االسمنتيةالحلول Made in Jordan according to
American and European
specifications
صنع في األردن حسب
مواصفات أمريكية و
:Contact Usأوروبية
Tel: (+962 6 41 66 989)
Mob: (+962 799 212 777)
E-mail: [email protected]
www.cementsolutions.info
WHO WE ARE:We are Petra Chemicals Co., producers of wide range of construction chemicals under the brand name CEMENTSOLUTIONS, our factory is located at Abu Alanda Industrial Zone, Amman, Jordan, with a production capacity up to 120 tons per day. Our products comply with the American and European standards according to certified tests, with a very competitive prices.
SCOPE OF PRODUCTS:Tile Adhesive & Grout, Concrete Repair, Non-Shrink Grouts, Surface Treatments, Bonding Agents, Flooring & Coatings, Waterproofing, decorative finishing, and many other products for special purposes.
FOR MORE INFORMATION ABOUT OUR PRODUCTS PLEASE CHECK THE DRAWING:• Which would help you better understand our products, solutions for variety of cases, application tips and
products recommendations to utilize and improve your project quality.
CONTACT US:Tel: (+962 6 41 66 989)
Mob: (+962 799 212 777)
E-mail: [email protected]
www.cementsolutions.info
CEMENT SOLUTIONS:
Exterior Paints has many system solutions depends on the location, area, weather conditions , and siteconditions.
We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for theexterior paint after the Surface Preparation is accomplished we suggest the CEMEPROOF PAINT it has beenformulated to confer long term protective and decorative properties to concrete and masonry surfaces.
Exterior Paints: For More Information Please
Click The Product Name.
Exterior Paints:
CEMEPROOF PAINT Elastomeric acrylic emulsion, waterproofing anti-carbonation and weatherproofing UV-resistant coating for exterior applications.
Product Name CEMEPROOF PAINT
Uses Weatherproofing and anti-Carbonation Paint for outdoor use.
Packaging 5 Kg or 20 Kg.
Coverage 80m2 @150 microns thickness per coat @smooth plaster.
Colors White or Light Grey (BS4800 or RAL colors are available upon request).
ApplicationApply coating by brush, roller or airless spray at a nominal rate of 5m²/liter andallow to dry, A second coat may be subsequently applied at the same rate.
Back to Exterior Paints
Roof Waterproofing:
Roof Waterproofing has many system solutions depends on the location, area, weather conditions, and siteconditions.
We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the roofwaterproofing after the Surface Preparation is accomplished we suggest 2 systems:1. Acrylic System: First step use CEMECRYL PRIMER which is liquid admixture to improve bonding, and
workability of the surface. The second and last step use CEMELASTIC which is a waterproof elastic singlecomponent coating for all types of roofs.
2. Cementitious System: First step use CEMECRYL PRIMER which is liquid admixture to improve bonding, andworkability of the surface. Then use CEMELEVEL POLYMER UW which provides a non-toxic, waterproofingand floor over lay for releveling and refurbishing cementitious based floor slabs. Last step use CEMEFLOORGLAZE which is transparent polymer sealer, gloss finish, for protection of concrete, and zero absorptionsurface.
For More Information PleaseClick The Product Name.
Roof Waterproofing:
1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties ofcement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves themechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction ofwater absorption by capillarity.
Product Name CEMECRYL PRIMER
Uses Porosity sealer and primer applied directly on the surface.
Packaging 5 L – 25 L.
Coverage 1 L Covers 4 m2 @ 100 micron thickness @ smooth surface.
Colors None.
Application
Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry andonce it has been completely absorbed in the support, depending on porosity,apply the mortar or concrete, apply next material within 10 hours afterpriming.
Next
Roof Waterproofing:
2. CEMELASTIC is an elastic acrylic coating, specially formulated for all types of roofs. It is supplied in the formof a water-based single component paint, ready to use. Once polymerized it is transformed into an UV-raysresistant and waterproofing film.
Product Name CEMELASTIC
UsesWaterproofing, flexible and resistant to sun rays and non-preamble to water forroof application.
Packaging 5 Kg or 20 Kg.
Coverage 1 Kg covers 2 m2 @ 1 mm thickness @smooth surface.
Colors White or Grey (BS4800 or RAL colors are available upon request).
ApplicationApplied by brush or roller. When using an airless spray, dilute with a sufficientbut minimum amount of water to allow the easy application of the product, 2coats recommended.
PreviousBack to Roof
Waterproofing
Roof Waterproofing:
Next
1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties ofcement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves themechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction ofwater absorption by capillarity.
Product Name CEMECRYL PRIMER
Uses Porosity sealer and primer applied directly on the surface.
Packaging 5 L – 25 L.
Coverage 1 L Covers 4 m2 @ 100 micron thickness @ smooth surface.
Colors None.
Application
Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry andonce it has been completely absorbed in the support, depending on porosity,apply the mortar or concrete, apply next material within 10 hours afterpriming.
Roof Waterproofing:
2. CEMELEVEL POLYMER UW is a self-level cementitious two-component product. Component A is a mortarbased on a special polymerized mixture, and component B is a water-based special acrylic resin. It providesa non-toxic, waterproofing and floor over lay for releveling and refurbishing cementitious based floor slabs.
Product Name CEMELEVEL POLYMER UW
UsesWaterproofing, flexible and resistant to sun rays and non-preamble to water forroof application.
Packaging (A) 20 Kg + (B) 5 L .
Coverage 1 package covers 10m2 @ 1 mm thickness @ smooth surface.
Colors Grey (Concrete Color).
ApplicationPour or pump the mixed material onto the surface spread with trowel andallow to level, and allow attaining a smooth finish, it can be diluted withCEMECRYL PRIMER for high temperature to give better workability.
Previous Next
Roof Waterproofing:
3. CEMEFLOOR GLAZE is a transparent polymer sealer, derived from methacrylate-based resins. It forms adurable, tough and flexible film with gloss finish for protection of concrete and masonry. It resistsweathering, air pollutants, alkaline agents and ultra-violet rays (UV).
Product Name CEMEFLOOR GLAZE
UsesClear acrylic developed to provide hard, glossy, Protective Sealer to beautifyand protect regular concrete surface.
