Post on 23-Sep-2020
transcript
1THESE INSTRUCTIONS ARE TO BE LEFT WITH THE USER
Installation
POWER HANDSET
Accessory Pack
1540.268 & 1540.269
2
Notes
3
Introduction
The Mira power handset is an adjustable spray showerhead with four different sprayactions: start, champagne, massage and eco. If is sutable for most power showers andhigh pressure systems above 0.5 bar.
The Mira power handset is available in white or chrome.
System Applications
• Instantaneous gas heated systems
• Mains pressure systems
• Pumped systems
Additional Features
• Adjustable showerhead with four spray patterns
• Visual indicators for spray settings
• Rub-clean rubber nozzles to remove scale build-up.
4
40°
169mm
199mm
All dimensions are nominal and in millimetres
Installation
Before Installing
Before installing the handset, consider these placement tips:
1. Position the handset in a convenient position for all the family.
2. Position the handset so that the spray discharges away from the showercontrol, and down the centre line of the bath or across (rather than into) theshower cubicle opening.
Installation1. Unscrew the existing handset
from the flexible shower hose.
Note! The hose and handset mayhave water in them.
2. Screw the Mira handset into theflexible shower hose. If there isa hose washer, be careful toretain it.
Caution! Do not overtighten.
Handset
HoseWasher
FlexibleShowerHose
Dimensions
5
Operation
Spray Settings
The handset has four spray settings: Eco, Start, Champagne, and Massage.
1. Eco: Water flows from the outer setof holes at a reduced flow rate.
To select the Eco setting, turn thespray plate fully clockwise.
2. Start: Water flows from the outerset of holes.
To select the Start setting, turn thespray plate anticlockwise from thefull clockwise position until it clicksonce.
3. Champagne: Water flows from themiddle holes.
To select the Champagne setting,turn the spray plate anticlockwisefrom the full clockwise position untilit clicks twice.
4. Massage: Water flows from theinner set of holes.
To select the Massage setting, turnthe spray plate anticlockwise fromthe full clockwise position until itclicks three times.
6
Spray PlateAssembly
Maintenance
Daily Cleaning
Use your thumb or a soft cloth to wipe any limescale from the soft rubber nozzles andthe front face of the showerhead.
Full Cleaning1. Turn the adjuster ring fully
anticlockwise.
2. Unclip and remove the adjuster ring.
3. Unscrew the spray plate assemblyin an anticlockwise direction. The‘O’ seals will provide someresistance.
4. Remove the massage turbinw andthe nozzle retaining ring.
5. Clean all of the components with astiff brush.
6. If necessary, use a plastic kettledescalent to remove stubbornlimescale, following themanufacturer’s instructions.
7. If the ‘O’ seals are damaged, replacethem with new ‘O’ seals. (Spare partnumber 450.08, available fromCustomer Services. See the backpage for more information).
8. Refit the components in reverseorder. Ensure that the ‘O’ seals, themassage turbine and the nozzle ringretainer are fitted correctly.
Adjuster Ring
‘O’ Seals
Nozzle RingRetainer
Massage Turbine
7
Notes
8P4647 (L86N) © Kohler Mira Limited, September 2004
Mira ShowersKohler Mira LtdCromwell Road,Cheltenham GL52 5EP.
Mira is a registered trade mark.The company reserves the right to alterproduct specifications without notice.
www.mirashowers.com
Customer ServiceGuarantee (Accessories)Mira Showers guarantees this product against any defect ofmaterials or workmanship for one year from the date ofpurchase.
Within the guarantee period we will resolve defects, free ofcharge, by repair or replacement as we may choose.
Not covered by this guarantee:
• Damage or defects arising from incorrectinstallation, improper use or lack of maintenance,including build-up of limescale.
• Damage or defects if the product is taken apart,repaired or modified by any person not authorisedby Mira Showers or our approved agents.
Proof of Purchase will be required to support any guaranteeclaims.
This guarantee is in addition to your statutory and other legalrights.
Our Customer Services Team is comprehensively trained toprovide every assistance you may need: help and advice,spare parts or a service visit.
As part of our quality and training programme calls may berecorded or monitored.
Spare PartsWe maintain an extensive stock of spares, which can bepurchased from approved stockists or merchants (locationson request) or direct from Customer Services.
Spares direct will normally be despatched within two workingdays. Payment can be made by Visa or Mastercard at thetime of ordering. Should payment by cheque be preferred apro-forma invoice will be sent.
Note! In the interests of safety, spares requiring exposure tomains voltages can only be sent to competent persons.
ServiceOur Service Force is available to provide a quality service ata reasonable cost. You will have the assurance of a Miratrained engineer/agent, genuine Mira spares – and a 12month guarantee on the repair.
To contact usEngland, Scotland & WalesMira Showers Customer ServicesTelephone: 0870 241 08888:30 am to 5:00 pm Working days (4:30 pm Friday)8:30 am to 12.30 pm SaturdayE-mail: technical@mirashowers.comFax: 01242 282595By Post: Cromwell Road
CheltenhamGloucester GL52 5EP
Northern IrelandWm H Leech & Son LtdTelephone: 028 9044 9257 – Mon to Fri 9 am-5pmFax: 028 9044 9234 – 24 hoursPost: Maryland Industrial Estate
Ballygowan RoadMoneyreagh, Co DownBT23 6BL
Republic of IrelandModern Plant LtdTelephone: Dublin 01 4591344 – Mon to Fri 9am to 5pmFax: Dublin 01 4592329 – 24 hoursPost: Otter House
Naas RoadClondalkinDublin 22
Check out our full range of Showers Electric Showers
Digital Showers
Mixer Showers
Power Showers
Smart Showers
Shower Towers
From Top Shower Brands Mira Showers
Aqualisa Showers
Triton Showers
Gainsborough Showers
Shower Pumps can upgrade your showering experience even more Stuart Turner Shower Pumps
Salamander Shower Pumps
Grundfos Shower Pumps