AFT OnlineTooling Catalogue

AEROSPACE & SHEETMETAL ASSEMBLY TOOLING SPECIALISTS

MONOGRAM AEROSPACE FASTENERS®

A Drills Pnuematic 45-47 Rivet Nut Tools 44

Abrasives 79,80 Drills Angle Pnuematic 51-55 Rivet Sets 13-24

Abrasive Blasting Equipment 126 E Rivet Shavers 34,72

Abrasive Power Tools,Dynabrade 71 Engraving Pens 125,129 Rivet Squeezers Pnuematic 1,2,4,5,6

Air Hammers 10,11,26 Everede Eversinks 101 Rivet Squeezers Hand 3

Air Hammer Accessories 12-24 Extractors 59 Riveters (Deep Throat) 4,5,6

Air Line Accessories 133 F Roller Ratchets 123

Alligator Riveters 1 File Pnuematic 71,125 Rotary Files (Carbide) 81

Angle Drills 51-55 Files Hand 132 Routers Air 82,83

Angle Drill Attachments 49-50 Flaring Tool 107 Router Bits 59

B G SBack Countersinks,Spotfacers 90-92 Grinders 72-77 Sand Blasters 126

Balancers 66 H Sanders 69-74,78

Beading Tool 107 Hand Tools 104,107,108 Saws Air 84-87,129

Belt Sanders 70,71,73 Heat Gun 125 Scaler Chipper Air 129

Bits -Screwdriver Bits 66 Helicoil Tools 112-114 Scaler Needle Air 129

Blind Riveters 27-33 Hi Lok Type Collar Tools 118-124 Screwdriver bits and accessories 66

BoeLube 136 Hole Cutters 104 Screwdrivers 63-66

Brakes, Sheetmetal 127 Hole Finders Blind 104 Screw Extractors 59

Breakloose Tool 18 Hole Saws 98 Sealant Guns Pnuematic 102-103

Brushes, Pilot 57 Hole Spotters 104 Shears Pnuematic 127-128

Bucking Bars 25,26 Hose (Air Hoses) 133 Sheetmetal Clamps (Clecos) 60-61

C Huck Riveters 35-42 Sheetmetal Machinery 127-128

Cable Swager 115,116 I Shrinkers Stretchers 128

Cable Tensiometer 124 Impact Wrenches 68 Snap Socs 135

Camloc Plier 107 Jo Bolt Tooling 117 Snips (Aviation L and R ) 107

Carbide Countersinks 89,94,95,101 K Spray Gun 125

Carbide Rotary Files 81 Knock out Punches 24 Squeezers Rivet 1-6

Cherry Rivet tooling 27-32 L Step Drills 56

Chisels 12,18,131 "Lightning" Hole Punches 130 Strap Duplicators (Hole Finders) 104

Chucks, Drill 45,53 Lockbolt Tooling 32,36-42 Swaging Machines 115,116

Clamps 60-62 N TClecos 60,61 Needle Scaler 11 Tapping Tools (Air) 58

Coil Hoses 133 Nibbler Air 127 Tensiometers 124

Collar Cutters 93 Nibbler Hand 107 Testing Equipment 124

Collar Tools (Hi Lok Type) 118-124 Nutplate Spacematic Tooling 106 Toggle Clamps 62

Collets, Drill 53 Nutrunners 63-66 Torque Wrenches 67

Composite Cutting Tools 99-101 O Transfer Punches 17

Compression Riveters 1-2,4-6 Oil (Airtool) 133 Tube Blender 108

Counterbores 90,91,95 Oilers 133 U

Countersink Cutters 88,89,95,96,97 P Unibits (Step drills) 56

Countersink Microstops 88 Paint Cutters 136 V

Cut Off Wheels 78 Plate Nut Drill Jigs (Hand) 105 Vacuums (Compressed Air) 133-134

Cutting Tools 88-101 Polisher (Aircraft) 126 Vises 62

D Pop Riveters 43 Vise Grips 107

Deburring Tools 109-111 Protractors Propeller 124 Visulok Tooling 117

Diamond Tooling 100-101 Punches 13,17,24,129,130,131 W

Dimple Sets 9 R Wheels (Cut Off) 78

Drill Attachments 49-50 Reamers 59 Wire Twister (Milbar Safety) 108

Drill Bits 53,56,57,99 Regulators 12,133 Y

Drill Bushing Assembly (Egg Cup) 48 Rivet Cutters 104 Yolks for Rivet Squeezers 3

Drill Nut Plate Jigs 105 Rivet Fan Spacing Tool 13 Z

Drill Stops 57 Rivet Hammers 10-11,26 Zephyr Countersinks and Cutters 88

Tooling Index

Ph +61 498 610 566 [email protected]

ALLIGATOR YOKE-COMPRESSION RIVETERS

CAPACITYCOLD RIVET

EXPERT

REPAIRSREBUILTSAVAILABLE

Alum.(inch)

Steel(inch)

Reach(inch)

Gap(inch)

CLOSED HEIGHT

(inch)

MAX TRAVEL

(inch)

STANDARD JAWMOVING JAW

MAX FORCEWITH 90

PRESSURE(lbs)

PART OFSTROKE ATMAX FORCE

(final inch)

NETWEIGHT

WITHJAWS(lbs)

1/8 3/32 1-1/2 1-5/8 7/8 5/8 3000 1/16 3-3/41/8 3/32 2-1/4 1-7/8 7/8 7/8 2200 1/16 4-1/43/32 1/16 3 2 7/8 1-1/4 1800 1/16 4-1/2

3/16 5/32 1-1/2 1-5/8 7/8 5/8 6000 1/16 5-1/25/32 1/8 2-1/4 2-1/8 7/8 7/8 4300 3/32 61/8 3/32 3 2-1/8 7/8 1-1/4 3400 1/8 6-1/4

MODEL 3000A(Equivalent to the CP 0214-ANBEL, ANFEL, ANGEL) (APT / 710A)

MODEL 6000A(Equivalent to the CP 0214-ENBEL, ENFEL, ENGEL) (APT 725 A)

3/16 5/32 2-7/8 1-5/8 7/8 5/8 5200 1/8 15-3/45/32 1/8 5 1-5/8 7/8 1-3/8 3400 3/16 19-3/41/8 3/32 7 2-1/8 1-1/2 1-11/16 3000 3/16 24-1/21/8 3/32 9-1/8* 2-1/8 3/4 1-11/16 3000 1/16 26-1/4

MODEL 151A(Equivalent to the CP 0351 - ASGEL,ASKEL, ASREL, ASVEL -APT 740A)

1/4 3/16 2-7/8 1-5/8 7/8 5/8 10,400 1/8 18-1/23/16 5/32 5 1-5/8 7/8 1-3/8 6800 3/16 22-1/23/16 5/32 7 2-1/8 1-1/2 1-11/16 6000 3/16 273/16 5/32 9-1/8 2-1/8 3/4 1-11/16 6000 1/16 29

TANDEM VERSION MODEL 151 TA(Equivalent to CP 0351 – ESGEL, ESKEL, ESREL, ESVEL, APT 750A)

BENCH STAND

EnablesmountingRiveter toany surface

(Specify)For: CP351A, 151A, 151TA

SERIES No. 351-BS

SEE PAGES 7,8, 9 FOR.187 SHANK SQUEEZER SETS

FITS ALL ALLIGATORTYPE RIVETERS

“EXCLUSIVEADVANCED AIR TOOL

DESIGN”

*PICTURED WITH OUR CUSTOM MFG.AIR OPERATED FLOOR STAND

No. 351 AFS..... FLOOR STAND ONLY

No. 351 FS AIR OPERATED CONTROL ONLY

NO. 351 AFB.....

AIR OPERATED FLOOR STAND #351 AFS

OTHERTYPE STANDS AVAILABLE

1

COMPRESSION RIVETERS – “C” YOKE

2

Expert Repairs on All Brands Rebuilts Available - Inquire

SPECIAL "C" YOKES AVAILABLE - SEE PAGE 3.PAGES 7,8,9 FOR .187 SHANK SQUEEZER SETS.

CAPACITYCOLD RIVET

Alum.(inch)

Steel (inch)

Reach (inch)

Gap (inch)

CLOSEDHEIGHT

(inch)MAX.

TRAVEL (inch)

PART OF STROKEAT MAX FORCE

(final) (inch)

STANDARD"C" YOKE

SET HOLDER PLUNGERNET

WEIGHTWITHYOKE(lbs.)

1/8 3/32 1-1/2 1-1/4 11/16 9/16 1/16 4-1/2

3/16 5/32 1-1/2 1-1/4 11/16 9/16 1/16 5-1/2

3/16 5/32 2-1/8 1-3/16 25/32 9/16 1/8 12-1/2

1/4 7/32 2-1/8 1-3/16 25/32 9/16 1/8 15

1/4 7/32 2-1/8 2-1/4 1-1/32 7/8 1/32 21

MODEL 3000C(Equivalent to CP 0214-CELEL)

(APT 705C)

MODEL 6000C(Equivalent to CP 0214-FALEL)

(APT 720C)

MODEL 151C(Equivalent to CP 0351-CUDEL

APT 740C)

MODEL 151T C(Equivalent to CP 0351-FUDEL-

APT 74OC-268)

MODEL 155(Equivalent to CP 0355-CEBEL)

#268 TANDEM CONVERSION ASS'Y ONLY(Reference A)

SUPERPORTABLEPUNCH

• Quicker And Cheaper Than Drilling • 3/16" Max. Material Thickness• Makes Clean, Accurate Holes Without Burrs • 5/16" Max. Hole Diameter• 5400 lbs. Punching Force Max. • 17⁄8" Reach • 211⁄2" Length

• 1/2" Gap. • 201⁄2" lbs.No.151PU..............................

HAND RIVET SQUEEZERS

“C” YOKES FOR SQUEEZERS

ALL MODELS DESIGNED TO SQUEEZE 1/16” THROUGH 3/16” ALUMINUM RIVETS,COMPLETE WITH ADJUSTABLE RIVET SET HOLDER WHICH ALLOWS ADJUSTMENT FOR

VARIOUS RIVET LENGTHS. HARDENED STAINLESS STEEL “C” YOKE AND FRAME.SEE PAGES 7, 8, AND 9 FOR .187 SHANK TOOLING.100% Stainless Steel Replacement Yoke OnlyTHS 15 . . . . . .1-1/2” Reach x 1-1/4” Gap THY 15 . . . . . . . . . . THS 20 . . . . . .2” Reach x 1-1/4” Gap THY 20 . . . . . . . . . .THS 22 . . . . . .2” Reach x 2” Gap THY 22 . . . . . . . . . .THS 30 . . . . . .3” Reach x 1-1/4” Gap THY 30 . . . . . . . . . .THS 40 . . . . . .4” Reach x 1-1/4” Gap THY 40 . . . . . . . . . .THS 60 . . . . . .6” Reach x 1-1/4” Gap THY 60 . . . . . . . . . .THS 30-4 . . . . With 2” and 3” Yoke

HEAVY DUTY, 360” Swivel YokeDevelops 3,500 lbs. of pressure* DA 2 . . . . . . . .2-1/2” Reach x 1-5/8” Gap* DA 5 . . . . . . . .6” Reach x 1-5/8” GapOverall Length 18-1/2” Weight 9 lbs.

*NOTE: Requires 1 set threadedadapters to use std. 3/16” shanktooling #3824- ...........per set

HAND RIVET SQUEEZER AT501A Manufactured with jaws of heat treated toolsteel. The deep throat with 18” handles providesample leverage for ease of operation. 2-1/2”Yoke reach uses .187 shank sets.

“C” YOKES TO FIT#US114 & #CP214 CENEL

(#3000C, 6000C)APT 705, 720

1-1/2” Reach x 1-1/4” Gap . . . . . . . . . . . . . . .60,0001-1/2” Reach x 2-1/2” Gap . . . . . . . . . . . . . . .60,012

1-1/2” Reach x 3” Gap . . . . . . . . . . . . . . .60,0132” Reach x 1-1/2” Gap . . . . . . . . . . . . . . .60,001

2-1/2” Reach x 1-3/8” Gap . . . . . . . . . . . . . . .60,0023” Reach x 1-1/2” Gap . . . . . . . . . . . . . . .60,014

2” Reach x 2” Gap . . . . . . . . . . . . .60,003 TD1-1/2” Reach x 1-1/4” Gap . . . . . . . . . . . .60,010 TD

1-1/2” Reach x 3” Gap . . . . . . . . . . . .60,011 TD4” Reach x 2” Gap . . . . . . . . . . . .60,009 TD

4” Reach x 1-3/4” Gap . . . . . . . . . . . . . . .60,0075-1/2” Reach x 1-3/4” Gap . . . . . . . . . . . . . . .60,008

2-1/8” Reach x 1-3/16” Gap . . . . . . . . . . . . . . .90.0132-1/8” Reach x 1-1/4” Gap . . . . . . . . . . . . . . .90,0143-3/4” Reach x 1-1/4” Gap . . . . . . . . . . . . . . .90,015

3-5/16” Reach x 3” Gap . . . . . . . . . . . . . . .90,0165” Reach x 2-1/2” Gap . . . . . . . . . . . . . . . .90,017

HEAVY DUTY MODELS3/4” THICK

6000C, APT 720C, ETC.

ADJUSTABLE DOLLIE YOKESTO FIT US114, CP214

3000C, 6000C, APT705, 720COMPLETE WITH DOLLIE &

LOCK NUT 3/4” THICK

“DEEP THROAT MODEL”3/4” THICK

6000C,APT720C, 114TC

“C” YOKES TO FIT#US151 & #CP0351 CUDELCOMPRESSION RIVETERS

SPECIFY #1 or #2AYOKE FRAME

YOKES MANUFACTURED TO MEET YOUR SPECIAL REQUIREMENTS

2” Reach x 2” Gap . . . . . . . . . . . . . . . 60,0032-1/2” Reach x 2” Gap . . . . . . . . . . . . . . . 60,0063” Reach x 1-1/2” Gap . . . . . . . . . . . . . . .60,004

3-1/2” Reach x 1-1/2” Gap . . . . . . . . . . . . . . .60,0053/4” Thick

REMOVABLEYOKE TYPE

3

BENCH MODEL RIVETERS

SIOUX HIGH POWER RIVET SQUEEZERS

4

The new SIOUX™ Triple Cylinder offers up to9000 lbs. of compression force. Will easilysqueeze up to 1/4” diameter aluminum rivets. 18-3/4” long, weighs only 8-1/2 lbs. Acceptsindustry standard 3/16” rivet squeezer sets. Unit can be fitted with longer reach jaws. Jaw has 1-1/2” reach with a 1-1/4” gap. MODEL SZEA8015

DEEP THROAT RIVETERS* SUITABLE FOR

AIRCRAFT

BRAKE RIVETS

* ALSO AVAILABLE AS FLOOR MODELS

Shown withStandard 3”Reach Yoke, x 1-3/4” Gap.

5

COMPRESSION UNIT DEVELOPS 0-8800 LBS MAXIMUM COMPRESSION FORCE WITH LINEPRESSURE OF 90-100 PSI

*12-1/2 IN. REACHGap 3-1/2 IN.AVAILABLE

*REACH 9-1/2 IN.Gap 3-1/2 IN.

FLANGER

STANDARD TOOLING BAR

3/16 IN. SHANK SQUEEZER SET

SPECIAL TOOLING BAR

FOOT CONTROL (FC-2)

ADJUSTABLE MANDREL FOR 3/16IN SHANKSTANDARD AIRCRAFT SQUEEZER SET

OPTIONAL EQUIPMENT FOR PRESS INHARDWARE FOR 6000 CSA AND 8000 CSA

• 2— 4 — 6 — 8 — 10 in. studs• (4-40 6-32) — (6-32 8-32) — (10-32) standoff• (2-4) — 6-8-) — 10 threaded inserts• (4-40) — (6-32 8-32) — (10-32) floating nuts

“SET A” INCLUDES 15 PIECES FOR GETTING IN CLOSE:

• stud button holder• 2— 4 — 6 — 8 — 10 — 1/4 long stud buttons• (2-4) — 6-8-) — 10 long standoff buttons• (2-4) — 6-8-) — 10 threaded inserts• (2-4) — 6-8-) — 10 floating nuts

For 1/2 in. in length or less

For 1/2 in.and up to1-1/2 in. in length

“SET B” INCLUDES 15 PIECES

DEEP THROAT RIVETERS AND DIMPLERS

GOODYEAR/LORAL AEROSPACE CORPORATION BRAKE RIVETING TOOLS

PNEUMATIC SQUEEZERS

We have a complete selection of tooling for the installation of Goodyear/Loral™ aircraft brakes. Most of thelisted tools are designed with .312 shank diameter to fit the Model 150 Riveter or the Chicago Pneumatic450 Riveter. These tools are manufactured in strict accordance with Goodyear/Loral™ standards.

REBUILTS

AVAILABLE

Rivet Capacity Steel (DIAM.)

3/8” 16,0008”12”24”36”

190 lbs.230 lbs.475 lbs.

2000 lbs.

48”52”57”65”

3-1/4”3-1/4”5”8-1/2”

Yoke Sizes Reach Gap

Max. Force LBS. @ 90 P.S.I. Weight Height

114-139-1114-151-15T1-250925T1-252865T1-25287

5T1-253095T1-253105T1-253115T1-253555T1-25453

5T1-254555T1-254605T1-25465-15T1-25465-25T1-25470

5T1-257755T1-258075T1-258555T1-260375T1-26123

5T1-261505T1-262065T1-262455T1-709485T1-71785

5T2-100665T2-100675T2-100685T2-100735T2-10080

5T2-101575T2-104315T2-59945T1-1/4 Deriveting Punch5T1 Deriveting Anvil

6

“C” Yoke TypeThese lightweight, sturdy, compactand fast pneumatic squeezers have an aluminum rivet capacity of 1/8”(3.18mm) for DS-C28-20 and 3/16”(4.8mm) for DS-C44-24 when operating at 90psi. air pressure.

Rivet set holder adjustment –.2”(5mm) for use with different thicknesses without rivet set change.

Safety throttle lever with featheredmovement for fast or slow approach.

ModelNumber

Jaw SpecificationsPounds Max. Force @ 90 PSI(6.2 bar)

Max. Travel

in. mm

Overall Length

in. mmReach

in. mmWeightlb kg

Gapin. mm

Snap HolderAdjustment

in. mm

DS-C28-20 3000 1.38 35 .12 3 1.97 50 1.41 36 10.78 274 4.8 2.16

DS-C44-20 4850 1.34 34 .12 3 1.97 50 1.38 35 13.4 340 6.7 3.04

ALSO AVAILABLE: FLOOR MODEL 15KCSA-24” (F.O.B. FACTORY)

This Air Operated Pedestal Compression Riveter will easily compress 3/8” dia.Steel rivets, developing in excess of 16,000 max, force @90 P.S.I. The valving in our unit allows for greater control than comparable riveters of other manufacturers.It comes complete with stand and air operated foot control. This Rivet Machine has been designed with the cooperation and assistance of the Goodyear Corp., and is recommended for repair of Goodyear brakes on many aircraft.

Model 150150-8” Reach150-12” Reach150-24” Reach150-36” Reach

DS-C44-20

DS-C28-20

CUPPED SQUEEZER SETS

7

*Quantity *Quantity *Quantity *Quantity

NOTE: * QUANTITY PRICE BREAKS AS SHOWN ABOVE

FLUSH SQUEEZER SETS

24 Pcs. of soft and hardened flush sets all in 1 box. Plus shims.#24 RSK

26 Pcs. of the most popular sets all in 1 box. (AN 470, Flush,AN 450, AN 430, 1/16-3/16 dia.plus shims). .187 shank.#26 RSK

4502

4503

4504

4505

4506

4508

*45010

PRICE 1-24

PRICE 25-99

PRICE 100-up

8

DIMPLE TOOLS FOR AN–426 RIVETS & AN–509 Screws

TO ORDER: Specify Part No. followed by Symbols for Shank and Body Length Desired.EXAMPLE: To Order 3/32 AN-426, .187 Shank, 3/8 length, PunchSPECIFY: STM 4263 A–2TO ORDER IN PAIRS, SPECIFY AS FOLLOWS–EXAMPLE: STMF 4263 A-2. (INCLUDES MALE & FEMALE 3/32” DIMPLE DIES, 3/8” L.)

SWIVEL DIMPLING TOOLS MS-20426 (AN-426)

AN509SCREW

9

AIRCRAFT RIVETING HAMMERS WITH TRIGGER CONTROL

10

Cleco®

F Series RivetersFor driving 1/8”-1/4” (3-6mm) rivetsStandard beehive retainerBuilt-in air regulator controls power outputSpool valve for precise speed control

Model Number

Bee Hive Retainer

F2-PT-RT-BF4-PT-RT-B

0.58 140.58 14

2.0 52 4.0 102

.401 10.2

.401 10.26.7 1708.7 222

2.7 1.23.3 1.5

39001700

F Series Riveters – Round Taper Nose – Pistol Grip

Bore

in. mm

Stroke

in. mm

Length

in. mm

Weight

in. mm

For Use With RivetSet Shank Dia.

in. mmBlows Per

Minute

Blows Per

Minute

2000

2500

1700

overallLength

ins.

6-3/4

5-3/4

7-3/4

Net. Wt.Tool OnlyLbs. Oz.

3-3

3-0

3-8

Inter-changeable

with

AVC 12

AVC 11

AVC 13

Capacity

3/16” steel rivet

5/32” steel rivet

1/4” steel rivet

Cat.No.

270 A-1

270 A-2

270 A-4

StrokeIns.

3

2

4

EXCELLENT FOR RIVETING, TEASINGTHROTTLE, ALUMINUM HANDLE,

.401 SHANK

F2-PT-RT F4-PT-RT

TYPE 3XPB

TYPE 4XPB

.401 3/16” 5/32”

.401 1/4” 3/16”

2–7/8” 7–7/8” 2

3–1/16” 8–7/8” 2–1/2

2–7/8” 7–5/16” 2– 5/16

3–1/16” 8–5/16” 2– 3/4

2–1/4” 6–11/16” 2–1/4.401 1/8” 3/32”

Equivalent To: CP–4444–RURAB

.401 3/16” 5/32”

Equivalent To: CP–4444–RUSAB

.401 1/4” 3/16”

Equivalent To: CP–4444–RUTAB

.498 1/4” 1/4”

.498 3/8” 5/16”

.498 5/16” 1/4”Equivalent To: CP–4447–RU SERIES

2–11/16” 8–15/16” 4–3/45–13/16” 11–15/16” 63–7/8” 9–15/16” 5–1/8

TYPE 2X

TYPE 3X

TYPE 4X

TYPE

5X, 7X, 9X

SHANK SIZE

STROKE LGTH WGT(lbs.)

RIVETALUM.

CAPACITYSTEEL

AIRCRAFT RIVETING HAMMERS WITH TRIGGER CONTROL

SUPER SHORTIES SEE PAGES 15&16 FOR RIVET SETS

INGERSOLL- RAND L IGHTWEIGHT RIVETERS

11

AV C 1 3 A 1

NEEDLE SCALERS AIR HAMMERS

For driving 1/8”– 3/8” (3-10 mm) rivetsFeatures:* Accurate and EASILY controlled tease throttle* Standard beehive retainer – allows use of a

wide variety of accessories* Built-in power regulators on A1 & B1 Models –

operator can change power on the job – no downtime!

Model Cold Rivet Capacity Diameter Length Weight Blows For Use With

Dural & Less Less Piston per Rivet Set Shank

Aluminum Soft Iron Handle Accessory Accessory Stroke Minute Bore Diameter CFM

in. mm in. mm in. mm in. mm in. mm in. mm in.

Industrial/Aerospace

FP10604–3/4 lbs.19 Needles – 5” LongIn de-rusting and cleaning of metals, peening of welded joints, cleaning of hardened concrete from construction equipment, the FP-1060 NeedleScaler offers versatility for working in confined space or contoured surface with low air consumption. The needles adapt themselves to anycurved or uneven surface.

EXTRA NEEDLE NO.109130 ____________

CP711STANDARD DUTY.401 Shank3-1/2lbsLength 6-3/4”3500 BPM

CP715HEAVY DUTY.401 Shank4-1/2 lbs.Length 9”2100 BPM

.401 5/32” 1/8” 1-7/8” 4” 2-1/8”Jiffy

.401 5/32” 1/8” 1-7/8” 3-5/8” 2-1/4”Jiffy

.401 3/16” 5/32” 2-1/4” 5-3/8” 3-1/4”Jiffy

EXPERT REPAIRS

ON ALL BRANDS

TYPE 1X(SHORTIES)

100B200B

AVC10A1

SHANK SIZE

RIVETALUM.

CAPACITYSTEEL

STROKE LGTH. WGT.(lbs.

OTHER NEW AND REBUILT MODELS AVAILABLE

AVC10A1 1/8 3 1/8 3 Pistol 6 152 2-3/16 1.28 1-7/8 48 3200 9/16 14 .401 12

AVC10C1 1/8 3 1/8 3 Straight 6-25/32 172 2-1/16 .94 1-7/8 48 3200 9/16 14 .401 12

AVC12A 3/16 5 3/16 5 Pistol 7-3/4 197 3-3/8 1.53 3 76 2100 9/16 14 .401 13

AVC13A1 1/4 6 1/4 6 Pistol 8-3/4 222 3-11/16 1.67 4 101 1725 9/16 14 .401 13

AVC26A1 3/8 10 5/16 8 Pistol 11- 5/16 287 5-1/8 2.32 6 152 1120 3/4 19 .498 14

AVC26B1 3/8 10 5/16 8 Goose 13-15/16 354 7 3.18 6 152 1120 3/4 19 .498 14Neck

.498 3/8” 5/16” 6” 13-15/16” 7 lbs.AVC26B1

FITS MODELS 2X, 3X, 4X, CLECO “E” SERIES

AIR HAMMER ACCESSORIES

NO. 5210BEE HIVESPRING

NO. 5120QUICK CHANGE

RETAINER

RH – 3RB – 3

FITS MODEL AVC

RB – 4RH – 4

FITS MODELS5X, 7X, 9X

NO. 5130SAFETY CHUCKCHISEL HOLDER

SWIVEL POWER REGULATOR#94407 – COMPOSITE

12

AIR HAMMER ACCESSORIES

RIVET FAN SPACING TOOL

RIVET SETS

SHANK ADAPTERS

13

PART NO.

F501

TYPE

STANDARD

No. OF FINGERS

20

SPACING RANGE

1/2” (13mm) Closedto 2” (51 mm) Open

Overall Length (open)

38” (97 cm)

The RIVET SPACING TOOL is used to line up rivet holes. Simply expand or contract the fan,the accordion action gives you the spacing you need to set holes with precise accuracy.

* LAYOUT AND MARK EQUALLY SPACED HOLES* CLEVER ACCORDION GATE STYLE* UNEQUALLED FOR SPEED & ACCURACY

2-1/2”

USE WITH NO.1040 & NO. 1042 90º RIVETING ATTACHMENTS

TO ORDER — SPECIFYPART NUMBER, RIVET SIZEEXAMPLE NO. 1173 - 4704 FOR 1/8” CUP

STRAIGHT RIVET SETS CUPPED 1/16” THRU 1/4”

10º OFFSET RIVET SETS CUPPED 1/16” thru 1/4”

(Note: Specify SM30- Series For .498 Shank Ex: SM30-4708 for 1/4” AN470 Set)

(Note: Specify SM40- Series For .498 Shank

10º

L

.401

L

.401

14

10SP802

10SP852

10SP1572

10SP803

10SP853

10SP1573

10SP804

10SP854

10SP1574

10SP805

10SP855

10SP1575

10SP806

10SP856

10SP1576

10SP808

10SP858

10SP1578

20SP802

20SP852

20SP1572

20SP803

20SP853

20SP1573

20SP804

20SP854

20SP1574

20SP805

20SP855

20SP1575

20SP806

20SP856

20SP1576

20SP808

20SP858

20SP1578

“AS” AVAILABLEON REQUEST

“AS” AVAILABLEON REQUEST

RIVET SETS FOR BOEING BACR 15 FT

STRAIGHT BELL RIVET SETS

JIFFY SETS SERIES “B”

MODIFIED UNIVERSAL

MODIFIED UNIVERSAL

BOEING CUPPING

AN470BAC

STRAIGHT RIVET SIZE AND PART NUMBER

5/32104705BAC

3/16104706BAC

7/32104707BAC

1/4104708BAC

9/32104709BAC

MODIFIED UNIVERSAL

BOEING CUPPING

AN470BAC

OFFSET RIVET SIZE AND PART NUMBER

5/32204705BAC

3/16204706BAC

7/32204707BAC

1/4204708BAC

9/32204709BAC

L = 3 1/2

TO ORDER: SPECIFY PART NUMBER AND DESIRED LENGTH

1/4” – 5/16” – 3/8”

BRITISH STYLE CUPPING

1/4 5/16 3/8UNIVERSAL AN-470 SM5047010 SM5047012ROUND AN-430 SM5043010 SM5043012FLAT(CUPPED) AN-442 SM5044210 SM5044212BRAZIER AN-455 SM 504558 SM5045510 SM5045512MOD. BRAZIER AN-456 SM5045610 SM5045612

RIVET HEAD CUPPING RIVET SIZE AND PART NUMBER

Round/SNAP SP80* SP808 SP8010 SP8012

MUSH SP85* SP858 SP8510 SP8512

SP157* SP1578 SP15710 SP15712

LENGTH (L)

3-1/25-1/27-1/210-1/2

PRICE1-5

NOTE: AVAILABLE 10º OFFSET, SPECIFY SM60, FOR .498 SHANK, SPECIFY SM70

TO ORDER: SPECIFY PART NUMBER AND DESIRED LENGTH (“L”)

FOR USE WITH MODELS 1X,100B AND 200B RIVET GUNS

JIFFYSERIES “B”

FLUSH SETS

Part No. “A” Shank “S” Length “L” Price

SMJ500 3/8 .401 1-3/16

SMJ501 1/2 .401 1-3/16

SMJ502 5/8 .401 1-3/16

Jiffy Series “B”

Cupped Sets

Rivet Size 3/32 1/8 5/32 3/16 1/4 PriceUniversal AN470 4703 4704 4705 4706 4708

EXAMPLES: To Order– .401 – 5/32 AN470 – Straight, Specify SMJ510-4705

*A.S. AVAILABLE ON REQUEST

*A.S. AVAILABLE ON REQUEST

BRITISH STYLE CUPPINGRound/SNAP SP80* SP803 SP804 SP805 SP806 SP808

MUSH SP85* SP853 SP854 SP855 SP856 SP858

SP157 SP1573 SP1574 SP1575 SP1576 SP1578

STRAIGHTSMJ510*–

OFFSETSMJ520–

15

RIVET SETS FOR USE WITH JIFFY SERIES “B” TYPE RIVETERS

16

TO ORDER: Specify Part Number and desired Rivet Head CuppingEXAMPLE: To order 3/16 AN-470 for .401 type Shank, 7 /2” long-SPECIFY: SM131-4706

DOUBLE OFFSET CUPPED RIVET SETS

SM130 SM131 SM132 SM133

STG01STG02

GOOSENECKRIVET SETS

TRANSFERPUNCHES

TO ORDER: Specify Part Number and desired Rivet Head CuppingEXAMPLE: To order 3/32 AN-470 for .401 Shank – Specify ST G01-4703

Part NumberSMDP (Dash No.)