Packaging 5 L or 25 L.
Coverage 1 L Covers 4 m2 @ 150 microns thickness per coat @ smooth surface.
Colors None.
Application Apply with brush, roller, or spray, 2 coats recommended.
PreviousBack to Roof
Waterproofing
Repair Materials:
Repair Materials works usually for so many factors that achieve the best repair, repair materials products haveadvantages in all factors to satisfy the project needs, such as high adhesion strength to older concrete, non-shrinkage materials, high mechanical properties and easy to use and apply after surface preparation isaccomplished.
1. CEMEBUTTY FC200 Cementitious thin fairing putty repair mortar for concrete surfaces, plaster surfaces,and fair face repair.
2. CEMEPATCH XTRA Repair mortar enhanced with fibers, special cements, additives and selected aggregates.3. SHOTCRETE F20 Repair cement mortar for buildings and large areas repair.4. CEMEPATCH 400 Structural component with a thixotropic product and shrinkage-compensated for repairs.5. CEMECRYL JOINT SEALANT Joint acrylic sealant and crack filler.6. CEMECUR 101 Concrete curing agent to prevent an excessive fast drying.7. CEMEHARD 100 Dry-Shake cement hardener powder for concrete surfaces hardening.8. CEMECLEANER Polishing, shining, and cleaning.9. CEMEFLOW G100 non-shrinkage grout for under-machinery and steel plates uses.10. CEMEBOND LATEX SBR additive and bonding agent to cement to improve mechanical properties and water
retention.
For More Information PleaseClick The Product Name.
1. CEMEBUTTY FC200 is a one part, polymer modified, cementitious thin fairing putty repair mortar forconcrete surfaces, and plaster surfaces. Needs adding water for application.
Product Name CEMEBUTTY FC200
UsesCover minor surface defects on concrete, plaster, mortar and stone masonry, It
is suitable for small repairs, and fair face concrete surfaces.
Packaging 20 Kg.
Coverage Depends on the repair size.
Colors Light Grey.
Application
Mix each 20 Kg with 4-5 L of water then apply on the prepared surface using asteel trowel. It should be worked well into the pin holes and surface blemishes.It should be allowed to set partially before final finishing with sponge or steeltrowel. Water can be sprinkled on the applied material before final trowel orsponging.
Repair Materials:
Back to Repair Materials
2. CEMEPATCH XTRA Structural repair mortar enhanced with fibers, special cements, additives and selectedaggregates. Needs adding water for application.
Product Name CEMEPATCH XTRA
UsesCover major surface defects on concrete, plaster, mortar and stone masonry, , Itis suitable for big repairs, and voids in concrete.
Packaging 25 Kg.
Coverage Depends on the repair size.
Colors Grey (Concrete Color).
Application
Mix 25 Kg with 5 L of water then apply on the repair spot using a steel trowel. Itshould be allowed to set partially before final finishing with sponge or steeltrowel. Water can be sprinkled on the applied material before final trowel orsponging.
Repair Materials:
Back to Repair Materials
3. SHOTCRETE F20 is made with accurately mass-batched blends of Portland cement, polymers, sand, courseaggregate and powdered accelerator. It has been specifically designed for applications that require fastsetting characteristics used in mining, tunneling and civil projects.
Product Name SHOTCRETE F20
UsesDry bagged shotcretes are used in a wide range of civil engineering and mining
applications, where fast drying and vertical ceiling application take place.
Packaging 25 Kg.
Coverage Depends on the surface.
Colors Grey (Concrete Color).
ApplicationMix 25 Kg with 6 L of water apply on the prepared surface using a steel trowel,or spray gun. Water can be sprinkled on the applied material before final trowelor sponging.
Repair Materials:
Back to Repair Materials
4. CEMEPATCH 400 is one-component structural repair mortar, composed of special cements, additives andselected aggregates, which provides a thixotropic product with quick-setting and shrinkage-compensated.Meets Class R4 according to European Standard EN-1504-3.
Product Name CEMEPATCH 400
UsesRestoration of structural concrete elements, recovering original shape andfunction.
Packaging 25 Kg.
Coverage Depends on the surface.
Colors Grey (Concrete Color).
ApplicationApplied on the prepared surface using a steel trowel. It should be allowed toset partially before final finishing with sponge or steel trowel. Water can besprinkled on the applied material before final trowel or sponging.
Repair Materials:
Back to Repair Materials
5. CEMECRYL JOINT SEALANT is a water-based single component acrylic paste, stops the flow of water to permanentlyrepaired concrete cracks, holes and joints, it maintains flexibility and water proofing joint sealant and providesoutstanding durability.
Product Name CEMECRYL JOINT SEALANT
UsesMaintenance of joints in concrete, concrete runway and crack repair inconcrete.
Packaging 1 Kg or 5 Kg.
Coverage Depends on the surface.
Colors Light Grey.
Application
Can be applied a manually or with gun. Use typical joint sealing practices andproper joint design of 2:1 width to depth ratio when applying. Horizontal jointsrequire a minimum of (15 mm) depth and maximum (30 mm) depth. Afterapplication the product can be smoothed with a polish.
Repair Materials:
Back to Repair Materials
6. CEMECUR 101 is a water-based milky pure acrylic resin, a curing agent that sprayed over the surface offresh concrete or mortar, provides a thin film acting as a protective barrier to prevent an excessive fastdrying.
Product Name CEMECUR 101
Uses Curing of fresh concrete and mortar.
Packaging 25 L or 200 L.
Coverage 1 L covers 4 m2.
Colors None.
Application
Can be sprayed by either manual or air-powered spray, directly over the surfaceof fresh concrete or mortar, leaving a thin and continuous film. The applicationwill be carried out in two successive coats, being sprayed when the surface hasstarted to become matt
Repair Materials:
Back to Repair Materials
7. CEMEHARD 100 is formulated with special cements, pigments, additives and aggregates designed to beapplied on fresh concrete in order to improve its abrasion resistance and provides an anti-dust finish in onesingle application.
Product Name CEMEHARD 100
Uses Harding of pavements of garages, parking, shopping malls, schools, hospitals.
Packaging 25 Kg.
Coverage 3 Kg covers 1 m2.
