Communicating Advanced Geophysical Classification to Stakeholders
Herb Nelson Program Manager for Munitions Response
SERDP amp ESTCP 571-372-6400
herbnelsonnrlnavymil
Outline
Before the first engagement with stakeholders
At the first planning meeting
During the course of the project
At the conclusion of the field work
M2S2 Webinar - Communicating Classification to Stakeholders 2
Before You Meet with Stakeholders
Develop a basic understanding of the technology you donrsquot have to be able to solve the equations that describe
the process
EMI data rarr intrinsic parameters rarr classification decision
Make sure classification is appropriate to your site this stuff is great and works most places but not everywhere
Make sure you have a qualified contractor
M2S2 Webinar - Communicating Classification to Stakeholders 3
Training Resources
USACE Training
ITRC ldquoTech Regrdquo Guidance Document amp Internet-based Training
ESTCP Training Resources
M2S2 Webinar - Communicating Classification to Stakeholders 4
At the First Planning Meeting
There is a big change here but it may not be what you think wersquove always left metal in the ground
missed detections due to obstructions anomalies below threshold
we just didnrsquot know much about that metal
Using classification we know a lot about the items we leave in the ground and we have put quality systems in place to prove it
M2S2 Webinar - Communicating Classification to Stakeholders 5
At the First Planning Meeting
Donrsquot exaggerate the capabilities of classification itrsquos a really cool technology
there really are no silver bullets
Seek buy-in on the remedial action objectives defined and quantitative RAOs make classification much easier
should have been spelled out in the DD or ROD
M2S2 Webinar - Communicating Classification to Stakeholders 6
At the First Planning Meeting
Be ready with a thoughtfully-developed QAPP
This is the cornerstone of the QCQA process and should enable all team members to have confidence in the project results
M2S2 Webinar - Communicating Classification to Stakeholders 7
During the Course of the Project
Enforce the QC reporting schedule specified in the QAPP and make sure the QA Geophysicist stays up to date
Stakeholder confidence is increased by
early identification of QC issues careful and complete root cause analyses
prompt implementation of any required corrective actions
M2S2 Webinar - Communicating Classification to Stakeholders 8
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Outline
Before the first engagement with stakeholders
At the first planning meeting
During the course of the project
At the conclusion of the field work
M2S2 Webinar - Communicating Classification to Stakeholders 2
Before You Meet with Stakeholders
Develop a basic understanding of the technology you donrsquot have to be able to solve the equations that describe
the process
EMI data rarr intrinsic parameters rarr classification decision
Make sure classification is appropriate to your site this stuff is great and works most places but not everywhere
Make sure you have a qualified contractor
M2S2 Webinar - Communicating Classification to Stakeholders 3
Training Resources
USACE Training
ITRC ldquoTech Regrdquo Guidance Document amp Internet-based Training
ESTCP Training Resources
M2S2 Webinar - Communicating Classification to Stakeholders 4
At the First Planning Meeting
There is a big change here but it may not be what you think wersquove always left metal in the ground
missed detections due to obstructions anomalies below threshold
we just didnrsquot know much about that metal
Using classification we know a lot about the items we leave in the ground and we have put quality systems in place to prove it
M2S2 Webinar - Communicating Classification to Stakeholders 5
At the First Planning Meeting
Donrsquot exaggerate the capabilities of classification itrsquos a really cool technology
there really are no silver bullets
Seek buy-in on the remedial action objectives defined and quantitative RAOs make classification much easier
should have been spelled out in the DD or ROD
M2S2 Webinar - Communicating Classification to Stakeholders 6
At the First Planning Meeting
Be ready with a thoughtfully-developed QAPP
This is the cornerstone of the QCQA process and should enable all team members to have confidence in the project results
M2S2 Webinar - Communicating Classification to Stakeholders 7
During the Course of the Project
Enforce the QC reporting schedule specified in the QAPP and make sure the QA Geophysicist stays up to date
Stakeholder confidence is increased by
early identification of QC issues careful and complete root cause analyses
prompt implementation of any required corrective actions
M2S2 Webinar - Communicating Classification to Stakeholders 8
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Before You Meet with Stakeholders