17

.401 SHANK STRAIGHT TUBULAR RIVET SETS (AN-450)

18

SM104502

SM104503

SM104504

SM104505

SM104506

SM104508

3-1/2” LENGTH

SEE PAGE 93FOR ROTARYREMOVALCUTTERS

* SPECIAL

TO ORDER: Specify Part No.

EXAMPLE: To order .401 Shank1/8 AN-450Specify: SM 104504

SMHSC401-4SMHSC401-5SMHSC401-6SMHSC401-8SMHSC401-10SMHSC401-12

1/85/323/161/45/163/8

AT106A FLUSH SET, SWIVEL–TYPE

FLUSH SETS

Performs high-speed flush riveting on flat or curved surfaces and isdesigned for ease of handling, with a swivel action to producequick alignment. The highly polished rivet set head is enclosed in arubber sleeve and can be easily hand assembled or disassembled.

19

SHANK DIA.A .401B .498

CUT-A-WAY VIEW

STRAIGHT FLUSH SETS“B.D.” (BODY DIAMETER)

3/81/25/8

STRAIGHTPART NUMBER

1037510500 10625

OFFSET PART NO.

20375 20500 20625

Specify Part Number and desired “L” Dimensions (Length)

LENGTH2-1/2”3-1/2”5-1/2”7-1/2”10-1/2”

Note: Add “B” afterPart No. for 498 Shank.

STRAIGHT FLUSH SETS(MUSHROOM)

.401 SHANK

10o OFFSET FLUSH SETS(MUSHROOM)

.401 SHANK

.498 SHANK

.498 SHANK

MM151-1 MM170-1

SM90 SM91 SM92 SM93 SM94 SM95 SM96 SM97 SM98 SM99

MM151-1BMM170-1B

SM100 SM101 SM102 SM103 SM104 SM105 SM106 SM107 SM108 SM109

2-1/83-1/22-1/2

35-1/27-1/2

35-1/2

33

2-1/82-1/4

3/43/41111

1-1/41-1/41-1/21-3/41-1/81-1/4

2-1/83-1/22-1/2

35-1/27-1/2

35-1/2

33

2-1/82-1/4

3/43/41111

1-1/41-1/41-1/21-3/41-1/81-1/4

PRICE PRICE

SM140SM141SM142SM143SM144SM145

SM160SM161SM162SM163SM164SM165

3-1/25-1/27-1/23-1/25-1/27-1/2

3-1/25-1/27-1/23-1/25-1/27-1/2

111

1-1/41-1/41-1/4

111

1-1/41-1/41-1/4

PART NO. PART NO.LENGTH (L) LENGTH (L)DIA (D)

PRICEPART NO. LENGTH (L) DIA (D) PRICEPART NO. LENGTH (L) DIA (D)

DIA (D)

NOTE: QUANTITY DISCOUNTS (6, 25, 50,100)

WHEN ORDERINGSPECIFY: BASIC PART NO. SHANK DIA. LETTER

EXAMPLE: AT 106A

20

D

2-1/2” Approx.

1-3/4” to 2-1/8

D

D

S

3”

FLUSH SWIVEL SETS

SHORT FLUSH SETSWITH SPRING GROOVE

Flush Sets with Aluminum or Brass Face

FLUSH (MUSHROOM) SETS WITH RUBBER GUARD

FACE DIA. (D) 3/4 1-3/16PART NO. SM180 SM181PRICE

PART NO.

SM170

SM171

SM172

SM173

SM174

SM175

SM170-2

SM171-2

SM172-2

SHANK(S)

.401

.401

.401

.498

.498

.498

DIA(D)

3/4

1

1-1/4

3/4

1

1-1/4

3/4

1

1-1/4

PRICE

REPLACEMENT

RUBBER

GUARD

.401 or .498 Diameter

SHANK

1” FACE

3-1/2”

PART NO.MM151-1MM151-2MM151-3MM151-4

PRICEDIA (D)

3/41

1-1/41-1/2

.401 SHANK (S) PART NO.MM151-1BMM151-2BMM151-3BMM151-4B

PRICEDIA (D)

3/41

1-1/41-1/2

.498 SHANK (S)

Part No.

SM50-1A

SM70-1A

SM50-1B

SM70-1B

Shank

.401

.498

.401

.498

Head

ALUM.

ALUM.

BRASS

BRASS

21

NOTE. QUANTITY DISCOUNTS – 6, 25, 50, 100 each

HIGH SHEARSTRAIGHT SETS1/8” thru 1/4”

HIGH SHEAR100 OFFSET SETS1/8” thru 1/4”

HIGH SHEARSTRAIGHT SETS5/16” thru 3/8”

PRICE .401 SHANK .498 SHANK PRICE1-5 PART NO. LENGTH (L) PART NO. LENGTH (L)

SMHS10- 3-1/2 SMHS30- 3-1/2SMHS11- 5-1/2 SMHS31- 5-1/2SMHS12- 7-1/2 SMHS32- 7-1/2SMHS15- 2-3/4 SMHS35- 2-3/4

PRICE .401 SHANK .498 SHANK PRICEPART NO. LENGTH (L) PART NO. LENGTH (L)SMHS20- 3-1/2 SMHS40- 3-1/2SMHS21- 5-1/2 SMHS41- 5-1/2SMHS22- 7-1/2 SMHS42- 7-1/2

Made in 1/8, 3/16 and 1/4 Rivet Sizes TO ORDER: Specify Part No. followed by Rivet Size desired. EX: SMHS10-3/16TO ORDER: Sets for Stainless Steel or Monel Rivets add Letter “M” to Part No.

TO ORDER: Specify Part No. followed by Rivet Size DesiredTO ORDER: For Steel or Monel Rivets add Letter “M” to Part No.

PRICE .401 SHANK .498 SHANK PRICEPART NO. LENGTH (L) PART NO. LENGTH (L)SMHS50- 3-1/2 SMHS70- 3-1/2SMHS51- 5-1/2 SMHS71- 5-1/2SMHS52- 7-1/2 SMHS72- 7-1/2

22

RIVET SETS

TO ORDER STRAIGHT OR OFFSET HUCK SETS:

Specify Part No. and desired Rivet Size

EXAMPLE : To order 5 1/2” Offset for a 5/32 Bolt, .401 Shank –SPECIFY : SMH21-5/32

NOTE: QUANTITY DISCOUNTS (6, 25, 50,100 each)

STRAIGHT RIVET SETS for HUCK LOCKBOLTS

1/8” thru 3/16”

STRAIGHT RIVET SETS for HUCK LOCKBOLTS

1/4” – 5/16” – 3/8”

100 OFFSET RIVET SETSfor HUCK LOCKBOLTS

1/8” thru 3/16”

PART NO. LGTH (L)

SMH10 – 3-1/2SMH11 – 5-1/2SMH12 – 7-1/2SMH13 – 10-1/2SMH15 – 2-3/8

PART NO. LGTH (L)

SMH50 – 3-1/2SMH51 – 5-1/2SMH52 – 7-1/2SMH53 – 10-1/2

.401 SHANK

PART NO. LGTH (L)

SMH30 – 3-1/2SMH31 – 5-1/2SMH32 – 7-1/2SMH33 – 10-1/2SMH35 – 2-3/8

.498 SHANK

.401 SHANK

PART NO. LGTH (L)

SMH70 – 3-1/2SMH71 – 5-1/2SMH72 – 7-1/2SMH73 – 10-1/2

.498 SHANK

PART NO. LGTH (L)

SMH40 – 3-1/2SMH41 – 5-1/2SMH42 – 7-1/2SMH43 – 10-1/2

.498 SHANK

PART NO. LGTH (L)

SMH20 – 3-1/2SMH21 – 5-1/2SMH22 – 7-1/2SMH23 – 10-1/2

.401 SHANK

23

KNOCK-OUT PUNCHES

24

.401SHANKPART NO.

STK3STK4STK5STK6STK8STK10STK12

.498 SHANKPART NO.

STK3BSTK4BSTK5BSTK6BSTK8BSTK10BSTK12B

RIVET SIZE3/321/85/323/161/45/163/8

TO ORDER: Specify Part No. anddesired Length (L).

EXAMPLE: To Order .498 Shank for 3/16 Rivet, 5-1/2” Long–

SPECIFY: STK6Bx5-1/2

LGTH(L) 3-1/2 5-1/2

PRICE:

SPECIALKNOCK-OUT PUNCHES

(For High-Shear Rivets)

RIVET DIAM. 3/32 1/8 5/32 3/16 1/4 5/16 3/8PART NO STK3X STK4X STK5X STK6X STK8X STK10X STK12X

RIVET SET EXTENSION ADAPTER

If .498 Shank is desired – Specify, “B”

NOTE: .498 shank, add

PART NO..401 SHANK(S) ST401E

.401 or .498

BUCKING BARS

“WE QUOTE ON OTHER BARS” 25

6 1/4

2 3/42

#1112-3/4 LBS.

#112 (MM320-19)1-1/2 LBS.

#601M (MM320-4)6 LBS.

#634 (MM320-2)1LBS.

#638 (MM320-1)1-1/4 LBS.

#6462-1/4 LBS.

#6471-1/2 LBS.

#649 (MM320-32)2 LBS.

#653 (MM320-27)3 LBS.

#656 (MM320-12)1-1/4 LBS.

#669 (MM320-14)1-1/4 LBS.

#670 (MM320-5)1-3/4 LBS.

#676 (MM320-20)3/4 LBS.

#692 (MM320-39)3 LBS.

#715 (MM320-40)2 LBS.

#7361-3/4 LBS.

#7513-1/4 LBS.

#753.

#760B-21-1/4LBS.

#760B-101-1/4LBS.

AVIATION MAINTENANCE KITSINCLUDES THE FOLLOWING:1. Model 3X or 4X rivet hammer

with power regulator.2. #105 rivet set kit (5 pieces)3. #670 bucking bar4. #1300 rivet cutter5. #200 Cleco pliers

6. #K40 Cleco Pak (40 pieces)7. #KT84218, 3/8” air drill (2600 rpm)8. 6 assorted drill bits (#40, 30, 21, 11)9. Drill stops for above10. #17800 Polymer Resin Box with tote tray

VALUE:PART NO. 3XAMKPART NO. 4XAMK

INCLUDES THE FOLLOWING:1. Model 3X or 4X rivet hammer2. #1200 power regulator3. #670 bucking bar4. #751 bucking bar5. #K200 Cleco pliers6. 40 pcs. Clecos7. #KT84218, 3/8” drill8. 6 pcs. assorted drill bits (#40,30,21,11)9. 4 pcs. drill stops10. 105 rivet set kit (5 pcs.)11. #1300 rivet cutter12. #3K angle drill kit13. #330SK Micro countersink kit14. #19800 Polymer resin box with tote tray

VALUE: 3XMK................................... 4XMK...................................

FIVE PIECE RIVET SET PACKAGES

TEN-PIECE BUCKING BAR KIT

FIVE PIECE BUCKING BAR KIT(MOST POPULAR STYLES)

STRAIGHT RIVET SET MIX.401SHANK

NO. 105 3-1/2”L NO. 115 5-1/2”L

OFFSET RIVET SET MIX.401 SHANK

NO. 205 3-1/2”LNO. 215 5-1/2”L

3-1/2” LENGTHOR

5-1/2” LENGTH3/32” – 3/16”

UNIVERSAL (AN470), ANDFLUSH SET

#112 #638 #656 #669 #670

WE CANMAKE UPANY KITPER YOURREQUIREMENT

MASTER AVIATION KIT

#10BB.............................................

#112 #638 #656 #669 #670#692 #736 #751 #753 #760 B-2

#5BB.............................................

26

HYDRO-SHIFT CherryLOCK® RIVETERThe Cherry G784 Hydro-Shift Riveter is a pneumatic hydraulic tool designed for the mostefficient installation of nearly all diameters ofCherryLock Rivets up to 1/2” grip, (“A” GroupOnly), It can be operated in any position with onehand. With proper adapters & pulling heads, thistool can be used to install other types of rivets.See section below on “Pulling Heads” for correctpulling head & adapter part #s.HYDRO-SHIFT CherryLOCK Riveter KitNational Stock Number: 5130-00-935-4681

H690-4C/U -4 4 4 4 4 4 4H690-5C/U -5 4 4 4 4 4 4H690-6C/U -6 4 4 4 4 - -H690-8C/U -8 4 4 - - -

G784

G 784 PulIing Heads Pulling Heads are not furnished with the riveter and must be ordered separately.

H681 PULLING HEADThe H681 Series Pulling Head fits directly onto the toolto install both Bulbed and Standard CherryLOCK® Rivets.

RIVETDIA.

3/32”

1/4”

1/8”

5/32”

3/16”

DIMENSIONS

A BPULLING HEAD NUMBER

H681-3C Countersunk Head (MS 20426) .163 .332H681-4C Countersunk Head (MS 20426) .208 .341H681-4F Countersunk Head (1560) .430 .358H681-4S Countersunk Head (NAS 1097) .174 .341H681-B166-4 Uni-sink Head .250 .359H681-5C Countersunk Head (MS 20426) .269 .352H681-5F Countersunk Head (1560) .535 .338H681-5S Countersunk Head (NAS 1097) .225 .352H681-B166-5 Uni-Sink Head .313 .377H681-6C Countersunk Head (MS 20426) .335 .386H681-6F Countersunk Head (1560) .625 .367H681-6S Countersunk Head WAS 1097) .281 .386H681-B166-6 Uni-Sink Head .375 .419H681-8C Countersunk Head (MS 20426) .458 .398H681-8S Countersunk Read (NAS 1097) .374 .398

OTHER PULLING HEADS THAT WILL FIT THIS TOOL ARE SHOWN ON THE CHART BELOW

PULLINGHEAD

TYPE ADAPTER RIVETRIVETDIA.

MAXI-MUMGRIP

H9055-3 Straight 680B46 CherryLOCK “A” 3/32 ALLH9055-4 1/8 8,9*H9055-5 5/32 8,9*H9055-6 3/16 8,9*H9015-3C Straight 680B46 MS 3/32 ALLH9015-4C 1/8 ALLH9015-5C 5/32 ALLH9015-6C 3/16 ALLH9040-4C Straight 680B57 MS 1/8 ALLH9040-5C 5/32 ALLH9040-6C 3/16 ALLH9040-8C 1/4 ALLH642-4C40 Offset 680B57 CherryLOCK 1/8 8,9*H642-5C40 5/32 8,9*H642-6C40 3/16 8,9*H642-8C40 1/4 8,9*H680-B200A Straight CherryMAX 1/8, 5/32, 3/16 ALLH781-456 Offset 680B205 CherryMAX 1/8, 5/32, 3/16 ALLH753A-456 Right Angle 680B205 CherryMAX 1/8, 5/32, 3/16 ALL

*8 grip for protruding head, 9 grip for countersunk head.

SPECIFICATIONS FOR G784Air Pressure: 90 PSI (6.2bar) Min./110 PSI (7.6 bar) MaxStroke: 7/8 inch (22.2 m)Pulling Force: 2,600 lbs (11.57kN)@90 PSI (6.2bar)Weight: 8 lbs (3.63 kG)

EXPERT REPAIRS

ON ALL TYPE

CHERRY GUNS

H680B200A CherryMaxPulling Head

The H68OB200A Pulling Head is designed to enable theCherryLock Hydro-Shift riveting tools, such as G685S, G689,and G784 to install CherryMax Rivets.

H680B208 Pulling HeadFor 1/4” CherryMax Rivets

This Pulling Head attaches directly to the Cherry G784 orG689 Hydro-Shift Riveter for installation of 1/4” diameterCherryMax Rivets.

G-695B Right Angle CherryLOCK RiveterNational Stock Number: 5130-00-435-5689

The G695B Right Angle riveter is a pneumatic-hydraulic tooldesigned specifically for installing CherryLOCK® rivets in limited-access areas. The power unit rests on the floor and is connected to the right angle head unit with 8 feet of flexible hose. SPECIFICATIONS:Air Pressure: 90-110 PSIStroke: .625”Pulling Force: 2000 lbsWeight: 17 lbs

G695B Pulling HeadsPulling heads are not furnished with theriveter and must be ordered separately.

For Standard CherryLOCK® Rivets (NAS1398 & 1399)

27

Pulling Head

RivetDia.

Univ. Head

CR2163CR2263

Univ. Head

Univ. Head

Ctsk.Head

Ctsk.Head

Ctsk.Head

CR2162CR2262

CR2643CR2653CR2663

CR2642CR2652CR2662CR2563

MONEL STAINLESS STEELALUMINUM

CR2562

CHERRY LOCK RIVETERS

G30 Hand RiveterFor Installation of CherryLOCK® 'A' locked Spindle, rivets CR2672, & CR2673.National Stock Number: 5120-01-416-7826.

DESCRIPTIONThe Cherry® G30 Hand Riveter is an efficient, compact, lightweight and economical tool for installationof CherryLOCK® ‘A’ rivets. Provided with this tool is aspecial designed nose piece which is essential for theproper insertion of the rivet locking collar.To operate, insert the serrated stem of the rivet into thenosepiece. Insert the rivet into the application, holdingthe riveter nosepiece firmly and squarely against therivet head and squeeze the handles to install the rivet.On longer grip rivets, additional strokes will be required.

G30 riveter can pull the following rivets:

3/32 ‘A’ Code RivetsCR2672CR2673

NAS1399C3A( )NAS1398C3A( )

9.25”(234.9mm)

2”(50.8mm)

0.5”(12.7mm)

CHERRY® H782 PULLING HEAD

CherryMAX®

Blind Rivet ToolingRIVET PART NUMBER AND TOOL CROSS REFERENCE

All rivet part numbers listed below can be installedwith the Cherry power tools listed below.

The Cherry® brand H782 is a new universal, off-set pulling head capable of installing a broad variety of pull-type fasteners. Its strength, light weight and compact dimensions make it ideal for a diverse range of applicationsincluding restricted spaces.

VERSATILITY – A two-jaw offset pulling head capable of installing CherryMAX® rivets,CherryLOCK™ “A” code rivets, MaxiBolt™ “S” Type blind bolts, MBC® rivets, SPR®

rivets, NAS 1398 A & AB code products, MS90353/4, MS21140/1 “U” 05, NAS 1719,1720, & 1721 and pull-through type nut plate rivets by simply changing the threaded nosepieces. (see table for the complete list.)

ECONOMICAL – Use this pulling head inplace of straight and offset pulling headsand take advantage of the wide range ofnosepieces to save on additional pullingheads. Mounts directly on our CherryMAX®

power riveters including the lightweightG747, the long stroke G746A and our powerful G704B.

A NEW, MORE VERSATILE

PULLING HEAD FOR

AEROSPACE APLICATIONS

28

Part Number

782-456 (Included with H782)

782-6AL886-003 886-004 886-005 886-006 782-5BB

782-4MBC 782-5MBC 782-6MBC

782-3

Installs These FastenersCherryMAX® 4,5,6 Diameter

CherryMAX® AB 4,5,6 Diameter (Except -6 Diameter All Aluminum)

MBC® L/C 4,5,6 Diameter“S” Type Blindbolt -04,-05 Diameter

CherryMAX® AB -6 Diameter All AluminumCherryLOCK™ “A” Code -3 DiameterCherryLOCK™ “A” Code -4 DiameterCherryLOCK™ “A” Code -5 DiameterCherryLOCK™ “A” Code -6 Diameter

“U” Type Blindbolt -05 DiameterStandard MBC® -4 DiameterStandard MBC® -5 DiameterStandard MBC® -6 Diameter

Nut Plate Rivet & SPR® -3 Diameter

NOSEPIECE SELECTION CHART

Nosepieces Sold Separately

29

EXPERT REPAIRS

ON ALL TOOLS

This new compact power riveter weighsonly 3.625 pounds, yet has the power of much larger and heavier tools. TheG747 riveter installs –4, -5, and –6 CherryMax® rivets in all grips and materials. The lightweight and compactergonomic design greatly reduces operatorfatigue. The angled pulling head allowsinstalling rivets using a natural hand posi-tion for optimum comfort. This tool can be operated in any position with one hand,and offers a choice of straight, right angle,and offset pulling heads. STROKE: .437PULLING CAPACITY: 2100 lb. @ 90 psi

G747 POWER RIVETER

DESCRIPTIONThe Cherry G704B is a pneumatic-hydraulic tool designedspecifically for the most efficient installation of CherryMAX®rivets. Its durable, all metal housings makes this extremelyrobust tool ideal for use in rugged shop environments. This tool utilizes straight, offset and right-angle pulling heads, all ofwhich can install –4, -5, and –6 diameter CherryMAX® bulbtype rivets in all head styles, materials and grip lengths.Extensions are available for extending the pulling heads toreach limited access areas. See the section on pulling headsfor the correct pulling head part number. Weight: 4-1/4 pounds.

PULLING FORCE 3100 Pounds (13.79 kn) @ 90 PSI (6.2 bar)

G704B

G-27 HAND RIVETERThe Cherry G-27 Hand Riveter is designed specifically for the most efficientinstallation of 1/8”CherryMAXrivets.Overall length ofthe G-27 is 9-1/4”, thenet weight is just 13ounces and thepulling head is anintegral part of thetool. This compact,lightweight tool isalso available in arugged plastic caseas P/N:G27KIT.

CherryMAX® Power ToolNational Stock Number: 5130-01-393-1584

Military Part Number: M85188T2

This kit contains one each of the following items:

G747 Pneumatic-hydraulic Riveter

H701B-456 Straight Pulling Head for 1/8” to 3/16” Rivets/Parts List

H781-456 Offset Pulling Head for 1/8” to 3/16” Rivets/Parts List

H753A-456 Right Angle Pulling Head for 1/8” to 3/16” Rivets/Parts List

H747-3NPR Straight Pulling Head for Nut Plate 3/32” Rivets

700A77 Bleeder Bottle

269C3 Grip Gage

CA-22 CherryMAX Reference Card

Manual G747 Maintenance Manual

CA-07 CherryMAX Process Manual

P1393 Carrying Case

670A20 Stem Catcher Bag

G704B-SR3/16 CAP.

G747 & G704B

PULLING HEADS

Pulling Heads are not furnished with the riveterand must be ordered separately.

H753A-456 Right AngleNSN5130-01-393-2926

Military Part Number M85188S2

H701B-456 StraightNSN5130-01-393-2927


H781-456 OffsetNSN5130-01-393-2925lol


G704B RIVETER G747CMR LIGHTWEIGHTCHERRYMAX®

POWER TOOL KIT

1-3/4”

2-1/4”

3/8”

5-7/16”

3/4”

4-3/8”

1-7/16”

1-15/32”

11”(279.40 mm)

2-1/8”

(53.97 mm)

4-15/16”

(125.41 mm)

1-3/4”

(44.45 mm)

3/4” (19.05 mm)

CHERRYMAX RIVETERS

CHERRY® NUT-PLATE RIVETERS

30

G750A Lightweight Hand RiveterNational Stock Number: 5120-01-432-9361

DESCRIPTIONThe Cherry® G750A hand hydraulic riveting tool provides the versatility ofpneumatic-hydraulic riveter, but with the lightweight, high pull strength ratiodesirability not found in other hand riveters. The Cherry G750A has a unique2-stage hydraulic power cylinder that provides the user with the ease ofpulling the handle without the strain normally endured to install a highstrength fastener. This patentable 2-stage power feature allows the user tosqueeze the handle throughout the increase power requirement, withoutfeeling the need to squeeze harder to install the fastener. The Cherry® G750Ahand riveter can install a variety of blind fastener styles, diameters, headconfigurations, and material combinations. The G750A with the standardpulling head can install CherryMAX® and SST™ blind rivets in -4, -5, -6,diameters, and -05, -06 diameter MaxiBOLT blind bolts or threaded insertsby simply changing the pulling head. The straight pulling head is providedwith the tool.

SPECIFICATIONS FOR G750ASTROKE .750 inches (19.06 mm)PULLING FORCE 3800/4200 lb.WEIGHT 1.9 lbs. (861.8 grams)OVERALL HEIGHT 6.4 inches (162.5 mm)OVERALL LENGTH 7.75 inches (196.8 mm)PULLING HEADS Straight, Offset, Right Angle, Threaded inserts

G702A POWER RIVETERThe Cherry G702A – a pneumatic/hydraulic tooldesigned specifically for the most efficient installation ofCherry Nut-plate rivets. It weighs just over 3-1/2 lbs.,has a 3/4” stroke and a rated pull load of 1000 lbs. @90 psi air pressure at the tool.

The G702A Riveter operates on air pressure of 90 to 120psi. At 90 lbs. air pressure, the G702A does not exceed85dB(A) and consumes 2 cfm at 20 cycles per minute.

Pulling heads are not furnished with this tool. They mustbe ordered separately. Use a H702-3NPR pulling headwith the appropriate nosepiece:

NOSEPIECE PART NO.-3 DIA = 728A9-3-4 DIA = 728A9-104

G 29 HAND RIVETERThe Cherry G 29 Hand Riveter is a compact, lightweighttool for Installing Cherry Nut-plate rivets.

The G 29 is 9-1/4” long, weighs 13 oz. and has astroke of 5/16”.

The pulling head is an integral part of this tool andcomes equipped with a 728A9-3 nosepiece to install3/32” rivets. To install 1/8” rivets, replace the 728A9-3nosepiece with a 728A9-104 nosepiece which must beordered separately.

G750ACMR HAND RIVETER TOOL KITNSN5120–01-432-6190

G750A PULLING HEADSAND ACCESSORIESThe Cherry G750ACMR hydraulic rivetertool kit includes the G750A with a straightpulling head, adapter assembly, a rightangle pulling head, an offset pulling headand a sturdy plastic carrying case.

G750ACMR KIT CONTENTS

Item No. Qty. Part No. Description1 1 G750A Hand Riveter (includes Pulling Head)2 1 H781-456 Offset Pulling Head3 1 H753A–456 Right Angle Pulling Head4 1 75OA-088 Adapter Assembly5 1 TLIT H781-456 H781-456 Tool Sheet6 1 TLIT H753A–456 H753-456 Tool Sheet

G902 POWER RIVETER* Lightweight (only 2.0 lbs.)* Installs -3, 2.5mm, 3mm and -4 Nut-Plate Rivets.

Also -3 SPR and -3 CherryLock “A”.* Compact handle design

SPECIFICATIONSPULLING 550 lbs. @ 90 psi.CAPACITY: 730 lbs. @ 120 psi.

PULLING HEADSH902-3NPR(+) = 3/32” Nut -Plate H902-4NPR = 1/8” Nut-Plate (+) Replace nosepiece with 902–038 nose toinstall 3/32” CherryLock “A” Rivets.

H747-3NPRPulling Head

For use on: G747 , G746 and G704B to install Nut-Plate Rivets.

CHERRYMAX® RIVETERS

CHERRYMAX® RIVET TOOLING

CHERRYMAX® RIVETERS

31

Combinations of these extensions may be used to reach many restricted installation areas by increasing the overalllength of the puling head.

EXTENSIONS

704A12-2 (2”) NSN 5130-01-145-0206704A12-4 (4”) NSN 5130-01-145-0207704A12-6 (6”) NSN 5130-01-145-0208704A12-12 (12”) NSN 5130-01-178-0331

These extensions will fit directly on to the G747,G704B, G749A, G845A and G746 CherryMAX® Riveters and will accept any of the pulling heads listed for those riveters in the Tool Selection Chart on page 30.

753B21 (1-1/8”)

This extension increases the overall length of the H753A-456 right angle pulling head nosepiece to approximately 2-3/16”, enabling it to reach into more restricted areas.

Pneumatic PT 100R....

Cherry Max® (Note: The PT 100 R is not to be used forinstalling Cherrylock®Rivets which requireshifting tooling).

TOOL INCLUDES: 1/8, 5/32, 3/16, 1/4 CHERRYMAX NOSE TIP.

Rated pulling capacity (maximum) 3500 lbs.Power source: 90 to 130 PSIG air operated hydraulic pump assemblyStroke (maximum): .625”Weight (without air fitting): 29 oz.Sizes: 6” high, 6-3/4” Long, 1-7/8 wide

Cherry “A” max®

(thru –4 grip maximum)Cherry Nutplate Rivets F156Cherry Commercial Rivetsand Monobolts®

F187, AdapterF156, 3/32 Nose TipF168 3/16 MonoboltF169 1/4 MonoboltH749A-456 Straight HeadH781-456 Offset HeadH753A-456 R/Angle head

D 100 RN….Hand HydraulicD 100 RN KIT CONTAINS:D100 1 Rivet Tool.3/32 Nutplate Rivet Nosepiece1/8 Nosepiece for CherryMax

Universal Nosepiece for CherryMax (1/8, 5/32, 3/16) 6-32, 8-32, 10-32, 1/4-28 Pull-upStuds and driving anvils.

Nosepiece for any standard pop style rivet.

Plastic carrying case. 2-1/2 x 12-5/16 x 8-7/16)

Special Pulling Heads Available. See Above.

269C3 GRIP GAGE . . . . . . . . . . . . . . . . A simple, self–explanatory gage for determining material thickness and proper rivet grip length.