Colors Grey (Concrete Color) (BS4800 or RAL colors are available upon request).
ApplicationThe concrete slab should be perfectly extended, lined and leveled. Theconcrete will be designed with enough structural resistance for the requiredpurpose.
Repair Materials:
Back to Repair Materials
8. CEMECLEANER is designed for cleaning salts, grease and oil on cement and concrete surfaces. It’s specialformulation attacks and dissolves the stains helping to eliminate them.
Product Name CEMECLEANER
UsesCleaning agent for oils, animal grease, etc., on cement and concrete floors,pavements and walls.
Packaging 5 L.
Coverage Depends on the surface and the dissolves.
Colors None.
ApplicationSpill over stains and let it react for minutes then brush and once the remains ofthe stain have disappeared, wash thoroughly with clean water and allow it todry
Repair Materials:
Back to Repair Materials
9. CEMEFLOW G100 is an one-component non-shrink mortar formulated from special cements and well-graded mineral products which provides high mechanical properties and fluidity vibration resistance.
Product Name CEMEFLOW G100
Uses Base concrete of machines and grid beams.
Packaging 25 Kg.
Coverage Depends on depth and thickness.
Colors Grey (Concrete Color).
ApplicationMix with 5 L of water apply simply pouring by gravity directly from the mixingcontainer. In order to avoid cold joints and minimize the chance of airentrapment.
Repair Materials:
Back to Repair Materials
10. CEMEBOND LATEX SBR is a water-based styrene-butadiene liquid admixture for mixing of bonding slurriesand improvement of physical properties for mortars and concretes.
Product Name CEMEBOND LATEX SBR
UsesAs a Prime or bonding agent. Between old and fresh mortars. Can be added tocement mix for better properties.
Packaging 5 L or 25 L.
Coverage 1 L covers 5m2 (as a prime). 2 L for each cement bag (in mix).
Colors None.
ApplicationOn porous substrates and/or with different grades of absorption, in order toprovide a homogeneous surface, apply one coat of pure CEMEBOND LATEX bybrush, broom or roller leaving no puddles. Or mix directly with cement mixes.
Repair Materials:
Back to Repair Materials
Concrete Water Tanks Waterproofing:
Concrete Water Tanks Waterproofing has many system solutions depends on the location, area, weatherconditions , and site conditions.
We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for theconcrete water tanks waterproofing after the Surface Preparation is accomplished we suggest to waterproofthe tanks from inside and outside:Inside Concrete Tank or Well:1. CEMECRYL PRIMER is liquid admixture to improve bonding, workability and curing of mortar and concrete.2. CEMESEAL FLEX is a waterproofing coat for water wells and swimming pools.3. CEMEFLOOR SF400 Epoxy floor coating system designed for protection of concrete floors.
Outside Concrete Tank or Well:4. BITUPRIME EL-10 Cold rubberized bitumen emulsion for underground foundations and walls
waterproofing.
For More Information PleaseClick The Product Name.
Next
Concrete Water Tanks Waterproofing:
1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties ofcement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves themechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction ofwater absorption by capillarity.
Product Name CEMECRYL PRIMER
Uses Porosity sealer and primer applied directly on the surface.
Packaging 5 L or 25 L.
Coverage 1 L Covers 4 m2 @ 100 micron thickness @ smooth surface.
Colors None.
Application
Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry andonce it has been completely absorbed in the support, depending on porosity,apply the mortar or concrete, apply next material within 10 hours afterpriming.
2. CEMESEAL FLEX is a cementitious acrylic two-component product that provides a non-toxic, flexible andwaterproof coating with very high adhesion on those common substrates in construction such as concreteand masonry.
Product Name CEMESEAL FLEX
UsesWaterproofing and protection of water retaining structures, such as drinkingwater tanks, reservoirs, water mains and swimming pools.
Packaging (A) 18 Kg + (B) 5 L.
Coverage Package Covers 20 m2 @ 400 micron thickness.
Colors Grey (Concrete Color).
Application Mix with electrical mixer then apply it using a short, stiff bristle brush or roller.
Concrete Water Tanks Waterproofing:
Previous Next
Concrete Water Tanks Waterproofing:
Previous Next
3. CEMEFLOOR SF400 is a solvent free, two components high build colored system consisting of Epoxy resinand polyamine curing agent. It is designed to provide shameless concrete surface resistance to abrasionand protect against chemical attack.
Product Name CEMEFLOOR SF400
UsesHigh performance epoxy coating with excellent decorative finishing in watertanks, shopping centers, flooring warehouses, floors and walls, and car parking.
Packaging (A) 4.9 Kg + (B) 0.885 Kg
Coverage Package covers 15 m2 @ 200 micron thickness @ smooth surface.
Colors Standard colors (BS4800 or RAL colors are available on request).
Application Mix (A) with (B) using low speed mixer then apply using short hair roller.
4. BITUPRIME EL-10 is an emulsion applied cold on concrete surfaces for waterproofing.
Concrete Water Tanks Waterproofing:
PreviousBack to Tanks
Waterproofing
Product Name BITUPRIME EL-10
UsesApplications from building foundations to bridge abutments, retaining walls,flower boxes, box gutters or any other area where water must be kept in or out.
Packaging 5 L or 18 L or 200 L.
Coverage 1 L Covers 3 m2.
Colors Brown.
ApplicationMix with electric mixer for minutes then apply easily and inexpensively byunskilled personnel. No special equipment is required as application is bynormal brushes, or rollers.
Podium Waterproofing:
Podium Waterproofing has many system solutions depends on the location, area, weather conditions, andsite conditions.
We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for thepodium waterproofing after the Surface Preparation is accomplished we suggest to waterproof the Podiumfrom inside and outside:Inside Podium:1. CEMECRYL PRIMER is liquid admixture to improve bonding, workability and curing of mortar and concrete.2. CEMESEAL FLEX is a waterproofing coat for water wells and swimming pools.
Outside Podium:3. BITUPRIME EL-10 Cold rubberized bitumen emulsion for underground foundations and walls
waterproofing.
For More Information PleaseClick The Product Name.
Next
Podium Waterproofing:
1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties ofcement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves themechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction ofwater absorption by capillarity.