Develop a basic understanding of the technology you donrsquot have to be able to solve the equations that describe
the process
EMI data rarr intrinsic parameters rarr classification decision
Make sure classification is appropriate to your site this stuff is great and works most places but not everywhere
Make sure you have a qualified contractor
M2S2 Webinar - Communicating Classification to Stakeholders 3
Training Resources
USACE Training
ITRC ldquoTech Regrdquo Guidance Document amp Internet-based Training
ESTCP Training Resources
M2S2 Webinar - Communicating Classification to Stakeholders 4
At the First Planning Meeting
There is a big change here but it may not be what you think wersquove always left metal in the ground
missed detections due to obstructions anomalies below threshold
we just didnrsquot know much about that metal
Using classification we know a lot about the items we leave in the ground and we have put quality systems in place to prove it
M2S2 Webinar - Communicating Classification to Stakeholders 5
At the First Planning Meeting
Donrsquot exaggerate the capabilities of classification itrsquos a really cool technology
there really are no silver bullets
Seek buy-in on the remedial action objectives defined and quantitative RAOs make classification much easier
should have been spelled out in the DD or ROD
M2S2 Webinar - Communicating Classification to Stakeholders 6
At the First Planning Meeting
Be ready with a thoughtfully-developed QAPP
This is the cornerstone of the QCQA process and should enable all team members to have confidence in the project results
M2S2 Webinar - Communicating Classification to Stakeholders 7
During the Course of the Project
Enforce the QC reporting schedule specified in the QAPP and make sure the QA Geophysicist stays up to date
Stakeholder confidence is increased by
early identification of QC issues careful and complete root cause analyses
prompt implementation of any required corrective actions
M2S2 Webinar - Communicating Classification to Stakeholders 8
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Training Resources
USACE Training
ITRC ldquoTech Regrdquo Guidance Document amp Internet-based Training
ESTCP Training Resources
M2S2 Webinar - Communicating Classification to Stakeholders 4
At the First Planning Meeting
There is a big change here but it may not be what you think wersquove always left metal in the ground
missed detections due to obstructions anomalies below threshold
we just didnrsquot know much about that metal
Using classification we know a lot about the items we leave in the ground and we have put quality systems in place to prove it
M2S2 Webinar - Communicating Classification to Stakeholders 5
At the First Planning Meeting
Donrsquot exaggerate the capabilities of classification itrsquos a really cool technology
there really are no silver bullets
Seek buy-in on the remedial action objectives defined and quantitative RAOs make classification much easier
should have been spelled out in the DD or ROD
M2S2 Webinar - Communicating Classification to Stakeholders 6
At the First Planning Meeting
Be ready with a thoughtfully-developed QAPP
This is the cornerstone of the QCQA process and should enable all team members to have confidence in the project results
M2S2 Webinar - Communicating Classification to Stakeholders 7
During the Course of the Project
Enforce the QC reporting schedule specified in the QAPP and make sure the QA Geophysicist stays up to date
Stakeholder confidence is increased by
early identification of QC issues careful and complete root cause analyses
prompt implementation of any required corrective actions
M2S2 Webinar - Communicating Classification to Stakeholders 8
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
At the First Planning Meeting
There is a big change here but it may not be what you think wersquove always left metal in the ground
missed detections due to obstructions anomalies below threshold
we just didnrsquot know much about that metal
Using classification we know a lot about the items we leave in the ground and we have put quality systems in place to prove it
M2S2 Webinar - Communicating Classification to Stakeholders 5
At the First Planning Meeting
Donrsquot exaggerate the capabilities of classification itrsquos a really cool technology
there really are no silver bullets
Seek buy-in on the remedial action objectives defined and quantitative RAOs make classification much easier
should have been spelled out in the DD or ROD
M2S2 Webinar - Communicating Classification to Stakeholders 6
At the First Planning Meeting
Be ready with a thoughtfully-developed QAPP
This is the cornerstone of the QCQA process and should enable all team members to have confidence in the project results
M2S2 Webinar - Communicating Classification to Stakeholders 7
During the Course of the Project
Enforce the QC reporting schedule specified in the QAPP and make sure the QA Geophysicist stays up to date
Stakeholder confidence is increased by
