/08B

BOTTOM VIEW

11.0(279)

FRONT VIEW

Control Access Door

AIR INLET AREA

ACB

F

Left Hand Bottom Return

Notes:

1.50(38)

3.53(90)

1.75(44)

3.00(76)

0.75(19)

Bottom Access forPiping and Electric

(Note 2)

L.H.Rear AccessFor Piping and Electric(NOTE 2)

10.00(254)

1.00 (25)

1.00 (25)E

20.00(508)

SIDEVIEW

Filter located inside and at

Discharge Air Grille

top of air inlet area. Rotatefilter latch forward, filter rackcan be pulled forward 3” to 4”for filter access.

1. All Dimensions are in inches (mm).2. Access is reduced if optional disconnect box is selected.3. Optional autoflow regulator, motorized water valve, and disconnect box are not shown.4. Filter is 1”(25) thick fiberglass throwaway.

6.88(174)

2.12 (54)

FixedBack

WrapperRemovableCabinet

A B C D E F

Standard Unit

48.00(1219)

1.75(44.5)

33.50(851)

9.90(251)

4.50(114)

5.00(127)

Extended Unit

54.00(1372)

11.50(292)

34.50(876)

22.90(582)

10.50(267)

11.00(279)

Secondary circulation pump models will have extended unit.


Page ______ of ______LC386 - 20

Console Cabinet Dimensions – Sizes 09-15:Front Return – Left Hand Piping

°

L.H. RearAccess for Piping and

Electric (NOTE 2)

Notes:1. All Dimensions are in inches (mm).2. Access is reduced if optional disconnect box is selected.3. Optional autoflow regulator, motorized water valve, and disconnect box are not shown.4. Filter is a cleanable polypropylene mesh.

3.50(89)

21.00(533)

12.00(305)

40.98(1041)

.50 (13)

.75(19)

D1.00(25)

1.00(25)

21.00(533)

Bottom Access for Piping and Electric

(Note 2)

Fixed Back WrapperRemovable

Cabinet

11.50(292)

A

B

Left Hand Front Return

43.70(1110)

7.90(201)

11.00(279)

1.50(38)

A

C Discharge Air Grille

A B C D

Standard Unit

48.00(1219)

4.50(114)

5.00(127)

4.12(105)

ExtendedUnit

54.00(1372)

10.50(267)

11.00(279)

10.12(257)



Page ______ of ______LC386 - 21

Console Cabinet Dimensions – Sizes 09-15:Bottom Return – Right Hand Piping

30

11.50(292) 4.90

(125)

3.50(89)

25.90(658)

DAMPER OPENING

A

1.63(41)

40.98(1041)

11.75(298) D

0.59(15)

21.00(533)

4.90(125)

REAR VIEW

AirInlet

Discharge

Sub-base

RemovableCabinet

Fixed BackWrapper

Air

1.75(44)

3.00(76)

2.12 (54)


(Note 2)

1.00(25)

1.00(25)

E

12.00(305)

10.00(254)BOTTOM VIEW

FRONT VIEW

Control

Discharge AirGrille

Access Door

AIR INLET AREA

A

C

F

B

Right Hand Bottom Return

3.53

.12(3)

(90)

SIDEVIEW

Rev.: 10/03/08B

˚Filter located inside and attop of air inlet area. Rotatefilter latch forward, filter rackcan be pulled forward 3” to 4”for filter access

Notes:

R.H.Rear Access

for Pipingand Electric

(Note 2)

1. All Dimensions are in inches (mm).2. Access is reduced if optional disconnect box is selected.3. Optional autoflow regulator, motorized water valve, and disconnect box are not shown.4. Filter is 1”(25) thick fiberglass throwaway.

6.88 (174)

.75 (19)

1.50(38)

11.00(279)

A B C D E FStandard Unit

48.00(1219)

1.75(44.5)

33.50(851)

9.90(251)

4.50(114)

5.00(127)

Extended Unit

54.00(1372)

1.75(44.5)

33.72(856)

12.85(326)

10.50(267)

11.00(279)



Page ______ of ______LC386 - 22

Console Cabinet Dimensions – Sizes 09-15:Front Return – Right Hand Piping

30

3.50(89)

21.00(533)

21.00(533)

REAR VIEW

DischargeAir

1.00(25)

1.00(25)

B

12.00(305)

11.0(279)

FRONT VIEW

Control Access Door

Discharge Air Grille

A

C

43.70(1110)

Right Hand Front Return

7.90(201)

Bottom Access for Pipingand Electric

12.00(305)

BOTTOM VIEW

A

SIDEVIEW

AirInlet

Filter located behind returnair grille and requires removal ofcabinet front for access.

˚

Notes:1. All dimensions are in inches (mm).2. Access is reduced if optional disconnect box is selected3. Optional autoflow regulator, motorized water valve, and disconnect box are not shown.4. Filter is a cleanable polypropylene mesh.

.50(13)

11.50(292)

.75(19)

D

A B C D

Standard Unit

48.00(1219)

4.50(114)

5.00(127)

4.12(105)

ExtendedUnit

54.00(1372)

10.50(267)

11.00(279)

10.12(257)

40.98(1041)

1.50(38)

R.H.Rear Access


(Note 2)

RemovableCabinet

Fixed BackWrapper



Page ______ of ______LC386 - 23

Console Chassis Dimensions – Sizes 09-15:Bottom Return

Left

Hand

Con

figur

ation

(Bot

tom

Ret

urn)

Powe

r Sup

ply

Blow

er D

eck

Blow

er A

cces

s Pan

el

Com

pres

sor

Acce

ssPa

nel

Cont

rol B

ox

Note

s:Al

l Dim

ensio

ns a

re in

inch

es (m

m)

* If s

ubba

se o

ption

is se

lecte

d fo

r ins

talle

d dim

ensio

n, a

dd to

dim

ensio

n sh

own

4.90

" [12

4mm

] for

5" s

ubba

se,

or d

imen

sion

unit i

s rais

ed a

bove

floor

(4.9

0” [1

24] m

inim

um)

Optio

nal a

utof

low va

lve, m

otor

ized

wate

r valv

e an

d dis

conn

ect b

ox a

re sh

own.

Optio

n to

ord

er su

bbas

e (n

ot sh

own)

40.9

8(1

041)

0.75 (19)

0.75 (19)

*20.

50(5

21)

11.5

4(2

93)

*16.

66(4

23)

30°

0.87 (22)

Righ

t Han

d Co

nfigu

ratio

n(B

otto

m R

etur

n)*16.

66(4

23)

3.01 (76)5.

36(1

36)

Optio

nal

Mot

orize

dW

ater

Val

ve

Optio

nal

Auto

flow

Valv

e

*3.5

6(9

0)4.

25(1

08)

3.62

(92)

5.12

(130

)

Optio

nal

Powe

r Ter

min

atio

n (D

,H,K

) Box

(mou

nted

to ca

binet

not c

hass

is)Po

wer s

upply

ent

ers

Botto

m o

f Box

Optio

nal

Mot

orize

dW

ater

Val

ve

Optio

nal

Auto

flow

Valv

e

Optio

nal P

ower

Te

rmin

atio

n (D

,H,K

) Box

(mou

nted

to ca

binet

not c

hass

is)Po

wer s

upply

ent

ers

Botto

m o

f Box

Optio

nal D

isco

nnec

t (F)

Only

Box

(All C

onfig

urat

ions)

Powe

r sup

ply e

nter

sBo

ttom

of B

ox

Note

: Box

may

be

2 x 4

junc

tion

box

with

switc

h fa

cing

front

or s

ide.

4.25

(108

)

4.56

(116

)

Blow

er D

eck

Blow

er A

cces

s Pan

el

Com

pres

sor

Acce

ssPa

nel

Cont

rol B

ox

0.75 (19)

0.75 (19)

*20.