Product Name CEMECRYL PRIMER
Uses Porosity sealer and primer applied directly on the surface.
Packaging 5 L or 25 L.
Coverage 1 L Covers 4 m2 @ 100 micron thickness @ smooth surface.
Colors None.
Application
Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry andonce it has been completely absorbed in the support, depending on porosity,apply the mortar or concrete, apply next material within 10 hours afterpriming.
Previous
Podium Waterproofing:
Next
2. CEMESEAL FLEX is a cementitious acrylic two-component product that provides a non-toxic, flexible andwaterproof coating with very high adhesion on those common substrates in construction such as concreteand masonry.
Product Name CEMESEAL FLEX
UsesWaterproofing and protection of water retaining structures, such as drinkingwater tanks, reservoirs, water mains and swimming pools.
Packaging (A) 18 Kg + (B) 5 L.
Coverage Package Covers 20 m2 @ 400 micron thickness.
Colors Grey (Concrete Color).
Application Mix with electrical mixer then apply it using a short, stiff bristle brush or roller.
PreviousBack to Podium
Waterproofing
Podium Waterproofing:
3. BITUPRIME EL-10 is an emulsion applied cold on concrete surfaces for waterproofing.
Product Name BITUPRIME EL-10
UsesApplications from building foundations to bridge abutments, retaining walls,flower boxes, box gutters or any other area where water must be kept in or out.
Packaging 5 L or 18 L or 200 L.
Coverage 1 L Covers 3 m2.
Colors Brown.
ApplicationMix with electric mixer for minutes then apply easily and inexpensively byunskilled personnel. No special equipment is required as application is bynormal brushes, or rollers.
Decorative Plaster:
Decorative Plaster has many system solutions depends on the location, area, weather conditions, and siteconditions.
We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for thedecorative plaster after the Surface Preparation is accomplished we suggest CEMECRYL PRIMER which is liquidadmixture to improve bonding, workability and curing of mortar and concrete, then we use the PLASTERPROFILE which is a decorative weatherproofing plaster application for internal and external use on concrete,plaster, mortar and masonry surfaces (multi-colors), then again use CEMECRYL PRIMER to get a protective coatfor the plaster profile.
For More Information PleaseClick The Product Name.
Next
Decorative Plaster:
1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties ofcement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves themechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction ofwater absorption by capillarity.
Product Name CEMECRYL PRIMER
Uses Porosity sealer and primer applied directly on the surface.
Packaging 5 L or 25 L.
Coverage 1 L Covers 4 m2 @ 100 micron thickness @ smooth surface.
Colors None.
Application
Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry andonce it has been completely absorbed in the support, depending on porosity,apply the mortar or concrete, apply next material within 10 hours afterpriming.
Decorative Plaster:
2. PLASTER PROFILE is a dry mix of cement and selected aggregates, modified with polymers. Just needs toadd water at site to provide a decorative colored finish.
Product Name Plaster Profile
Uses Colored plaster for outdoor and indoor use.
Packaging 25 Kg.
Coverage Package covers 7 m2 @ smooth surface.
Colors 20 colors (BS4800 or RAL colors are available on request).
ApplicationMixing 25 Kg with 5 L water apply using steel trowel or hopper spray gun andallowed partly, set before finally troweling to a smooth surface, differentprofiles can be achieved by using mechanical tools.
PreviousBack to
Decorative Plaster
Courts Flooring Solution:
Courts Flooring has many system solutions depends on the location, area, weather conditions, and siteconditions.
We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for the courtsflooring after the Surface Preparation is accomplished we suggest CEMECRYL PRIMER which is liquidadmixture to improve bonding, workability and curing of mortar and concrete, then we use the CEMELASTICPATCH which is a sport flooring system. multipurpose acrylic and quartz aggregate compounds, then we useCEMEFLOOR COURT PAINT which is a high quality water base anti-skidding paint for sport flooring based onspecial type of acrylic emulsion.
For More Information PleaseClick The Product Name.
Next
Courts Flooring Solution:
1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties ofcement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves themechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction ofwater absorption by capillarity.
Product Name CEMECRYL PRIMER
Uses Porosity sealer and primer applied directly on the surface.
Packaging 5 L or 25 L.
Coverage 1 L Covers 4 m2 @ 100 micron thickness @ smooth surface.
Colors None.
Application
Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry andonce it has been completely absorbed in the support, depending on porosity,apply the mortar or concrete, apply next material within 10 hours afterpriming.
2. CEMELASTIC PATCH is an elastic acrylic system, specially formulated for all types of surfaces. It is suppliedin the form of a water-based two component, just need to mix at site. UV-rays resistant and non-degradable elastomeric, providing rubberized basecoat to achieve either a professional or intermediateplaying surface
Product Name CEMELASTIC PATCH
UsesIts designed as a basecoat for the Courts Flooring System for levelling and
coating.
Packaging (A) 20 Kg + (B) 50 Kg.
Coverage Package Covers 15 m2 @ 2 mm thickness.
Colors Grey, Green, Red, and Beige (BS4800 or RAL colors are available on request).
ApplicationApply with trowel and level with a float. Smooth finishing can be achieved witha wooden or foam float.
Next
Courts Flooring Solution:
Previous
3. CEMEFLOOR COURT PAINT is water based acrylic formulation that has been developed for the painting of asphalt, andtarmac tennis courts. Suitable for use on both internal and external applications, has good resistance to UV light. It is atough, hard wearing paint that possesses wear resistance to medium traffic in parking areas and sport courtsapplications.
Product Name CEMEFLOOR COURT PAINT
UsesAs a finish coat for indoor and outdoor court ground on concrete or asphaltsubstrate, and for parking areas, roads and curbstones with medium traffic.
Packaging 5 Kg or 18 Kg.
Coverage 1 L Covers 4 m2 per coat.
Colors White, Black, Red, and Yellow.
Application Apply using a roller. 2 coats is a must.
PreviousBack to Courts
Flooring Solution
Courts Flooring Solution:
Stamped Concrete:
Stamped concrete has many system solutions depends on the location, area, weather conditions, and siteconditions.