G 36 TYPE HAND RIVETER (#122)

THIS TOOL WILL HANDLE SOME CHERRY KNOB STEM, (MS) SERRATED, CHERRYLOCK OR CHERRYMAX RIVETS WITH APPROPRIATE PULLING HEAD.

PRICE NEW:(Less Pulling Head)

PULLING HEADS FOR SERRATEDCHERRYMAX,OR HUCK 9SP RIVETS

#121-1 –For 1/8”#121-2 –For 5/32”#121-3 –For 3/16”

#121-0 –For 3/32”

HANDNIPPER

For Flush Trimming Cherry RivetsNo. 209 . . . . . . . . . . . . . . . .

Special Pulling HeadsAvailable

Extended Straight CherryMax®

Right Angle CherryMax®

Offset CherryMax®Adapter

F187

For Use On Model G-36 (#122)

Or G715A Riveters

G87*

G87*

G87*

G87*

G87*

CHERRY LOCKBOLT TOOLS

32

A simple, self-explanatory gage for determining material thickness and proper lockbolt grip length.

EXTREME TREYRIVET ORGANIZER* 7”x1 2”x2” (Units are stackable)* 8 Compartments 3” wide x 2-7/8” long x

1-3/4” deep* Thermoplastic Rubber Construction

weighs .99 lb.* Drop-away handle for ease of

carrying and storingMODEL #ET-8

AIR BLEEDER

To keep CherryMax hydraulic tools operat-ing at peak efficiency, it’s essential thehydraulic system is kept full of fluid andfree of air. This Cherry Air Bleeder quicklyand easily removes all air assuring thecomplete filling of the tool with hydraulicfluid.

MODEL# 700A77 AIR BLEEDER NSN 5130-01-104-5372 For servicing all Cherry pneumatic/ hydraulic power riveters.

33

DOTCO® RIVET SHAVERS

SIOUX® RIVET SHAVERS

34

14CFS60-95 0.0005 29,000 2.3 1.0 8.2 210

14CFS60-98 0.00025 29,000 2.3 1.0 8.2 210

14CNL60-95 0.0005 20,000 4.5* 2.0* 8.9* 226*0.00025 20,000 4.5* 2.0* 8.9* 226*

14CF Series – Pistol Grip – 0.4 hp (0.30 kW) – with Stabilizer

14CF Series – Pistol Grip – 0.4 hp (0.30 kW) – without Stabilizer

14CN Series – Pistol Grip – 0.9 hp (0.67 kW) – with Stabilizer

Model Number Small Handle Large Handle

Weight lbs. kgs

Lengthin. mm

Cutter Adjustment

FreeSpeed rpm

*For weight and length of large handle models, add 0.20 lb.(0.1kg)GENERAL:Air Inlet: 1/4” NPT - Use 5/16” (7.9mm) I.D. HoseAll tools performance rated @ 90psi (620 kPa) air pressureSTANDARD EQUIPMENT: Stabilizer and choice of skirtEXTRA EQUIPMENT: Carbide Cutters & Extended Skirts: See table

No. 14CN

No. 14CF

5/16 – 14-4391 14-4401 – – – – – – – – –3/8 14-4382 14-4392 14-4402 – – 14-4532 14-4302 14-4312 14-4512 – 14-4372 14-45727/16 14-4383 14-4393 14-4403 14-4323 – 14-4533 14-4303 – 14-4513 14-4363 14-4373 14-45731/2 14-4384 14-4394 14-4404 14-4324 14-4334 14-4534 – – 14-4514 14-4364 14-4374 14-45749/16 14-4385 14-4395 14-4405 – – – – – – – – –5/8 14-4386 14-4396 14-4406 – – – 14-4306 14-4316 14-4516 – – –3/4 14-4387 14-4397 – – – – – – – – – –1 14-4422 14-4410 – – – – – – – – – –1-1/4 – 14-4412 – – – – – – – – – –

CutterDiameter

in. Carbide Cutter

Part NumberSkirts

Std. Wide 1” Extended Skirt

Adapter Skirt Assembly 4” Extended Skirt

Adapter Skirt Assembly 6” Extended Skirt

Adapter Skirt Assembly

Non-Reversible

No. RS9A-210-8 RIVET SHAVER Cuter capacity available up to 5/8”. Comes standard with 1/2” skirt. 18,000 RPM. This tool is designed for therapid and accurate removal of protruding rivet heads of countersunk rivets,leaving them perfectly flush with the surrounding surface. A micrometer typeadjustment is provided which enables the depth of the cutter to be altered byincrements of .0005”. 1/4-28 female threaded spindle takes standard cutters.

RS9A-210-8 (Pistol Handle).......................RS9AS-210-8 (Straight Handle).......................

No.RS9A-210-8Rivet Shaver

CARBIDE TIPPED CUTTERS

PART NO.800-1800-2800-3800-4800-5800-6

BODY. DIA5/163/87/161/29/165/8

15-20 Series

Nominal Motor Power

0.6 hp 0.45 kW

Non-ReversibleInline

Model NumberFree Speed

rpm

Weightlbs. kgs.

Lengthin.. mm.

Cutter

Adjustment

No. 15L2060-95

15-20 Series – Inline – 0.6 hp (0.45 kW) - with Stabilizer15L2060-95 0.0005 25,000 2.9 1.3 9.0 229

AUTHORIZED AEROSPACE TOOLING & SERVICE CENTER

35

HuckFastenersAlcoa Fastening Systems

REBUILTS

AVAILABLE

MODEL 956 POWER RIGHydaulic unitsOutput Pressure

Pull 8,400 PSI Return 3,500 PSI

HUCK PNEUDRALIC INSTALLATION TOOLS

36

M O D E L 2 0 0 P N E U D R A L I C I N S T A L L A T I O N T O O L

TOOL SPECIFICATIONS

M O D E L 2 0 2 5 P N E U D R A U L I C I N S T A L L A T I O N T O O LTOOL SPECIFICATIONS

M O D E L 2 0 6 - 3 7 5 H Y D R A U L I C I N S T A L L A T I O N T O O LTOOL SPECIFICATIONS

The Model 200 is designed to install fasteners requiringdouble action or single actioninstallation tooling. It provides a separate lock collar drivingfunction–the double action thatdrives the lock of blind rivet andblind bolt fasteners

The Model 200 is a productiontool that is easy to handle,and requires a minimum ofmaintenance. The lightweight

aluminum cylinder is steelsleeved, and to check reliability,factory tested for 2,000 cycles.

The power, speed, and accuracyof the model 200 are obtainedthrough a pneumatic-hydraulicintensifier system powered by90-100 psi air.

Models 206-375 and A206-375 arelightweight mini-tools that are easyto use and convenient for installingfasteners in limited clearance areas.Model 206-375 is a single actiontool with only one moving part,which keeps maintenance to a min-imum, and is designed to installHuck Blind Bolt Fasteners andHUCKBOLT® fasteners.

Each Model 206-375 is a cylinderand piston assembly with oneunloading value to relive hydraulicpressure at both ends of the stroke.

The design includes an offset piston for added tool clearance.A stop for anvil holder permits nose rotation to 80º.

Model 206-375 is equipped with a 12-foot hydraulic hose and electric control cord. The ModelA206-375 with an air trigger for use with the 956 POWERIG®Hydraulic Unit. Control tubing (pneumatic) with quick connects are provided for attachment to aPOWERIG® Hydraulic Unit.

The Model 2025, with nose assembliesnow available, installs the following:

Industrial Fasteners3/16 & 1/4 MAGNA-LOK®

3/16 & 1/4 MAGNA-BULB®

3/16 & 1/4 MAGNA-GRIP®

3/16 & 1/4 C6L®

Aerospace Fasteners3/16 & 1/4 MS90353/90354 Blind Bolt3/16 & 1/4 MS21140/21141 Blind Bolts1/4 NAS 1919/1921 Blind Rivets

The tool has features enabling it to install fasteners at high rates with minimum operator fatigue.

The 2025 tool’s features includes:

• In-line piston for one stroke installations

• Designed to install – 08 Steel MGFasteners @ 80 PSI

• Less than 5.8 lbs

• Ergonomically designed handle

• 360º swivel air inlet connection

• Noise level 75 DBA@ 90 PSI

SpecificationWeight:10.50lbs. (4.80 kg)

Air Pressure Required:90-100 psi (620-690 kPa)

Air Consumption18 CFM (0.009m 3/s) based on 30 fastener installations per minute

Hydraulic Fluid:Automatic Transmission Fluid DEXRON II® or equivalent

Stroke:1.19 in (30mm)

Specifications

Length (2025) 8.36 in. 212.34 mm

Width 1.81 in. 45.97 mm

Height 12.53 in. 318.26 mm

Center to edge .906 in. 23.01 mm

Weight 5.75 lbs 2.6 kg

Stroke 0.675 (nom.) 17.14 mm (nom.)

Pull capacity 5290 lbs. @ 90 psi.

Specification

Weight:3.37 lbs (1.50 kg)

Pull Pressure (max):5,400-5,700 psi(37,250-39,300 kPa)

Return Pressure (max):2,200-2,400 psi(15,200-16,000 kPa)

Stroke:Standard .375 in (9.52 mm)Optional: Tool stroke can be increasedto .50 in (12.7 mm) by removal ofstroke limitor. See instruction manual.

Note: This tool must be equipped with a nose assembly designed for the installationof a specific fastener. Nose assemblies mustbe ordered separately.



REBUILTS

AVAILABLE

Model 2025

Model 200

Model 206-375

Inches – Millimeters

Inches – Millimeters

1.7544

.62516

2.03 52

2.3159

HUCK PNEUDRALIC INSTALLATION TOOLS

37

REBUILTS

AVAILABLE

REBUILTS

AVAILABLE

M O D E L 2 4 5 P N E U D R A U L I C I N S T A L L A T I O N T O O L

TOOL SPECIFICATIONS

M O D E L 3 5 0 P N E U M A T I C I N S T A L L A T I O N T O O L

TOOL SPECIFICATIONS

M O D E L 3 5 2 P N E U M A T I C I N S T A L L A T I O N T O O L

TOOL SPECIFICATIONS

Model 245Inches – Millimeters



DOUBLE ACTION BLIND BOLT FASTENERS

ALUMINUM DOUBLE ACTION BLIND BOLT FASTENERSMODEL 200

MODEL 200

MODEL 350

MODEL 136

Includes part numbers:


3/16 diameter 5/32 diameter

38

UNIMATIC® SINGLE ACTION BLIND BOLT FASTENERSIncludes part numbers:

NAS 1919B( )S NAS 1921B( )SNAS 1919M( )S NAS 1921M( )SNAS 1919C( )S NAS 1921C( )SOSMLSP( ) OSMLS100( )SMLSP-BT SMLS100-BT

the Unimatic Blind Rivet fastener provides uniform bulbed head configuration regardlessof fasteners diameter or material, and ensures joint integrity and enhanced fatigue life.

Use Unimatic Blind Rivet fasteners in general design applications, in thin sheet stackups,thin blind side sheet, or thick stackups

Integrity an performance mean the Unimatic lock collar is trusted by designers even inmost demanding FOD critical applications such as high performance aircraft. The Unimatic Blind Rivet fastener in flush and protruding head styles

Model 244Type: Pneudralic

Applications: High-speed production

Features: Lightweight tool for fast,uniform installations. Optimum stroke for one cycle installation of fasteners to 1/4 diameter, heavy duty for years of dependable service. Minimum moving parts.



Features: Optimum stroke for onecycle installation of fasteners to 3/8diameter, heavy duty for years ofdependable service. Minimum moving parts.

Nose Assemblies1/8 5/32 3/16 1/499-2724 99-2730 99-2736 99-274299-2725 99-2731 99-2737 99-274399-2726 99-2732 99-2738 99-2744

Nose Assemblies1/8 5/32 3/16 1/499-27251 99-27311 99-27371 99-27431

99-15163 99-15172 99-15183 99-131199-17152 99-17162 99-17172 99-15193

99-1715-12 99-1716-12 99-1717-12 99-17182

99-1718-12


Applications: Medium production

Features: Lightweight tool for fast,uniform installations.

Nose Assemblies1/8 5/32 3/16 1/499-2724 99-2730 99-2736 99-274299-2725 99-2731 99-2737 99-274399-2726 99-2732 99-2738 99-2744

Model 206-375/A206-375Type: Hydraulic

Applications: Limited Clearance

Features: Uses offset nose assembly foradded clearance, and only one movingpart for minimum maintenance. Hosescan be repositioned

Nose Assemblies1/8 5/32 3/16 1/499-1715 99-1716 99-1717 99-171899-1715-1 99-1716-1 99-1717-1 99-1718-1

Model HK150-S456 / D100C–SPEC*Type: Manual

Applications: Field repairs

Features: Lightweight and easy to handle.Supplied as a complete kit including noseassemblies and driving anvils.

NOTE: The Model HK150 includes the S456 noseassembly, adapter part number 122587 and insertsfor 1/8, 5/32, and 3/16” fasteners.

1 Requires adapter part number 1024632 Requires adapter part number 119400 and

stroke limiter part number 183623 Requires adapter part number 117831 and

stroke limiter part number 118362

1/899-S456 with 111455 insert

5/3299-S456 with 111456 insert

5/3299-S456 with 111457 insert

Nose Assemblies

(*) Not a Huck Product 39

SHEAR PULL-TYPE HUCKBOLT® FASTENERSIncludes part numbers:

NAS 1446 - 1452 NAS 1436 - 1442NAS 7034 – 7042 NAS 7024 - 7032NAS 7014 – 7022 NAS 7004 – 7012NAS 2406V – 2412V NAS 2506V – 2512V

Designed for use in high-strength aerospace applications, the Huckbolt Fastenersis readily adaptable to high volume production methods. Common applicationsinclude primary airframes, main spars, and engine mounts.

There is a wide variety of collar configurations and materials not shown.The tooling shown in this section will install all NAS Shear pull-type lockbolts.

Note: These fasteners are available in stump type (without pintail) and are intended for hammer drive installation or automated installation. Contact Huck Installation equipmentDivision for information on hammer driving and tooling requirements.

Shear pull-type lock-bolt fasteners, flush and protruding heads

Collar for shear lockbolt fasteners



Features: Lightweight tool for fast, uniform installations.Optimum stroke for one cycle installation of fastenersto 1/4 diameter, heavy duty for years of dependableservice. Minimum moving parts.



Features: Optimum stroke for one cycle installationof fasteners to 3/8 diameter, heavy duty for years ofdependable service. Minimum moving parts.



Features: Optimum stroke for one cycle installation offasteners to 3/8 diameter, heavy duty for years ofdependable service. Minimum moving parts.



Features: Narrow centerline-to-edge measurementallows installations in limited clearance applications

Model 2503/A2503Type: Hydraulic


Features: Small, lightweight, with just one movingpart for increased reliability, and an offset pistonfor limited clearance. Archives the longest strokeavailable in this series of tooling

Nose Assemblies1/8 5/32 3/16 1/4 5/1699-2651 99-2548S 99-2554 99-2560

99-2549S 99-2555 99-256199-2550S 99-2556 99-2562

Nose Assemblies5/32 3/16 1/4 5/16 3/899-2551S 99-2557 99-2563 99-2566 99-2569 1

99-2552S 99-2558 99-2564 99-2567 99-25701

99-2553S 99-2558 99-2565 99-2567 99-25711

99-1703 2 99-1704 2 99-17052 99-1720 4

99-1703-1 2 99-1704-1 2 99-1705-1 2 99-1720-1 4

Nose Assemblies5/32 3/16 1/4 5/16 3/899-2551S 99-2557 99-2563 99-2566 99-256999-2552S 99-2558 99-2564 99-2567 99-257099-2553S 99-2558 99-2565 99-2568 99-2571

Nose Assemblies1/8 5/32 3/16 1/4 5/1699-614 99-2548S 99-2554 99-2560 1

99-2549S 99-2555 99-2561 1

99-2550S 99-2556 99-2562 1

Nose Assemblies5/32 3/16 1/4 5/16 3/899-2551S 99-2557 99-2563 99-2566 99-2569 1

99-2552S 99-2558 99-2564 99-2567 99-2570 1

99-2553S 99-2559 99-2565 99-2568 99-2571 1

NOTE: Nose assemblies shown in italic are available in chisel design–tapered flats for improvedcenterline to edge clearence. Specify by adding CH to part number, for example: 99-254TCH1 Aluminum material only2 Requires adapter part number 119400 and stroke limiter part number 1183623 Requires adapter part number 117831 and stroke limiter part number 1183624 Requires adapter part number 122134

1 “E” (Aluminum) material fasteners only

40

TENSION PULL-TYPE HUCKBOLT® FASTENERSIncludes part numbers:

NAS 1465 - 1472 NAS 1456 - 1462NAS 1525 - 1532 NAS 1535 - 1542NAS 6965 - 6972 NAS 1516 - 1522NAS 2005V - 2012V NAS 6955 - 6962NAS 6935 - 6942 NAS 6946 - 6952NAS 2125 - 2132 NAS 2115V - 2122VNAS 1475 - 1482 NAS 2105V - 2112V

Designed for use in high-strength aerospace applications, the HuckboltFasteners is readily adaptable to high volume production methods. Commonapplications include primary airframes, main spars, and engine mounts.

There is a wide variety of collar configurations and materials not shown. Thetooling shown in this section will install all NAS Tension pull-type lockbolts.

Note: These fasteners are available in Stump Type (without pintail) and areintended for hammer drive installation or automated installation.

Tension pull-type lock-bolt fasteners, flush and protruding headsCollar for tension lockbolt fasteners


Applications: Medium production

Features: Lightweight tool for fast,uniform installations.

Nose Assemblies5/32 3/16 1/4 5/16 3/899-2548T 99-2554 2 99-25601

99-2549T 99-2555 2 99-25611

99-2550T 99-2556 2 99-2562 1

Nose Assemblies5/32 3/16 1/4 5/16 3/8

706GP 708GP 710GP 712GP



Features: Optimum stroke for one cycleinstallation of fasteners to 3/8 diameter,heavy duty for years of dependable service.Minimum moving parts.


Applications: Limited clearance

Features: Built in nose assembly forconvenience and dependability, in anextremely small package.


Applications: High speed production

Features: Small, lightweight, with just one moving part for increasedreliabilty, and an offset piston for limited clearence.

Nose Assemblies5/32 3/16 1/4 5/16 3/899-2551T 99-2557 99-2563 99-2566 99-25691

99-2552T 99-2558 99-2564 99-2567 99-25701

99-2553T 99-2559 99-2565 99-2568 99-25711

99-1703 2 99-17043 99-1705 3 99-17204

99-1703-13 99-1704-1 3 99-1705-13 99-1720-14

99-1506 4 99-15084 99-15104

99-1507 4 99-15094 99-15114

99-15284 99-15304

Nose Assemblies5/32 3/16 1/4 5/16 3/899-2551T 99-2557 99-2563 99-2566 99-25691

99-2552T 99-2558 99-2564 99-2567 99-25701

99-2553T 99-2559 99-2565 99-2568 99-25711



Features: Narrow centerline-to-edgemeasurement allows installations in limited clearance applications

Nose Assemblies5/32 3/16 1/4 5/16 3/899-2548T 99-2554 3 99-25601

99-2549T 99-2555 3 99-25611

99-2550T 99-2556 3 99-25621

NOTE: Nose assemblies shown in italic are available in chisel design–tapered flats for improvedcenterline to edge clearence. Specify by adding CH to part number, for example: 99-254TCH1 Increase hydraulic unit pull pressure to 8400psi2 “E”(Aluminum material only3 Will not install DT alloy steel

NOTE: Nose assemblies shown in italic are available in chisel design–tapered flatsfor improved centerline to edge clearence. Specify by adding CH to part number, forexample: 99-254TCH

1 “E”(Aluminum material only2 Will not install DT alloy steel

3 Requires adapter part number 119400 and stroke limiter part number 1183624 Requires adapter part number 117831 and stroke limiter part number 1183625 Requires adapter part number 122134

41

FastenerDiameter

13/64” (06)17/64” (08)21/64” (10)

Hex Wrench SizePin Head

5/64”3/32”1/8”

Sleeve DriverPart Number

106524106525107735

Maximum Installation Torque(1)

20 Inch Pounds30 Inch Pounds40 Inch Pounds

ASP® Fasteners

42



Features: Lightweight tool for fast, uniforminstallations. Optimum stroke for one cycleinstallation of fasteners to 1/4 diameter,heavy duty for years of dependable service.Minimum moving parts.



Features: Optimum stroke for one cycleinstallation of fasteners to 5/16 diameter,heavy duty for years of dependable service.Minimum moving parts.



Features: Narrow centerline-to-edgemeasurement allows installations in limited clearance applications

Model 206-375/A206-375Type: Hydraulic

Applications: Limited clearance

Features: Uses offset nose assembly foradded clearance, and only one movingpart for minimum maintenance. Hosescan be repositioned.

Sleeve Installation Tools

Nose Assemblies13/64 (06) 17/64 (08) 21/64 (10)99-2642 99-2645 99-264899-2643 99-2646 99-2649 LONG LENGTH

Nose Assemblies13/64 (06) 17/64 (08) 21/64 (10)99-2642 99-2645 99-264899-2643 99-2646 99-2649 LONG LENGTH

Nose Assemblies13/64 (06) 17/64 (08) 21/64 (10)99-1728 99-1729 99-1730

1 Requires adapter part number 102463

2 Requires adapter part number 119400 and stroke limiter part number 118362

Nose Assemblies13/64(06) 17/64(08) 21/64(10)99-26421 99-26451 99-26481

99-26431 99-26461 99-26491 Long Length 99-17282 99-17292 99-17302


AspFF 2Asp509F & 509P

2AspFF & FP 2AspPF & PPThe Asp fastening system provides a simplified method of fastening composite, soft core,metallic, or other materials which are sensitive to fastener clamp-up or installation forceconsiderations. Clamping force can be infinitely adjusted and then sustained by installation– accommodating the unique requirements of a given structural design.

The Asp fastener has a positive mechanical lock for use in vibration and FOD criticalinstallations. It installs quickly and easily eliminating the need for potting, bushings,inserts, or step hole preparation. Asp fastener showing flush and protruding heads, sleeves, and lock collars

(1) Installation torque must be adjusted to determine the controlled clamping forcerequired for the soft core material being fastened. Over-torquing could result in damage to the material and installation sleeve driver.

BLIND RIVETERSM-4

HI SPEEDPNEUMATIC/HYDRAULICThis heavy-duty air/hydraulic riveter with its newly designed aluminumforged head can hold up under demanding, continuous use.The M-4 can set rivets from 3/32" thru 1/4" diameters in all alloys. The M-4 is supplied with 3/32. 5/32, and 1/4" standard nosepieces, service tools, swivel inlet air coupler and a mandrel collection bottle.85-95 PSI: Recommended air pressure Weight: 6.6 lbs

Optional Nose Pieces Available For Monobolts#95904...................3/16"#95906...................1/4”

BIG DADDY#39031

The "Big Daddy" is the most versatile and powerful Marson brand hand riveter,taking the hard work out of setting large diameter blind rivets. The "Big Daddy" features a double-gear reduction system whicheasily sets from 1/8" to 1/4" diameter Klik-Fast riv-ets in all alloys. A one-piece collet case eliminatesthe need to adjust the tool when changing rivetdiameters. The unit comes with 5/32, 3/16, and 1/4inch nosepieces which are stored in the body.Weight: 3.75 lbs

M– 3PNEUMATIC /HYDRAULIC

This heavy-duty air/hydraulic riveter. with its newlydesigned aluminum forged head can hold up underdemanding, continuous use. The M-3 will set blindrivets from 1/8" diameter in all alloys up to 3/16".Included are standard 1/8, 5/32 and 3/16" nose-pieces. 85-95 PSI: Recommended air pressure.Weight: 4.2 lbs.

200 KIT™

# 39001

The deluxe hand riveter kit includes HP-2and 200 assorted Klik-Fast rivets in popularsizes.The molded plastic case houses andprotects the tool, rivets and optional counter-sink double ended drill bit. Weight: 4 lbs.1/case

304-EAIR / HYDRAULIC

RIVETER

This is Marson's most powerful air/ hydraulicriveter, with its fully enclosed vacuum systemthat holds the rivet in the nosepiece, allowingthe operator to rivet at any angle with onehand free. The vacuum system automaticallycollects the spent mandrel into a bottle.Nosepieces to install 3/16 and 1/4 inch standard rivets are included. Also included are 3/16" and 1/4" Monobolts nosepieces.85-95 PSI: Recommended air pressure Weight: 5.5 lbs.

M3-VAIR /HYDRAULICThe M3–V is capable of setting blind rivets from 3/32" diameters in alloys up to 3/16".It has an internal vacuumsystem which allows the mandrel to be held in position while operating the tool at any angle.After setting, the spent mandrel is ejected into a mandrel collection bottle.85-95 PSI: Recommended air pressure Weight: 4.6 lbs.

HP-2 / #39000HAND RIVET TOOL

The HP-2 is the largest sellinghand rivet tool in the industry.Known and trusted for durability,quality and performance, high-strength aluminum body; drop-forged carbon steel upperhandle; and thick, cushion-molded vinyl grips for comfort.The HP-2 sets up to 3/16 steelrivets and comes with fourmounted nosepieces (3/32,1/8, 5/32, and 3/16 inch) and a service wrench.Weight: 1 lb., 3 oz.1/carton.

IL-1 #39070PNEUMATIC /HYDRAULIC

This durable in-line riveter with its fully adjustable vacuum system holdsthe rivet in the nosepiece in any riveting position and automatically ejectsthe mandrel into an attached container (not supplied). The IL-I is capable ofsetting rivet diameters from 3/32 " thru 3/16" in all alloys and easily hangsfrom any balancer – an ideal tool for assembly line riveting.85-95 PSI: Recommended air pressure Weight: 3 lbs.

ECONOMY MODELSPRI PNEUMATIC / AIRRIVETER KIT

This economy air riveter is the ideal tool for the shop.Kit comes complete with two adjusting wrenches toinstall with four assorted nozzles. Contains: Air rivet gun,3/32, 1/8, 5/32, and 3/16 inch nozzles and two open end wrenches.PR1– 3/16" CAP . . . . . . . .PR2– 1/4" CAP . . . . . . . .

EXPERT REPAIRS

ON ALL BRANDS

43

RIVET-NUT TOOLS

RIVET-NUT SPEED DRIVER KEYWAY NOTCH CUTTER

MANDREL / NOSEPIECE CHART For 39200, 34501 and 39202

Thread Size Mandrel No. Nosepiece No.

6-32 39254 392618-32 39255 39262

10-24 39256 3926310-32 39257 392631/4-20 39258 Not Needed5/16-18 39259 Not Needed3/8-16 39260 Not Needed4mm 39266 392745mm 39267 392736mm 39268 Not Needed

RIVET-NUTTER#39200This quality threaded insert installa-tion tool features patented bearingdesign, comfortable hand grips anda locking chain. The 39200 installsall sizes of Klik Poly-Nuts and KlikRivet-Nuts up to 1/4” and 6mmsteel. The tool is packaged in areusable, heavy-duty vinyl pouchcontaining mandrels and nosepieceto set 8-32, 10-24 and 10-32inserts. Weight: 1 lb. 3 oz.; 1/case.

HEAVY DUTYRIVET-NUTTER #325 RNChoose the 325RN forinstalling larger size threadedinserts. This is a heavy-dutytool that will install 10-24 thru3/8”–16, and 5mm thru10mm threaded inserts in alu-minum or steel. Supplied with1/4”–20 mandrel and nose-piece only. Weight: 4.25 lbs.

RIVET NUTTER TOTE KIT #34501Model 34501 Rivet Nutter Tote Kit contains the 39200 thread-setter tool in a molded plastic case; mandrels and nosepieces for 6-32, 8-32, 10-24 sizes, and a mandrel for 1/4-20. The kit also includes 103 assorted Klik Rivet-Nuts and Klik Poly-Nuts, instructionsand wrench, all contained in a compartmentalized carrying case. Weight: 2-3/4 lbs.; 1/case.NOTE: COMMERCIAL TYPE RIVNUTS

L845-WRENCH TYPE HEADERfor RIVNUTS only (for PLUSNUTS use C-1000 tool)

Wrench Type Header for Thread Sizes 4-40, 6-32, 8-32, 10-32,10-24, 1/4”-20, 1/4”-28. Metric: M3 x 0.5, M4 x 0.7, M5 x 0.8and M6 x 1.0. Specify size.

PNEUMATIC TYPECN9P25-(specify size) Cap: 4-40 thru 10-32CN9P7-(specify size) Cap: 10-24 thru 3/8-16

SIOUX

This driver is a quick way to set threaded inserts (thru type only). Other models and sizes available.Specify size: 4-40 thru 3/8-16.CONVERSION ASS'Y AVAILABLE:Specify Size: 4-40 thru 3/8-16

Semi-production high speed tool. Push-pull knob threads rivet-nut on and off.Adjustable anvil for different grip ranges.

CONVERSION KITS AVAILABLE6-32, 8-32, 10-32#SCA (SPECIFY SIZE)4-40#SCA 4-40. . . . . . . .

#L6000-Price . . . . . . . . . . . . .6-32 Thru 10-32 Model(specify the size)L6OOO-4-40Price . . . . . . . . . . . . . . . . . . . . . .4-40 Model#283-6009Price . . . . . . . . . . .1/4-28 Heavy Duty Model

L3600 – SPECIFY SIZE

• RECOMMENDED FOR SNIPPING KEYWAY NOTCH IN THINMETAL FOR KEYED RIVET NUT FASTENERS

• AVAILABLE IN SIZES: #4 thru 1/4”, SPECIFY• ALSO AVAILABLE IN COUNTERSUNK• RECOMMENDED FOR USE ON: 3/32” ALUMINUM

1/16” MILD STEEL• REPAIR PARTS AVAILABLE• 10 LBS.44

SPIN PULL RIVNUTER Introducing the new Model 150-SP lightweight spin-pull tool...A totally different tool for up-setting Rivet-Nuts and “Thread-Serts”. Self-aligning air supplyautomatically adjusts for pressures. Insert spins on bysimply pushing onto mandrel. Rocket trigger upsetsinsert and spins off. Swivel air inlet for unrestricted,versatile motion. Totally adjustable stroke for all gripranges. Installs more fasteners per minute with lesseffort. Works on 80-95 P.S.I. Weighs only 5-3⁄4 lbs.Handles sizes 4-40, 6-32, 8-32, 10-32, 10-24. 1/4-20, 1/4-28, 5/16-18, 5/16-24, 3/8-16, 3/8-24, 1/2-13, and 1/2-20. Also available in these metric sizes:3.5MM, 4MM, 5MM, 6MM, 8MM, 10MM. Kit includes6-32 thru 3/8-16 mandrels and nosepieces.