50(5

21)

40.9

8(1

040)

4.25

(108

)

30.0

0 (7

62)

30.0

0 (7

62)

Hard

Wire

Powe

r Sup

ply

0.87

(22)

11.5

4(2

93)

3.62

(92)

30°

3.01 (76)

5.36

(136

)

*3.5

6(9

0)

5.12

(130

)


Page ______ of ______LC386 - 24

Console Chassis Dimensions – Sizes 09-15:Front Return

Left

Hand

Con

figur

ation

(Fro

nt R

etur

n)

Powe

r Sup

ply

Blow

er D

eck

Com

pres

sor

Acce

ssPa

nel

Cont

rol B

ox

Note

s:Al

l Dim

ensio

ns a

re in

inch

es (m

m)

Chas

sis ca

n m

ount

dire

ctly o

n flo

orOp

tiona

l aut

oflow

valve

, mot

orize

d wa

ter v

alve

and

disco

nnec

t box

are

show

n.

40.9

8(1

040)

4.25

(108

)

0.75 (19)

0.75 (19)

20.5

0(5

21)

11.5

4(2

93)

16.6

6(4

23)

30°

0.87 (22)

Righ

t Han

d Co

nfigu

ratio

n(F

ront

Ret

urn)

Hard

Wire

Powe

r Sup

ply

Blow

er D

eck

Filte

r

Com

pres

sor

Acce

ssPa

nel

Cont

rol B

ox0.

87(2

2)

11.5

4(2

93)

3.62

(92)

16.6

6(4

23)

30°

3.01 (76)

5.36

(136

)

0.75 (19)

0.75 (19)

4.25

(108

)

20.5

0(5

21)

40.9

8(1

040)

3.01 (76)5.

36(1

36)

Rev.:

08/

12/1

4J

Optio

nal

Mot

orize

dW

ater

Val

ve

Optio

nal

Auto

flow

Valv

e

Optio

nal

Pow

er T

erm

inat

ion

(D, H

, K) B

reak

er B

ox(m

ount

ed to

cabin

etno

t cha

ssis)

Optio

nal

Mot

orize

dW

ater

Val

ve

Optio

nal

Auto

flow

Valv

e

5.12

(130

)

3.62 (92)

3.56 (90)

(mou

nted

to ca

binet

not c

hass

is)Po

wer s

upply

ent

ers

Botto

m o

f Box

Optio

nal D

isco

nnec

t (F)

Only

Box

(All C

onfig

urat

ions)

Powe

r sup

ply e

nter

sBo

ttom

of B

ox

Note

: Box

may

be

2 x 4

junc

tion

box

with

switc

h fa

cing

front

or s

ide.

4.25

(108

)

4.56

(116

)

Powe

r sup

ply e

nter

sBo

ttom

of B

ox

Filte

r

7.38

(187

)

30.0

0(7

62)

7.38

(187

)

Optio

nal

Pow

er T

erm

inat

ion

(D, H

, K) B

reak

er B

ox

Blow

er S

cree

n

Blow

er S

cree

n30

.00

(762

)

3.5

6(9

0)

5.12

(130

)


Page ______ of ______LC386 - 25

Piping Details – Sizes 09-15

Left Hand Configuration

Water InWater Out

Notes:* Dimension reduced by fitting if selected

2.72(96)

Right Hand Configuration

Water In

Water OutBlower Deck

Blower Access Panel

CompressorAccessPanel

Control Box

1.84(47)

0.75(19)

20.50(521)

40.98(1040)

Condensate

Condensate5/8" (15.9) ID

Vinyl Hose

OptionalMotorizedWater Valve

OptionalAutoflowValve

Water Connections5/8" (15.9)OD Copper,1/2" FPT or1/2" MPT

OptionalDisconnect Box

(mounted to cabinetnot chassis)

OptionalMotorized

Water Valve

OptionalAutoflow

Valve

Water Connections5/8" (15.9AA)OD Copper,1/2" FPT or1/2" MPT

Optional FusedDisconnect Box(mounted to cabinetnot chassis)Also Available in Non-Fused

Optional DisconnectOnly Box (All Configurations)

Optional FlowRegulatorOptional

MotorizedWater Valve

1.75 (44)

OutIn

Water Connections5/8Ó (15.9) ODCopper, 1/2Ó FPT, or1/2Ó MPT

2.25(57)

InOut

*11.25 (286)

2.00(51)

1.50 (38)

8.00 Min (203)

2.25(57)

5/8" (15.9) ID Vinyl Hose

8.00 Min (203)

Water Connections5/8Ó (15.9) ODCopper, 1/2Ó FPT, or 1/2Ó MPT

*11.25 (286)

1.62 (41)

2.00(51)

2.25 (57)

CAUTION!ÊÊCorrosiveÊsystemÊwaterÊrequiresÊcorrosionÊ

treatment.

� CAUTION! �CAUTION!ÊPipingÊmustÊcomplyÊwithÊallÊapplicableÊcodes.

� CAUTION! �



Water InWater Out

Notes:* Dimension reduced by fitting if selected

2.72(96)


Water In

Water OutBlower Deck

Blower Access Panel


Control Box

1.84(47)

0.75(19)

20.50(521)

40.98(1040)

Condensate


Vinyl Hose



Water Connections5/8" (15.9)OD Copper,1/2" FPT or1/2" MPT



OptionalMotorized

Water Valve

OptionalAutoflow

Valve

Water Connections5/8" (15.9AA)OD Copper,1/2" FPT or1/2" MPT


Optional DisconnectOnly Box (All Configurations)

Optional FlowRegulatorOptional

MotorizedWater Valve

1.75 (44)

OutIn

Water Connections5/8Ó (15.9) ODCopper, 1/2Ó FPT, or1/2Ó MPT

2.25(57)

InOut

*11.25 (286)

2.00(51)

1.50 (38)

8.00 Min (203)

2.25(57)


8.00 Min (203)

Water Connections5/8Ó (15.9) ODCopper, 1/2Ó FPT, or 1/2Ó MPT

*11.25 (286)

1.62 (41)

2.00(51)

2.25 (57)

CAUTION!ÊÊCorrosiveÊsystemÊwaterÊrequiresÊcorrosionÊ

treatment.

� CAUTION! �CAUTION!ÊPipingÊmustÊcomplyÊwithÊallÊapplicableÊcodes.

� CAUTION! �



Page ______ of ______LC386 - 26

Console Cabinet Dimensions – Size 18:Bottom Return – Left Hand Piping

30˚

11.50(292) 4.90

(125)

3.50(89)

25.90(658)

DAMPER OPENING

A

1.63

46.98(1193)

(41)

11.75(298) D

0.59(15)

21.00(533)

4.90(125)

REAR VIEW

AirInlet

DischargeAir

Rev.: 10/06/08B

BOTTOM VIEW

FRONT VIEW

Control Access Door

AIR INLET AREA

CA

B

F

Left Hand Bottom Return

Notes:

1.5011.00(279)

(38)

3.53(90)

1.75(44)3.00(76)

0.75(19)

10.00(254)

1.00 (25)

1.00 (25)E

SIDEVIEW

12.00(305)

Filter located inside and attop of air inlet area. Rotatefilter latch forward, filter rackcan be pulled forward 3” to 4”for filter access

1. All Dimensions are in inches (mm).2. Access is reduced if optional disconnect box is selected.3. Optional autoflow regulator, motorized water valve, and disconnect box are not shown.4. Filter is 1” (25) thick fiberglass throwaway.