We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for thestamped concrete after the Surface Preparation is accomplished we suggest CEMEHARD 100 which is a dry-Shake cement hardener powder for concrete surfaces, before using the rubber stamps it’s a must to useCEMERELEASE AGENT which is a powder used to block the concrete from adhesion with the rubber stamps,then as a final coat use CEMEFLOOR GLAZE which is a transparent polymer sealer, gloss finish, for protection ofconcrete, and retain the color.
For More Information PleaseClick The Product Name.
1. CEMEHARD 100 is formulated with special cements, pigments, additives and aggregates designed to beapplied on fresh concrete in order to improve its abrasion resistance and provides an anti-dust coloredfinish in one single application.
Product Name CEMEHARD 100
Uses Pavements of garages, parking, shopping malls, schools, hospitals.
Packaging 25 Kg.
Coverage 3 Kg covers 1 m2.
Colors 20 colors available.
Applicationspread the powder over the whole surface. Wait until it becomes moist. Do not
wet the surface of the concrete during the application. Compact with help of atroweling machine.
Stamped Concrete:
Next
2. CEMERELEASE AGENT is a powder Release agent used in the Stamped concrete process to avoid adhesivebetween concrete and rubber stamps.
Product Name CEMERELEASE AGENT
UsesAs a release agent from concrete in the Stamping process, and act as a
secondary colorant.
Packaging 10 Kg.
Coverage 1 Kg covers 3 m2.
Colors Depends on the application.
Application Spread with hand over the troweled concrete and CEMEHARD 100.
Next Previous
Stamped Concrete:
PreviousBack to
Stamped Concrete
Stamped Concrete:
3. CEMEFLOOR GLAZE is a transparent polymer sealer, derived from methacrylate-based resins. It forms adurable, tough and flexible film with gloss finish for protection of concrete and masonry. It resistsweathering, air pollutants, alkaline agents and ultra-violet rays (UV).
Product Name CEMEFLOOR GLAZE
UsesClear acrylic developed to provide hard, glossy, Protective Sealer to beautifyand protect regular concrete surface.
Packaging 5 L or 25 L.
Coverage 1 L Covers 4 m2 @ 150 microns thickness per coat @ smooth surface.
Colors None.
Application Apply with brush, roller, or spray, 2 coats recommended.
Decorative Floors has many system solutions depends on the location, area, weather conditions, and siteconditions.We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products:
System 1: In our First system to meet the highest quality of Decorative Floors before applying any productsurface preparation must be accomplished then start applying the system products.
1. CEMEFLOOR SF400 Epoxy floor coating system designed for protection of concrete floors.2. FLAKE CHIPS Small chips designed to give a multi colors.3. CEMEFLOOR SLC - CLEAR Non-Colored self-leveling epoxy system.
Decorative Floors:
System 2
For More Information PleaseClick The Product Name.
Decorative Floors has many system solutions depends on the location, area, weather conditions, and siteconditions.We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products:
System 2: In our Second system to meet the highest quality of Decorative Floors before applying any productsurface preparation must be accomplished then start applying the system products.
1. CEMEFLOOR METAL FUSION Decorative self-leveling epoxy floor system for protection of concrete floors.
Decorative Floors:
System 3System 1
For More Information PleaseClick The Product Name.
Decorative Floors has many system solutions depends on the location, area, weather conditions, and siteconditions.We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products:
System 3: In our Third system to meet the highest quality of Decorative Floors before applying any productsurface preparation must be accomplished then start applying the system products.
1. CEMEFLOOR GLITTER Decorative self-leveling epoxy floor system for protection of concrete floors.
Decorative Floors:
System 2
For More Information PleaseClick The Product Name.
Next
Decorative Floors:
1. CEMEFLOOR SF400 is a solvent free, two components high build colored system consisting of Epoxy resinand polyamine curing agent. It is designed to provide shameless concrete surface resistance to abrasionand protect against chemical attack.
Product Name CEMEFLOOR SF400
UsesHigh performance epoxy coating with excellent decorative finishing in watertanks, shopping centers, flooring warehouses, floors and walls, and car parking.
Packaging (A) 4.9 Kg + (B) 0.885 Kg
Coverage Package covers 15 m2 @ 200 micron thickness @ smooth surface.
Colors Standard colors (BS4800 or RAL colors are available on request).
Application Mix (A) with (B) using low speed mixer then apply using short hair roller.
3. CEMEFLOOR SLC - CLEAR is a clear self-leveling epoxy system, used for apply at multi-thicknesses. nonyellowing, non scratch and high bond strength. chemical and abrasion resistance.
Product Name CEMEFLOOR SLC - CLEAR
Uses Typical uses for: 3D Flooring Systems and as Protective Top Coat for indoors.
Packaging 5 L.
Coverage Package covers 5 m2 @ 1 mm thickness @ smooth surface.
Colors None.
ApplicationApplication should be spread on the prepared surface with a notched trowel.Finish off with a spike roller, dense short lambs wool roller, brush, etc. torelease entrapped air.
Decorative Floors:
PreviousBack to
Decorative Floors
1. CEMEFLOOR METAL FUSION is designed to create elegant and exotic looking seamless floors. Metal Fusionis a two component epoxy formulation consisting of a high performance epoxy resin A blend combinedwith a curing agent B.
Product Name CEMEFLOOR METAL FUSION
UsesIdeal for residential and commercial use including, living rooms, kitchens,bathrooms, office spaces, lobby areas etc..
Packaging (A) 4.5 Kg + (B) 1.5 Kg
Coverage Package covers 5 m2 @ 1mm thickness @ smooth surface.
Colors Available in 15 standard metallic colors.
ApplicationMix (A) + (B) using slow speed mixer Spread the Metal Fusion using notchedsqueegee and follow behind with a spiked roller. Roll several times with spikedroller.
Decorative Floors:
Back to Decorative
Floors
1. CEMEFLOOR GLITTER is designed to create elegant and glittering looking seamless floors is two componentself-leveling consisting of a high performance epoxy resin a blend combined with a curing agent B.
Product Name CEMEFLOOR GLITTER
UsesIdeal for residential and commercial use including, living rooms, kitchens,bathrooms, retail stores, office spaces, lobby areas etc..
Packaging (A) 4.5 Kg + (B) 1.5 Kg.
Coverage Package covers 5 m2 @ 1mm thickness @ smooth surface.