#150 SP.....

AIR DRILLSEXPERT REPAIRS

ON ALL BRANDSALL MAJOR BRANDS AVAILABLE

Introducing...The New signature Series Drills

For The Aviation and Aerospace Industry

Precision Toolsfor precise performanceThrough next generation ergonomics and the continued focus on productivity andoperator safety comes the development of the Sioux Tools Signature Series Drill line. Signature Series Drills are used throughout the military, commercial and privateaerospace industry. The powerful five vane motor makes these drills great for drillingapplications that contain ferrous and non-ferrous metals, wood and compositematerials. The Signature Series Drills offer great value with a 3 planet gear system for increased life and load capacity. The Signature Series Drill has impressive runoutof less than .005 inches @2-1/2” from the end of the chuck. The Sioux toolsSignature Series Drill line reduces operator fatigue by offering a low sound level and low vibration solution! Operator comfort is achieved through the implementationof a light weight aluminum housing and a comfort grip. Drills are available in bothreversing and non-reversing pistol grip and lever handle configurations.

Model Number Free Speedrpm

Chuck Capacityin. mm

Weightlb. kg

Lengthin. mm

Side to Centerin. mm

Air Consumptionscfm l/s..

Sound LeveldB(A)

Spindle Thread

Pistol Grip Non-Reversing Drills (0.6 HP)SDR6P60N2 6,000 1/4 6 2.10 0.95 5.8 145 0.8 20 25 11.8 80 3/8"-24SDR6P60N3 6,000 3/8 10 2.25 1.00 6.3 160 0.8 20 25 11.8 80 3/8"-24SDR6P40N2 4,000 1/4 6 2.10 0.95 5.8 145 0.8 20 25 11.8 80 3/8"-24SDR6P40N3 4,000 3/8 10 2.25 1.00 6.3 160 0.8 20 25 11.8 80 3/8"-24SDR6P26N2 2,600 1/4 6 2.10 0.95 5.8 145 0.8 20 25 11.8 80 3/8"-24SDR6P26N3 2,600 3/8 10 2.25 1.00 6.3 160 0.8 20 25 11.8 80 3/8"-24SDR6P26N4 2,600 1/2 13 2.70 1.20 6.6 170 0.8 20 25 11.8 80 1/2"-20SDR6P12N3 1,200 3/8 10 2.70 1.20 7.3 185 0.8 20 25 11.8 80 3/8"-24SDR6P7N3 700 3/8 10 2.70 1.20 7.3 185 0.8 20 25 11.8 80 1/2"-20SDR6P7N4 700 1/2 13 3.10 1.40 7.8 200 0.8 20 25 11.8 80 1/2"-20SDR6P4N3 400 3/8 10 2.70 1.20 7.3 185 0.8 20 25 11.8 80 1/2"-20SDR6P4N4 400 1/2 13 3.10 1.40 7.8 200 0.8 20 25 11.8 80 1/2"-20

Model Number Free Speedrpm

Chuck Capacityin. mm

Weightlb. kg

Lengthin. mm

Side to Centerin. mm

Air Consumptionscfm l/s..

Sound LeveldB(A)

Spindle Thread

Pistol Grip Non-Reversing Drills (1.0 HP)SDR10P60N2 6,000 1/4 6 2.30 1.05 6.5 165 0.8 20 30 14.2 80 3/8"-24SDR10P60N3 6,000 3/8 10 2.45 1.10 7.0 180 0.8 20 30 14.2 80 3/8"-24SDR10P40N2 4,000 1/4 6 2.30 1.05 6.5 165 0.8 20 30 14.2 80 3/8"-24SDR10P40N3 4,000 3/8 10 2.45 1.10 7.0 180 0.8 20 30 14.2 80 3/8"-24SDR10P26N2 2,600 1/4 6 2.30 1.05 6.5 165 0.8 20 30 14.2 80 3/8"-24SDR10P26N3 2,600 3/8 10 2.45 1.10 7.0 180 0.8 20 30 14.2 80 3/8"-24SDR10P26N4 2,600 1/2 13 2.90 1.30 7.5 190 0.8 20 30 14.2 80 1/2"-20SDR10P12N3 1,200 3/8 10 2.90 1.30 8.0 205 0.8 20 30 14.2 80 3/8"-24SDR10P7N3 700 3/8 10 2.90 1.30 8.0 205 0.8 20 30 14.2 80 1/2"-20SDR10P7N4 700 1/2 13 3.30 1.50 8.5 215 0.8 20 30 14.2 80 1/2"-20SDR10P4N3 400 3/8 10 2.90 1.30 8.0 205 0.8 20 30 14.2 80 1/2"-20SDR10P4N4 400 1/2 13 3.30 1.50 8.5 215 0.8 20 30 14.2 80 1/2"-20

Inline Non-Reversing Drills (1.0 HP)SDR10S60N2 6,000 1/4 6 2.20 1.00 7.8 200 0.8 19 30 14.2 78 3/8"-24SDR10S60N3 6,000 3/8 10 2.30 1.05 8.3 210 0.8 19 30 14.2 78 3/8"-24SDR10S40N2 4,000 1/4 6 2.20 1.00 7.8 200 0.8 19 30 14.2 78 3/8"-24SDR10S40N3 4,000 3/8 10 2.30 1.05 8.3 210 0.8 19 30 14.2 78 3/8"-24SDR10S26N2 2,600 1/4 6 2.20 1.00 7.8 200 0.8 19 30 14.2 78 3/8"-24SDR10S26N3 2,600 3/8 10 2.30 1.05 8.3 210 0.8 19 30 14.2 78 3/8"-24SDR10S12N3 1,200 3/8 10 2.75 1.25 9.3 235 0.8 19 30 14.2 78 3/8"-24SDR10S7N3 700 3/8 10 2.75 1.25 9.3 235 0.8 19 30 14.2 78 1/2"-20SDR10S4N3 400 3/8 10 2.75 1.25 9.3 235 0.8 19 30 14.2 78 1/2"-20SDR10S4N4 400 1/2 13 3.20 1.45 9.8 250 0.8 19 30 14.2 78 1/2"-20

ALSO AVAILABLE WITH REVERSE

KT842283/8” CAP

“ECONOMY” MODELREVERSIBLE

2,000 RPM 3 LBS.

KT842291/2” CAP

“ECONOMY” MODEL

500 RPM 4 LBS.

DESOUTTER

12641/4” CAP

RPM WEIGHT(lbs.)

2,900 RPM 2 LBS.

“ECONOMY” MODEL

2,200 RPM 2-3/4 LBS.KT842183/8” CAP

SIOUX “MINI AIR DRILL”

MODEL NO. 1410 1412RPM 2600 3600

Chuck Cap. 1/4” 1/4”Side to Center 37/64” 37/64”

Weight 1 lb. 4 oz. 1 lb. 4 oz.Horse Power .33 .33

Length 6-1/4” 6-1/4”

FP5950 3/8” Cap.JACOBS 1B 1/4” Cap.JACOBS 7BA 3/8” Cap.JACOBS (1/2-20) 33BA 1/2” Cap.JACOBS KEYLESS 65562 3/8” Cap. 45

REPLACEMENT CHUCKS WITH KEYS (3/8-24 Thd.)ECONOMY

DOTCO® DRILLS

Pistol Grip Drills

DOTCO®

330 – 29,000 RPM0.4 – 0.9 hp (0.30 – 0.67 kW)

■ Non-reversible

■ Ergonomically critical finger andthumb guides fit the hand to aidin control

■ Excellent for aerospace, metalfab and woodworking

Model Number Weight** Length**FreeSpeed

rpmWith Chuck Without Chuck lbs. kgs. in.. mm

14CF Series – 0.4 hp (0.30 kW) – Non-reversible14CFS90-38 29,000 1/4” 1.5 0.68 5.7 145 3/8” 1/4”14CFS91-38 5,200 1/4” 1.5 0.68 5.7 145 3/8” 1/4”14CFS92-38 3,800 1/4” 1.5 0.68 5.7 145 3/8” 1/4”14CFS93-38 3,200 1/4” 1.5 0.68 5.7 145 3/8” 1/4”14CFS94-38 2,400 1/4” 1.6 0.72 5.7 145 3/8” 1/4”14CFS95-38 1,000 1/4” 1.8 0.82 6.9 175 3/8” 1/4”14CFS96-38 700 1/4” 1.8 0.82 6.9 175 3/8” 1/4”14CFS97-38 600 1/4” 1.8 0.82 6.9 175 3/8” 1/4”

14CS Series – 0.6 hp (0.45 kW) – Non-reversible14CSL90-38 14CSL90-40 20,000 1/4” 2.1 0.95 6.3 160 1/4” 1/4”14CSL98-38 14CSL98-40 6,000 1/4” 2.1 0.95 6.3 160 1/4” 1/4”14CSL91-38 14CSL91-40 5,200 1/4” 2.1 0.95 6.3 160 1/4” 1/4”14CSL92-38 14CSL92-40 3,200 1/4” 2.1 0.95 6.3 160 1/4” 1/4”14CSL95-51 14CSL95-40 1,300 3/8” 2.9 1.31 8.1 205 3/8” 1/4”14CSL97-51 14CSL97-40 500 3/8” 2.9 1.31 8.1 205 3/8” 1/4”

14CN Series – 0.9 hp (0.67 kW) – Non-reversible14CNL90-38 14CNL90-40 20,000 1/4” 2.2 1.00 6.8 173 1/4” 1/4”14CNL98-38 14CNL98-40 6,000 1/4” 2.2 1.00 6.8 173 1/4” 1/4”14CNL91-51 14CNL91-40 5,200 3/8” 2.4 1.08 7.2 183 3/8” 1/4”14CNL92-51 14CNL92-40 3,200 3/8” 2.4 1.08 7.2 183 3/8” 1/4”14CNL95-51 14CNL95-40 1,300 3/8” 2.8 1.27 8.6 218 3/8” 1/4”14CNL97-53 14CNL97-40 500 1/2” 3.5 1.59 9.1 231 1/2” 1/4”

DrillDiameterCapacity

GearedChuck Size

AirInlet Size

14CF

14CS

14CN

GENERAL: 14CS, 14CN: Jacobs geared chuck, chuck key,See page ? for additional features and benefits. dead handle (All models with a chuck opening greater than 1/2”)Air Inlet, 1/4” NPT – Use 5/16” (7.9mm) I.D. hose. EXTRA EQUIPMENT:Tools performance rated at 90psi (620 kPa) air pressure. Overhose: STANDARD EQUIPMENT: 14CF: Jacobs geared chuck, chuck key

WARNING: Face & eye protection must be worn while operating power tools, per ANSI B186.1. Cutting tool maximum speed rating must equal or exceed speed of air tool @90psi(620 kPa). Follow cutting tool manufacturer’s mounting & operating instructions. Tools must be equipped with lock-off lever to be CE compliant.46

!

MASTER POWER MINI AIR DRILLS

CLECO AIR DRILLS

47

Pistol Grip DrillsNon-Reversible

Nominal Motor Power 0.4 hp0.3 kW

Non-Reversible

360° Rotatable exhaust

Low Noise

Two Stage Throttle

Bearing supported output spindle assuresminimum run-out

Model NumberMax

Free RPM

Chuck

CapacitySpindle Offset

In. mm

Weight

lbs. Kg

Length

In. mmHp.

MP1451-38•• 5200 .4 1/4” .69 17 6.3 159 1.5 .68

MP1453-38•• 3200 .4 1/4” .69 17 6.3 159 1.5 .68

GeneralAir Inlet: 1/4” NPT – Use 1/4” (6.4mm) I.D. hoseAll tools performance rated @ 90 psi (620 kPa) air pressure

STANDARD EQUIPMENTGeared chuck, chuck key

NO. 135 VARIABLE SPEED DRILLS

FEATURES:• Calibrated dial on rear of tool simplifies drill speed

selection

• Choice of three governed speed models to matchmaterial being drilled

• Powerful air motor produces .7 nominal horsepower

• Can be used with Feed Assist for more accurate,perpendicular holes135 DPV–14B-51

SPECIFICATIONS

ModelNumber

135 DPV-7B-43135 DPV-14B-51135 DPV-28B-51

60012502600

150-550400-1200100-2400

3/85/165/16

1088

9 5/89 1/48 1/2

244235216

3-5/83-3/83-1/8

1.61.51.4

SPEEDS rpm

FREE GOVERNED in. mm in. mm lb. Kg.

CHUCK CAPACITY (SEE CAPACITY NOTE)

LENGTH WEIGHT

Performance rated @ 90 PSIG (6.2 BAR)Air Inlet: 1/4” N.P.T.F.Minimum Hose Size: 5/16” (6mm)Spindle Offset: 25/32” (20mm)

STANDARD EQUIPMENT3-JAW CHUCK AND KEY.OPERATING INSTRUCTIONS AND SERVICE MANUAL

CAPACITY CAUTION NOTE: 135DPV DRILLS MUST BE EQUIPPED WITHDEAD HANDLE (861006) IF 1/2 IN. (13MM) CAPACITY CHUCK IS SPECIFIED.

Speed Range: 150 T0 2400 rpm

Nominal Motor Power .7 HP

*

* Available with 3/8” or 1/2” chuck.

PORTABLE DRILL BUSHING ASSEMBLY

1-1/2 DIA.

HOUSINGSLIP

BUSHINGS

1/2–13 THD.

1-3/4 DIA.589DA = .312 I.D. LINERDRILL RANGE #80-#10589EA = .500 I.D. LINERDRILL RANGE #28-11/32

*AVAILABLE EITHER ‘DA’ OR ‘EA’ STYLE BUSHING

.4998 DIADA-BUSHING 1/2” LONG

EA-BUSHING 3/4” LONG

USE STANDARD SLIPRENEWABLE DRILL

48

49

6-1/2”

7-1/8”

7-1/8”

6”

6”

7-1/2”

1-3/16”

1-3/8”

2-7/16”

.384”

.425”

.212”

.290”

1”

3/4”

1-1/16”

1”

.290

50

TERRY # T-21 AND # T-23 THIN HEAD OFFSET DRILLING ATTACHMENT

Designed for drilling in narrow channels, Terry #T-21 and the heavier #T-23are ideal for many difficult drilling jobs.

DIMENSIONS

# T-21 #T-231/4” A 7/16”7/8” B 1”1-1/2” C 2-3/16”3/4” D 1-5/32”1/2” E 3/4”5-5/8” F 6-1/2”1/4” G 1/4”10-32 H 10-32or or1/4-28 1/4-28

Capacity#T-21 1/8”#T-23 1/4”

Same as T 25 above, but with longhandle.

Capacity – 1/4” maximumDIMENSIONSA – 2-5/16”B – 3-3/16”C – 7/16”D – 11/16”E – 1/4”F – 7/8”G – 1/4” - 28 thread

THE ORIGINAL

DRILLING ATTACHMENT

TERRY NO. N 6 – Straight Flexible (Snake) DrillingAttachment with 1/4” – 28 threaded spindle

TERRY NO. N 51-1 – Right Angle Flexible DrillingAttachment. (1/4”-28 THD)

TERRY NO. N 63 – Right Angle Flexible DrillingAttachment. A combination of the No. 3 Right AngleHead Assembly from the Terry No. 3 (1/4”-28 THD)

TERRY NO. T 235 – Flat Offset Drilling Attachment (ShortHandle) with 1/4”-28 threaded spindle. The 2-5/16” offsetgives greater access to tight places. Needle Bearings inthe Handle, Hardened Alloy Steel Drive Shaft and Gearsmake this a most durable tool.

TERRY NO. T-25 – Flat Offset Drilling Attachment (LongHandle) with 1/4”-28 threaded spindle.

30”

15/16

22”

30”

6-5/8”

®

51

1AM1541-450

1AM1551-900

R.P.M. Side To Spindle Min. Overall Net. Wt.No. Cat. Center Thread Hose Hose Length Tool Only

Load H.P. No. Inches (Female) Conn. Size Ins. Lbs. Oz.2800 .33 1AM1541-45o 21/64 1/4”-28 1/4” 1/4” 10.2 1.85800 .75 2A1410-45o 21/64 1/4”-28 1/4” 3/8” 11-15/16 2.72800 .33 1AM1551-90o 21/64 1/4”-28 1/4” 1/4” 9.7 1.55800 .75 2A1410-AH 21/64 1/4”-28 1/4” 3/8” 11-7/16 2.72800 .33 60-032 7/16 1/4”-28 1/8” 1/4” 10-5/8 1.103350 .75 2L1380 - - ConeJaw 1/4” 3/8” 13-3/4 2.32200 .50 2S1310 29/32 1/4 Chuck 1/4” 1/4” 3-9/16 2.103500 .50 2S1410 29/32 1/4 Chuck 1/4” 1/4” 3-9/16 2.10

Aircraft SpecialtyTools-Angle Drills

Non-

Reve

rsib

le

2L1380

No. 2S1310

No. 60-032Flathead Drill (NOT A Sioux Tool)

DOTCO® ERGONOMIC RIGHT ANGLE DRILLS

†– Collet ModelSEE PAGE 53 FOR COLLETS

Model #: 15LF281-62

4 1/8”

4 1/8”

4 1/2”

3 7/16”

1 1/8”

5/8”

4 1/8”

5/8”5/8”

5/8”

5/8”

15/16”

-62 1/4”-28 Internal Thread

52

ANGLE DRILLS AND ACCESSORIES

LONG REACH RIGHT ANGLE DRILL

CONE-JAW CHUCK

1/4-28 THD.

#M3. . . . . . . . . . . . . . . . . . . . . . . .

BROKEN DRILL COLLETS(CAN'T SLIP – NO BRAZING)

This type of collet is slotted withinternal prongs that grip on fluteof drill.

SERIES 29621/4-28 THD. SHK.

1-1/4" O.A.L.

HIGH SPEED STEELTHREADED SHANKADAPTER DRILLS

SIZE 1/4 10 11 12 16 19 20 21 27 29 30 40

SERIES 29721/4-28 THD. SHK.

2-1/4" O.A.L.

COLLETS200-SPECIFY#40,30,21,10

300-1/4. . . . .

ADAPTER200-1/4"-28

300-1/4-28. . . . .

DRILL COLLETS

1/4-28 THREADED SHANK

COLLETS FOR ATLAS, COPCO,LBV 25 (–91) and LBV 36 (-91)

& DESOUTTER: D314, D315, D374

mm in. part no. mm in. part no.1.6 18922 4.0 (5/32) 190521.8 18932 4.2 190622.0 18942 4.4 190722.2 18952 4.6 190822.4 (3/32) 18962 4.8 (3/16) 190922.6 18972 5.0 191022.8 18982 5.2 191223.0 18992 5.4 191323.2 (1/8) 19002 5.6 191423.4 19022 5.8 191523.6 19032 6.0 191623.8 19042 6.2 19172

6.4 (1/4) 19182

127590. . . . . . . . . .

Accepts 1/4"-28Threaded Drill Bits2800 RPM

FP 787A 3/8 CAP.

STUB ANDLONGLENGTHSAVAILABLE

COBALTAVAILABLE

Reversible ..........1800 RPM 2 lbs.

537 3/8”

(187 .3mm)

31/32”(24.61mm)

5/16”(7.94mm)

13 1/2”(323.8mm)

1 5/16”(33.4mm)

DESOUTTER® ANGLE DRILLS

54

*COLLET SPINDLE – 5mm (3/16”) CAPACITYLever Start

D32-L-5200C 205 146 651 4 5200 0.28 0.38 0.72 1.6 9.4 19.9D32-L-2800C 1460764 2800 0.28 0.38 0.72 1.6 9.4 19.9D32-LX-1800C 1458224 1800 0.12 0.16 0.72 1.6 5.0 10.6

Button Start

Lever Start

D32-S-5200 1465344 5200 0.28 0.38 0.72 1.6 9.4 19.9D32-S-4000 1465354 4000 0.28 0.38 0.72 1.6 9.4 19.9D32-S-2800 1465364 2800 0.28 0.38 0.72 1.6 9.4 19.9

D32-L-2800S 1460754 2800 0.28 0.38 0.72 1.6 9.4 19.9D32-LX-1800S 1458204 1800 0.12 0.16 0.72 1.6 5.0 10.6

1/4” X 28 SPINDLE – 5mm (3/16”) CAPACITY

*COLLET SPINDLE – 6.4mm (1/4”) CAPACITY *See Page 53 for Collets

1/4” x 28 Spindle – 6.4mm (1/4”) CAPACITY

Lever Start

D315-S-2800 1381464 2800 0.28 0.38 0.79 1.7 269 10.59 9.4 19.9D315-S-1750 1382014 1750 0.28 0.38 0.79 1.7 291 11.46 9.4 19.9

D315-S-1050 1382434 1050 0.28 0.38 0.90 2.0 291 11.46 9.4 19.9

D315-L-4400 1462134 4400 0.28 0.38 0.79 1.7 269 10.59 9.4 19.9D315-L-2800 1381544 2800 0.28 0.38 0.79 1.7 269 10.59 9.4 19.9D315-L-1750 1382194 1750 0.28 0.38 0.90 2.0 291 11.46 9.4 19.9

Lever StartD315-L-4400S 1456934 4400 0.28 0.38 0.79 1.7 269 10.59 9.4 19.9D315-L-2800S 1456944 2800 0.28 0.38 0.79 1.7 269 10.59 9.4 19.9D315-L-1750S 1456954 1750 0.28 0.38 0.90 2.0 291 11.46 9.4 19.9D315-L-1050S 1456964 1050 0.28 0.38 0.90 2.0 291 11.46 9.4 19.9D315-L-400S 1456974 400 0.28 0.38 0.90 2.0 291 11.46 9.4 19.9

Button Start

CD32-L-Interchangeable Level Included

D32-S-B

Compact 90º Angle Head0.12 to 0.38 kW (0.16 to 0.50 hp) -580 to 5200 rpm

PICREF

MODEL PART NUMBER

FREE SPEED

rpm

MOTORPOWER

KW HP

Weight

kg lb

AIR FLOW

kg cfm

Standard 45 Angle Head0.28 kW (0.38 hp) – 400 to 4400 rpm

D315-L

DESOUTTER® ANGLE DRILLS

55

Compact 30º and 90º x Angle Head (360º)0.12 - 0.28 kW (0.16-0.38hp) – 2000 to 5700 rpm

PICREF

MODEL PART NUMBER

FREE SPEED

rpm

MOTORPOWER

KW HP

Weight

kg lb

AIR FLOW

kg cfm

Interchangeable lever included D

AD33–S–

D370–L–

*COLLET SPINDLE – 5mm (3/16”) CAPACITY - 30º

*COLLET SPINDLE – 5mm (3/16”) CAPACITY - 360º

Button Start

Lever Start

Lever Start

Lever Start

Lever Start

1/4” X 28 SPINDLE – 5mm (3/16”) CAPACITY - 360º

A D33-SX-2000 1379204 2000 0.12 0.16 0.62 1.4 5.0 10.6A D33-S-5700 1465374 5700 0.28 0.38 0.62 1.4 9.4 19.9

Button StartC D370-SX-2000 1379464 2000 0.12 0.16 0.72 1.6 5.0 10.6

D D370-LX-2000 1379544 2000 0.12 0.16 0.72 1.6 5.0 10.6D D370-L-3000 1464794 3000 0.28 0.38 0.72 1.6 9.4 19.9

D D370-LX-2000S 1464804 2000 0.12 0.16 0.72 1.6 5.0 10.6D D370-L-3000S 1464814 3000 0.28 0.38 0.72 1.6 9.4 19.9

A D33-S-4400 1465384 4400 0.28 0.38 0.62 1.4 9.4 19.9A D33-S-2800 1465394 2800 0.28 0.38 0.62 1.4 9.4 19.9

B D33-LX-2000 1379384 2000 0.12 0.16 0.62 1.4 5.0 19.9B D33-L-3000 1464764 3000 0.28 0.38 0.62 1.4 9.4 19.9

B D33-LX-2000S 1464834 2000 0.12 0.16 0.62 1.4 5.0 10.6B D33-L-3000S 1464824 3000 0.28 0.38 0.62 1.4 9.4 19.9

1/4” X 28 SPINDLE – 5mm (3/16”) CAPACITY - 30º

*See Page 53 for Collets

AIRCRAFT DRILL BITS (HIGH SPEED STEEL) PER NAS907 SPECIFICATIONS

56

JOBBERS LENGTH118° S/P

R18A

#5#10#16#20#21#27#30#40

R10A

1/163/321/85/323/161/45/163/8

6” AIRCRAFT EXTENSION135° S/P

501-6

#5#10#16#20#21#27#30#40

500-6

1/163/321/85/323/161/45/163/8

SCREW MACHINE (“SHORTIE”)135° S/P

R41C

#5#10#16#20#21#27#30#40

R40C

1/163/321/85/323/161/45/163/8

12” AIRCRAFT EXTENSION

135° S/P501-12

#5#10#16#20#21#27#30#40

500-12

1/163/321/85/323/161/45/163/8

STANDARD PACK = 12 PIECESWE OFFER PILOTED DRILLS AND REAMERS TO SPECIFICATION

UNI1 #10231 Step Drill, 13 Hole Sizes: 1/8” to 1/2”UNI2 #10232 Step Drill, 6 Hole Sizes: 3/16” to 1/2”UNI3 #10233 Step Drill, 9 Hole Sizes: 1/4” to 3/4”UNI4 #10234 Step Drill, 12 Hole Sizes: 3/16” to 7/8”UNI20 #10220 Step Drill, 8 Hole Sizes: 9/16” to 1”UNI21 #10221 Step Drill, 10 Hole Sizes:

13/16” to 1-3/8”UNI502 #10502 Step Drill, 3 pcs., Hole Sizes: #1, #2, and #3

DRILL SETSJOBBERS LENGTH DRILL SETHigh Speed Steel, Surface Treated*R10 Fractional Sizes

JOBBERS LENGTHDRILL SETHigh Speed Steel, Surface Treated*R18 Wire Sizes

JOBBERS LENGTHDRILL SETHigh Speed Steel, Surface Treated*R15 Letter Sizes

C162-HB29Pc. Set in Metal Index1/16-1/2” by 64ths

C163-HB15Pc. Set in Metal Index1/16-1/2” by 32ths

C61-HB20 Pc. Set in Metal Index61-80

C1-HB60 Pc. Set in Metal Index1-60

CAZ-HB26Pc. Set in Metal IndexA-Z

AIRCRAFT DRILL BITS (COBALT) PER NAS907 SPECIFICATIONS TYPE “J”

06721 3/32 1/2 .004 1/806741 1/8 1/2 .004 1/806761 5/32 1/2 .004 1/806781 3/16 1/2 .004 1/806801 1/4 1/2 .004 1/8

STAINLESS

PILOT BRUSHESPILOTDIA.

BRUSHDIA.

TRIM LENGTHFROM RING

WIRESIZE

Stem Diameter-1/4” Max. Safe Speed 8,000 R.P.M

BODYDIAMETER5/8”

DRILLSTOPS

Standard Pak = 12 pieces

57

TAP SETS

58

TAPPERS

Tape

r Cha

mfe

r

Plu

g C

ham

fer

Bot

tom

ing

Cha

mfe

r Each Set Contains Three Taps:

EXPLANATION OF DESCRIPTION

ORDER BY SET NUMBERS OR INDIVIDUAL TAP NUMBER

PITCH DIA.LIMIT NO.

H2H3

FL Str. Flute

TYPE FLUTESSymbol Explanation THREAD

Number of threadsper inch

SIZE

Numbered Sizesand Fractional

Sizes as Shown

THE HANSON-WHITNEYCOMPANY

High Speed Steel… Ground Thread MADE IN USA

* RAPID REVERSE* CAPACITY OF 1/4” IN STEEL, 5/16” IN ALUMINUM* TP9A-4C20 CAPACITY No. 10-5/16” THREAD SIZE* TP9A-4C32 CAPACITY 1/4” – 1/2” THREAD SIZE

TP9-A-4C20

Handle

Pistol Rev. 400 TP9A-4C20 29/32 310 1/4” PT 1/4” 8-1/4 2.15

400 TP9A-4C32 29/32 310 1/4” PT 1/4” 8-1/2 3.00

R.P.M.No

LoadCatalog Number

Torque In Lbs.

HoseConn.

Sides ToCenterInches

Min. Hose Size

Net WeightTool OnlyLbs. Ozs.

OverallLengthInches

NO.FLUTES

34

SCREW EXTRACTORS

High Speed Steel, Screw ExtractorSCREW EXTRACTORS

“Easy Outs”SPIRAL FLUTE

SCREW EXTRACTOR SET20 PK.

5 Pc. Set in Plastic Pouch#1, 2, 3, 4, 5

SCREW EXTRACTOR SET45 PK.

6 Pc. Set in Plastic Pouch#1, 2, 3, 4, 5, 6

H.S.S. CHUCKING REAMERS

AIRCRAFT TAPER ROUTER

SERIES 740 – Right Hand Spiral Flute

SERIES 720 – Left Hand Spiral Flute

SERIES 700 – Straight Flute

SERIES 700C – Straight Flute Cobalt

Special Piloted (STEP)

Reamers Available Per Your Spec.

HSS OR CARBIDE

High Speed Steel R.H. Helix, R.H. Cut. Taper 1/4” Per FootTaper routers are used for cutting, trimming and routingaround cowling, door sills and plexi-glass, trimming onwing terminals on bulkheads and ribs on fuselage.

The advantages over taper pin reamers and drills are the ability to cut without drilling first, easier guiding along the pattern and freer cutting without buildup.

No.