6.88(174)

2.12 (54)

L.H.Rear Access


(Note 2)

Discharge AirGrille


(Note 2)

Sub-base

RemovableCabinet

.12(3)


54.00(1372)

1.75(44.5)

39.75(1010)

15.90(403)

4.50(114)

5.00(127)

Extended Unit

60.00(1524)

11.56(294)

35.75(908)

24.90(632)

10.50(267)

11.00(279)

Fixed BackWrapper


Page ______ of ______LC386 - 27

Console Cabinet Dimensions – Size 18:Front Return – Left Hand Piping

30˚

3.50(89)

21.00(533)

21.00(533)REAR VIEW

DischargeAir

12.00(305)

1.5011.00(279)

(38.1)

FRONT VIEW

Control Access Door

C

Left Hand Front Return

48.00(1219)

7.90(201)

21.00(533)

11.50(292)

BOTTOM VIEW

D

B

1.00 (25)

SIDEVIEW

AirInlet

Rev.: 10/06/08B


.75(19)

1.00 (25)

Notes:1. All Dimensions are in inches (mm).2. Access is reduced if optional disconnect box is selected.3. Optional autoflow regulator, motorized water valve, and disconnect box are not shown.4. Filter is a cleanable polypropylene mesh.

.50(13)

A B C DStandard Unit

54.00(1372)

4.50(114)

5.00(127)

4.12(105)

Extended Unit

60.00(1524)

10.50(267)

11.00(279)

10.12(257)

A

A

Fixed BackWrapper


(Note 2)

46.98(1193)

L.H.Rear Access


(Note 2)

Discharge AirGrille

RemovableCabinet



Page ______ of ______LC386 - 28

Console Cabinet Dimensions – Size 18:Bottom Return – Right Hand Piping

30˚

11.50(292) 4.90

(125)

3.50(89)

25.90(658)

DAMPER OPENING

A

1.63(41)

11.75(298) D

0.59(15)

21.00(533)

4.90(125)

REAR VIEW

AirInlet

DischargeAir

1.75(44)

3.00(76)

0.75 (19)

12.00(305)

10.00(254)BOTTOM VIEW

FRONT VIEW

Control Access Door

AIR INLET AREA

AB C

F

Right Hand Bottom Return

3.53

.12(3)

(90)

SIDEVIEW

RH RearAccess forPiping and

Electric(Note2)

Rev.: 10/06/08B

Notes:

Filter located inside and attop of air inlet area. Rotate filterlatch forward, filter rack can bepulled forward 3” to 4” for filteraccess.

1. All Dimensions are in inches (mm).

2.12 (54)

6.88 (174)

2. Access is reduced if optional disconnect box is selected.3. Optional autoflow regulator, motorized water valve, and disconnect box are not shown.4. Filter is 1” (25) thick fiberglass throwaway.

Sub-base

RemovableCabinet

Fixed BackWrapper


54.00(1372)

1.75(44.5)

39.75(1010)

15.90(403)

4.50(114)

5.00(127)

Extended Unit

60.00(1524)

1.75(44.5)

35.75(908)

14.00(356)

10.50(267)

11.00(279)


(Note 2)

Discharge AirGrille 11.00

(279)

1.00(25)

1.00(25)

ESecondary circulation pump models will have extended unit.


Page ______ of ______LC386 - 29

Console Cabinet Dimensions – Size 18:Front Return – Right Hand Piping

30˚

3.50(89)

21.00(533)

21.00(533)

REAR VIEW

DischargeAir

1.00(25)

1.00(25)

B

12.00(305)

FRONT VIEW

Control Access Door

A

C

Right Hand Front Return

48.00(1219)

7.90(201)

11.00(279)

21.00(533)

12.00(305) BOTTOM VIEW

A

Notes:

SIDEVIEW

AirInlet

Rev.: 10/07/08B


1. All Dimensions are in inches (mm).2. Access is reduced if optional disconnect box is selected.3. Optional autoflow regulator, motorized water valve, and disconnect box are not shown.4. Filter is a cleanable polypropylene mesh.

.75 (19)

D

11.50(292)

.50 (13)

A B C DStandard Unit

54.00(1372)

4.50(114)

5.00(127)

4.12(105)

Extended Unit

60.00(1524)

10.50(267)

11.00(279)

10.12(257)

Fixed BackWrapper

RemovableCabinet

1.50(38)

Bottom Access for Pipingand Electric(Note 2)

Discharge AirGrille

RH RearAccess forPiping and

Electric(Note 2) 46.98

(1193)



Page ______ of ______LC386 - 30

Console Chassis Dimensions – Size 18:Bottom Return

Blow

er D

eck

Blow

er A

cces

s Pa

nel

Com

pres

sor

Acce

ssPa

nel

Cont

rol B

ox

Note

s:Al

l Dim

ensio

ns a

re in

inch

es (m

m)

* For

inst

alle

d di

men

sion,

add

to d

imen

sion

show

n 4.

9" [1

24m

m] f

or 5

" sub

base

.O

ptio

nal a

utof

low

valve

, mot

orize

d wa

ter v

alve

and

disc

onne

ct b

ox a

re s

hown

.O

ptio

n to

ord

er s

ubba

se (n

ot s

hown

)

46.9

8(1

193)

0.75

(19)

0.75

(19)

*20.

50(5

21)

Hard

Wire

Pow

er S

uppl

y

Blow

er D

eck

Blow

er A

cces

s Pa

nel

Com

pres

sor

Acce

ssPa

nel

Cont

rol B

ox

0.75

(19)

0.75

(19)

*20.

50(5

21)

46.9

8(1

193)

Rev.:

10/

07/0

8B

Cond

ensa

te5/

8" ID

V(1

5.8m

m)in

yl Ho

se

0.87

(22)

11.5

4(2

93)

3.62

(92)

*16.

66(4

23)

30˚

3.01

(76)

(136

)

11.5

4(2

93)

*16.

66(4

23)

30˚

0.87

(22)

3.01

(76)5.

36(1

36)

Cond

ensa

te5/

8" ID

Vin

yl Ho

se

*3.5

6(9

0)

Opt

iona

lM

otor

ized

Wat

er V

alveO

ptio

nal

Auto

flow

Valv

eHa

rd W

irePo

wer

Sup

ply

Left

Hand

Con

figur

atio

n(B

otto

m R

etur

n)

Righ

t Han

d Co

nfig

urat

ion

(Bot

tom

Ret

urn)

(mou

nted

to c

abin

etno

t cha

ssis)

Opt

iona

lM

otor

ized

Wat

er V

alve

Opt

iona

lAu

toflo

wVa

lve

Powe

r sup

ply

ente

rsBo

ttom

of B

ox

Opt

iona

lM

otor

ized

Wat

er V

alve

Opt

iona

lAu

toflo

wVa

lve

(mou

nted

to c

abin

etno

t cha

ssis)

Powe

r sup

ply

ente

rsBo

ttom

of B

ox

Opt

iona

l Dis

conn

ect (

F)O

nly

Box

(All C

onfig

urat

ions

)Po

wer s

uppl

y en

ters

Botto

m o

f Box

Note

: Box

may

be

2 x

4 ju

nctio

n bo

x wi

th s

witc

h fa

cing

front

or s

ide.

4.25

(108

)

4.56

(116

)

4.25

(108

)

4.25

(108

)

3.62

(92)

5.12

(130

)

*3.5

6(9

0)

5.12

(130

)

36.0

0 (9

14)

36.0

0 (9

14)

Opt

iona

l P

ower

Ter

min

atio

n (D

, H, K

) Bre

aker

Box

Opt

iona

l P

ower

Ter

min

atio

n (D

, H, K

) Bre

aker

Box


Page ______ of ______LC386 - 31

Console Chassis Dimensions – Size 18:Front Return

Left

Hand

Con

figur

ation

(Fro

nt R

etur

n)

Powe

r Sup

ply

Blow

er D

eck

Com

pres

sor

Acce

ssPa

nel

Cont

rol B

ox

Note

s:Al

l Dim

ensio

ns a

re in

inch

es (m

m)

Chas

sis ca

n m

ount

dire

ctly o

n flo

orOp

tiona

l aut

oflow

valve

, mot

orize

d wa

ter v

alve

and

disco

nnec

t box

are

show

n.