Colors Available in 5 standard glitter colors.
ApplicationSpread the Glitter using notched squeegee and follow behind with a spikedroller. Roll several times with spiked roller.
Decorative Floors:
Back to Decorative
Floors
Parking & Industrial Floors are specifically formulated to stand up to the extremes of industrial andmanufacturing environments. Ideally suited for manufacturing and assembly areas, forklift aisles and loadingdocks, Floor systems withstand the constant abuse of heavy loads, impacts, forklift traffic and exposure toliquids and chemical, to meet the highest quality of our products surface preparation must be accomplished.
1. CEMEFLOOR SL 200 Epoxy floor self-leveling high gloss abrasion resist.2. CEMEFLOOR SF400 Epoxy floor coating system designed for protection of concrete floors3. CEMEFLOOR SL-ELASTIC Elastic self-leveling epoxy.4. CEMEFLOOR COLOR COAT Flooring coating interior and exterior, waterproofing, and decorative, and
industrial.
Parking & Industrial Floors: For More Information Please
Click The Product Name.
1. CEMEFLOOR SL200 is a seamless, Self-Leveling flooring system based on an advanced solvent free epoxysystem and selected graded aggregate. The smooth impervious surface finish provides an easily cleanedand hygienic surface with excellent resistance to chemical and mechanical attack.
Product Name CEMEFLOOR SL200
UsesIdeal for Industrial, Pharmaceutical, cosmetic industries, food factories, andstores.
Packaging (A) + (B) + (C) = 12 L.
Coverage Package covers 6 m2 @ 2mm thickness @ smooth surface.
Colors Standard colors (BS4800 or RAL colors are available on request).
ApplicationMix (A) + (B) + (C) using slow speed mixer apply into using a notched or flattrowel to a typical thickness of 2mm minimum the surface should be spikerolled to remove the entrapped air, ensure application is continuous.
Back to Parking & Industrial
Parking & Industrial Floors:
Parking & Industrial Floors:
Back to Parking & Industrial
2. CEMEFLOOR SF400 is a solvent free, two components high build colored system consisting of Epoxy resinand polyamine curing agent. It is designed to provide shameless concrete surface resistance to abrasionand protect against chemical attack.
Product Name CEMEFLOOR SF400
UsesHigh performance epoxy coating with excellent decorative finishing in watertanks, shopping centers, flooring warehouses, floors and walls, and car parking.
Packaging (A) 4.9 Kg + (B) 0.885 Kg
Coverage Package covers 15 m2 @ 200 micron thickness @ smooth surface.
Colors Standard colors (BS4800 or RAL colors are available on request).
Application Mix (A) with (B) using low speed mixer then apply using short hair roller.
3. CEMEFLOOR SL-ELASTIC is a self-leveling epoxy system based on special epoxy resin. Vibration and impactresistance due to advanced formula of elastic compounds. While maintaining the hygienic finish withexcellent bonding strength and chemical resistance.
Product Name CEMEFLOOR SL-ELASTIC
Uses Ideal for Industrial, Pharmaceutical, cosmetic industries, and vibration areas.
Packaging (A) + (B) = 3.6 L.
Coverage Package covers 3.6 m2 @ 1mm thickness @ smooth surface.
Colors Standard colors (BS4800 or RAL colors are available on request).
ApplicationApplied using a notched or flat trowel to a typical thickness of 2mm minimumthe surface should be spike rolled to remove the entrapped air, ensureapplication is a continuous.
Parking & Industrial Floors:
Back to Parking & Industrial
4. CEMEFLOOR COLOR COAT is a modified formulated thermoplastic based coating, designed to work as asingle component quick curing protective coating for concrete and asphalt floors and walls. Provides a UVresistant waterproofing and abrasion resistant surface.
Product Name CEMEFLOOR COLOR COAT
Uses Ideal for Industrial, outdoor areas, parking, and roofs.
Packaging 5 Kg or 20 Kg.
Coverage 1 Kg covers 4 m2 @ 150 micron @ smooth surface.
Colors Standard colors (BS4800 or RAL colors are available on request).
Application Easy to apply by a brush, roller, spray. 2 coats is a must.
Parking & Industrial Floors:
Back to Parking & Industrial
Tiles Adhesive & Grout has many system solutions depends on the location, area, weather conditions, and siteconditions.We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products:
System: In our system to meet the highest quality of Tiles Adhesive & Grout before applying any productsurface preparation must be done then start applying the system products.
1. Tile-Fix Standard quality tile adhesive – General use.2. Tile-Fix 100 High quality tile adhesive for fixing ceramic tiles on interior and exterior floors and
walls surfaces, high durability to water spells and moisture.3. Tile-Fix 200 Super quality tile adhesive for fixing all types of tiles and vertical stone cladding for interior
and exterior uses, waterproof and open time wet, used for pools and wet areas.4. Tile-Fix 300 Very high quality and durability tile adhesive for special needs, and hardest conditions.5. ULTRA-GROUT Tile joint filling grout for general use.6. ULTRA-GROUT UW High quality waterproofing joint filling grout, recommended for immersed tiles and
swimming pools use.
Tiles Adhesive & Grout: For More Information Please
Click The Product Name.
1. Tile-Fix is a standard quality adhesive for the permanent fixing of ceramic, vitrified, and porcelain tiles
Product Name Tile-Fix
Uses permanent fixing of ceramic, vitrified, and porcelain tiles. Floors and walls.
Packaging 20 Kg.
Coverage Package covers 7 m2 @ 2 mm.
Colors White.
ApplicationMix 20 Kg with 4 L water, should be spread on the substrate to a uniform
thickness of 2-3mm, and then combed horizontally with a serrated trowel, andfix tile.
Back to Tiles adhesive &
Grout
Tiles Adhesive & Grout:
2. Tile-Fix 100 is a high quality adhesive for the permanent fixing of ceramic, vitrified, and porcelain tiles.
Product Name Tile-Fix 100
Usespermanent fixing of ceramic, vitrified, and porcelain tiles. Indoor and outdoor,
floors and walls.
Packaging 20 Kg.
Coverage Package covers 7 m2 @ 2 mm.
Colors White.