12345

678910

1112

3/16– 1/41/4– 5/165/16–7/167/16 –9/169/16 – 3/4

3/4 –11–1-3/8

1-3/8–1-3/41-3/4–2-1/82-1/8–2-1/2

2-1/2–33–3-1/2

SmallEnd

LargeEnd

FluteLgth

DrillSize

Part NumberO.A.L

1/27/811-1/41-1/2

1-3/42-1/42-1/42-1/42-1/2

33-1/2

5/647/645/321/417/64

13/3217/3213/161-1/161-5/16

1-9/161-15/16

22-3/82-11/1633-3/8

3-3/44-1/84-3/84-5/85

5-5/86-1/4

1/813/641/411/327/16

19/3225/321-1/321-9/321-9/16

1-7/82-5/16

EZ1EZ2EZ3EZ4EZ5

EZ6EZ7EZ8EZ9EZ10

EZ11EZ12

Nominal DiameterAt

Part No.

ATR1ATR2ATR3ATR4

ShankDiam.Inches

.0980

.1280

.1875

.2500

SmallEnd

Inches

.0810

.1100

.1650

.2240

LargeEnd

Inches

.0980

.1280

.1875

.2500

FluteLengthInches

13/167/8

1-1/161-1/4

OverallLengthInches

22-1/42-1/22-3/4

SizeNo.1234

BoltSize

1/163/321/83/161/4

3/81/23/411-1/4

1-1/21-27/32

59

SHEET METAL CLAMPS “CLECOS”

PNEUMATIC SKIN CLAMP TOOL

KWIK-LOK- TEMPORARY REUSABLE CLAMPSA diversity or plier actuated clamps for precise holding of materials.

The K-type sheet holder clamp is the standard clamp. It is plier-actuated, spring-loaded and steel bodied

The KK-type sheet holder clamp isdesigned for those space requirementswhich prohibit the use of standard K-type clamp. The KK-type is a miniatureclamp, with a shorter overall body andspecial effectiveness for more confinedareas.

The KL and KEL-type clamps are standard K-typeclamps with an extended grip range.

KL / KEL

PART NO. COLOR CODE G(grip) D(diameter) drill size

KK-3/32 zinc 3/32” #40KK-1/8 copper 1/8” #30KK-5/32 black 5/32 #20KK-3/16 brass 3/16” #10

0-1/4”

KL-3/32 zinc 3/32” #40KL-1/8 copper 1/8” #30KL-5/32 black 5/32 #20KL-3/16 brass 3/16” #10

KEL-3/32 zinc 3/32” #40KEL-1/8 copper 1/8” #30KEL-5/32 black 5/32 #20KEL-3/16 brass 3/16” #10

1/4” – 1/2”

1/2” – 3/4”

* Trigger Throttle* Ergonomic Handle* 1/4” NPT Air Inlet* Quiet Operation* 360º Swivel Mount* For use on button type

and side grip temporaryfasteners

* Made in USA

The Pneumatic Cleco Fastener Installation Tool hasbeen developed to eliminate the constant, repetitivemotion associated with the common Cleco Plier. It also adds speed and efficiency to the installation of Cleco Fasteners.

PNEUMATIC CLECO INSTALLER

No. PA20112…

KSG 1/2”X1/2” 0-1/2” copperKSG 3/4”X1/2” 0-3/4” brassKSG 1/2”X1” 0-1/2” copperKSG 3/4”X1” 0-3/4” brass

Part No. Grip Color Code

KSG-SIDE GRIPS – edge clamps to holdmaterials together where no holes areprovided. Plier operated. Suggested forbonding, gluing and sealants.

NEW CLECO PLIERSWith Protective Hand Grip

Model #K200P

KK

60

POWER-OPERATED TEMPORARY FASTENERS

POWER FASTENER GUNS

NO-MARK FASTENERS

No. SR9A-25Skin ClampRunner

No. 2S2300SRSkin ClampRunner

Description Handle

R.P.M.No

Load

Min Hose Size

OverallLength

Ins.

Side ToCenterInches

Cat No.

HoseConn.

Skin Clamp Runner Pistol Rev 2,500 SR9A-25 29/32 1/4” 1/4” 9-1/8 2-9Skin Clamp Runner “S” Handle Rev 2,500 2S2300SR 29/32 1/4” 1/4” 5-11/16 2-10

* Rapid reverse on SR9A-25Skin Clamp Runner

Plastic Base Cap No Pliers Required Suitable For Composite Structures

Wing Nut FreeWheeling Hand

Fastener

To be used on heavier materials for extra pressure.Available in various sizes and different grip ranges.

61

SIZEPART NO

KWN-FWKWNL-FW

KWNEL-FW

GRIP

0” to 1/2”0” to 1”

1/2” to1-1/2”

3/32 1/18 5/32 3/16 1/4 7/32, 5/16

NOTE: QUANTITY DISCOUNT ABOVE 100 PIECES

Net Wt. Tool Only Lbs. Oz.

Plastic Base Cap

Special Design for Composites

SSL SERIES (Standard Length) SEL SERIES (Extra Long)

TOGGLE CLAMPS

“C” CLAMPS/BODY CLAMPS MECHANICS VISES

ModelNumber With Without

SwivelSpindle

SpindleThread

SizeLength (A)

Reach(B)Gap

HoldingPressure

FC 50

FC 51

FC 53FC 54

•• •

•

•

• 1/4-20

5/16-18

3/8-163/8-16

4-1/2”

6”

8-1/2”8-1/2”

1-1/8

1-3/4

2-3/42-3/4

1

1-1/4

1-3/43

200

350700700

HANDY CLAMPS SPRING CLAMPS SPRING TENSION CLAMPS

62

CLECO® 14 SERIES INLINE SCREWDRIVERSPlus, all new inline models have all the performance-proven features and benefits of our original Cleco 14 Inline Series.

Proven Clecomatic® clutch for greater repeatability Soft oval-shaped housing for a more comfortable gripHigh power-to-weight ratios for reduced cycle timesRear overhose option for lower noise levelsComposite housing for better feel and less vibrationInterchangeable clutch assembly and planetary gears for greater adaptabilityHidden, but easy-to-use access, torque adjustment for reduced online tamperingMultiple handle configurations for maximum operator comfortWide variety of accessories for application flexibility

Push button and sliding knob reverse

Push-to-start and Push & Lever Start

External torque adjustment

Bit & finder and quick change chuck

Sliding knob reverse

External torque adjustment

Quick change drive

THE NEWEST CLECO 14 SERIES INLINE SCREWDRIVERS NOWWITH PUSH-BUTTON REVERSE.Fingertip touch activates / controls reverseaction, resulting in higher productivity levels.Push-button reverse positioned for more “natural” handling

*

*

Model Number

1/4” QC

Torque Range Length

in. mm

Weight

lbs. kgin-lbs Nm

Screw SizeGr. 5 Gr.9.8

in. mm

FreeSpeed

RPM

Screw Size:M2.5 – M4#4 – #10

Torque Range:.06 – 5.1 Nm0.5 – 45 In. Lbs

Screw Size:M3.5 – M6

Torque Range:.02 – 5.1 Nm2.0 – 130 In. Lbs

2, 14 Series

14 Series

Torque Range Length

in. mm

Weight

lbs. kgin-lbs Nm

Screw SizeGr. 5 Gr.9.8in. mm

FreeSpeed

RPM

Model Number

1/4” Quick Change Bit & Finder*

PISTOL GRIP SCREWDRIVERS

Torque Range Length

in. mm

Weight

lbs. kgin-lbs Nm

Screw SizeGr. 5 Gr.9.8in. mm

FreeSpeed

RPM

Model Number

1/4” Quick Change Bit & Finder*

14SPA02Q 14SPA02B #6 M3.5 2800 4 - 19 .5 - 2.1 9.05 230 1.4 0.6314SPA03Q 14SPA03B #8 M3.5 1900 4 - 26 .5 - 2.9 9.25 235 1.4 0.6414SPA04Q 14SPA04B #10 M4 1100 3 - 40 .4 - 4.5 9.05 230 1.3 0.6114SPA05Q 14SPA05B #10 M4 660 2 - 45 2 - 5.1 9.45 240 1.5 0.6714SPA06Q 14SPA06B #10 M4 260 2 - 45 2 - 5.1 9.45 240 1.5 0.68

Push-to-Start - Reversible – Clecomatic Clutch

2RSA-10B #4 M2.5 1000 8 - .5 .9 - .06 7.60 194 0.5 0.202RSA-10SB** #4 M2.5 1000 8 - .5 .9 - .06 6.40 162 0.5 0.20

Push-to-Start - Push Button Reverse – Clecomatic Clutch

14SCA02Q 14SCA02B #6 M3.5 2800 4 - 19 .5 - 2.1 9.80 249 1.5 0.6914SCA03Q 14SCA03B #8 M3.5 1900 4 - 26 .5 - 2.9 10.00 254 1.5 0.7014SCA04Q 14SCA04B #10 M4 1100 3 - 40 .4 - 4.5 9.80 249 1.5 0.6614SCA05Q 14SCA05B #10 M4 660 2 - 45 2 - 5.1 10.20 259 1.6 0.7314SCA06Q 14SCA06B #10 M4 260 2 - 45 2 - 5.1 10.20 259 1.6 0.74

Lever Push-to-Start - Reversible – Clecomatic Clutch

Trigger Start – P Handle – Clecomatic Clutch14PTA02Q #6 M3.5 2800 4 - 19 0.5 - 2.1 8.1 205 1.7 0.814PTA03Q #8 M3.5 1900 4 - 26 0.5 - 2.9 8.3 210 1.8 0.814PTA04Q #10 M4 1100 3 - 40 0.3 - 4.5 8.1 205 1.7 0.814PTA05Q #10 M4 660 2 - 45 0.2 - 5.1 8.5 215 1.8 0.814PTA06Q #10 M4 260 2 - 45 0.2 - 5.1 8.5 215 1.8 0.814PTA07Q #10 M5 660 21 - 60 2.4 - 6.8 9.8 249 2.2 1.014PTA10Q 1/4" M5 400 30 - 87 3.4 - 9.8 10.0 254 2.2 1.014PTA15Q 1/4" M6 250 35 - 130 4.0 - 14.7 9.8 249 2.2 1.0

Push & Trigger Start – P Handle – Clecomatic Clutch14PCA02Q #6 M3.5 2800 4 - 19 0.5 - 2.1 8.2 208 1.7 0.814PCA03Q #8 M3.5 1900 4 - 26 0.5 - 2.9 8.4 213 1.8 0.814PCA04Q #10 M4 1100 3 - 40 0.3 - 4.5 8.2 208 1.7 0.814PCA05Q #10 M4 660 2 - 45 0.2 - 5.1 8.6 218 1.8 0.814PCA06Q #10 M4 260 2 - 45 0.2 - 5.1 8.6 218 1.8 0.8

14BPA02Q #6 M3.5 2300 4 - 14 .5 - 1.6 9.05 230 1.4 0.6314BPA03Q #8 M3.5 1600 4 - 19 .5 - 2.1 9.25 235 1.4 0.6414BPA04Q #10 M4 920 3 - 33 .3 - 3.7 9.05 230 1.3 0.6114BPA05Q #10 M4 560 2 - 45 .2 - 5.1 9.45 240 1.5 0.6714BPA06Q #10 M4 220 2 - 45 .2 - 5.1 9.45 240 1.5 0.68

63

CLECO - NO.8, 88 SERIES SCREWDRIVERS

64

WeightLength*Torque RangeGr. 5 Gr. 9.8

in. mm RPM in. mm lbs. kgin.-lbs. Nm

Screw SizeModel Number

Bit & Finder 3/8” Square Drive1/4 ” Hex

Quick Change

FreeSpeed

Push-to-Start - Sliding Knob ReversePush-to-Start - Sliding Knob Reverse

Push and Trigger Start - Sliding Knob Reverse

Trigger Start - Sliding Knob Reverse

8RSAP-20BQ #10 M4 1800 7-40 .8-4.5 8.5 216 2.8 1.38RSAP-10BQ #10 M5 800 7-65 .8-7.3 9.3 235 3.0 1.48RSAP-7BQ 1/4 M5 550 7-75 .8-8.5 9.3 235 3.0 1.4

WeightLength*Torque RangeGr. 5 Gr. 9.8

in. mm RPM in. mm lbs. kgin.-lbs. Nm

Screw SizeModel Number

Bit & Finder 3/8” Square Drive1/4 ” Hex

Quick Change

FreeSpeed

Push-to-Start - Push Button Reverse

Push-to-Start - Non-Reversible

Push and Lever Start - Push Button Reverse

8RSA-40 8RSA-40BQ #8 M3.5 3200 7-25 .8-2.8 8.9 241 2.1 1.08RSA-30 8RSA-30BQ #10 M4 2500 7-30 .8-3.4 8.9 241 2.1 1.08RSA-20 8RSA-20BQ #10 M4 1800 7-40 .8-4.5 8.9 241 2.1 1.08RSA-10 8RSA-10BQ #10 M5 800 7-65 .8-7.3 9.6 260 2.4 1.1

8RSA-7BQ 1/4 M5 550 7-75 .8-8.5 9.6 260 2.4 1.18RSA-5BQ 1/4 M5 400 7-75 .8-8.5 9.6 260 2.4 1.188RSA-7CQ 88RSA-7C-3 1/4 M6 550 15-95 2-10 9.5 241 2.6 1.288RSA-5CQ 88RSA-5C-3 5/16 M6 400 15-160 2-18 9.5 241 2.6 1.2

8SA-20BQ #10 M4 2000 7-42 .8-4.7 8.5 232 2.0 0.98SA-10 8SA-10BQ #10 M5 1000 7-67 .8-7.6 9.1 251 2.3 1.0

8SA-7BQ 1/4 M5 650 7-75 .8-8.5 9.1 251 2.3 1.088SA-7CQ 1/4 M6 650 15-100 2-11 9.1 232 2.5 1.188SA-5CQ 88SA-5C-3 5/16 M6 500 15-170 2-19 9.1 232 2.5 1.1

8RSAL-20 8RSAL-20BQ #10 M4 1800 7-38 .8-4.3 10.5 282 2.6 1.28RSAL-10BQ #10 M5 800 7-60 .8-6.8 11.3 302 2.9 1.388RSAL-5CQ 88RSAL-5C-3 5/16 M6 400 15-160 2-18 11.1 282 3.1 1.4

8RSATP-30BQ 10 M4 2500 7-30 .8-3.4 8.4 213 2.8 1.38RSATP-20BQ 10 M4 1800 7-40 .8-4.5 8.4 213 2.8 1.38RSATP-10BQ 10 M5 800 7-65 .8-7.3 9.1 232 3.0 1.48RSATP-7BQ 1/4 M5 550 7-75 .8-8.5 9.1 232 3.0 1.48RSATP-5BQ 1/4 M5 400 7-75 .8-8.5 9.1 232 3.0 1.488RSATP-7CQ 88RSATP-7C-3 1/4 M6 550 15-95 2-10 8.9 225 3.1 1.488RSATP-5CQ 88RSATP-5C-3 5/16 M6 400 15-160 2-18 8.9 225 3.1 1.488RSATP-2CQ 88RSATP-2C-3 5/16 M6 200 15-180 2-20 9.6 245 3.4 1.5

8RSAPT-40BQ #8 M3.5 3200 7-25 .8-2.8 8.5 216 2.8 1.38RSAPT-20BQ #10 M4 1800 7-40 .8-4.5 8.5 216 2.8 1.3

8RSAPT-10BQ 8RSAPT-10BQ #10 M5 800 7-65 .8-7 .3 9.3 235 3.0 1.48RSAPT-7BQ 1/4 M5 550 7-75 .8-8.5 9.3 235 3.0 1.4

8RSAPT-5B 8RSAPT-5BQ 1/4 M5 400 7-75 .8-8.5 9.3 235 3.0 1.488RSAPT-7CQ 1/4 M6 550 15-95 2-10 9.0 229 3.1 1.488RSAPT-5CQ 88RSAPT-5C-3 5/16 M6 400 15-160 2-18 9.0 229 3.1 1.488RSAPT-2CQ 5/16 M6 200 15-180 2-20 9.8 248 3.4 1.5

Clecomatic Clutch

8, 88 SeriesTorque Range:

0.8 – 20 Nm7.0 – 180 In. Lbs

Screw Size:M3.5 – M6#8 – 5/16”

Bit and finder, quick change andsquare drive

Reversible

8RSAL–10BQ

88RSAPT-5CQ

8, 88 SeriesTorque Range:

0.8 – 19 Nm7.0 – 170 In. Lbs

Screw Size:M3.5 – M6#8 – 5/16

Bit and finder, quick changeand square drive

Short stroke button reverse

External torque adjustment(Quick change)

REVERSING SCREWDRIVERS & NUTRUNNERS

65

SCREWDRIVER ACCESSORIES

66

“CLICK” TYPE TORQUE SENSING WRENCHES

67

IMPACT WRENCHES (INDUSTRIAL & AUTOMOTIVE)

SQUAREDRIVE

WEIGHT(lbs) CAPACITY

PRICENEW

3/8”

3/8”

1/2”

1/2”

1/2”

3/4”

1”

3/8”

1/4”

KT81550

KT81560

KT81620

AP555

IR231C

IR261

IR285A-6

AP1139

AP1114 1

2-3/4

26

10-1/2

5-3/4

6

5

2-1/4

2-1/4

EXPERT REPAIR

ON ALL BRANDS

Bolt Cap: 3/8”Torque: 75 ft. lbs.






Bolt Cap: 1-1/4”Torque: 1450 ft. lbs.With 6” Extended Anvil

Overall Length: 10”Bolt Cap: 3/8”Torque: 50 ft. lbs.

Overall Length: 6-1/4”Torque: 30 ft. lbs.

RATCHET

68

AIR SANDERS

The Model 150 is the perfect sander forapplications where small size and light weightare needed. It features the same air motor andorbital sanding action as the Model 400, but asmaller pad size and 2/3 lb. less weight. Thatmeans more power per square inch of abrasivein an easy-to-handle tool and convenientsingle-handed operation.The Model 150 meets current OSHA noise levelstandards.APPLICATIONS INCLUDE:Feather edging • Finish sanding • Blending• Blocking

NATIONAL-DETROIT

DESCRIPTION: Heavy Duty Orbital Action Single Pad.SPECIFICATIONS: Ideal for metal or wood finishings.PAD SIZE: 3-1/2” x 6-1/2” PAPER SIZE: 3-2/3” x 9”

DESCRIPTION: Straight Line Action - Single PadSPECIFICATIONS: Built-in water attachment sprays water

directly on the work for wet sanding.PAD SIZE: 3-1/2” x 6-1/2” PAPER SIZE: 3-2/3” x 9”

DESCRIPTION: Dual Action: MODEL DA6SPECIFICATIONS: Provides scratch free sanding and

does not generate heat. Ideal for feather work.

MODEL DAQ6 same as DA except it has a lower noise levelPAD SIZE: 5”, or 6” PAPER SIZE: 5”, or 6”

DESCRIPTION: Straight Line ActionSPECIFICATIONS: Double Piston, reciprocating strokePAPER SIZE: 2-3/4” x 17-1/2”

DESCRIPTION: Dual ActionSPECIFICATIONS: -PAD SIZE: 5”, or 6” PAPER SIZE: 5” OR 6”

ECONOMY MODEL

PALM GRIP DUAL ACTION SANDERDESCRIPTION: Random Orbital ActionSPECIFICATIONS: Free Speed: 10,000 RPM

Air Inlet: 1/4”, Weight: 2-1/2 lbs.Avg. Air Consumption: 4.2 CFM

DESCRIPTION: 5” Hi-Speed SanderSPECIFICATIONS: Lightweight, 18,000 RPMPAD SIZE: 3”,4”,5” PAPER SIZE: 3”,4”,5”

EXPERT REPAIRS

ON ALL BRANDS

400

600

DA6DA6Q

EP 6017

AP 300

EP 6011

KT85265

150

69

AIR SANDERS

DOTCO® RANDOM ORBITAL SANDERS

70

SPECIFICATIONS

TYPICAL APPLICATIONSTOOLTYPE

BELTWIDTH GRIT

WEIGHTLBS.

NO LOADSPEED

REV/MIN

AIR CONSUMPTION

CFM

EP6014 16,000 .4 1-2/3EP6016 16,000 .55 3

EP6014 3/8”-13”EP6016 3/4”-13”

60, 80, 12060, 80, 120

Belt Sander

Sanding theinside of acut-out

Sanding into squarecorners

Sandinginside achannel section

Radius sanding

Surface sanding onflat belt pressure pad

Surfacesandingusing contactroller

12-18 SeriesNominal Motor Power

0.24 hp0.18 kW

Low profile for more sanding control

Lightest weight to reduce operatorfatigue

Extremely efficient built-in vacuumsystem with swivel hose fittings

3/16” & 3/32” random orbital pattern

Levers allow users to visually see thedifference between 3/16” and 3/32”machines3 interchangeable gripsto fit all hand sizes

Model Number SandingPad Size

Free Speedrpm

Weightlb. kgs.

Heightin. mm

Lengthin. mm3/16” Orbit 3/32” Orbit

12-18 Series – Random Orbital Sander – Non Vacuum

12-18 Series – Random Orbital Sander – Central Vacuum, Vacuum Attachment & Shroud

12-18 Series – Random Orbital Sander – Self-Generated Unit with Vacuum Hose & Floor Bag

12L1820-03 3.5” 12,000 1.56 0.71 3.33 84.58 5.11 129.7912L1820-05+ 12L1823-05+ 5.0” 12,000 1.62 0.73 3.33 84.58 5.48 139.1912L1820-06+ 12L1823-06 6.0” 12,000 1.68 0.76 3.33 84.58 5.48 139.19

12L1820-13 3.5” 12,000 1.60 0.73 3.33 84.58 6.98 177.2912L1820-15+ 12L1823-15 5.0” 12,000 1.73 0.78 3.33 84.58 7.75 196.8512L1820-16+ 6.0” 12,000 1.90 0.86 3.33 84.58 7.75 196.85

12L1820-25+ 5.0” 12,000 1.73 0.78 3.33 84.58 8.33 211.5812L1820-26+ 6.0” 12,000 1.80 0.82 3.33 84.58 8.84 224.54

MASTERFILEFINISHING TOOLKIT & MOUNTWhen you order the Masterfile kityou get flexibility and accuracy,because you’ll get the tool and all three interchangeable arms as well as the belts and wrenches that go with them.You’ll be ready for just about anyfinishing project when you get your hands on the Masterfile kit.

MASTERFILE KITMP4705K

1-Tool with 3/4” widestandard arm & 80 grit abrasive belt MP4705

1-3/4” open end wrench 704313001-9/16” open end wrench 704816001-3/16” Hex Wrench 70417600

1-9/64” Hex Wrench 704808001-1/4” Collet 704286001-Collet Cap 704284001-Collet Chuck 704285001-1/4 X 18 Coated 60 Grit

Abrasive belt 704680001-1/4 X 18 Coated 80 Grit






Abrasive belt 704735001-Non-woven nylon belt 704689001-Kit box with foam insert 704809001-1/2” wide standard arm 704807001-Offset Arm 70480200

Kit includes the following:

Model No.

MP-4705-1

Contact Arm

Straight

Length

15” (381mm)

Weight

2.5 lbs. (1.1kg)

Belt Size

5/8” or 3/4” W x18”L

Power

.51 HP (380 W)

Motor Speed

20,000 RPM

Belt Speed

4,550 SFPM (1382 SMPM)

ABRASIVE POWER TOOLS

71

DYNAFILE®

VERSATILE ABRASIVE BELT SANDER

No. 14000 . . .AIR POWERED BELT SANDER ONLY

No. 14010VERSATILITY KITIncludes 5 different Contact arms, No. 14000 Belt Sander and abrasive belts.

• Replaces tedious hand filing & sanding (4000 SFPM).• Lightweight and easy to use.• Superior belt tracking.• Uses 1/8”, 1/4” & 1/2” wide x 24” long belts• In addition to coated abrasive belts, non-woven nylon and

cloth polishing belts may be used.• Contact arms and belts changed easily without tools.

27 INTERCHANGEABLE ARMS FOR TOTALGRINDING AND POLISHING VERSATILITY

MINI-DYNORBITAL® SANDERAir tool uses fine grade discs for finesse sanding anddefuzzing wood.

ANGLE-HEAD PALM-STYLE

No. 53430 3,200 RPMUses 3/4” and 1-1/4” discs

No. 57500 5,000 RPMUses 3/4” and 1-1/4” discs.

TWO-HAND DYNORBITAL® SANDERLong Handle Random Orbital SandersAbrasive Capacity: 5” and 6” diameter discs.Provides better reach and comfort, especially when sanding vertical sides.

Non-Vacuum ModelsModel No. 58400 – 5” DiameterModel No. 58405 – 6” Diameter

Vacuum–Ready ModelsModel No. 58401 – 5” DiameterModel No. 58409 – 6” Diameter

*Provides excellent comfort and control , especially when workingon vertical sides of workpiece. Long Handle allows two-handedsupport of tool.

DYNAFILE® II – No. 40320POWERFUL, LIGHTWEIGHT ABRASIVE BELT SANDER• Work on metal, wood, plastic, fiberglass, etc.• Eleven interchangeable contact arms.• Uses 1/4”, 1/2” and 3/4” wide x 18” long belts.• Grinding head pivots to virtually any angle.

No. 40321 Versatility KitKit includes 40320Dynafile II, 3 different contact arms, abrasive belts, and 1/4” collet for converting motor to a die grinder.

LIGHTWEIGHT DYNORBITAL® – SPIRITAIR-POWERED RANDOM ORBITAL SANDER FOR SWIRL-FREE FINISHING ON METAL, WOOD, PLASTIC AND FIBERGLASS

Non-Vacuum5” Model No. 590206” Model No. 59025Low vibration: 12,000 RPM

Easy one-handed controlAdjustable speed.

Vacuum– Ready models accept a self-contained dust collection system!

PALM-STYLE – WEIGHSONLY 2.1 LBS

5” Model No. 590206” model No. 59025

DYNADIE® III – No. 12250

• Use on metal, wood, plastic, fiberglass, etc.

• Replaces tedious hand filing – enter narrow slots.

• Barrel indexes 360º for total operator comfort and control.

• Variable length stroke from 0-1/4”; 5,000 strokes per minute.

• Accepts 1/4” dia. Or 1/8” dia. shanked files. Order files separately.

• Built-in air-flow regulator.

• Thermal-insulated handle reduces cold air transmission to operator.

• Order files separately.

Uses 19 varietiesof superior quality Swisspattern files

FEATURES

Grind radius with belt over shaped contact wheel

Enter Narrow

Channels

Polish with unsupported part of belt

Work over Dynapad® platen

DOTCO® CARBIDE BUR & MOUNTED WHEEL GRINDERS/SANDERS

72

Model #: 12L1281-36

DOTCO® BELT SANDERS

“ECONOMY MODEL” ANGLE GRINDER/SANDERCOLLET RPM WEIGHT LENGTH

SIZE (Free Speed) (Ibs.)

REAREXHAUST EG5003C 1/4 20,000 1-1/4 5-1/4”

12L1280-36B6

12L1281-36B2

12L2887–13

DOTCO®

12-12,12-13 & 12-28 SeriesNominal Motor Power

0.3 & 0.9 hp0.22 & 0.67 kW

Rear ExhaustWoven & Non-Woven Belts

Model Number Sanding Belt Free Speed Weight Length

Front Exhaust Rear Exhaust Capacity rpm lbs. kgs in. mm

* MOST POPULAR MODELS – RAPID SELECT MEANS FAST DELIVERY

!Tools must be ordered with lock-off lever throttleto be CE compliant. See ordering details below.

12-12 Series – 0.3 hp (0.22 kW) – Non-Woven Belt12L1200-36B6 12L1280-36B6 1/2” x 18” 12,000 1.8 0.8 15.6 396

12-12 Series - 0.3 hp (0.22 kW) - Sanding Belt12L1201-36B1 12L1281-36B1 1/4” x 12” 20,000 1.4 0.6 11.3 28712L1200-36B1 12L1280-36B1 1/4” x 12” 12,000 1.4 0.6 11.3 28712L1201-36B2* 12L1281-36B2 1/2” x 12” 20,000 1.4 0.6 11.3 28712L1200-36B2* 1211280-36B2 1/2” x 12” 12,000 1.4 0.6 11.3 28712L1201-36B4 12L1281-36B4 1” x 12” 20,000 1.7 0.8 11.3 28712L1200-36B4 12L1280-36B4 1” x 12” 12,000 1.7 0.8 11.3 28712L1201-36B3 12L1281-36B3 1/2” x 24” 20,000 1.6 0.7 16.4 41712L1200-36B3 12L1280-36B3 1/2” x 24” 12,000 1.6 0.7 16.4 41712L1201-36B5 12L1281-36B5 1” x 24” 20,000 2.2 1.0 16.4 41712L1200-36B5 12L1280-36B5 1” x 24” 12,000 2.2 1.0 16.4 417

12-13 Series - 0.3 hp (0.22 kW) - Gearless - Sanding Belt12L1382-36B1 1/4” x 12” 20,000 1.4 0.6 11.3 28712L1382-36B2 1/2” x 12” 20,000 1.4 0.6 11.3 28712L1382-36B4 1” x 12” 20,000 1.7 0.8 11.3 28712L1382-36B3 1/2” x 24” 20,000 1.6 0.7 16.4 41712L1382-36B5 1” x 24” 20,000 2.2 1.0 16.4 417

12-28 Series - 0.9 hp (0-.67 kW) - Sanding Belt12L2887-12 1/2” x 12” 18,000 2.6 1.2 12.5 31812L2887-13 1” x 12” 18,000 2.8 1.3 12.5 31812L2887-24 1” x 12” 18,000 3.4 1.5 18.8 478

73

AIR SANDERS & GRINDERSEXPERT REPAIRS

ON ALL BRANDS

KT87125

Model #: 12L2252-80

Model #: 12L2752-80

74

DOTCO® MINIATURE PRECISION TOOLS

Model #: 10R0401-18

Model #: 12RO410-18Standard With Sleeveand Collet Guard

Standard With Collet Guard

Model #: 12R0380-18

75

DOTCO® CARBIDE BUR & MOUNTED WHEEL GRINDERS

Model #: 12L2580-01

Model #: 12L2080-01

Model #: 12L1001-36

76

GRINDERS

Dotco® miniature precision tools

10-11 Series

12-11 Series

12-26 Series

18,000 – 28,000 RPM

0.3 – 1.2 hp (0.22 – 0.9 kW)

Extended housings

Aluminum, composite or ruggedsteel housings

Inline Extended GrindersFor Carbide Burrs, Mounted Points, Mounted Wheels

STANDARD EQUIPMENT:Applicable collet, collet wrenches

MULTIPLE EXTENSIONS FOR 12-26 SERIES:Each extension changes the tool length and weight by:12-26 series = 7.25” (184mm) and 1.2 lbs. (0.54 kg);The length and weight in the table are for 2A models

1A = One extension2A = Two extension3A = Three extensions, etc.