46.9

8(1

193)

4.25

(108

)

0.75 (19)

0.75 (19)

20.5

0(5

21)

11.5

4(2

93)

16.6

6(4

23)

30°

0.87 (22)

Righ

t Han

d Co

nfigu

ratio

n(F

ront

Ret

urn)

Hard

Wire

Powe

r Sup

ply

Blow

er D

eck

Filte

r

Com

pres

sor

Acce

ssPa

nel

Cont

rol B

ox0.

87(2

2)

11.5

4(2

93)

3.62

(92)

16.6

6(4

23)

30°

3.01 (76)

5.36

(136

)

0.75 (19)

0.75 (19)

4.25

(108

)

20.5

0(5

21)

46.9

8(1

193)

3.01 (76)5.

36(1

36)

Rev.:

08/

12/1

4J

Optio

nal

Mot

orize

dW

ater

Val

ve

Optio

nal

Auto

flow

Valv

e

Optio

nal

Pow

er T

erm

inat

ion

(D, H

, K) B

reak

er B

ox(m

ount

ed to

cabin

etno

t cha

ssis)

Optio

nal

Mot

orize

dW

ater

Val

ve

Optio

nal

Auto

flow

Valv

e

5.12

(130

)

3.62 (92)

3.56 (90)

(mou

nted

to ca

binet

not c

hass

is)Po

wer s

upply

ent

ers

Botto

m o

f Box

Optio

nal D

isco

nnec

t (F)

Only

Box

(All C

onfig

urat

ions)

Powe

r sup

ply e

nter

sBo

ttom

of B

ox

Note

: Box

may

be

2 x 4

junc

tion

box

with

switc

h fa

cing

front

or s

ide.

4.25

(108

)

4.56

(116

)

Powe

r sup

ply e

nter

sBo

ttom

of B

ox

Filte

r

7.38

(187

)

36.0

0(9

14)

7.38

(187

)

Optio

nal

Pow

er T

erm

inat

ion

(D, H

, K) B

reak

er B

ox

Blow

er S

cree

n

Blow

er S

cree

n36

.00

(914

)

3.5

6(9

0)

5.12

(130

)


Page ______ of ______LC386 - 32

Piping Detail – Size 18


Blower Deck

Blower Access Panel


Control Box

Notes: * Dimension reduced by fitting if selected

* For installed dimension, add to dimension shown 2.9" [74mm] with 3" subbase and 4.9" [124mm] for 5" subbase.Optional autoflow valve, motorized water valve and disconnect box are shown.Water connection in same location regardless of connection type.

0.75(19)

20.44(52)


Rev.: 10/07/08B





OptionalMotorized

Water Valve

OptionalAutoflow

Valve

Water Connections.875 (22.2)OD Copper,3/4" IPT or3/4" EPT


Water Connections.875 (22.2mm)OD Copper,3/4" IPT or3/4" EPT

OptionalMotorized

Water Valve

OptionalAutoflow

Valve

WaterIn

WaterIn

Water Out

Blower Deck

Blower Access Panel


Control Box

8.00 Min (203)

1.75 (44)1.50(38)

1.84(47)


Vinyl Hose

Optional Auto Flow Valve

Optional MotorizedWater Valve

1.75 (44)

OutIn

Water Connections7/8” (22.2) ODCopper, 3/4” IPT, or3/4” EPT

*11.12 (282)

2.12 (54)

2.72(96)

Condensate

2.25(286)

InOut


*11.12 (282)

2.12 (54)

8.00 Min (203)

1.75 (44)

1.50(38)

WaterOut

Water Connections7/8” (22.2) ODCopper, 3/4” IPT, or 3/4” EPT


Page ______ of ______LC386 - 33

TRC Series Wiring Diagram Matrix

All current diagrams can be located online at climatemaster.com. Click ‘Commercial Professional’ (go to ‘Resources/literature/wiring diagrams’ in the upper right), use part numbers below to lookup wiring diagrams

DIP Setting for Board

ModelWiring Diagram

Part NumberElectricalV-Hz-Ph

Control

TRC09 - TRC18

96B0292N01115-60-1,

208/230-60-1, 265-60-1

CXM

ACO/MCO

96B0292N02 REM

96B0292N03 LON

96B0292N04 MPC

96B0293N01115-60-1,

208/230-60-1, 265-60-1

DXM

ACO/MCO

96B0293N02 REM

96B0293N03 LON

96B0293N04 MPC

OFF ON1

2

3

4

5

6

7

8

TRC DIGIT 8 = C,R + CXM Standard

TRC DIGIT 8 = L,N + CXM w/LON or MPC TRC DIGIT 8 = M,P + DXM w/LON or MPC

TRC DIGIT 8 = D,S + DXM Standard

S1

S1

S1

S1

S2

S2

1

2

3

4

5

OFF ON

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

1

2

3

4

5

6

7

8

1

2

3

4

5

OFF ON OFF ON

OFF ON OFF ON


Page ______ of ______LC386 - 34

Typical Wiring Diagram – Manual & Auto Change OverTRC Units with CXM Controller


Page ______ of ______LC386 - 35

Typical Wiring Diagram – Remote Mounted ThermostatTRC Units with CXM Controller


Page ______ of ______LC386 - 36

Typical Wiring Diagram – TRC Units with CXM & MPC Controller


Page ______ of ______LC386 - 37

Typical Wiring Diagram – Manual & Auto Change OverTRC Units with DXM Controller


Page ______ of ______LC386 - 38

Typical Wiring Diagram – Remote Mounted ThermostatTRC Units with DXM Controller


Page ______ of ______LC386 - 39

Tranquility® Console (TRC) Series 60HzEngineering Specifications – Page 1

General:Furnish and install ClimateMaster Tranquility® “Console” Water Source Heat Pumps, as indicated on the plans. Equipment shall be completely assembled, piped and internally wired. Capacities and characteristics as listed in the schedule and the specifications that follow.

Units shall be supplied completely factory built capable of operating over an entering water temperature range from 20° to 120°F (-6.7° to 48.9°C) as standard. Equivalent units from other manufacturers may be proposed provided approval to bid is given 10 days prior to bid closing. All equipment listed in this section must be rated and certified in accordance with Air-Conditioning, Heating and Refrigeration Institute/International Standards Organization (AHRI/ISO 13256-1). All equipment must be tested, investigated, and determined to comply with the requirements of the standards for Heating and Cooling Equipment UL-1995 for the United States and CAN/CSA-C22.2 NO.236 for Canada, by Intertek Testing Laboratories (ETL). The units shall have AHRI/ISO and ETL-US-C labels.

All units shall pass a factory acceptance test. The quality control system shall automatically perform factory acceptance test via computer. A detailed report card from the factory acceptance test shall ship with each unit. (Note: If unit fails the factory acceptance test, it shall not be allowed to ship. Unit serial number shall be recorded by factory acceptance test and furnished on report card for ease of unit warranty status.)

Basic Construction:Console units shall have one of the following air flow and piping arrangements: Front Inlet/Right-hand Piping; Front Inlet/Left-hand piping; Bottom Inlet/Right-hand piping; or Bottom Inlet/Left-hand piping as shown on the plans. If units with these arrangements are NOT used, the contractor is responsible for any extra costs incurred by other trades. If other arrangements make servicing difficult, the contractor must provide access panels and clear routes to ease service. Architect/Engineer must approve any changes in layout.

The cabinet, wall mounted back wrapper and subbase shall be constructed of heavy gauge galvanized steel with a baked polyester powder coat paint finish. Corrosion protection system shall meet the stringent 1000 hour salt spray test per ASTM B117. Unit corrosion protection must meet these stringent requirements or unit(s) will not be accepted. Color will be Polar Ice. Both sides of the steel shall be painted for added protection. Additionally, the wall mounted back wrapper shall have welded corner bracing. The easily removable cabinet enclosure allows for easy service to the chassis, piping compartment and control compartment.