ApplicationMix 20 Kg with 4 L water, should be spread on the substrate to a uniformthickness of 2-3mm, and then combed horizontally with a serrated trowel.
Back to Tiles adhesive &
Grout
Tiles Adhesive & Grout:
3. Tile-Fix 200 is a super quality adhesive for the permanent fixing of glass mosaic tiles and vertical stonecladding.
Product Name Tile-Fix 200
Uses All types tiles and vertical stone cladding, wet areas and swimming pool.
Packaging 20 Kg.
Coverage Package covers 7 m2 @ 2 mm.
Colors White.
ApplicationMix 20 Kg with 4 L water, should be spread on the substrate to a uniformthickness of 2-3mm, and then combed horizontally with a serrated trowel.
Back to Tiles adhesive &
Grout
Tiles Adhesive & Grout:
4. Tile-Fix 300 is a special quality adhesive for the permanent fixing of tiles in damp and totally submergedconditions, for heavy tiles and stone, for special harsh environments.
Product Name Tile-Fix 300
Uses Swimming pools, Fountains, Bathroom floors, Splash zones, and heavy stones.
Packaging 20 Kg.
Coverage Package covers 7 m2 @ 2 mm.
Colors White.
ApplicationMix 20 Kg with 4 L water, should be spread on the substrate to a uniformthickness of 2-3mm, and then combed horizontally with a serrated trowel.
Back to Tiles adhesive &
Grout
Tiles Adhesive & Grout:
5. ULTRA-GROUT is a polymer based cementitious tile joint filler used in filling gaps and levels itself to givehard wearing, non dusting, anti-fungus tile joints.
Product Name ULTRA-GROUT
Uses It provides smooth water resistant hard wearing tile joints.
Packaging 5 Kg or 20 Kg.
Coverage Package 5 Kg covers 15 m2 @ 2 mm joint width.
Colors 14 Colors.
ApplicationMix 5 Kg with 1 L water apply the mix to the tile joints with a steel or plastictrowel, then smoothen with a sponge.
Back to Tiles adhesive &
Grout
Tiles Adhesive & Grout:
6. ULTRA-GROUT UW is a two component tile joint filling grout, powder and resin to be mixed on site, forexterior or under water applications, such as kitchens bathrooms and swimming pools, anti-fungus tilejoints.
Product Name ULTRA-GROUT UW
UsesIt provides smooth water resistant hard wearing tile joints for under water andexterior use.
Packaging (A) 5 Kg + (B) 1 L.
Coverage Package covers 15 m2 @ 2 mm joint width.
Colors 14 Colors.
ApplicationMix (A) 5 Kg with (B) 1 L using a slow speed mixer then apply to the joint usinga steel trowel.
Back to Tiles adhesive &
Grout
Tiles Adhesive & Grout:
Swimming Pool Waterproofing:
Swimming pool Waterproofing has many system solutions depends on the location, area, weatherconditions, and site conditions.
We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products, as for theSwimming pool waterproofing after the Surface Preparation is accomplished we suggest to waterproof thetanks from inside and outside:Inside Swimming Pool:1. CEMECRYL PRIMER is liquid admixture to improve bonding, workability and curing of mortar and concrete.2. CEMESEAL FLEX is a waterproofing coat for water wells, and swimming pools.3. Tile-Fix 300 Very high quality and durability tile adhesive for special needs.4. ULTRA-GROUT UW High quality waterproofing joint filling grout, recommended for immersed tiles and
swimming pools use
Outside Swimming Pool:5. BITUPRIME EL-10 Cold rubberized bitumen emulsion for underground foundations and walls
waterproofing.
For More Information PleaseClick The Product Name.
Next
Swimming Pool Waterproofing:
1. CEMECRYL PRIMER is a water-based pure acrylic product to be used as an admixture to increase both physical and chemical properties ofcement-based mortars and concrete. And provide greater adhesion, workability, cohesion and water retention, and improves themechanical resistances to compressive and flexural strength, enhances abrasion and wearing resistance, and provides a reduction ofwater absorption by capillarity.
Product Name CEMECRYL PRIMER
Uses Porosity sealer and primer applied directly on the surface.
Packaging 5 L – 25 L.
Coverage 1 L Covers 4 m2 @ 100 micron thickness @ smooth surface.
Colors None.
Application
Apply as primer by brush, roller, or spray leaving no puddles. Allow it to dry andonce it has been completely absorbed in the support, depending on porosity,apply the mortar or concrete, apply next material within 10 hours afterpriming.
Previous Next
Swimming Pool Waterproofing:
2. CEMESEAL FLEX is a cementitious acrylic two-component product that provides a non-toxic, flexible andwaterproof coating with very high adhesion on those common substrates in construction such as concreteand masonry.
Product Name CEMESEAL FLEX
UsesWaterproofing and protection of water retaining structures, such as drinkingwater tanks, reservoirs, water mains and swimming pools.
Packaging (A) 18 Kg + (B) 5 L.
Coverage Package Covers 20 m2 @ 400 micron thickness.
Colors Grey (Concrete Color).
Application Mix with electrical mixer then apply it using a short, stiff bristle brush or roller.
Previous Next
Swimming Pool Waterproofing:
3. Tile-Fix 300 is a special quality adhesive for the permanent fixing of tiles in damp and totally submergedconditions, for heavy tiles and stone, for special harsh environments.
Product Name Tile-Fix 300
Uses Swimming pools, Fountains, Bathroom floors, Splash zones, and heavy stones.
Packaging 20 Kg.
Coverage Package covers 7 m2 @ 2 mm.
Colors White.
ApplicationMix 20 Kg with 4 L water, should be spread on the substrate to a uniformthickness of 2-3mm, and then combed horizontally with a serrated trowel.
Previous Next
Swimming Pool Waterproofing:
4. ULTRA-GROUT UW is a two component tile joint filling grout, powder and resin to be mixed on site, forexterior or under water applications, such as kitchens bathrooms and swimming pools, anti-fungus tilejoints.
Product Name ULTRA-GROUT UW
UsesIt provides smooth water resistant hard wearing tile joints for under water andexterior use.
Packaging (A) 5 Kg + (B) 1 L.
Coverage Package covers 15 m2 @ 2 mm joint width.
Colors 14 Colors.