All multiple extensions are not available in all speeds

Housing Guide: A=Aluminum, C=Composite, S=Steel*Governor controlled speeds

‡Mounted wheel capacity depends on wheel diameter, thickness andoverhang. Consult wheel manufacturer for speed recommendations.

GENERAL:All tools performance rated @ 90psi (620 kPa) air pressure.Minimum Hose I.D.–

10-11, 12-11 Series: 1/4” (4.8mm)12-26, 136 Series: 5/16” (7.9mm)

FreeSpeed Type

HousingWeight

lbs. kgs

Length

in. mm

ColletSize

AirInletSizerpm Abrasives CapacityFront Exhaust Side Exhaust Rear Exhaust

Model Number

12-11 Series - 0.3 hp (0.22 kW) - 5” (127mm) Extension - 300 Series Collet

10-11 Series - 0.3 hp (0.22 kW) - 5” (127mm) Extension - 300 Series Collet

12-26 Series – 0.9 hp (0.67 kW) – Multiple Extension - 300 Series Collet

12L1101-36 12L1181-36 28,000 1/2” Carbide Burr, 1” Mtd. Wheel C 1.3 0.6 10.9 277 1/4” 1/4”12L1112-36• 25,000 1/2” Carbide Burr, 1” Mtd. Wheel C 1.3 0.6 10.9 277 1/4” 1/4”

10L1101-36 10L1181-36 28,000 1/2” Carbide Burr, 1” Mtd. Wheel A 1.2 0.5 9.8 248 1/4” 1/4”

12S2674-2A• 18,000 3/4” Carbide Burr, 11/2” Mtd. Wheel C 4.2 1.9 23.5 597 1/4” 1/4”

77

HUTCHINS AIR SANDERS & GRINDERS

Final Finishing

Water Sanding

Primary Material RemovalModel 3500 SUPER SANDER IIIRANDOM ORBIT ACTION.Designed for today’s needs. The SuperSander III offers the same ultra-fine finishingas the 4500 in a lightweight-low profile configuration. Composite motor housing and shroud reduce weight and insulate theoperator from vibration. Ultra smooth motorwith positive action drive and unique 4 bearing support insures full contact sanding.Oversized drive head eliminates pad wobble.Built-in pad release feature.

Model 2000 VA/DF HUSTLERSTRAIGHTLINE RECIPROCAL ACTION. 2-Cylinder, oversized common piston, powers twin-drivevertically-engaged gears with synchronized strokes so smooth that the 2000 VA/DF gets lighter with use.Precision-built, the HUSTLER does almost anything butfinish and paint the surface. Rugged, but almost delicatein performance. With VA/DF options it becomes thehealthiest, most productive straightline available.

RANDOM ORBIT ACTION. The 3560 is amore aggressive version of the Model 3500for those looking for rapid material removalin a light weight-low profile configuration.The composite motor housing and shroudreduce weight and insulate to insure vibration - free sanding. The unique 4 bearing support and oversized drive headeliminate pad wobble while insuring fullpad contact. Includes a patented padrelease feature.

ORBITAL ACTION. World’s most versatile water sander. 20’ High-PressureWater Hose with filtered, venturi-generated flow, guarantees effective watersanding anywhere. Just drop the hose in any appropriate water container, adjustthe flow - and do it! New High Performance Motor using balanced rotor with 2-piece self-expanding vanes for unexcelled torque provides constant power for any sanding need. Unique bypass system protects all motor components frommoisture ensuring long-life productivity. Features a medium-density pad for all preliminary sanding needs, then use the Interface Pad for superb finish sandingand removal of defects in clear coats. Comes complete with General Purpose Pad, Interface Finishing Pad, and 20’ H.P. Water Hose. Two Pad sizes: 3-2/3" X 7" and 6" Pad (round) available.

Model 3560

7044 & 7044-6“WATER BUG II”

SERIES:

Model 3500 Part No. 3500 6” PSA Pad Std. Part No. 3500H 6” Hookit Pad

Pad size 2 3/4” X 16”Pierce platePart No. 1992 Optional

RPM: 10000+Wt: 2lbs. 3.5 oz.Air Consumption: 11.0

cfm @ 90 PSINoise Level: 80 dBa

SPM: 3000Wt: 6lbs. 2 oz.Air Consumption: 6.2


Model 3560 Part No. 3560 6” PSA Pad Std. Part No. 3560H 6” Hookit Pad

Part No. 7044 – Pad size 3 2/3” X 7” (Paper 3 2/3” X 9”)Part No. 7044-6 – Pad size 6” round (Velcro)

RPM: 10000+Wt: 2lbs. 3.5 oz.Air Consumption: 11.0


RPM: 8500+Wt: 4lbs. 1 oz.Air Consumption: 10.4


Part No. 7044

Vacuum Extraction

78

SEE PG. 85

FOR

CUT-OFF

TOOL

Part No. 50690

ABRASIVES

79

100

100

100

QUICK CHANGE SOCATT LAMINATED DISCS

80

CARBIDE ROTARY FILES

HIGH SPEED STEEL AVAILABLE 81

ROUTERS

ROUTERS ACCESSORIES

ROUTERS GUIDES FOR 1/4 ROUTER BITS

82

ECONOMY MODEL

New! ErgonomicSafety Lever

Router AssembliesFor use with Dotco 12-10, 12-20 and 12-25 series.

12-10 1/4” 14-2187 14-2176 14-0508 1098 14-2082 14-118012-20/12-25 1/4” 14-2180 14-2176 14-0508 1098 14-2082 14-218012-20/12-25 3/8” 14-2429 14-2426 14-0533 1068 14-2082 14-218012-12/12-22/12-27 1/4” 7197 14-0508 1098 N/A N/A

Tool Series Bearing Ring Lock Nut RouterHousing

Part NumberCutterShank

CapacityComplete

AttachmentNose

Housing*

14-2180

+.000–.010

+.000–.010

1/2–20 NF

`281” DIA.A B

D

1/4C

AttachmentNumberIncluded

AttachmentNumberIncluded

DOTCO® ROUTERS

83

Series 10-43Model #: 10T4318-62

Series 10-40

Series 12-25

SAWS

84

12L-2065-90

Mini Air Saw

BOSCH AIR JIG SAWNo. 0607561-120

No. IR429

Cuts in confined areas are made simple and easy. It performs well on straight and curved surfaces, pipe,

mild steel, aluminum, plastic and fiberglass.

SPECIFICATIONS

• Avg. Air Consumption: 6 C.F.M.

FP 5650 Assorted Saw Blades 10 pcs., H.S.S.

• Strokes Per Minute: 9000 • Weight: 1-3/8 Lbs.• Length: 9-1/4” • Air Inlet: 1/4”

* Orbiting blade action provides optimum cutting efficiency.* Four position adjuster gives the ideal blade orbit for each job.* Base plate can set to any angle up to 45º* Set of three different saw blades are supplied to suit a variety of applications and materials.* Powerful 0.54 HP motor provides smooth cutting action, 2200 RPM.

AIR-SPEED RECIPROCATING SAW & FILE

#HS125 – HEAVY DUTY . . . . . .• Fully Portable Saw• Cuts Steel, Stainless & Aluminum• Front Barrel Can Be Turned 360º For Access Into Tight Areas• Regulating Throttle That Locks Into Tight Areas• Adjustable Blade Strokes Range Of 1/2” – 1-1/4”• Regulating Throttle That Locks Into Designated Speed• 4-1/2 lbs.

(Set of 4” blades — 14, 18, 24, 32, Tooth —

UTILITY CUT–OFF TOOL

Slices through sheet metal, bolts and steel rodsSpecifications:

#122060 ... cut off wheel only

Model Number

KT88255

FreeSpeed-rpm

20,000

Weightlb.

1-3/4

LengthIn.

7

AirInlet

1/4”

RECIPROCATING SAW MILWAUKEE

SIOUX

ELECTRIC

AIR

CatalogNumber

6509-22

Stroke

3/4”

SX1300 5/8” 1800 17-1/8 7 13

in Metal Box

Strokesper

minute

0-2800

OverallLengthInches

16”

LoadSpeedAmps

10

Hose connection

1/4” PT

Net WeightTool Only Lb. Oz.

7

Metal & Wood Blades Available

OSCILLATING SAWS

Nominal .6 HP – rear ExhaustCapacity: 2” or 2-1/2”” Saw Blades

Ergonomic Series 12-22

SEE PG. 79FOR CUT–OFFWHEELS

AIR

DOTCO® SAWS

Model #: 12S2749-01

Model #: 12S2794-02

Model #: 12S1283-02

85

DOTCO® SAW ACCESSORIES

86

KETT PORTABLE POWER PANEL SAWS

87

CUTTING TOOLS

88

Max Cutter Cap 5/8

A

D

.086 Specify

CARBIDE COUNTERSINKS

150CT SERIES...These countersinks excel in cutting highlyabrasive materials. “The difficult-to-machine”materials, and in cutting material where longertoo life is desired. The tool body is made ofhigh speed steel. Two flute 100° angle isstandard.

150 SC SERIES...These countersinks are similar in design to the150CT Series, except that this tool is made withsolid carbide head butt brazed to steel shankgiving pilot equal wear resistance to cutting edge.100° angle is standard. Special angles subjectto quote.

CARBIDE TIPPED STOP COUNTERSINK

Integral pilot, threaded shank

SOLID CARBIDE STOP COUNTERSINK

Integral pilot, threaded shank

150 CT SERIES

150 SC SERIES

HOW TO ORDER THREADED SHANK INTEGRAL PILOT COUNTERSINK CUTTERS

When ordering please specify: Tool number, Number of flutes, materialInclude angle and Pilot diameter

Example: 152-CT-100° -3/16 = 1/2 x 100° x 3/16, Carbide tipped, 1/4-28, 2 fluteStandard pilot diameters: 3/32, 1/8, 5/32, 3/16, 1/4, 5/16, 3/8, 7/16, 1/4, #40, #30, #21, #11, #10

89

TOOL

NUMBER

151 CT

152 CT

153 CT

155 CT

156 CT

157 CT

“D”

BODY DIA.

7/16

1/2

5/8

3/4

7/8

1

“S”

SHANK SIZE

1/4-28

1/4-28

1/4-28

3/8-24

3/8-24

3/8-24

PILOT

RANGE

3/32-3/16

3/32-1/4

5/32-5/16

1/4-3/8

1/4-7/16

5/16-1/2

TOOL

NUMBER

151 SC

152 SC

153 SC

155 SC

156 SC

157 SC

“D”

BODY DIA.

7/16

1/2

5/8

3/4

7/8

1

“S”

SHANK SIZE

1/4-28

1/4-28

1/4-28

3/8-24

3/8-24

3/8-24

PILOT

RANGE

3/32-3/16

3/32-1/4

5/32-5/16

1/4-3/8

1/4-7/16

5/16-1/2

CUTTING TOOLS

MM 276 Pilots are for usein the MM 275 counterbores.Made from heat treated toolsteel and precision groundto insure concentricity andsize tolerances. Carried instock in the sizes shown.

Example: MM 276-2 A for 1/8 pilot x 1/8 shank

COUNTERBORE PILOTS

COUNTERBORES

WHEN ORDERING PLEASE SPECIFY PART NUMBER AND SHANK DIAMETER -A OR -CREFER BELOW TO THE RANGE OF PILOT DIAMETERS FURNISHED WITHEACH SIZE PILOT SHANK.

MM 275 Counterbores are foruse in portable drill motors anddrill presses. Quality made ofhigh speed tool steel, properlyheat treated and precisionground to insure free cutting.Corner radii ground to aircraftstandards. Refer to MM 276for pilots. Carried in stock inthe sizes shown.

#275K25 COUNTERBORE KIT

25 Pcs. in Plastic CaseSize: 1/4”-1” by 1/32 grad.

25 Pcs. As Above Plus 20Assorted Pilots

13 Pcs. in Plastic CaseSize: 1/4”-1” by 1/16 grad.

13 Pcs. As Above Plus 10Assorted Pilots

#275K13 COUNTERBORE KIT

#275K23P COUNTERBORE KIT#275K45P COUNTERBORE KIT

P

D

L

3/8” 1/4”

thru 1” cutter diameter

1 7/16” thru 1 1/2” cutter diameter

D

SHANK SIZE

90

CARBIDE TIPPED AIRCRAFT COUNTERBORES

850 SERIESReplaceable pilot, straight shank

850-1 1/4 3/32 1/4 2-3/8850-2 9/32 3/32 1/4 2-3/8 850-3 5/16 3/32 1/4 2-3/8850-4 11/32 3/32 1/4 2-3/8850-5 3/8 3/32 1/4 2-3/8850-6 13/32 1/8 1/4 2-3/4850-7 7/16 1/8 1/4 2-3/4850-8 15/32 1/8 1/4 2-3/4850-9 1/2 1/8 1/4 2-3/4

850-10 17/32 1/8 1/4 2-3/4850-11 9/16 1/8 1/4 2-3/4850-12 19/32 1/8 1/4 2-3/4

850-13 5/8 1/8 1/4 2-3/4850-14 21/32 3/16 1/4 2-3/4850-15 11/16 3/16 1/4 2-3/4

850-16 23/32 3/16 1/4 2-3/4850-17 3/4 3/16 1/4 2-3/4850-18 25/32 3/16 1/4 2-3/4

850-19 13/16 3/16 1/4 2-3/4850-20 27/32 3/16 1/4 2-3/4850-21 7/8 3/16 1/4 2-3/4

850-22 29/32 3/16 1/4 2-3/4850-23 15/16 3/16 1/4 2-3/4850-24 31/32 3/16 1/4 2-3/4

850-25 1 3/16 1/4 2-3/4850-26 1-1/16 3/16 3/8 2-3/4850-27 1-1/8 3/16 3/8 2-3/4

850-28 1-3/16 3/16 3/8 2-3/4850-29 1-1/4 1/4 3/8 2-3/4850-30 1-5/16 1/4 3/8 2-3/4

850-31 1-3/8 1/4 3/8 2-3/4850-31B 1-7/16 1/4 3/8 2-3/4850-32 1-1/2 1/4 3/8 2-3/4

850-33 1-9/16 5/16 1/2 3-1/16850-34 1-5/8 5/16 1/2 3-1/16850-35 1-11/16 5/16 1/2 3-1/16

850-36 1-3/4 5/16 1/2 3-1/16850-37 1-13/16 5/16 1/2 3-1/16850-38 1-7/8 5/16 1/2 3-1/16

850-39 1-15/16 5/16 1/2 3-1/16850-40 2 5/16 1/2 3-1/16

TOOL NUMBER

"D" CUTTER DIA.

"PH"PILOT HOLE DIA.

"S" SHANK DIA.

O.A.L.OVERALL LENGTH

850 SERIES carbide counterbores are similar in designto the 275 Series highspeed steel cutters. They excel incutting highly abrasive materials, and are recommendedfor counterboreing and spot-facing the ”difficult tomachine” and ”exotic” materials in which high speedsteel will not perform satisfactorily. Also recommendedfor any application where longer tool life is desired.

Special ”D” cutter diameters may be readily groundfrom standard sizes listed. Special cutters given prompt attention.

All cutters furnished with 1/64 corner radius. Maximumnon-cutting diameter is 1/32 larger than the pilot hole.Recommend using pilots with ”H” head diameter 1/32minimum larger than ”S” shank diameter. For pilot information see MM276 Series.

91

CUTTING TOOLS

BACK SPOTFACER CUTTER KIT

BACK SPOTFACER CUTTERSMM 280 Back spotface cutters are made from high speedtool steel properly heat treated and ground with properclearances to insure free cutting. Corner radii, ground toaircraft standards. For use in restricted areas whereconventional type spotfacing cutters cannot be used.

MM 285 Pilots are made from tool steel, heat treated on working end, andground to insure free operation in holes to be countersunk or spotfaced.For use with MM 280, MM 290 and MM 295 cutters. Step type pilots, tocustomer’s specifications, will be supplied on special order.

Bayonet lock type

TOOL NO. DIAMM 280-1JMM 280-1KMM 280-2KMM 280-2LMM 280-3KMM 280-3LMM 280-4K

MM 280-4LMM 280-5KMM 280-5LMM 280-6KMM 280-6LMM 280-7KMM 280-7L

7/16”1/2”1/2”9/16”9/16”5/8”5/8”

1/4”1/4”5/16”5/16”3/8”3/8”7/16”

PILOTSIZE3/32”1/8”1/8”5/32”5/32”3/16”5/32”

3/16”3/16”1/4”3/16”1/4”1/4”5/16”

BACK SPOTFACER CUTTER KITIncludes:

all MM 280 Backspotfacer cutters1/4” through 5/8”

with 6 Pilots in Box#280K20...............................

BAYONET PILOTS FORBACKSPOTFACERS

AND COUNTERSINKS

CARBIDEAVAILABLE

SEE PAGE 94

92

BACK COUNTERSINK CUTTER KIT

MM290 Back countersink cutters aremade from high speed tool steelproperly heat treated and ground withproper clearances to insure freecutting. For use in restricted areaswhere conventional typecountersinking tools cannot be used.

HIGH SPEED STEEL• For collar removal on Hi-Shear

and Huck Fasteners• 1/4” x 28 Male Threaded Shank

TOOL NO. DIA

MM290-1JMM290-1KMM290-2KMM290-2LMM290-3KMM290-3LMM290-4K

MM290-4LMM290-5KMM290-5LMM290-6KMM290-6LMM290-7KMM290-7L

7/16”1/2”1/2”9/16”9/16”5/8”5/8”

1/4”1/4”5/16”5/16”3/8”3/8”7/16”

PILOTSIZE3/32”1/8”1/8”5/32”5/32”3/16”5/32”

3/16”3/16”1/4”3/16”1/4”1/4”5/16”

BACK COUNTERSINK CUTTER KITIncludes:

all MM290 Countersink cutters1/4” through 5/8”

with 6 Pilots in Box#290K20...............................

COLLARREMOVAL CUTTERS

WHEN ORDERINGPLEASE SPECIFY PARTNUMBER AND A-DEGREE.FOR PILOTS REFERTO MM 285.SEE PAGE 92.

SPECIAL DIAMETERSAND PILOT HOLE SIZESAVAILABLE ON SPECIALORDER.

(20 PIECES)

THREAD

APilot Size D

DA

CARBIDEAVAILABLE

SEE PAGE 94

O

93

CUTTING TOOLS

BACK COUNTERSINK CUTTERSBayonet lock type

CARBIDE REVERSE COUNTERSINKS AND SPOTFACERS

94

181 SERIESCARBIDE REVERSE COUNTERSINKS

191 SERIESCARBIDE REVERSE SPOTFACERS

181 SERIES…These carbide reverse countersinks excel in cuttinghighly abrasive materials, the “difficult-to-machine”materials* and in cutting any materials where longertool life is desired. Standard in three flutes with 100º countersink angle.

191 SERIES…These spotfacers excel in cutting highly abrasivematerials, the “difficult-to-machine” materials, and in cutting any material where longer tool life is desired. All carbide cutters are supplied with1/64 corner radius.

When ordering please specify: Tool number and included countersink angle.Example: 181-5J-100º

CUTTING TOOLS

CARBIDE CUTTING TOOLS

95

755 SERIES

700 SERIES 730 SERIES

3N1™ DRILL POINT COUNTERSINKS

PART NUMBERSSHOWN AREFOR CARBIDE

96

PILOTED COUNTERSINKS

97

AIRCRAFT HOLE SAWS

98

COMPOSITE TOOLS

99

Shearbore Carbide DrillsFOR USE IN KEVLAR, FIBERGLASS, BORON, PLASTIC,

CARBON & OTHER HIGHLY ABRASIVE MATERIALS

COMPOSITE TOOLS

100

Polycrystalline Diamond/C.B.N.Special Rotary Cutting Tools and Plated Diamond

Special Rotary Cutting Tools

EVERSINKS

101

EverSinks are the world’s most complete replaceable insert countersink system. The integralpilot design allows for simple insert mounting that permits a repeatable relationship betweenthe countersink and the fillet radius in one operation.

Other attributes include:• Carbide and PCD tipped insert configurations available.• 100° and 130° bodies standard; other angles quoted on request.• Cam lock and screw down insert types available.• All standard fillet radii available. Double angle chamfer inserts also available.• Single and two flute configurations available. Note: 2 flute bodies must

have at least .150 (3.8mm) pilot.• Removable pilot bodies available for .125 (3.2mm) hole diameters and larger.• Eversink bodies are made from wear resistant heat treated tool steel.

101501 or 101501-LCam Pin

19035 Insert Screw

Cam-Lock Eversink Numbering System

2-Flute Bolt-On Eversink Numbering System

6 1 8 7 0 1

2 – 6 1 8 7 0 1

BODY DIA.6 = 5/87 = 3/48 = 7/89 = 1”

BODY DIA.6 = 5/87 = 3/48 = 7/89 = 1”

C’ SINK ANGLE8 = 82°9 = 90°

1 = 100°3 = 130°

C’ SINK ANGLE8 = 82°9 = 90°

1 = 100°3 = 130°

Add “DS” for bodies using aradius or double-chamfer PCDtipped insert

Add “D” for bodies using astraight PCD tipped insert

Add “D” for bodies using astraight, radius or double-chamfer PCD tipped insert

PILOT DIA.(middle 4 digits)

PILOT DIA.(middle 4 digits)

2 FLUTES

Eversink Insert Numbering System

C’ SINK ANGLE8 = 82°9 = 90°

1 = 100°3 = 130°

Add “DC” for anyPCD tipped insert

RAIDUS, CHAMFER ANGLE or“000” for STRAIGHT INSERTS

INSERT TYPER = RADIUS

C = CHAMFERS = STRAIGHT

INSERT STYLEIB = BOLT ON

IC = CAM LOCKIX = “X” STYLE

BODY DIA.6 = 5/8”

7 = 3/4, 7/8 & 1”

I B 6 1 R 015

E

SEALANT GUNS

All Semco retainersare 100 psi pressurerated and designed foruse with Semco guns,cartridges, and dispensing systems.

250 Retainers

Hose Assemblies

HOSE CONNECTORS

All hose assembliescome with a B-nutfitting to attachto the Semco gun orequipment and thespecified quick disconnect attachment

HANSENHose Assy.

SCHRADERHose Assy.

AROHose Assy.

MANUALSEALANT GUNThe manual gun has a smoothpluger rod. A simple touch on the leverreleases pressure instead of difficult twistingand turning of the rod. Since there are no rodnotches, you can dispense any amount of material.Threaded collar holds cartridge. Gun does notinclude cartridge or nozzle. Two models have different rod lengths for different size cartridges.

MODEL 1832-6 for 2-1/2 and 6 ounce cartridges...

MODEL 1832-12 for 12 ounce cartridges...............

MODEL 12050 - Includes 1832-6 manual gun,assorted nozzles and six 2-1/2 oz. cartridges........

MODEL 12051 - Includes 1832-6 manual gun,assorted nozzles and six 6 oz. cartridges..............

MODEL 12052 - Includes 1832-12 manual gun,assorted nozzles and six 12 oz. cartridges............

The 950 Series Sealant Guns are manufactured from the highestquality materials to assure long life and easy, dependable operation.Gun bodies and handles are made of durable, lightweight aluminum.The corrosion resistant retainers are made of a special high strengthsteel to prevent a cartridge splitting under high pressures.To load, simply turn the knob and disengage the retainer. Insert thefilled cartridge, replace the retainer with cartridge and then tightenthe knob. To operate, simply pull the trigger to open the air valve. Airenters through the valve and forces the plunger down the inside of thecartridge displacing material out of the nozzle. The result is a smooth uniform flow of material applied exactly where you want it. Each gunincludes one retainer, cartridge and plunger.

AIR OPERATED SEALANT GUNOperate on air line pressures from 5 to 150 p.s.i.

AIR OPERATEDSEALANT GUN KITS

All kits include an air hose, pistol grip gun, six cartridges, plunger, caps

and a selection of nozzles.NOTE: Must specify type of airline connector

Model 12053A 2-1/2 oz......................Model 12054A 6 oz......................Model 12055A 12 oz..........................

NOTE: Tool includes one cartridge, plunger & retainer.Order air hoses seperately.

Model

950-25 A

950-25 HA

950-60 A

950-60 HA

950-120 A

950-120 HA

CapacityOz.

2 1/2

2 1/2

6

6

12

12

HandleType

PALM

PISTOL

PALM

PISTOL

PALM

PISTOL

Description1 oz.2.5 oz.6 oz.8 oz.12 oz.

Part Number231611220256220928220926220923

Description5 ft. Aro hose assembly10 ft. Aro hose assembly5 ft. Hansen hose assembly10 ft. Hansen hose assembly5 ft. Schrader hose assembly10 ft. Schrader hose assembly

Part Number280012280013280000280001280006280007

102

103

COMPLETE LINE OF VIRGIN POLYETHYLENE NOZZLES, CARTRIDGES AND ACCESSORIES

Valve Protector

#1859-3 .............

HAND TOOLS

104

PLATE NUT DRILL JIG

MANY OTHER SIZES AVAILABLE

105

ULTRALITE NUTPLATE DRILLMOTORS

hi-shearC O R P O R A T I O N

One hand operation to locate, drill and countersink bothrivet holes in a single 4 second operation.Tool is easily converted from one rivet hole spacing to another byinterchanging the foot attachments and spindle spacer block.

0.500 inches600 and 7,000 RPM0.001 to 0.012 inches per rev.0.54 HP18 CFM at 90 PSI0.250 inch4.75 lbs.

Drill stroke length:Available spindle speeds:

Feed rate range:Motor power:

Maximum air consumption:Collet stroke length:

Weight:

Specifications

106

The Spacematic ULTRALITE® Nutplate Drill Motor IIis a pneumatic portable hand held tool that drillsand countersinks the two rivet holes which aresubsequently used to mount various types of nutplates. The tool is completely automatic in that operation consists of inserting the collet-mandrel assembly into the pre-drilled pilot hole and activating the trigger. The collet-mandrelassembly grips the work piece, holding the toolsecurely while both drill-countersincks are simultaneously rotated and advanced into the workpiece under controlled feed conditions. When bothdrill-countersinks have reached their pre-set depth,releasing the trigger completes the cycle.

OPTIONS

All Spacematic Nutplate Drill Motor IIs have the VARIABLE SELECTION feature of completely interchangeable, standard foot assemblies, spacer blocks, collet-mandrels, spindle assemblies, drills and RPM gear changes. These options configure a given tool to have drill-countersink capacity for producing the rivet mounting holes for 234 different types (sizes) of nutplates.

NUTPLATE DRILLSHIGH SPEED AND COBALT

NPD DRILL COUNTER SINKSfor Nutplate Drillmotors

LengthDash No.

-25*-35-50

“L”Dim.295.420.560

WHEN ORDERING SPECIFYSeries No. – C’Sink Angle–Length Dash No.

EXAMPLE: NPD40–100–35–8Standard NPD40 drill countersink made of

M2 H.S. steel is used for drilling aluminum and mild steel.add prefix M3 if cutters are to be used for drilling hard steel.

SeriesNo.

NPD40NPDS40NPD30

NPDS30NPD21

NPDS21

Body and C Sink Dia.

.187

.250

.250

.313

.313

.375

DrillDia..098.098

.12851285 .159.159

2.490 “L”

10-32 or 8-32 Body Dia. Drill Dia.

C’ Sink Angle

HANDTOOLS

HANDSEAMER

ALUMINUMSNIPS

VISE-GRIP

CAMLOC PLIER WISS AVIATION SNIPS

PLIERS

Wide, deep jaws machined for smoothparalled fit. Forms precise folds andseams. Throat 1” deep x 3 1/2” wide.

# 44

# M12A…(12” 0.A.L., 1 Lb.)

# M14A…(14” 0.A.L., 1.5 Lb.)

# 4P3… # AAT508K

M1R Left cut…red grips

M2R Right cut…green grips

M3R Straight cut…yellow grips

Made in USA

# 81…# 81A (replacement Punch)….• Hand Operated• Cuts Sheet Metal Like a Punch & Die• Ideal for Templets, Shims & Radio• Chasis Capacity 186Ga Alum• 7 oz.

ADEL HAND NIBBLING TOOL

OFFSETSNIPS

Cutting Application

Snips cuts sharp leftangle, straight line,and 5” dia. left circles

Snips cuts sharpright angle, straight line,and 5” dia. Right circles

Grips

red

green

Number

20 SL

20 SR

Length

9”

9”

Net wt.

15 oz.

15.oz

Superior quality. Heavy duty snips areonly 1/3 the weight of steel types andgive many more years of service.Comfortable, sleek contour aluminumhandles have reinforcing ribs to duplicate the strength of steel.Handles will not spring when cuttingheavy gauges of sheet metal. Inlaidblades are supreme cutlery grademoly steel, electronically heat treatedand tempered for continuous use.Precision ground, beveled cuttingedges stay sharp longer and makepattern and circle cutting an easy job.

Cannon Connector, non-sparking, high-strengthzinc aluminum alloy, slip-joint handle, replace-able serrated plastic jaws.