All interior surfaces shall be lined with 1/4 inch (6.4 mm) thick, 2 lb/ft3 (32 kg/m3) acoustic flexible blanket type glass fiber insulation with a non-woven, anti-microbial treated mat face. Insulation placement shall be designed in a manner that will eliminate any exposed edges to prevent the introduction of glass fibers into the air stream. Standard insulation must meet NFPA Fire Hazard Classification requirements 25/50 per ASTM E84, UL 723, CAN/ULC S102-M88 and NFPA 90A requirements; air erosion and mold growth limits of UL-181; stringent fungal resistance test per ASTM-C1071 and ASTM G21; and shall meet zero level bacteria growth per ASTM G22. Unit insulation must meet these stringent requirements or unit(s) will not be accepted.

The cabinet shall have a 30º sloped top with aluminum rigid bar type discharge grille. Aluminum discharge grille shall be anodized charcoal grey in color including hinged control door. Cabinet shall have rounded edges (0.325 inch / 8.255 mm minimum radius) on all exposed corners for safety and aesthetic purposes. Units not having sloped top and rounded corners (0.325 inch/8.255 mm minimum) on front, side, top slope, and top corners shall not be accepted.

Return Air Filter shall be 1inch (25.4 mm) fiberglass disposable type media for bottom return units (units with sub-base) or 1/8 inch (3.2 mm) permanent cleanable type media for front return type units.

Option: The unit shall be provided with a keyed lock on the control access door.


Page ______ of ______LC386 - 40


Option: The unit shall be provided with a motorized outside air damper and damper assembly, factory mounted and wired.

Option: The unit shall be provided without a subbase (5 inch / 127 mm high subbase is standard).

Option: The unit shall include a front return air grille integrally stamped into Cabinet (subbase not required).

Option: Theunitshallincludeanoptionalarchitectural-stylefieldinstalledreturnairgrilletohelpconcealthe subbase return air opening (units with bottom return only).

Option: UltraQuiet package shall consist of high technology sound attenuating material that is strategically applied to the compressor and compressor compartment in addition to the standard ClimaQuiet system design, to further dampen and attenuate sound transmissions. Compressor is mounted on specially engineered sound-tested EPDM isolators.

Fan and Motor Assembly:Fan and motor assembly shall be assembled on a slide out fan deck with quick electrical disconnecting means to provide and facilitate easy field servicing. The fan motor shall be multi-speed, permanently lubricated, PSC type, with internal thermal overload protection. Units supplied without permanently lubricated motors must provide external oilers for easy service. The fan motor shall include a torsionally flexible motor mounting system or saddle mount system with resilient rings to inhibit vibration induced high noise levels associated with “hard wire belly band” motor mounting. The airflow rating of the unit shall be based on a wet coil and a clean filter in place. Ratingsbasedonadrycoiland/ornofiltershallNOTbeacceptable.

Refrigerant Circuit: All units shall contain an EarthPure® (HFC-410A) sealed refrigerant circuit including a high efficiency rotary compressor designed for heat pump operation, a thermostatic expansion valve for refrigerant metering, an enhanced corrugated aluminum lanced fin and rifled copper tube refrigerant to air heat exchanger, reversing valve, coaxial (tube in tube) refrigerant to water heat exchanger, and safety controls including a high pressure switch, low pressure switch (loss of charge), water coil low temperature sensor, and air coil low temperature sensor. Access fittings shall be factory installed on high and low pressure refrigerant lines to facilitate field service. Activation of any safety device shall prevent compressor operation via a microprocessor lockout circuit. The lockout circuit shall be reset at the thermostat or at the optional disconnect switch. Units that cannot be reset at the thermostat shall not be acceptable.

Hermetic compressors shall be internally sprung. The compressor will be mounted on specially engineered sound-tested EPDM vibration isolation grommets for maximized vibration attenuation. Compressor shall have thermal overload protection. Compressor shall be located in an insulated compartment away from air stream to minimize sound transmission.

Refrigerant to air heat exchangers shall utilize enhanced corrugated lanced aluminum fins and rifled copper tube construction rated to withstand 625 PSIG (4309 kPa) refrigerant working pressure. Refrigerant to water heat exchangers shall be of copper inner water tube and steel refrigerant outer tube design, rated to withstand 625 PSIG (4309 kPa) working refrigerant pressure and 500 PSIG (3445 kPa) working water pressure. The refrigerant to water heat exchanger shall be “electro-coated” with a low cure cathodic epoxy material a minimum of 0.4 mils thick (0.4 – 1.5 mils range) on all surfaces. The black colored coating shall provide a minimum of 1000 hours salt spray protection per ASTM B117-97 on all external steel and copper tubing. The material shall be formulated without the inclusion of any heavy metals and shall exhibit a pencil hardness of 2H (ASTM D3363-92A), crosshatch adhesion of 4B-5B (ASTM D3359-95), and impact resistance of 160 in-lbs (184 kg-cm) direct (ASTM D2794-93).


Page ______ of ______LC386 - 41


Refrigerant metering shall be accomplished by thermostatic expansion valve only. Expansion valves shall be dual port balanced type with external equalizer for optimum refrigerant metering. Units shall be designed and tested for operating ranges of entering water temperatures from 20° to 120°F (-6.7° to 48.9°C). Reversing valve shall be four-way solenoid activated refrigerant valve, which shall default to heating mode should the solenoid fail to function. If the reversing valve solenoid defaults to cooling mode, an additional low temperature thermostat must be provided to prevent over-cooling an already cold room.

Option: The unit will be supplied with cupro-nickel coaxial water to refrigerant heat exchanger.

Option: The unit will be supplied with internally factory mounted two-way water valve for variable speedpumpingrequirements.Afactory-mountedorfield-installedhighpressureswitchshallbeinstalled in the water piping to disable compressor operation in the event water pressures build due to water freezing in the piping system.

Option: Theunitwillbesuppliedwithinternallyfactorymountedautomaticwaterflowregulators.

Option: The unit will be supplied with internally mounted secondary pump for primary/secondary applications,specificallysingle-pipesystems.(Requiresextendedunit).

Option: The unit shall be supplied with extended range Insulation option, which adds closed cell insulation to internal water lines, and provides insulation on suction side refrigeration tubing including refrigerant to water heat exchanger.

Option: The refrigerant to air heat exchanger shall be coated.

Piping:Water piping shall terminate in the same location regardless of the connection and valve options.

Option: ThreadedMPTcopperfittings(sweatconnectionsarestandard).

Option: ThreadedFPTcopperfittings(sweatconnectionsarestandard).

Drain Pan:The drain pan shall be constructed of galvanized steel and have a powder coat paint application to further inhibit corrosion. This corrosion protection system shall meet the stringent 1000 hour salt spray test per ASTM B117. If plastic type material is used, it must be HDPE (High Density Polyethylene) to avoid thermal cycling shock stress failure over the lifetime of the unit. Drain pan shall be insulated. Drain outlet shall be located at pan as to allow complete and unobstructed drainage of condensate. The unit as standard will be supplied with solid-state electronic condensate overflow protection. MechanicalfloatswitcheswillNOTbeaccepted.

Option: The unit shall be supplied with stainless steel drain pan.

Electrical: Unit control shall be located under the hinged control door in the sloped top grille. Operating control shall consist of push buttons to select mode of operation “OFF”, “HEAT,” “COOL,” “AUTO”, Fan “AUTO” (fan cycles with compressor), Fan “ON” (continuous fan), Fan “LO” (low speed fan), and Fan “HI” (high speed fan). Temperature adjustment shall be accomplished via two push buttons, one labeled with an arrow up, and the other labeled with an arrow down. Control shall include an LCD display for display of temperature and setpoint. Units without an LCD display shall not be accepted.


Page ______ of ______LC386 - 42


A control box shall be located above the unit compressor compartment and shall contain operating controls as outlined in the paragraph above, 24VAC transformer, double-pole compressor relay, and solid-state controller for complete unit operation. Reversing valve and fan motor wiring shall be routed through this electronic controller. Units shall be name-plated for use with time delay fuses or HACR circuit breakers. A unit-mounted digital thermostat with a remote sensor measuring return air temperature shall control the compressor operation for heating and cooling. Field can configure digital ACO unit mounted thermostat for MCO operation, F or C temperature reading, and offset.