ApplicationMix (A) 5 Kg with (B) 1 L using a slow speed mixer then apply to the joint usinga steel trowel.
5. BITUPRIME EL-10 is an emulsion applied cold on concrete surfaces for waterproofing.
PreviousBack to
Swimming pool
Swimming Pool Waterproofing:
Product Name BITUPRIME EL-10
UsesApplications from building foundations to bridge abutments, retaining walls,flower boxes, box gutters or any other area where water must be kept in or out.
Packaging 5 L or 18 L or 200 L.
Coverage 1 L Covers 3 m2.
Colors Brown.
ApplicationMix with electric mixer for minutes then apply easily and inexpensively byunskilled personnel. No special equipment is required as application is bynormal brushes, or rollers.
Basement & Foundation Waterproofing has many system solutions depends on the location, area, weatherconditions, and site conditions.We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products :
System: In our system to meet the highest quality of Basement & Foundation Waterproofing before applyingany product surface preparation must be accomplished then start applying the system products.
1. BITUPRIME Cold rubberized bitumen emulsion for underground foundations waterproofing.2. BITUFLEX EL-5 Cold rubberized bitumen emulsion for underground foundations waterproofing 5%
rubberized.3. BITUFLEX EL-10 Cold rubberized bitumen emulsion for underground foundations waterproofing 10%
rubberized
Basement & Foundation Waterproofing: For More Information
Please Click The ProductName.
1. BITUPRIME a cold rubberized bitumen emulsion, easily applied for waterproofing of undergroundfoundation.
Product Name BITUPRIME
UsesApplications from building foundations to bridge abutments, retaining walls,flower boxes, box gutters or any other area where water must be kept in or out.
Packaging 5 L or 18 L or 200 L.
Coverage 1 L Covers 3 m2.
Colors Brown.
ApplicationMix with electric mixer for minutes then apply easily and inexpensively byunskilled personnel. No special equipment is required as application is bynormal brushes, or rollers.
Back to Basement & Foundations
Basement & Foundation Waterproofing:
2. BITUPRIME EL-5 is a highly effective and cost efficient method of waterproofing brick, concrete. It is arubber bitumen emulsion which when dries form a tough, elastic membrane.
Back to Basement & Foundations
Basement & Foundation Waterproofing:
Product Name BITUPRIME EL-5
UsesApplications from building foundations to bridge abutments, retaining walls,flower boxes, box gutters or any other area where water must be kept in or out.
Packaging 5 L or 18 L or 200 L.
Coverage 1 L Covers 3 m2.
Colors Brown.
ApplicationMix with electric mixer for minutes then apply easily and inexpensively byunskilled personnel. No special equipment is required as application is bynormal brushes, or rollers.
Back to Basement & Foundations
Basement & Foundation Waterproofing:
3. BITUPRIME EL-10 is an emulsion applied cold on concrete surfaces for waterproofing.
Product Name BITUPRIME EL-10
UsesApplications from building foundations to bridge abutments, retaining walls,flower boxes, box gutters or any other area where water must be kept in or out.
Packaging 5 L or 18 L or 200 L.
Coverage 1 L Covers 3 m2.
Colors Brown.
ApplicationMix with electric mixer for minutes then apply easily and inexpensively byunskilled personnel. No special equipment is required as application is bynormal brushes, or rollers.
Stone Facades Waterproofing has many system solutions depends on the location, area, weather conditions,and site conditions.We CEMENTSOLUTIONS have the high quality standards with the reasonable prices products:
System: In our system to meet the highest quality of Stone Facades Waterproofing before applying any productsurface preparation must be done then start applying the system products.
1. ULTRA-HOLD High quality waterproofing joint filler for limestone joints.2. ACRY-SEAL WB High quality water-base proof for limestone.3. SILO-SEAL WB Water base water-repellent for stone protection colorless and ready to use.4. SILO-SEAL SB Solvent base water-repellent for stone protection colorless and ready to use
Stone Facades Waterproofing: For More Information Please
Click The Product Name.
1. ULTRA-HOLD is a dry mix mortar, highly modified to work as a joint filler at stone facades. Its waterproofingand non-shrink.
Back to Stone Facades
Stone Facades Waterproofing:
Product Name ULTRA-HOLD
Uses To fill limestone joints.
Packaging 25 Kg.
Coverage Depends on joint width and depth.
Colors White, Yellow, and Grey (BS4800 or RAL colors are available on request).
ApplicationMix 25 Kg with 5 L of water then apply the mix to the joint with a steel troweland a sponge.
2. ACRY-SEAL WB is a non-staining water-repellent liquid composed of milky siloxane silane resin speciallyformulated for limestone substrate, plaster or similar, low-fired clay and gypsum plasters.
Stone Facades Waterproofing:
Product Name ACRY-SEAL WB
Uses Invisible protection for limestone façades and exterior plasters.
Packaging 25 L.
Coverage Package covers 100 m2.
Colors None.
Application Applied by brush, roller, or low pressure spray.
Back to Stone Facades
3. SILO-SEAL WB is a water-repellent liquid composed of invisible water-based silicon resin speciallyformulated for limestone substrates or similar, low-fired clay and gypsum plasters.
Stone Facades Waterproofing:
Product Name SILO-SEAL WB
Uses Invisible protection for limestone façades and exterior plasters.
Packaging 5 L or 25 L.
CoveragePackage covers 20 m2.Or Package covers 100 m2.
Colors None.
Application Applied by brush, roller, or low pressure spray.
Back to Stone Facades
4. SILO-SEAL SB is a solvent base water-repellent, for protection and waterproofing of stone or plasterfacades.
Stone Facades Waterproofing:
Product Name SILO-SEAL SB
Uses Invisible protection for limestone façades and interior plasters.
Packaging 5 L or 25 L.
CoveragePackage covers 20 m2.Or Package covers 100 m2.
Colors None.
Application Applied by brush or low pressure spray.
Back to Stone Facades
Surface Preparation:
Repair any crack or holes.
Surface smoothing or grinding depending on application.
Surface must be cleaned.
Surface must be free of any contaminants such as oil, grease or otherincompatible materials.
Surface must be shot blasting or dustless grinding these are common surface insome cases preparation methods.