• Strong & lightweight with inlaid steel blades

• Resharpenable blades that replaceeasily when necessary

• Metallic gray, black enamel finish

10R 10” Straight Jaw Locking Pliers7R 7” Straight Jaw Locking Pliers10CR 10” Curved Jaw Locking Pliers7CR 7” Curved Jaw Locking Pliers10WR 10” Curved Jaw Locking Pliers w/Cutter7WR 7” Curved Jaw Locking Pliers w/Cutter5WR 5” Curved Jaw Locking Pliers w/Cutter4WR 4” Curved Jaw Locking Pliers w/Cutter9LN 9” Long Nose Locking Pliers6LN 6” Long Nose Locking Pliers4LN 4” Long Nose Locking Pliers6R 6” Locking “C” Clamp Pliers11R 11” Locking “C” Clamp Pliers18R 8” Locking “C” Clamp Pliers24R 24” Locking “C” Clamp Pliers4SP 4” Locking Clamp w/Swivel Pads6SP 6” Locking Clamp w/Swivel Pads11SP 11” Locking Clamp w/Swivel Pads24SP 24” Locking Clamp w/Swivel Pads506QC 6” Quick Change Bar Clamp/Spreader512QC 12” Quick Change Bar Clamp/Spreader518QC 18” Quick Change Bar Clamp/Spreader524QC 24” Quick Change Bar Clamp/Spreader

107

HANDTOOLS

SAFETY WIRE TWISTER TOOLS

TUBE BENDERS(Lever Type)

37° ROL-AIR® FLARING TOOL#507FB……………………

LEVER-TYPE BENDERS

SAFETY WIRETWISTERS(With Spring Return)

HANDY – CONVENIENT

STAINLESS STEELAIRCRAFT SAFETYWIRE

For Bending Annealed Copper,Aluminum, Steel, Stainless Steel and Hard Copper Tubing of BendingTemper (including K Types, L andACR).

Each tool bends one size. Open side type which slips over tube at anypoint. Makes smooth short radius bends up to 180°with minimum effort.No marking, scraping or flattening of tubing. Calibrated to show angle ofbend. Wide hook grips tubing securely.New fixed hook tube benders furnished for 1/4 to 1/2” O.D. sizes haveeasy 90° start – require much less effort to make fast, accurate bends.Wide fixed hook simplifies operation, holds tubing securely.Each tool bends only one size

Three-in-one tool: plier, twister, and cutter. Usedon wire sizes .060 or less. Grips wire into 30 slip-proof angle. One-hand operation. 10” O.A.L

#68……………………….…..#68B Endbearing………….

#C32. . . . ( .032 Diameter )#C41. . . . ( .041 Diameter )#C21. . . . ( .021 Diameter )

• 1 lb. Spool• 302 MS — 20995–C Stainless Steel Wire ( Conforms to Mill Spec W6713)

CatalogNumber

364–FHB–04364–FHB–05364–FHB–06364–FHB–07364–FHB–08364–FHA–10

Diameter of tubing

1/45/163/87/161/25/8

Weight Each

1 lb.1-1/8 lbs1-3/4 lbs.3-1/2 lbs.3-1/2 lbs.5-1/2 lbs.

OutsideNominal

Size

1/8–

1/4–

3/81/2

Radius ToCenter of

Tube

3/1611/1414/161-1/21-1/22-1/4

Flares and burnishes 3/16”, 1/4”, 5/16”, 3/8”, 1/2” and 5/8” O.D. tubing

Flare soft copper, aluminum and brass.Faceted, hard chrome finished cone

rolls out perfect 37° flaresabove die block—then auto-matically burnishes flare face.Original wall thickness main-tained at base of flare Slip-onyoke permits use in tight quarters. Heat treated diesgrip tubing without scoring.

HEAVY-DUTY TUBE CUTTERFor 1/8” to 1-1/8”

Tubing

PARKER–TYPEBEADING TOOL SET

TC1000………….……….…..

For Beading Tubing1/4” to 1”

Model# AP145

The Parker Beading Tool has been the #1 choice for mechanics for makinghose-clamping beads in metal tubes. New enhancements include ground,hardened and polished surfaces for mar-free beads in aluminum, copper, brass and mild steel tubes ranging from 1/4” to 1” diameter. Meets MILSPECMS33660D and SAE AS5131 standards. Kit contains 1 rubber-jawed viseassembly, 3 beading assembly devices with full range of rollovers.

PLIERS – Note: Unless otherwise stated, all models feature Right Hand Twist and Diagonal Nose.

6” Manual and Automatic Springs Returns

TigerWave – Unique “wave” jaw design eliminatescuts and nicks in wire

– automatic Spring Returns

9” Automatic Spring Return

12” Automatic Spring Return

9W

45W

1W393

2W393

41W

9W Tapered Nose – Manual Return9WS Tapered Nose – Automatic Return11W Diagonal (NSN 5120-01-112-5143)11WS Diagonal Nose – Automatic Return45W Reversible – Automatic Return

1W393 Automatic (NSN 5120-01-112-5031)3W5 Cushion Throat5W6 Left Hand Twist41W Reversible – Automatic Return

2W393 Automatic – Diagonal Nose4W6 Cushion throat6W4 Left Hand Twist

25W 6” TigerWave – Reversible26W 9” TigerWave – Reversible

Professional Safety Wiring Kit. Contains three different Twisters tocover almost any application. 9”Automatic, 6” Mini, and a 19” DeepReach Twister. Includes three 1/4 lb.Spools of stainless steel safety wire(0.020, .032, .040). Durable plasticstorage case.Weight: 4lbs.Length: 13-1/2” Width: 10”Height: 2-1/16”

No. 105W

108

109

BURRAWAY DEBURRING TOOLSBURRAWAY TOOLTYPE A - 1/4” SHANKAll dimensions shown in inches.For “COMPLETE TOOL” add “YA” BEFORE HOLE SIZE.For “REPLACEMENT BLADE ONLY” ADD “DA” BEFOREBLADE SIZE.

HOLE SIZE REPLACEMENTP/N (YA-) DEC. EQUIV. DIM.”A” DIM.”B” DIM.”C” BLADE P/N(DA-)YA-3/32 .093 3.37 .45 .28 DA-3/32YA-7/64 .109 3.37 .45 .28 DA-3/32YA-1/8 .125 3.37 .45 .25 DA-1/8YA-9/64 .140 3.37 .45 .25 DA-1/8YA-5/32 .156 3.37 .45 .25 DA-5/32YA-11/64 .171 3.37 .45 .25 DA-5/32YA-3/16 .187 4.12 .72 .44 DA-3/16YA-13/64 .203 4.12 .72 .44 DA-3/16

The tool deburrs automatically, requiring no judgment or secondary operation on part of the worker. It reduces deburring to a simple one-step operation. working with equalease and efficiency in deburring the back of holes which isinaccessible with conventional types of tools. One simple setscrew adjustment controls depth of cut.

TYPE B-STRAIGHT SHANKAll dimensions shown in inches. For “COMPLETE TOOL”ADD “YB-” BEFORE HOLE SIZE. ‘For “REPLACEMENTBLADE ONLY” ADD “DB-” BEFORE BLADE SIZE.

HOLE SIZE REPLACEMENTP/N (YB-) DEC. EQUIV. DIM.”A” DIM.”B” DIM.”C” BLADE P/N(DB-)YB-7/32 .218 4.50 .87 .56 DB-#1YB-15/64 .234 4.50 .87 .56 DB-#1YB-1/4 .250 4.50 .87 .56 DB-#1YB-17/64 .265 4.50 .87 .56 DB-#1YB-9/32 .281 4.50 .87 .56 DB-#1YB-19/64 .296 4.50 .96 .68 DB-#2YB-5/16 .312 4.50 .96 .68 DB-#2YB-21/64 .328 4.50 .96 .68 DB-#2YB-11/32 .343 4.50 .96 .68 DB-#2YB-23/64 .359 5 1.00 .68 DB-#3YB-3/8 .375 5 1.00 .68 DB-#3YB-25/64 .390 5 1.00 .68 DB-#3YB-13/32 .406 5 1.00 .68 DB-#3YB-27/64 .421 5.50 1.09 .72 DB-#3-1/2YB-7/16 .437 5.50 1.09 .72 DB-#3-1/2YB-29/64 .453 5.50 1.09 .72 DB-#3-1/2YB-15/32 .468 5.50 1.09 .72 DB-#3-1/2YB-31/64 .484 5.50 1.09 .72 DB-#3-1/2YB-1/2 .500 5.50 1.09 .72 DB-#3-1/2

BURRAWAY DEBURRING TOOL KITContains 5 Tools & Replacement Blades housed ina fitted case. Individual tools are available.

KIT INCLUDES THE FOLLOWING:1/8” Tool & Replacement Blade 5/32” Tool & Replacement Blade3/16” Tool & Replacement Blade 7/32” Tool & Replacement Blade

BURR-OFF TOOLSThe original “clothes-Pin” tool for mass production hole deburring. For removal of burrs from front and back of holes. Adaptable to high production, automatic and automated operations.

Each tool size will effectively deburr all hole sizes in the range as shown. The BURR-OFF® is a simple onepiece construction. All BURR-OFFs (except CP-6 thru CP-9) come equipped with a sliding tension-adjustment feature to control the amount of “edge-break”.

TOOL RANGE OF HOLE SHANK OVERALLNUMBER SIZES DIAMETER LENGTH

IN. MM IN. IN.CP-6 .093-.109 2.36-2.77 .092 4.00CP-7 .109-.125 2.77-3.17 .108 4.00CP-8 .125-.140 3.17-3.55 .124 4.00CP-9 .140-.156 3.55-3.96 .139 4.00CP-10 .156-.172 3.96-4.36 .155 4.00CP-11 .172-.187 4.36-4.74 .171 4.00CP-12 .187-.203 4.74-5.15 .186 4.00CP-13 .203-.219 5.15-5-56 .202 4.00CP-14 .219-.234 5.56-5.94 .218 4.00CP-15 .234-.250 5.94-6.35 .233 4.00CP-16 .250-.266 6.35-6.75 .249 4.00CP-17 .266-.281 6.75-7.13 .265 4.00CP-18 .281-.297 7.13-7.54 .280 4.00CP-19 .297-.313 7.54-7.95 .296 4.00CP-20 .313-.328 7.95-8.33 .312 4.00CP-21 .328-.343 8.33-8.71 .327 4.00CP-22 .343-.359 8.71-9.11 .342 4.00

TOOL RANGE OF HOLE SHANK OVERALLNUMBER SIZES DIAMETER LENGTH

IN. MM IN. IN.CP-23 .359-.375 9.11-9.52 .358 4.00CP-24 .375-.390 9.52-9.90 .374 4.43CP-25 .390-.406 9.90-10.31 .389 4.43CP-26 .406-.422 10.31-10.71 .405 4.43CP-27 .422-.437 10.71-11.09 .420 4.43CP-28 .437-.453 11.09-11.50 .436 5.50CP-29 .453-.468 11.50-11.88 .452 5.50CP-30 .468-.484 11.88-12.29 .467 5.50CP-31 .484-.500 12.29-12.70 .483 5.50CP-32 .500-.515 12.70-13.08 .499 7.00CP-33 .515-.531 13.08-13.48 .514 7.00CP-34 .531-.547 13.48-13.89 .530 7.00CP-35 .547-.563 13.89-14.30 .545 7.00CP-36 .563-.578 14.30-14.68 .562 7.50CP-37 .578-.594 14.68-15.08 .577 7.50CP-38 .594-.609 15.08-15.46 .593 7.50

FeedIn

FeedThru

FeedOut

“DA-” Replacement Blade “DB-” Replacement Blade

BURRAWAY DETAILS

TYPE ATOOL

ADAPTER ASSEMBLYARBOR ASSEMBLY

ADJUSTMENTSCREW

SPRING ASSEMBLY

SPRING

PLUNGER PIVOT PIN BLADE INTEGRAL PILOT & ARBOR

TYPE BTOOL KIT CONTENTS (CONTINUED):

1/4” Tool & Replacement Blade All Tools &Blades housed in a fitted plastic case.Complete Kit Part #70938...

DEBURRING TOOLS

110

DEBURRING SYSTEMS & KITS

111

Roto-Drive Standard Set

Includes the following:• Plastic Roto-Drive Handle• 1/8" Countersink• 1/4" Countersink

• 5/16" Countersink• 3/8" Countersink• Demo Plate• Plastic Storage Case

Includes the following:• Plastic Roto-Drive Handle• 1/8" Countersink• 3/8" Countersink• E-100 Blade

• E-200 Blade• E-300 Blade• Demo Plate• Plastic Storage Case

DESCRIPTIONPACKAGE

OFCATALOGNUMBER

Roto-Drive Standard Set 1 22500

DESCRIPTIONPACKAGE

OFCATALOGNUMBER

Roto-Drive Combination Set 1 22502

Royal Roto-Drive Combination Set

HAND INSTALLATION & EXTRACTING TOOLS

GO & NO GO GAGESS.T.I. Thread

plug gages are used to check the accuracy of the tapped hole. If the tapped hole is correct, the finished thread will also be accurate when the insert is installed. It is not necessary to gage the installed insert.

Inserts are supplied in coarse and fine threads. Type 2, Type 4 and Type 6TOOLING are used for finer pitch inserts,which are larger in the free state than thecoarse pitch inserts. They have to be “pre-wound” to a smaller diameter for installation.Type1, Type 3 and Type 5 TOOLING (thread-ed mandrel) is used for coarse pitch inserts.

EXTRACTING TOOLThis tool is used to remove

inserts. Apply thetool to the insert, striking thehead of the tool lightly turn-ing it counterclockwise,maintaining steady downward pressure.

TANG BREAK-OFF TOOLThis tool is used to remove the drivingtang of inserts after theyhave been installed to eliminate theirinterference with the end of theassembled bolt. The operation of thetool is automatic, having a springloaded punch that strikes a sharp blowagainst the tang of the installed insert.

INCH SERIESCOARSE

NOMINALTHREAD

SIZE2-563-484-405-406-328-3210-2412-241/4-205/16-183/8-167/16-141/2-139/16-125/8-113/4-107/8-91-8

1-1/8-71-1/4-71-3/8-61-1/2-6

INSTALLATIONTOOL

PART NO.IM51-02IM51-03IM288-04IM288-05IM288-06IM288-2IM288-3IM288-1IM288-4IM288-5IM288-6IM288-7IM288-8IM288-9IM288-10IM288-12IM288-14IM288-16IM288-18IM288-20IM288-22IM288-24

INSERTING TOOL

PART NO.HT551-02HT551-03 HT551-04 HT551-05 HT551-06 HT551-2 HT551-3 HT551-1 HT551-4 HT551-5 HT551-6 HT551-7 HT551-8

TANG BREAK-OFF TOOL PART NO.TB695-02TB695-02TB695-04TB695-04TB695-06TB695-2TB695-3TB695-3TB695-4TB695-5TB695-6TB695-7TB695-8

*********

EXTRACTINGTOOL

PART NO.EX227-02EX227-06EX227-06EX227-06EX227-06EX227-06EX227-6EX227-6EX227-6EX227-6EX227-6EX227-16EX227-16EX227-16EX227-16EX227-16EX227-16EX227-16EX227-24EX227-24EX227-24EX227-24

GA688-02GA688-31GA688-04GA688-05GA688-06GA688-2GA688-3GA688-1GA688-4GA688-5GA688-6GA688-7GA688-8GA688-9GA688-10GA688-12GA688-14GA688-16GA688-18GA688-20GA688-22GA688-24

GA440-02GA440-31GA440-04GA440-05GA440-06GA440-2GA440-3GA440-1GA440-4GA440-5GA440-6GA440-7GA440-8GA440-9GA440-10GA440-12GA440-14GA440-16GA440-18GA440-20GA440-22GA440-24

GO & NO GAGES(COMPLETE)

3B 2BTYPE

1155555555555555553333

TYPE

2222222222222

FINENOMINALTHREAD

SIZE3-564-486-408-3610-3212-281/4-285/16-243/8-247/16-201/2-209/16-185/8-183/4-167/8-141-141-12

1-1/8-121-1/4-121-3/8-121-1/2-12

INSTALLATIONTOOL

PART NO.

IM299-3

IM299-4IM299-5IM299-6IM299-7IM299-8IM299-9IM299-10IM299-12

INSERTING TOOL

PART NO.HT552-03HT552-04HT552-06HT552-2HT552-3HT552-1HT552-4HT552-5HT552-6HT552-7HT552-8HT35-9HT35-10HT35-12HT35-14HT35-16HT35-161HT35-18HT35-20HT35-22HT35-24

TANG BREAK-OFF TOOL PART NO.TB695-02TB695-04TB695-06TB695-2TB695-3TB695-3TB695-3TB695-4TB695-6TB695-7TB695-8

**********

EXTRACTINGTOOL

PART NO.EX227-06EX227-06EX227-06EX227-06EX227-6EX227-6EX227-6EX227-6EX227-6EX227-16EX227-16EX227-16EX227-16EX227-16EX227-16EX227-16EX227-16EX227-24EX227-24EX227-24EX227-24

GA694-03GA694-04GA694-06GA694-2GA694-3GA694-1GA694-4GA694-5GA694-6GA694-7GA694-8GA694-9GA694-10GA694-12GA694-14GA694-16GA694-161GA694-18GA694-20GA694-22GA694-24

GA441-03GA441-04GA441-06GA441-2GA441-3GA441-1GA441-4GA441-5GA441-6GA441-7GA441-8GA441-9GA441-10GA441-12GA441-14GA441-16GA441-161GA441-18GA441-20GA441-22GA441-24

GO & NO GAGES(COMPLETE)

3B 2BTYPE

6

66666664

TYPE

222222222224444444444

112

*use standard needle nose pliers toremove tangs on this size insert.

TYPE 1INSTALLATION TOOL

Threaded Mandrel(SIZES 2-56 and 3-58)

TYPE 2HAND INSERTING TOOL

(Prewinder Tool)

TYPE 3INSTALLATION TOOL(Threaded Mandrel)

TYPE 4NON-CAPTIVEPREWINDER

TYPE 5INSTALLATION TOOL(Threaded Mandrel)

TYPE 6INSTALLATION TOOL

(Threaded Mandrel with Prewinder)

TYPE THREAD REPAIR KITS

THREAD REPAIRKITS INCH SERIES

Individually-packaged kitsare available for inch coarseand fine series sizes from 4-40 to 1-1/2-12. Each kitcontains everything youneed to complete a threadrepair: drill, tap, installationtool, and a quantity ofStainless Steel Inserts.

INCH COARSE THREAD REPAIR KITS

THREAD SIZE +

LENGTH4-40 x .1685-40 x .1886-32 x .2078-32 x .246

10-24 x .28512-24 x .3241/4-20 x .375

5/16-18 x .4693/8-16 x .562

7/16-14 x .6561/2-13 x .750

9/16-12 x .8445/8-11 x .938

3/4-10 x 1.1257/8-9 x 1.3121-8 x 1.500

1-1/8-7 x 1.6881-1/4-7 x 1.8751-3/8-6 x 2.0621-1/2-6 x 2.250

KITP/N

IK401-04DIK401-05DIK401-06DIK401-2DIK401-3DIK401-1DIK401-4DIK401-5DIK401-6DIK401-7DIK401-8DIK401-9D

IK401-10DIK401-12DIK521-14DIK521-16DIK521-18DIK521-20DIK521-22DIK521-24D

INSTALLATIONTOOL P/NIM288-04IM288-05IM288-06IM288-2IM288-3IM288-1IM288-4IM288-5IM288-6IM288-7IM288-8IM288-9IM288-10IM288-12IM288-14IM288-16IM288-18IM288-20IM288-22IM288-24

TAPP/N

TP04-CPBTP05-CPBTP06-CPBTP2-CPBTP3-CPBTP1-CPBTP4-CPBTP5-CPBTP6-CPBTP7-CPBTP8-CPBTP9-CPBTP10-CPBTP12-CPBTP14-CPBTP16-CPBTP18-CPBTP20-CPBTP22-CPBTP24-CPB

PACKAGEINSERT

P/NPK185-04PK185-05PK185-06PK185-2PK185-3PK185-1PK185-4PK185-5PK185-6PK185-7PK185-8PK185-9PK185-10PK185-12PK185-14PK185-16PK185-18PK185-20PK185-22PK185-24

INSERTSPERKIT1212121212121212121212664665444

INSERTQUANTITY

1212121212121212121212666111111

DRILLSIZE#31#29#25

11/6413/6415/6417/6421/6425/6429/6417/3219/3221/3225/3229/321-1/321-5/321-9/321-13/321-17/32

TYPE55555555555555553333

113

KIT CONTENTS AND REPLACEMENT PARTS

INCH FINE THREAD REPAIR KITS

THREAD SIZE +

LENGTH6-40 x .2078-36 x .246

10-32 x .2851/4-28 x .375

5/16-24 x .4693/8-24 x .562

7/16-20 x .6561/2-20 x .750

9/16-18 x .8445/8-18 x .938

3/4-16 x 1.1257/8-14 x 1.3121-14 x 1.5001-12 x 1.500

1-1/8-12 x 1.6881-1/4-12 x 1.8751-3/8-12 x 2.0621-1/2-12 x 2.250

KITP/N

IK402-06DIK402--2DIK402-3DIK402-4DIK402-5DIK402-6DIK402-7DIK402-8DIK402-9D

IK402-10DIK402-12DIK528-14DIK528-16D

IK528-161DIK528-18DIK528-20DIK528-22DIK528-24D

INSTALLATIONTOOL P/NHT552-06HT552-2IM299-3IM299-4IM299-5IM299-6IM299-7IM299-8IM299-9IM299-10IM299-12HT35-14HT35-16HT35-161HT35-18HT35-20HT35-22HT35-24

TAPP/N

TP06-FPBTP2-FPBTP3-FPBTP4-FPBTP5-FPBTP6-FPBTP7-FPBTP8-FPBTP9-FPBTP10-FPBTP12-FPBTP14-FPBTP16-FPBTP161-FPBTP18-FPBTP20-FPBTP22-FPBTP24-FPB

PACKAGEINSERT

P/NPK191-06PK191-2PK191-3PK191-4PK191-5PK191-6PK191-7PK191-8PK191-9PK191-10PK191-12PK191-14PK191-18PK191-16PK191-18PK191-20PK191-22PK191-24

INSERTSPERKIT12121212121212126646665444

INSERTQUANTITY

121212121212121212664111111

DRILLSIZE#25#17

13/6417/6421/6425/6429/6433/6437/6441/6448/6457/641-1/641-1/641-5/321-9/321-13/321-17/32

TYPE226666666664444444


TYPE THREAD REPAIR KITS

MASTER THREADREPAIR KITS

INSTALLATION TOOLS

TYPE 5

TYPE 6INSERTS

MASTER THREAD REPAIR KITS contain the most commonly used thread sizes all in one!!!Each kit contains a S.T.I. tap, installation tool, and a pack-age of inserts for each size. (Drills sold separately).

INCH SERIES COARSEPART NO. IK934 – CONTENTS:

THREAD SIZE + LENGTH

1/4-20 x .3755/16-18 x .4693/8-16 x .562

7/16-14 x .6561/2-13 x .7505/8-11 x .938

INSTALLATIONTOOL P/NIM288-4IM288-5IM288-6IM288-7IM288-8

IM288-10

TAPP/N

TP4-CPBTP5-CPBTP6-CPBTP7-CPBTP8-CPB

TP10-CPB

PACKAGEINSERT P/N

PK185-4PK185-5PK185-6PK185-7PK185-8

PK185-10

INSERTQUANTITY

12121212126

DRILLSIZE17/6421/6425/6429/6417/3221/32

FINEPART NO. IK936 – CONTENTS:


10-32 X .2851/4-28 X .375

5/16-24 X .4693/8-24 X .562

7/16-20 X .6861/2-20 X .750

INSTALLATIONTOOL P/NIM299-3IM299-4IM299-5IM299-6IM299-7IM299-8

TAPP/N

TP3-FPBTP4-FPBTP5-FPBTP6-FPBTP7-FPBTP8-FPB

PACKAGEINSERT P/N

PK191-3PK191-4PK191-5PK191-6PK191-7PK191-8

INSERTQUANTITY

121212121212

DRILLSIZE13/6417/6421/6425/6429/6433/64

METRIC SERIESPART NO. IK937 – 150:


M5 X 0.8 X 7.5M6 X 1.0 X 9.0

M8 X 1.25 X 12.0M10 X 1.5 X 15.0

INSTALLATIONTOOL P/NIM747-5IM747-6IM747-8IM747-10

TAPP/N

TP5M-CPATP6M-CPATP8M-CPATP10M-CPA

PACKAGEINSERT P/N

PK084-5PK084-6PK084-8PK084-10

INSERTQUANTITY

12121212

DRILLSIZE13/641/4

21/6413/32

PART NO. IK937 – IK937-125:THREAD SIZE +

LENGTHM5 X 0.8 X 7.5M6 X 1.0 X 9.0

M8 X 1.25 X 12.0M10 X 1.25 X 15.0

INSTALLATIONTOOL P/NIM747-5IM747-6IM747-8

IM747-10-1

TAPP/N

TP5M-CPATP6M-CPATP8M-CPA

TP10M-MPA

PACKAGEINSERT P/N

PK084-5PK084-6PK084-8PK335-10

INSERTQUANTITY

12121212

DRILLSIZE13/641/4

21/6413/32

METRIC COARSE THREAD REPAIR KITS

THREAD SIZE +

LENGTHM3 X 0.5 X 4.5

M3.5 X 0.6 X 5.3M4 X 0.7 X 6.0M5 X 0.8 X 7.5M6 X 1.0 X 9.0

M7 X 1.0 X 10.5M8 X 1.25 X 12.0M9 X 1.25 X 13.5M10 X 1.5 X 15.0M11 X 1.5 X 16.5

M12 X 1.75 X 18.0M14 X 2 X 21.0M16 X 2 X 24.0

M18 X 2.5 X 27.0M20 X 2.5 X 30.0

KITP/N

IK403-3DIK403-3.5DIK403-4DIK403-5DIK403-6DIK403-7DIK403-8DIK403-9D

IK403-10DIK403-11DIK403-12DIK403-14DIK403-16DIK403-18DIK403-20D

INSTALLATIONTOOL P/NIM747-3

HT751-3.5IM747-4IM747-5IM747-6IM747-7IM747-8IM747-9

IM747-10IM747-11IM747-12IM747-14IM747-16IM747-18IM747-20

TAPP/N

TP3M-CPATP3.5M-CPATP4M-CPATP5M-CPATP6M-CPATP7M-CPATP8M-CPATP9M-CPA

TP10M-CPATP11M-CPATP12M-CPATP14M-CPATP16M-CPATP18M-CPATP20-CPA

PACKAGEINSERT

P/NPK084-3

PK084-3.5PK084-4PK084-5PK084-6PK084-7PK084-8PK084-9PK084-10PK084-11PK084-12PK084-14PK084-16PK084-18PK084-20

INSERTSPERKIT12121212121212121212126664

INSERTQUANTITY

121212121212121212666664

DRILLSIZE1/8#27

11/6413/64

1/49/3221/64

3/813/3229/6431/6437/6421/3247/6413/16

TYPE626665555655555


METRIC COARSE THREAD REPAIR KITS

THREAD SIZE +

LENGTHM8 X 1.0 X 12.0

M10 X 1.0 X 15.0M10 X 1.25 X 15.0M11 X 1.0 X 16.5

M11 X 1.25 X 16.5M12 X 1.25 X 18.0M12 X 1.5 X 18.0M14 X 1.5 X 21.0M16 X 1.5 X 24.0M18 X 1.5 X 27.0

KITP/N

IK404-8DIK404-10DIK405-10DIK404-11D IK405-11DIK405-12DIK406-12DIK406-14DIK406-16DIK406-18D

INSTALLATIONTOOL P/NIM835-8

IM835-10IM640-10-1IM640-11-1IM640-11IM640-12IM973-12IM973-14IM973-16IM973-18

TAPP/N

TP8M-FPATP10M-FPATP10M-MPATP11M-FPATP11M-MPATP12M-FPATP12M-MPATP14M-FPATP16M-FPATP18M-FPA

PACKAGEINSERT

P/NPK255-8PK255-10PK355-10PK255-11PK355-11PK255-12PK355-12PK355-14PK355-16PK355-18

INSERTSPERKIT12121212121212665

INSERTQUANTITY

12121212121212665

DRILLSIZE21/6413/3213/327/1629/6431/6431/649/1621/3223/32

TYPE6666666666


114

TYPE 2 TYPE 3 DRILL TAP

SWAGING MACHINES

type II beanch model manual swagging tool kit– part no. M2-k*

115

SWAGING EQUIPMENT

SWAGED CABLE TERMINALPULL TESTER KITAT 520CTK........................

AT 520J SWAGER

This light-weight portable unit is designed to precision swage cable terminals…even whenused by operators with no previous experience. It can be used as a bench unit when mounted on the shock absorbing base or taken directly to the scene of operation.

The AT 520CTK Portable Cable Pull Tester Kit is used in conjunction with the AT 520D and AT 520J Cable Swagers. It has been designed as a portable unit to enable Field Service Groups, Aircraft Manufacturers and Repair depots to test swaged terminals

Dies are for standard MS Sleeve Type and Ball End Terminals. Cut-off trim dies are manufactured in sizes to cut cable up to 1/4” in diameter without fraying or crushing wire strands. The kit is furnished with swager and all dies (1/16-3/16).