Option: Provisions for remote thermostat (single fan speed).

Option: Disconnect Switch, Non-Fused.

Option: Breaker.

Option: 20A power plug/cord.

Option: 20A plug/cord, receptacle, disconnect switch, non-fused.

Solid State Control System (CXM): Units shall have a solid-state control system. Units utilizing electro-mechanical control shall not be acceptable. The control system microprocessor board shall be specifically designed to protect against building electrical system noise contamination, EMI, and RFI interference. The control system shall interface with a heat pump type thermostat. The control system shall have the following features:

a. Anti-short cycle time delay on compressor operation.b. Random start on power up mode.c. Low voltage protection.d. High voltage protection.e. Unit shutdown on high or low refrigerant pressures.f. Unit shutdown on low water temperature.g. Condensate overflow electronic protection.h. Option to reset unit at thermostat or disconnect.i. Automatic intelligent reset. Unit shall automatically reset the unit 5 minutes after trip if the fault has cleared. If a fault occurs 3 times

sequentially without thermostat meeting temperature, then lockout requiring manual reset will occur.j. Ability to defeat time delays for servicing.k. Light emitting diode (LED) on circuit board to indicate high pressure, low pressure, low voltage, high voltage, low water/air

temperature cut-out, condensate overflow, and control voltage status.l. The low-pressure switch shall not be monitored for the first 120 seconds after a compressor start command to prevent nuisance

safety trips.m. 24V output to cycle a motorized water valve or other device with compressor contactor.n. Unit Performance Sentinel (UPS). The UPS warns when the heat pump is running inefficiently.o. Water coil low temperature sensing (selectable for water or anti-freeze).p. Air coil low temperature sensing.

NOTE: Units not providing the 8 safety protections of anti-short cycle, low voltage, high voltage, high refrigerant pressure, lowpressure(lossofcharge),aircoillowtemperaturecut-out,watercoillowtemperaturecut-out,andcondensateoverflowprotections will not be accepted.


Page ______ of ______LC386 - 43


Option: Enhanced Solid State Control System (DXM)This control system features two stage control of cooling and two stage control of heating modes for exacting temperature and dehumidification purposes.

This control system coupled with a multi-stage thermostat will better dehumidify room air by automatically running the heat pump’s fan at lower speed on the first stage of cooling thereby implementing low sensible heat ratio cooling. On the need for higher cooling performance the system will activate the second stage of cooling and automatically switch the fan to the higher fan speed setting. This system may be further enhanced with a humidistat. Units not having automatic low sensible heat ratio cooling will not be accepted; as an alternate a hot gas reheat coil may be provided with control system for automatic activation.

Control shall have all of the above-mentioned features of the CXM control system along with the following expanded features:

a. Removable thermostat connector.b. Night setback control.c. Random start on return from night setback.d. Minimized reversing valve operation (Unit control logic shall only switch the reversing valve when cooling is demanded for the first

time. The reversing valve shall be held in this position until the first call for heating, ensuring quiet operation and increased valve life.).e. Override temperature control with 2-hour timer for room occupant to override setback temperature at the thermostat.f. Dry contact night setback output for digital night setback thermostats.g. Ability to work with heat pump or heat/cool (Y, W) type thermostats.h. Ability to work with heat pump thermostats using O or B reversing valve control.i. Emergency shutdown contacts.j. Boilerless system heat control at low loop water temperature.k. Ability to allow up to 3 units to be controlled by one thermostat.l. Relay to operate an external damper.m. Ability to automatically change fan speed from multistage thermostat.n. Relay to start system pump.o. 75 VA control transformer. Control transformer shall have load side short circuit and overload protection via a built in circuit breaker.

Digital Night Setback with Pump Restart (DXM w/ATP32U03/04):The unit will be provided with a Digital Night Setback feature using an accessory relay on the DXM controller with an ATP32U03/04 thermostat and an external, field-provided time clock. The external time clock will initiate and terminate the night setback period. The thermostat will have a night setback override feature with a programmable override time period.

An additional accessory relay on the unit DXM controller will energize the building loop pump control for the duration of the override period. (Note:thisfeaturerequiresadditionallowvoltagewiring. ConsultApplicationDrawingsfordetails.)

Remote Service Sentinel (CXM/DXM):Solid state control system shall communicate with remote thermostat with fault indicator, to display (at the thermostat) the unit status, fault status, and specific fault condition, as well as retrieve previously stored fault that caused unit shutdown. The Remote Service Sentinel allows building maintenance personnel or service personnel to diagnose unit from the wall thermostat. The control board shall provide a signal to the thermostat fault light, indicating a lockout. Upon cycling the G (fan) input 3 times within a 60 second time period, the fault light shall display the specific code as indicated by a sequence of flashes. A detailed flashing code shall be provided at the thermostat LED to display unit status and specific fault status such as over/under voltage fault, high pressure fault, low pressure fault, low water temperature fault, condensate overflow fault, etc.Units that do not provide this remote service sentinel shall not be acceptable.


Page ______ of ______LC386 - 44


Option: Lonworks Interface SystemUnits shall have all the features listed above (either CXM or DXM) and the control board will be supplied with a LONWORKS interface board, which is LONMark certified. This will permit all units to be daisy chained via a 2-wire twisted pair shielded cable. The following points must be available at a central or remote computer location:

a. space temperature b. leaving water temperaturec. discharge air temperatured. command of space temperature setpointe. cooling statusf. heating statusg. low temperature sensor alarmh. low pressure sensor alarmi. high pressure switch alarmj. condensate sensor alarmk. hi/low voltage alarml. fan “ON/AUTO” position of space thermostat as specified abovem. unoccupied/occupied commandn. cooling commando. heating commandp. fan “ON/AUTO” commandq. fault reset commandr. itemized fault code revealing reason for specific shutdown fault (any one of 7)

This option also provides the upgraded 75VA control transformer with load side short circuit and overload protection via a built in circuit breaker.

Option: MPC (Multiple Protocol Control) Interface System Units shall have all the features listed above (either CXM or DXM) and the control board will be supplied with a Multiple Protocol interface board. Available protocols are BACnet MS/TP, Modbus, or Johnson Controls N2. The choice of protocol shall be field selectable/changeable via the use of a simple selector switch. Protocol selection shall not require any additional programming or special external hardware or software tools. This will permit all units to be daisy chain connected by a 2-wire twisted pair shielded cable. The following points must be available at a central or remote computer location:

a. space temperature b. leaving water temperaturec. discharge air temperatured. command of space temperature setpointe. cooling statusf. heating statusg. low temperature sensor alarmh. low pressure sensor alarmi. high pressure switch alarmj. condensate overflow alarmk. hi/low voltage alarml. fan “ON/AUTO” position of space thermostat as specified above


Page ______ of ______LC386 - 45


m. unoccupied/occupied commandn. cooling commando. heating commandp. fan “ON/AUTO” commandq. fault reset commandr. itemized fault code revealing reason for specific shutdown fault (any one of 7)

This option also provides the upgraded 75VA control transformer with load side short circuit and overload protection via a built in circuit breaker.

Warranty:ClimateMaster shall warranty equipment for a period of 12 months from start up or 18 months from shipping (which ever occurs first).

Option: Extended 4-year compressor warranty covers compressor for a total of 5 years.

Option: Extended 4-year refrigeration circuit warranty covers coils, reversing valve, expansion valve and compressor for a total of 5 years.

Option: Extended 4-year control board warranty covers the CXM/DXM control board for a total of 5 years.

FIELD INSTALLED OPTIONS

Hose Kits: Hoses shall be 1 foot (31 cm) long, braided stainless steel; fire rated hoses complete with adapters. Only fire rated hoses will be accepted. Note: Threaded connection piping option must be ordered for hose kit connections.

Option: 2 foot (61 cm) hose lengths instead of standard 1 foot (31 cm) length.

Valves:The following valves are available and will be shipped loose:

a. Ball valve; bronze material, standard port full flow design, FPT connections.b. Ball valve with memory stop and PT port.c. “Y” strainer with blowdown valve; bronze material, FPT connectionsd. Motorized water valve; slow acting, 24v, FPT connections.

Hose Kit Assemblies:The following assemblies ship with the valves already assembled to the hose described:

a. Supply and return hoses having ball valve with PT port.b. Supply hose having ball valve with PT port; return hose having automatic flow regulator valve with PT ports, and ball valve.c. Supply hose having “Y” strainer with blowdown valve, and ball valve with PT port; return hose having automatic flow regulator with

PT ports, and ball valve.d. Supply hose having “Y” strainer with blowdown valve, and ball valve with PT port; return hose having ball valve with PT port.


Page ______ of ______LC386 - 46


Thermostats:The thermostat shall be a ClimateMaster mechanical or electronic type thermostat as selected below with the described features:

a. Single-Stage Standard Manual Changeover (ATM11C11) Thermostat shall be a single-stage, horizontal mount, manual changeover with HEAT-OFF-COOL system switch and fan ON-AUTO

switch. Thermostat shall have a mechanical temperature setpoint indicator. Thermostat shall only require 4 wires for connection. Mercury bulb thermostats are not acceptable.

b. Single-Stage Digital Auto or Manual Changeover (ATA11U01) Thermostat shall be a single-stage, digital, auto or manual changeover with HEAT-OFF-COOL-AUTO system switch and fan ON-

AUTO switch. Thermostat shall have an LCD display with temperature and setpoint(s) in ºF or ºC. The Thermostat shall provide permanent memory of setpoint(s) without batteries. A fault LED shall be provided to display specific fault condition. Thermostat shall provide temperature display offset for custom applications.

c. Single-Stage Digital Automatic or Manual Changeover with Two-Speed Fan Control (ATA11U03) – DXM and PSC Fan required Thermostat shall be a single-stage, digital, auto or manual changeover with HEAT-OFF-COOL-AUTO system switch, fan ON-AUTO

switch, and fan LO-HI switch. Thermostat shall have an LCD display with temperature and setpoint(s) in ºF or ºC. Thermostat shall allow use of a remote temperature sensor (ASW06 or 17B0031N01), but may be operated with internal sensor via orientation of a jumper.

d. Multi-stage Digital Automatic Changeover (ATA22U01) Thermostat shall be multi-stage (2H/2C), manual or automatic changeover with HEAT-OFF-COOL-AUTO-EM HEAT system settings

and fan ON-AUTO settings. Thermostat shall have an LCD display with temperature, setpoint(s), mode, and status indication. The temperature indication shall be selectable for ºF or ºC. The thermostat shall provide permanent memory of setpoint(s) without batteries. A fault LED shall be provided to indicate specific fault condition(s). Thermostat shall provide temperature display offset for custom applications. Thermostat shall allow unit to provide better dehumidification with optional DXM controller by automatically using lower fan speed on stage 1 cooling (higher latent cooling) as main cooling mode, and automatically shifting to high-speed fan on stage 2 cooling.

e. Multi-stage Manual Changeover Programmable 5/2 Day (ATP21U01) Thermostat shall be 5 day/2 day programmable (with up to 4 setpoints per day), multi-stage ON-AUTO settings. Thermostat shall

have an LCD display with temperature, setpoint(s), mode, and status indication. The temperature indication shall be selectable for ºF or ºC. The thermostat shall provide permanent memory of setpoint(s) without batteries. Thermostat shall provide convenient override feature to temporarily change setpoint.

f. Multi-stage Automatic or Manual Changeover Programmable 7 Day (ATP32U03) Thermostat shall be 7 day programmable (with up to 4 setpoints per day), multi-stage (3H/2C), automatic or manual changeover

with HEAT-OFF-COOL-AUTO-EM HEAT system settings and fan ON-AUTO settings. Thermostat shall have a blue backlit dot matrix LCD display with temperature, setpoints, mode, and status indication. The temperature indication shall be selectable for ºF or ºC. Time display shall be selectable for 12 or 24-hour clock. Fault identification shall be provided (when used with ClimateMaster CXM or DXM controls) to simplify troubleshooting by providing specific unit fault at the thermostat with red backlit LCD during unit lockout. The thermostat shall provide permanent memory of setpoints without batteries. Thermostat shall provide heating setpoint range limit, cooling setpoint range limit, temperature display offset, keypad lockout, dead-band range setting, and inter-stage differential settings. Thermostat shall provide progressive recovery to anticipate time required to bring space temperature to the next programmed event. Thermostat shall provide an installer setup for configuring options and for setup of servicing contractor


Page ______ of ______LC386 - 47


name and contact information. Thermostat shall allow the use of an accessory remote and/or outdoor temperature sensor (AST008). Thermostat navigation shall be accomplished via five buttons (up/down/right/left/select) with menu-driven selections for ease of use and programming.

g. Multi-stage Automatic or Manual Changeover Programmable 7 Day with Humidity Control (ATP32U04) Thermostat shall be 7 day programmable (with up to 4 setpoints per day), multi-stage (3H/2C), automatic or manual changeover

with HEAT-OFF-COOL-AUTO-EM HEAT system settings and fan ON-AUTO settings. Separate dehumidification and humidification setpoints shall be configurable for discreet outputs to a dehumidification option and/or an external humidifier. Installer configuration mode shall allow thermostat dehumidification mode to operate with ClimaDry® reheat or with ECM fan dehumidification mode via settings changes. Thermostat shall have a blue backlit dot matrix LCD display with temperature, relative humidity, setpoints, mode, and status indication. The temperature indication shall be selectable for ºF or ºC. Time display shall be selectable for 12 or 24 hour clock. Fault identification shall be provided (when used with ClimateMaster CXM or DXM controls) to simplify troubleshooting by providing specific unit fault at the thermostat with red backlit LCD during unit lockout. The thermostat shall provide permanent memory of setpoints without batteries. Thermostat shall provide heating setpoint range limit, cooling setpoint range limit, temperature display offset, keypad lockout, dead-band range setting, and inter-stage differential settings. Thermostat shall provide progressive recovery to anticipate time required to bring space temperature to the next programmed event. Thermostat shall provide an installer setup for configuring options and for setup of servicing contractor name and contact information. Thermostat shall allow the use of an accessory remote and/or outdoor temperature sensor (AST008). Thermostat navigation shall be accomplished via five buttons (up/down/right/left/select) with menu-driven selections for ease of use and programming.

h. CM100 - Multi-stage Automatic or Manual Changeover digital thermostat (ATA32V01) Multi-stage (3H/2C), automatic or manual changeover with HEAT-OFF-COOL-AUTO-EM HEAT system settings and fan ONAUTO

settings. Thermostat shall have a green backlit LED display with temperature, setpoints, mode, and status indication via a green (cooling) or red(heating) LED. The temperature indication shall be selectable for ºF or ºC. Time display shall be selectable for 12 or 24 hour clock. The thermostat shall provide permanent memory of setpoints without batteries. Thermostat shall provide heating setpoint range limit, cooling setpoint range limit, temperature display offset, keypad lockout, dead-band range setting, and inter-stage differential settings. Thermostat shall provide progressive recovery to anticipate time required to bring space temperature to the next programmed event. Thermostat shall provide an installer setup for configuring. Thermostat navigation shall be accomplished via four buttons (Mode/fan/down/up) with menu-driven selections for ease of use and programming.