COMPLETE KIT CONSISTS OF THE FOLLOWING:

AT 520CTPULL TESTERAT 520 CT Swaged Terminal Pull Tester

Complete with Handle and Jaw Holder

AT 520 CTB Carrying CaseAT 520 CTD-1 BlockAT 520 CTD-2 Jaws for 1/16” dia. cableAT 520 CTD-3 “ “ 3/32” “ “AT 520 CTD-4 “ “ 1/8 ” “ “AT 520 CTD-5 “ “ 5/32” “ “AT 520 CTD-6 “ “ 3/16” “ “AT 520 CTD-7 “ “ 7/32” “ “AT 520 CTD-8 “ “ 1/4 ” “ “AT 520 CTF-5 Adapter for 5/32 AN 667 TerminalAT 520 CTF-6 Adapter for 3/16 AN 667 TerminalAT 520 CTF-7 Adapter for 7/32 AN 667 TerminalAT 520 CTF-8 Adapter for 1/4 AN 667 TerminalAT 520 CTS-2 Adapter for 1/16 AN 663 & AN 664 TerminalsAT 520 CTS-3 Adapter for 3/32 AN 663 & AN 664 TerminalsAT 520 CTS-4 Adapter for 1/8 AN 663 & AN 664 TerminalsAT 520 CTS-5 Adapter for 5/32 AN 663 & AN 664 TerminalsAT 520 CTS-6 Adapter for 3/16 AN 663 & AN 664 Terminals

AT 520 CTT-2 Adapter for 1/16 AN 666 & AN 669 Terminals (R.H. TA’D)AT 520 CTT-3 Adapter for 3/32 AN 666 & AN 669 Terminals (R.H. TA’D)AT 520 CTT-4 Adapter for 1/8 AN 666 & AN 669 Terminals (R.H. TA’D)AT 520 CTT-4 Adapter for 5/32 AN 666 & AN 669 Terminals (R.H. TA’D)AT 520 CTT-6 Adapter for 3/16 AN 666 & AN 669 Terminals (R.H. TA’D)AT 520 CTT-7 Adapter for 7/32 AN 666 & AN 669 Terminals (R.H. TA’D)AT 520 CTT-20 Adapter for 1/16 AN 666 & AN 669 Terminals (L.H. TA’D)AT 520 CTT-30 Adapter for 3/32 AN 666 & AN 669 Terminals (L.H. TA’D)AT 520 CTT-40 Adapter for 1/8 & 5/32 ” ” ” ” ” ” ”AT 520 CTT-60 Adapter for 3/16 AN 666 & AN 669 Terminals (L.H. TA’D)AT 520 CTT-70 Adapter for 7/32 & 1/4 ” ” ” ” ” ” ”AT 520 CTP-1 Pin 3/16 Dia. )AT 520 CTP-2 Pin 1/4 Dia. )AT 520 CTP-3 Pin 5/16 Dia. )AT 520 CTP-4 Pin 3/8 Dia. )

For AN 667 & AN 668

Terminals

PORTABLE CABLE SWAGER KITAT 520JK........................

116

JOBOLT – VISU-LOK TOOLS

117

118

HI-LOK / HI-SHEAR AIR DRIVERS


119



120



121



HI-LOK/HI-LITE TYPE TOOLS

122

Roller Ratchet®Part Number

RR40SPRR40S-SPRR80SPRR130SPRR250SPRR400SP

RR40A21SPRR40A21S-SPRR40A25SP

RR40A25S-SPRR40A28SP




RR40A37S-SPRR130A25 RR130A31 RR130A34 RR130A37 RR130A43 RR25OA50 RR2E40SP

RR2E40S-SPRR2E13O RR2E250 RR2E400

Square Driveor Socket Hex

1/4”1/4”1/4”1/4”3/8”3/8”7/32”7/32”1/4”1/4”9/32”9/32”5/16”5/16’11/32’11/32”3/8”3/8’1/4”5/16”11/32”3/8”7/16”1/2”1/4”1/4”1/4”3/8”3/8”

Max Torquelb-in150150200250400600150150150150150150150 150 150 150 150 150 250 250 250 250 250 400 150 150 250 400 600

OAL6”

3.5”6-1/4”

7”7-3/4”8-1/2”

6”3.5”6”

3.5”6”

3.5”6”

3.5”6”

3.5”6”

3.5”7”7”7”7”7”

7-3/4”7”

4.5”7”

7-3/4”8-1/2”

HEADWIDTH

5/8”5/8”.60”7/8”1”

1.3”5/8”5/8”5/8”5/8”5/8”5/8”5/8”5/8”5/8”5/8”5/8”5/8”7/8”7/8”7/8”7/8”7/8”1”

5/8”5/8”7/8”1”

1.3”

HEADHEIGHT

.5”

.5”1.0”.6”.62”.75”1/2”1/2”1/2”1/2”1/2”1/2”1/2”1/2”1/2”1/2”1/2”1/2”.6”.6”.6”.6”.6”

5/8”1/2”1/2”.6”

5/8”.75”

123

1. RR40S-SP Standard, "Short" Reversible Roller Ratchet® with through-hole. Has 1/4" male square drive with compression ringfor socket retention. (150 lb-in rating)

3. RR40A (size) S-SP This series Roller Ratchet® is very low profilewith integral (one-piece spindle) socket. The sockets are shallowfor Hi-Lok® installation in low height spaces. (150 lb-in rating)Available individually or in sets of 6.

4. RR40SP Standard "Long" Reversible Roller Ratchet® withthroughhole. Has 1/4" male square drive with compression ringfor socket retention. (150 lb-in rating)

5. RR2E40SP Double-Ended Reversible version of "Long" RollerRatchet®. Eliminates need to reverse the spindle to go frominstallation to removal. 1/4" square drive with through-hole andcompression ring for socket retention. (150 lb-in rating)

6. RR2E40S-SP Double-Ended Reversible version of "Short" RollerRatchet®. Eliminates need to reverse the spindle to go frominstallation to removal. 1/4" square drive with through-hole andcompression ring for socket retention. (150 lb-in rating)

14. RR80SP Taller than the RR40SP tool, but more torque. Has 1/4"male square drive with compression ring for socket retention.(150 lb-in rating)

15. RR130A (size) SP series wrenches have Integral Sockets, a larger diameter clutch, and low height, but provide additionaltorque capability - 250 lb-in.

16. RR130SP Larger clutch provides 250 lb-in rating with 1/4"square drive.

18. RR250SP 3/8" Square-Drive Roller Ratchet® with through-hole,and 400 lb-in rating.

19. RR400SP 3/8" Square Drive Roller Ratchet® with through-hole,and 600 lb-in rating. This is our largest Roller Ratchet®

Roller Ratchet®

ROLLER RATCHET® For Hi-Loks® and Limited Access

1.

4.

14.

5.

15.

16. 18.

19.

3. 6.

8. 9. 10.

HI-LOK/HI-LITE GAGES

Hi-Lok® Removal Pliers offer aquick and inexpensive alternative forremoving any frangible hex collar such asHi-Lok, Hi-Lite, Hi-Tigue, Veri-Lite and C-Lok fasteners. The hardened steel jawsare specially designed to maximize thegripping surface around the collar. Thisallows the ZHP-100 pliers to grip5/32”, 3/16”, 1/4” and 5/16” fastener sizes.

For non-Interference fit holes, the ZHP-100removal pliers should be used inconjunction with a hex key.

The original and best instrument for measuring both hole depth andfastener grip. The scale is spring temper stainless steel and 3/4” x 6-1/4” in size.The finish is satin with red and black lettering.

TESTING EQUIPMENT

ZHP-100

HI-LOK® PLIERS

PROPELLER PROTRACTOR

Universal propeller protractor is a deviceused to measure the propeller blade angleat a specific blade station, also to determine ifthe propeller is properly adjusted. The bladeangle is referenced from the propeller plane ofrotation, which is ninety degrees to the crankshaft centerline. The frame of the protractor ismade of aluminum and has three sides whichare ninety degrees to each other. Also includes aswing out level located in lower corner to assistin deter-mining proper vertical line.#2113.......................

Instant measurements of level, angle and tilt, with digital display.A thousand times easier to use over the old method. Featuresinclude: Sizes 5-1/2”x3”. Alternate reference feature for quickand accurate measurement of deviations from reference sur-face.Hold button freezes the display angle. V grooves insureaccurate reading on curved surfaces: 9V battery.#5490 ................................

DigitalPropellerProtractor

Small lightweight precision instrument.Accuracy is not affected by extreme heat orcold. Gauge pointer has lock feature to allowholding of reading. Chart converting readingto pounds of tension enclosed. Range inpounds 15-150. Cable sizes: 1/16”, 3/32”,5/32”, 3/16”, 7/32”, 1/4”, Wt. 12 oz.#T5 ..............................

GAGE SET DESCRIPTION PART NUMBER

Hi-Lite (Inches)Includes gages for5/32”, 3/16”, 1/4”, 5/16”and 3/8” pin diameters

Hi-Lite (Metric)Includes gages for4, 5, 6, 8, 10 & 12mmpin diameters

Hi-Lok/Hi-Tigue (Metric)Includes gages for4, 5, 6, 8, 10 & 12mmpin diameters

2-1522HST

(Stainless Steelwith red copy)

2-1522HSTM

(Stainless Steelwith green copy)

2-1522HLM

(Stainless Steelwith purple copy)

CONTROL CABLE TENSIOMETER

#C 8: 0-200 lbs.1/16 - 1/4 cable . . . .#C 9: 150-450 lbs.1/8 - 1/4 cable . . . . .

#BT 33-75DFor use on cables 1/16”, 3/32”, 1/8”diameter. Tension range 15-70 lbs.

#BT 33-75-GFor use on cables 5/32”, 3/16”, 1/8”diameter. Tension range 50-350 lbs.

#BT 33-75-HFor use on 1/4” cable.Tension range 50-350 lbs.

AIRCRAFT CABLE GAUGES

2-1522Protrusion

GagesStainless Steel

with Black Copy

2-612GripScale

Scale for measuring depth of hole. Graduated in 1/16”increments to 3”.

Scale for measuring griplength of fasteners graduatedin 1/16” increments to 3”.

The 2-1522 Hi-Lok Protrusion Gages offer a convenientmethod to check Hi-Lok pin protrusion limits after the Hi-Lokpin has been inserted in the hole and before or after collarinstallation. Individual gages accommodate Hi-Lok pin diametersizes 5/32, 3/16, 1/4, 5/16, and 3/8. Gages are made of .012stainless steel and are assembled as a set on a key chain.

SCALE FOR MEASURING GRIP LENGTH OFFASTENERS. GRADUATED IN MILLIMETER INCREMENTS TO 7-1/2 CENTIMETERS.

SCALE FOR MEASURING DEPTH OF HOLE. GRADUATED IN MILLIMETERINCREMENTS TO 7-1/2 CENTIMETERS.

124

*

The Notched jaws are designed formaximum gripping from the top orbottom of the offset pliers head.

*

MISCELLANEOUS

Rear-exhausted tool makes short work of removing dried-out gasketmaterial. Won’t damage underlying surface. Lever throttle providesprecise speed control. Straight-handle design helps make this tooleasy to hold and use - great for tight spaces under hood. Features a lightweight aluminum housing and durable steel blade.

GASKET SCRAPERFP703.............

Siphon Spray Gun

#702 ................................• High flow Applications• Designed for Spraying Solvents,

Soaps, etc.• 8’ Clear Plastic Suction Tubing• 6” Nose Extension • Pistol Grip Style• 15 oz.

One–Quart Professional Spray Gun and CupFEATURES• Completely dependable• Built to perform year after year at

top efficiency• Large air passages• Provides constantly uniform

finishes

SPECIFICATIONS

• Air Inlet 1/4” NPS

• Air Cons 9-11.5 CFM

• Fluid Inlet 3/8” NPS

• Air Pressure 50 PSI

#AS7A

AIR FILEFP705Reciprocating air file makes filing in confinedspaces easy. Includes flat, round, triangular and bastard cut files. 1/4” strokelength makes quick work of metal removal.

AIR FILE ACCESSORIES(Not Shown)FP 5679 3 pk. mill cutFP 5680 3 pk. round single cutFP 5681 3 pk. triangular single cutFP 5682 3 pk. flat bastard cutFP 5683 Set of 4 assorted files

MASTERHEAT GUNHG501AAdjustable Bench Top BaseHeat Range: 500ºF-750ºF 14 AMPS. 120V Available 220V...

HG751B Heat Range: 750ºF-1000ºF14.5 Amps, 120V........

ARO MARKING PEN

• Comfortable, easy-to-use tool for engraving products or tooling for identification.

• Ideal for marking welds for identification.• Can be used to scribe a line on glass for cutting.• Cutting of fine, medium, or coarse marking point.No Cost Options• 39862-1 Fine Point • 39862-3 Coarse PointTo order, specify Model 8315 w/option number

MODEL

8315

THROTTLETYPE

Twist

STANDARDPOINT

Medium

LENGTHin.

6.4

AIR SCRIBE

CP-9361 Air Scribe

CP-9361-1 Air Scribe kit

Bold Type indicates popular stock models

CatalogNumber Description

Overalllength

in. (mm)

5

(127)

5

(14)

Net Weight

oz. (kg)

CP-9361-1 AIR SCRIBE KITINCLUDES 4 CHISELS AND 2 STYLI:

STANDARD EQUIPMENT:(1) Stylus, hose and strainer

Applications: Writes as easily as a ballpointpen on a variety of materials such as steel andother metals, plastic, glass, and wood. Can alsobe converted to a light scaler or hammer fordeburring, trimming, peening or driving pins.

15Z-710 Air Marking Pen15Z-720 Air Marking Pen Kit Dotco®

Simplified in-line piston motor with only two moving parts for longer trouble-free operation.20,000 strokes per minute variable speed.Suitable for making a variety of materials from aluminum to titanium. Air consumption less than 1 CFM.Integral air strainer prevents air line contamination.Sliding sleeve throttle for positive power control: accurate speed selection.Lightweight: weighs only 4 ounces for operator comfort.Compact design with contoured nose piece for better maneuverabilityand easier handling.Easily replaceable, long lasting carbide tipped stylus.15Z-720 Air Marking Pen Kit includes: 15Z-710 Air Marking Pen; 5 foot 3/16” I.D. Hose Assembly with 1/8” and 1/4” NPT fittings: Two (2) 1/2” Wrenches; Carrying Case.

125

ABRASIVE BLASTING EQUIPMENT

The Model 19 is a sturdy welded steel cabinet. It is aself- containedunit operating on115V alternatingcurrent and connects intoyour present airsupply. The Model19 will accept and recirculate mostpopular blastmedia. The unit isequipped with aninternal blasting

gun that controls air flow. (Carbide nozzles are available).

F.O.B. MICH.Specifications: Overall height 24”, Exterior width 19”,

Exterior depth 15”, Top opening 171⁄2” x 13”

MODELOverall HeightExterior Width (Front)Exterior Depth (Side)Door HeightDoor WidthWindow SizeInterior Lighting*Exhaust Fan – RPMElectricityFilter Bags**Shipping WeightPrice

MODEL 203060”30”20”11”16”

71⁄2”x171⁄2”1 – 200W1 @ 3010

115V1

145#

MODEL 3860”38”24”11”20”

71⁄2”x171⁄2”1 – 200W2 @ 3010

115V2

165#

MODEL 4460”44”30”

16”B 12”F27”

71⁄2”x171⁄2”2 – 200W2 @ 3010

115V2

220#

MODEL 5076”44”44”39”32”

71⁄2”x171⁄2”1 – 200W3 @ 3010

115V3

575#

*Extended Service Bulbs ** Bag Size: 21” x 35”F.O.B. MICHIGANALL PRICES INCLUDE DUST COLLECTION SYSTEM

AIR SPOT BLASTERwith four nozzles

#R201...........................For doing small touch-ups orcleaning around rivet holes, etc.Blasting material is recycled inthe closed system and is usedmany times over, no ventilationrequired. Leaves a perfect etchedsurface for filing, painting, etc.

Dee-Blast Abrasive Blast Systems are dry cleaning, finishing and polishing systems for use with most common abrasives, including glass beads, aluminum oxide, garnet, walnut shells,etc. An exterior on-off switch controls the exhaust fan and lighting. Cabinet is sealed at windows,door openings, and at bottom of hopper where media is discharged. Internal gun system isdesigned to produce various finishes, fine to coarse. Cabinet operates under negative pressure.Blast system is venturi type. Through the design of the gun system, the air picks up the mediathrough a tube inserted into the media and blasts it through the nozzle.

MODEL 130 PORTABLE SAND BLASTING SYSTEMHopper 201⁄2”x91⁄2” dia. drum holds up to 65 lbs. of abrasive. Comes completewith 10 ft. hose, blast gun, and fulllength face shield.

F.O.B. MICH.

126

Bench Model 19 CYCLO AERO POLISHERDeveloped for the aircraft industry, the Cyclo Wonder Tool is governmentapproved for the high exactingdemands of cleaning and polishing. It is used by most major airlines andaircraft manufacturers and will polishany surface–flat, curved, concave orconvex without gouging, marring orburning, as a rotary polisher may do.Leaves no swirl marks, gives a beautifully polished finish. Even abeginner can do a professional job quickly, easily, safely. Also usedas a swirl free sander, scrubber, stripper and cleaner.

FLOOR MODELS

ABRASIVSES 50lb. bags

GLASS BEADS(Coarse, medium or fine)

ALUMINUM OXIDE SILICA SAND

No. 5 (Electric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .No. 5C (Electric) 230V/50HZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . .No. 11A(Air). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . #2002 Polishing Bonnets Wool Pile. . . . . . . . . . . . . . . . . . . . . . . #2005 Applying Polish. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .#2006 Deoxidizing & Compounding (Remove Paint). . . . . . . . .

SHEET METAL MACHINERY AND SHEARS

Sheet Metal Brake Slip Rolls16 GaugeMetalShears

Bends up to 22-gauge metals. Two models to choose from,both all-steel welded construction with bronze bushings,plastic hand grips.

SPECIFICATIONSModel ModelS48 U48

Capacity 22-gauge Mild SteelMaximum Bending Length 48-1/2” 48-1/4”Flange Full Length 3/8” 3/8”Maximum Lift of Beam 7/8” 7/8”Minimum Reverse Bend 5/16” 5/16”Finger Width ___ 2”, 3”, 4”Maximum Depth of Box 0-1/8” 0-1/8”Shipping Weight 210# 280#

F.O.B. FACTORY

Heavy-duty 16 GaugeBox and Pan BrakeWeight: 500 lbs.Bending Length: 48”Finger Width: 2”, 3”, 4”Model “U4816............Floor Stand NS48..............

F.O.B. Factory

Strong on features, these shears offer precisionshearing at its best. Simple to operate, ideal forshearing mild steel through 16 gauge as well as plas-tic, lead, zinc, aluminum, brass and copper. Highly accurate cutsinsured by use of a double locking 25-1/2" back gauge.Protractor gauges, graduated side gauges, and front squaring armsare standard.

A rugged frame, tool steel blades, quality workmanship, and out-standing design techniques combine to provide a useful tool with along dependable life.

Safety features include positive pedal stops, "full vision" fingerguard and front arm extensions.

SPECIFICATIONSModel 36” Model 52”16 Gauge 16 Gauge

Capacity Mild Steel Mild SteelMaximum Cutting Length 37-5/8” 52-1/2”Back Gauge Range 25-1/2” 25-1/2”Approximate Shipping Weight 700# 1100#Overall Length 44-1/2” 59-1/2”Overall Width Incl. Gauges 73-1/2” 73-1/2”Width Less Gauges 27” 36”Overall Height 41” 41”

F.O.B. Factory

TENNSMITH slip rolls are ideal for the tool room, sheet metalshops, and school training programs. Simple to adjust andoperate, they are manufactured with many exceptional fea-tures including rolls, accurate circle settings and wire grooves.

SPECIFICATIONSModel Model Model SR 24” SR 36” SR 48”

Slip Roll 24” 36” 48”Maximum Forming Width 24” 36” 48”Material Capacity 20 Gauge 22 Gauge 16 GaugeDiameter of Rolls 2” 2” 3”Minimum Radius 1” 1”Net Weight 140# 183# 775#

Floor StandSR 24FS SR 36FS SR 48FS

Stand Weight 94# 120# 270#

F.O.B. Factory

127

SHEET METAL MACHINERY

128

Model 1447-6DT foot operated

SHEET METAL SHRINKING AND STRETCHING MACHINE

Originally developed for use in the aircraft industry on aluminum parts, the 1447-6DT is now widely used by theentire metal working industry because of its ability to:• Remove wrinkles and fit sections normally formed in

presses or drop hammers.• Form rolled, extruded and formed angles and tees.• Produce double curvatures from flat sheets.The machine performs efficiently on most metals.The Model 1447-6DT combines shrinking and stretching capabilities into one unit and provides the following advantages:• Eliminates time consuming hand de-wrinkling and

hammering operations.• Eliminates expensive form blocks and special anvils.• Increases work output and reduces operator fatigue.• Eliminates use of special dies or presses in forming various

shapes and contours on angles, tees and other sections.• Cold-worked materials results in higher material strengths.• F.O.B. Factory

SPECIFICATIONSModel 1447-6DTCapacity maximum metal

Thickness of 70,000 PSI tensile . . . . . . . . . . . .5/64 in.Depth of throat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 in.Distance from floor to working surface jaws . . 43-1/4 in.Stroke of ram . . . . . . . . . . . . . . . . . . . . . . . . . . . .1/4 in.Overall Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 in.Overall Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 in.Overall Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 in.Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .330 lbs.Shipping Weight, Crated . . . . . . . . . . . . . . . . . . .430 lbs.Shipping Weight, export boxed . . . . . . . . . . . . . . .510 lbs.Box Dimensions . . . . . . . . . . . . . . . . .20” W x 55” x 29”L

BEVERLYThroatless ShearBeverly Throatless Shears are ideal all-purpose metal cuttingtools because they permit any desired cut in heavy gauges, yethandle lighter metals without distortion. Unique shoulder designallows work to be turned in any position during the cut. Gearedrack and pinion makes heavy metal cutting easy. Upper andlower blades are positioned to provide a clean, knurl-free cut,regardless of material, All models equipped with high carbon,high chrome blades. F.O.B. Chicago, IL

Weight 18 lbs. 35 lbs. 58 lbs.Height overallHeight less handle 14” 15” 15”Handle 18” 24” 30”Width 7” 9” 9”Depth 9” 10” 14”Length Blades 4-1/4” 4-3/8” 5-5/8”

Capacities 14 Gauge mild: 18 gauge

stainless

10 Gauge mild: 14 gauge

stainless

3/4” Gauge mild: 10 gauge

stainless

B-1 B-2 B-3

ERCO

HANDFORMER MODEL HF80CH

SHEET METAL SHRINKER AND STRETCHER

CONVERSION ASSEMBLY #908-SH SHRINKER ......................... #908-ST STRETCHER.............................

#3712 METAL SHRINKER PLUS STRETCHER CONVERSIONS ASSEMBLY………………

No. 371 No. 372

Portable, Manually operated machine. (includes one set of standard shrinking and stretching jaws)HF80 CH-SHRINKER/STRETCHER . . . . . . . . . . . . . . . . . . . . .HFL70 SP NO-MAR JAWS . . . . . . . . . . . . . . . . . . . . . . . . . .OTHER TOOLING ADDITIONAL . . . . . . . . . . . . . . . . . . . . . . .(Punching, Notching, Pressing Joining) . . . . . . . . . . . . . . . .

TECHNICAL DATA: 69 LBS Stainless .059”Light Metal .79”

The aircraft repair and modification man, the sheet metal shop, the sign man and the specialist… just can’t afford to be without theseefficient tools – small yet powerful. They work and form average metals – including 16 gauge. They shrink and stretch angles downto a 2” to 3” radius. They handle angles as wide as 1” and 6” to 8” deep. A 45 to 1 leverage provides fast powerful action.

SHEET METAL PUNCHES – ROTARY MACHINE

129

Roll Chart for Rotary Machine Model R-22

Name“A”1/8”

“C”

“E”

“F”3/4”

PartNumber2210022101221062210722110221112211322114

GaugeRequired

22103

22103

22112

22103

Function

Turning

Burning

Crimping

OgeeBeading

RollDiagram

#5JRMB Mounting Base

#XXMB

PORTABLE “LITENING”

130

TRIPLE-ACTION “LIGHTNING” HOLE PUNCHES

CHISEL AND PUNCH KITS

131

FILES – USA MFG FROM THE FINEST TOOL STEEL

132

Number 993500

AIRLINE ACCESSORIES

1/4” ARO TYPE#210 COUPLER (#100)

#2608 MALE CONNECTOR (#200)

#2609 FEMALE CONNECTOR (#300)

1/4” FOSTER TYPECOUPLER (#184)

MALE CONNECTOR #1804

FEMALE CONNECTOR #1805

1/4” LINCOLN TYPECOUPLER #1100

MALE CONNECTOR #1109

FEMALE CONNECTOR #1110

#802 1/4” SPLICER#804 3/8” SPLICER#805 1/2” SPLICER

#922 1/4” HOSE INSERT#923 3/8” HOSE INSERT#928 1/2” HOSE INSERT

#903 1/4” HOSE INSERT#906 3/8” HOSE INSERT#909 1/2” HOSE X3/8 NPT

AIR HOSE WITH 1/4” MALE FITTINGS

#3825 . . . 3/8 x 25’#3850 . . . 3/8 x 50’#1425 . . . 1/4 x 25’#1450 . . . 1/4 x 50’

NEOPRENE AIR HOSE (200–250 P.S.I.)

#43 1/4 ID 5/8 OD PRICE/FT.#64 3/8 ID 3/4 OD PRICE/FT.#84 1/2 ID 7/8 OD PRICE/FT.

NYLON COIL HOSE

N14-12 12’N14-25 25’

EFFICIENT WET OR DRY PICKUP, ALUMINUM BODY,LIGHTWEIGHT, COMES COMPLETE WITH 5” NOZZLE, ROUND BRUSH AND CREVICE TOOL20” Extension Tube #A2012#A1624 Replacement Bag

THE ORIGINAL AND ONLY“LITTLE WINDY” AIRVAC ...

POWERFUL, AIR-OPERATEDVACUUM CLEANER

MODEL A 1625

SAFETY BLOW GUNS

#600S

MINI AIR VACUUM275 – PLASTIC BODYMM1120-F18 – Aluminum Body

• Venturi Type Design• Use in Confined Areas• Pick Up Ferrous & Non–Ferrous

Chips, Bolts & Rivets• 18” Clear Flex Tube• 7 oz.#275 – 1910 Replacement Bag

COMBINATION FRL’S(Filter, Regulator, Lubricator & Gauge)

C628-2 1/4”C628-3 3/8”C628-4 1/2”

AIR TOOL OIL

133FP5830..........

1/4” In-line oiler#5800 (qt)....................#ATL128 (Gallon)..........

1/4” 1/4”

134

COMPRESSED AIR POWERED VACUUMS

SOLD IN PAKS OF 10 PER SIZEPAK OF 50 ASSORTED SIZES

135

BOELUBE® MACHINING LUBRICANTS

PAINT CUTTERS

136

Boelube® is a registered trademark of The Boeing Company.These products represent a family of proprietary lubricantsdeveloped through Boeing manufacturing operations andlubricant experience.

Boelube is non-corrosive, non-flammable, chemically stableand free of halogens, heavy metals, sulfur, phosphorus, silicone, petroleum or paraffin wax.

The application of minute amounts of Boelube, which is consumed in the metalworking process, will greatly improvetool life, surface finish and hole quality.

Boelube’s high strength polar lubricating film on the toolreduces friction, thus minimizing heat generation and subsequently the need to remove heat.

Boelube provides superior lubricity when machining materials such as aluminum, titanium and inconel where high quality finish and increases of 200% or more in tool life observed.

Boelube is recommended for use on titanium, inconel, aluminum, stainless steel, graphite, composites, honeycomb, kevlar, and wood. Boelube can also be used with ferrous and nonferrous metals.

Boelube Solids70200 White / 70201 Pink

PRODUCTCODE SIZE QUANTITY

70200-00 14.5 Oz. Cartridge 12 per Box / 24 per Case

70200-13 1.6 Oz. Push Tube 100 per Box / 288 per Case

70200-14 4 Oz. Block 25 per Box / 150 per Case

70200-40 3.5 Oz. Push Tube 32 per Box / 192 per Case

Boelube Pastes70302 Blue (Soft) / 70305 Pink (Hard) / 70307 Blue (Medium)

70307-L 4 Oz. Jar 24 per Box / 150 per case

70307-11 5 Lb. Tub 5 per Case

70307-12 12 Oz. Jar 12 per Box / 36 per Case

Boelube Liquids70104 Red (100A)

70104-04 1 Gal. Container

70104-05 5 Gal. Pail

70104-07 15 Gal. Drum

Remove Screws without Flaking or Chipping paint!Paint Cutters feature a spring-loaded pilot that centers the cutter over a screw or rivet head. The cutter scribes a perfect circle in the paint, allowing the screw or rivet to be removed withminimal flaking or blistering of the paint surrounding the head. This greatly reduces the need for, and cost of, “touch-up” later.

Helps maintain a good cosmetic appearance after the job is done and reduces the chance for wind and moisture to do further damage to costly finishes. Available with 1/4-28 threaded base for use in Micro-stop cages. Color coded for easy size selection.

PC900-4 FOR#4 (3/32”) SCREW OR RIVET HEADS SilverPC900-6 FOR#6 (1/8”) SCREW OR RIVET HEADS CopperPC900-8 FOR#8 (5/32”) SCREW OR RIVET HEADS BlackPC900-10 FOR#10 (3/16”) SCREW OR RIVET HEADS BrassPC900-1/4 FOR 1/4” SCREW OR RIVET HEADS CopperPC900K SET OF ALL 5 PAINT CUTTERS

PART NO. DESCRIPTION COLORCODE

A BOEING DEVELOPED LUBRICANT

®

Aerospace and Sheetmetal Assembly Tooling Specialists

Cherry Tooling Clecos and Temporary Fasteners

Huck Tooling Countersink Cages

All Fast Blind Rivet Tooling Countersink Cutters /Counterbores

RIVET Squeezers and Equipment Deburring tools

RIVET SNAPS Screw Drivers and Bits

Rivet Shavers Sealant Guns

Rivet Removal tools Grip Gauges

Alcoa Hi Lok Tooling Pneumatic Drills

Hi Lok Tooling Angle Drills (Pork Chop)

Eddie Bolt Tools Atlas Copco drills

Hi Torque Tooling Rivnut tooling

JIFFY Tooling Hand Tools

Dotco Tooling

Composilok and Visulok Tooling Drill Bits NAS Spec

K Fast Tooling Drill Bits (Threaded)

NutPlate Spacematic drill Motors Drill Bushes

NutPlate drill Jigs Drill Collets

FTI Cold working fasteners and tooling Drill Stops

Helicoil Tooling Drills (Step) and Reamers

Lightning hole punches

Hole Saws and Spotters

Spare Parts

For more information contact us at our webpagehttp://www.appliedfastenersandtooling.com

Applied Fasteners and Tooling Pty Ltd

2607/100 Harbour Esplanade

Docklands Victoria 3008 Australia

Colin Campbell M. +61 0 498 610 566

P +61 3 99398979 F. +61 3 99398979

E. [email protected]

Date post:	06-Apr-2016
Category:	Documents
Upload:	aft-applied-fasteners-and-tooling
View:	322 times
Download:	5 times

AFT OnlineTooling Catalogue

Documents