i. CM300 – Multi-stage, Automatic or Manual Changeover, 7-day Programmable with Wi-Fi and Humidity Control (AVB32V02C) Residential version shall be 7 day programmable with up to 4 setpoints per day. Commercial version shall be 7 day programmable

with 4 occupied/unoccupied periods per day with up to 4-hour override. Multi-stage (3H/2C), automatic or manual changeover with HEAT-OFF-COOL-AUTO-EM HEAT system settings and fan ON-AUTO settings, Wi-Fi, pre-occupancy purge fan option, night time control of display backlight, bi-color LED indicates a heating or cooling demand, keypad lock, title 24 compliant, openADR2.0b certified with Skyport web portal. Compatible with condensate overflow warning systems – lockout compressor with message on.

j. CM500 – Color Touchscreen Display, Multi-stage, Automatic or Manual Changeover, 7-day Programmable with Wi-Fi and Humidity Control (AVB32V03C)

Thermostat shall have color resistive touchscreen display with space temperature, relative humidity, setpoints, mode, status indication and local weather (if connected to Wi-Fi). Residential version shall be 7 day programmable with up to 4 setpoints per day. Commercial version shall be 7 day programmable with 4 occupied/unoccupied periods per day with up to 4-hour override. Multi-stage (3H/2C), automatic or manual changeover with HEAT-OFF-COOL-AUTO-EM HEAT system settings and fan ONAUTO settings, Wi-Fi, pre-occupancy purge fan option, customizable screen saver and background displays, indicator on display indicates a heating or cooling demand, set-point lock, title 24 compliant, openADR2.0b certified with Skyport web portal. Compatible with condensate overflow warning systems – lockout compressor with message on the display. Capable of being


Page ______ of ______LC386 - 48


monitored by 3rd party software. Compatible with AST014 Wi-Fi remote sensor. Configurator mobile app or web portal for easy setup. Separate dehumidification and humidification setpoints shall be configurable for discreet outputs to a dehumidification option and/or an external humidifier. The temperature indication shall be selectable for ºF or ºC. Time display shall be selectable for 12- or 24-hour clock. The thermostat shall provide permanent memory of setpoints without batteries. Thermostat shall provide heating setpoint range limit, cooling setpoint range limit, temperature display offset, dead-band range setting, and inter-stage differential settings. Thermostat shall provide progressive recovery to anticipate time required to bring space temperature to the next programmed event. Thermostat shall provide access to a web portal and mobile app for installer setup for configuring options. Thermostat shall have menu-driven selections for ease of use and programming.

DDC Sensors:ClimateMaster wall mounted DDC sensor to monitor room temperature and interfaces with optional interface system described above. Several types as described below:

a. Sensor only with no display (LON and MPC).b. Sensor with override (LON only).c. Sensor with setpoint adjustment and override (MPC only).d. Sensor with setpoint adjustment and override, LCD display, status/fault indication (LON and MPC).

Subbase Grille:Decorative louvered grille covers the front of subbase including the large return air opening. Order separate and field attach.

NOTICE!ThisproductspecificationdocumentisfurnishedasameanstocopyandpasteClimateMaster product information intoprojectspecification.Itisnotintendedtobeacompletelistofproductrequirements.Thisdocumentisanexcerptfromtheproduct submittal and must not be used without consulting the complete product submittal. For complete product installation and application requirements, please consult the complete product submittal. ClimateMaster is not responsible for misuse of this documentorafailuretoadequatelyreviewspecificrequirementsintheproductsubmittal.


Page ______ of ______LC386 - 49

Performance Sheet

SUBMITTAL DATA - I-P UNITS

Unit Designation:

Job Name:

Architect:

Engineer:

Contractor:

PERFORMANCE DATA

Cooling Capacity: Btuh

EER:

Heating Capacity: Btuh

COP:

Ambient Air Temp: °F

Entering Water Temp (Clg): °F

Entering Air Temp (Clg): °F

Entering Water Temp (Htg): °F

Entering Air Temp (Htg): °F

Airflow: CFM

Fan Speed or Motor/RPM/Turns:

Operating Weight: (lb)

ELECTRICAL DATA

Power Supply: Volts

Phase Hz

Minimum Circuit Ampacity:

Maximum Overcurrent Protection:

SUBMITTAL DATA - S-I UNITS

Unit Designation:

Job Name:

Architect:

Engineer:

Contractor:

PERFORMANCE DATA

Cooling Capacity: kW

EER:

Heating Capacity: kW

COP:

Ambient Air Temp: °C

Entering Water Temp (Clg): °C

Entering Air Temp (Clg): °C

Entering Water Temp (Htg): °C

Entering Air Temp (Htg): °C

Airflow: l/s

Fan Speed or Motor/RPM/Turns:

Operating Weight: (kg)

ELECTRICAL DATA

Power Supply: Volts

Phase Hz

Minimum Circuit Ampacity:

Maximum Overcurrent Protection:


Page ______ of ______LC386 - 50

Notes


Page ______ of ______LC386 - 51

Revision History

Date: Item: Action:12-14-20 Pg. 7 Updated Decoder: Piping Connections

10-2-20 All Added new thermostat options. Decoder option description correction. Various text updates.

6-3-20 Pg.32 Updated Wiring Diagram Matrix

5-26-20 Pg. 14 Updated Antifreeze Correction Table

11/1/16 Updated Document Design Updated

9/29/16 Pages 21-23, 28-30Updated discount box dimensions and corrected TRC18 dimensions

03/28/16 Page 37 Run test Engineering Specs. edit

09/21/15 Electrical Data, Physical Data, Wiring Diagram Matrix, and Wiring Diagrams

Updated

08/12/15 All Updated

08/13/14 Misc. Edits - Page 4, 16, 22, 43 and Wiring Diagrams and Engineering Specs

Updated

11/26/13 Physical Data Table Updated

11/15/13 ASHRAE/AHRI/ISO English & Metric Tables Updated

02/08/13MCO ThermostatEngineering SpecificationsAdded 2 HPWS to Safeties

RemovedUpdated

11/29/12 Console - Chassis Dimensional Data, Sizes 09-15 and 18 Updated

02/27/12 Unit Features Updated

02/20/12 Engineering Specifications Updated

12/06/11 All Added Extended Unit for I SP, Deleted Isolation Plate

11/08/11 Electrical Data TableCabinet Dimension Illustrations

Updated

08/09/11 Unit Maximum Working Water Pressure Updated to Reflect New Safeties

08/03/11 Engineering Specifications Added Digital Night Setback with Pump Restart (DXM w/ ATP32U03/04)

07/05/11 Cover Unit Photo Caption Added

06/13/11 Unit FeaturesEngineering Specifications Updated

04/07/11 Engineering Specification NOTICE Updated

02/11/11 Performance Data Selection Notes Updated

01/03/11 Format All Pages Updated

07/29/10 Cabinet Dimensions-Size 18Bottom Return-Left & Right Hand Piping

Updated Dimensions

07/26/10 Wiring Diagrams Updated

07/26/10 Compressor Mounting Information and Graphics Engineering Specifications

Updated to Reflect Spring/Grommet Change


Page ______ of ______LC386 - 52

Revision History

7300 S.W. 44th StreetOklahoma City, OK 73179

Phone: 405-745-6000climatemaster.com

06/11/10 Engineering Specs Updated

06/11/10 Format All Pages Updated

06/11/10 Wiring Diagrams New Wiring Diagrams


03/29/10 Physical Data Table Coax Volume Field Added

05/19/09 Engineering Specifications Thermostat and Electrical Sections Updated

05/19/09 Stand-Alone and Big Book Submittals Consolidated


09/22/08 Cabinet Dimensions Sizes 06-15 and 18 Updated and Verbiage Changes

08/26/08 Physical Data Table Max Working Pressure Table Added

06/12/08 Wiring Diagram Matrix ETL Information Added

05/30/07 MWV Pressure Drop Data Updated

04/19/07 Table of Contents Added Table of Contents

04/19/07 Specifications Updated Specifications with new Safety Agency

07/14/06 First published

Date post:	28-Aug-2020
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

Tranquility Console (TRC) Series - Climate Master...Jul 14, 2006 · ClimateMaster works...

Documents