early identification of QC issues careful and complete root cause analyses
prompt implementation of any required corrective actions
M2S2 Webinar - Communicating Classification to Stakeholders 8
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
At the First Planning Meeting
Donrsquot exaggerate the capabilities of classification itrsquos a really cool technology
there really are no silver bullets
Seek buy-in on the remedial action objectives defined and quantitative RAOs make classification much easier
should have been spelled out in the DD or ROD
M2S2 Webinar - Communicating Classification to Stakeholders 6
At the First Planning Meeting
Be ready with a thoughtfully-developed QAPP
This is the cornerstone of the QCQA process and should enable all team members to have confidence in the project results
M2S2 Webinar - Communicating Classification to Stakeholders 7
During the Course of the Project
Enforce the QC reporting schedule specified in the QAPP and make sure the QA Geophysicist stays up to date
Stakeholder confidence is increased by
early identification of QC issues careful and complete root cause analyses
prompt implementation of any required corrective actions
M2S2 Webinar - Communicating Classification to Stakeholders 8
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
At the First Planning Meeting
Be ready with a thoughtfully-developed QAPP
This is the cornerstone of the QCQA process and should enable all team members to have confidence in the project results
M2S2 Webinar - Communicating Classification to Stakeholders 7
During the Course of the Project
Enforce the QC reporting schedule specified in the QAPP and make sure the QA Geophysicist stays up to date
Stakeholder confidence is increased by
early identification of QC issues careful and complete root cause analyses
prompt implementation of any required corrective actions
M2S2 Webinar - Communicating Classification to Stakeholders 8
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
During the Course of the Project
Enforce the QC reporting schedule specified in the QAPP and make sure the QA Geophysicist stays up to date
Stakeholder confidence is increased by
early identification of QC issues careful and complete root cause analyses
prompt implementation of any required corrective actions
M2S2 Webinar - Communicating Classification to Stakeholders 8
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Example Project Documentation
Surface Clearance Memo
IVS Tech Memo
Weekly QC Reports throughout the field work
Anomaly Selection Tech Memo
Intrusive Investigation Report
Final Analysis Report and Justification for Stop Dig Point
M2S2 Webinar - Communicating Classification to Stakeholders 9
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Surface Clearance Memo
Was everything found consistent with the CSM
Is there anything the analysts need to know
M2S2 Webinar - Communicating Classification to Stakeholders 10
CSM Evidence Found in Surface Sweep
37-mm projectile Y 236-in rocket Y 60-mm mortar Y 75-mm projectile Y 81-mm mortar N 3-in stokes mortar Y Unexpected munition N
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
IVS Tech Memo
Is the Sensor Functioning Properly and Ready to Collect Data
SLO Initial Dynamic IVS Seed Position 050 Accuracy
025
Y o
ffset
(m)
000
IVS Seed 1 IVS Seed 2
-025
-050 X offset (m)
-050 -025 000 025 050
M2S2 Webinar - Communicating Classification to Stakeholders 11
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
IVS Tech Memo Are the remedial objectives achievable
M2S2 Webinar - Communicating Classification to Stakeholders 12
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Anomaly Selection Tech Memo Were all the blind seeds detected within spec
M2S2 Webinar - Communicating Classification to Stakeholders 13
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Intrusive Investigation Report
Were all recovered items consistent with analystrsquos predictions
M2S2 Webinar - Communicating Classification to Stakeholders 14
SW-30825
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Intrusive Investigation Report
M2S2 Webinar - Communicating Classification to Stakeholders 15
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
What We Are Doing to Facilitate This
Develop a set of standard QC and QA plots in UX‑Analyze
Work hard at the QC interface between data collection and data analysis
Make sure both of the above are in line with the evolving QAPP template
M2S2 Webinar - Communicating Classification to Stakeholders 16
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
M2S2 Webinar - Communicating Classification to Stakeholders 17
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Contractor Stop Dig Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 18
23 digs past the last TOI
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Verify The Threshold
M2S2 Webinar - Communicating Classification to Stakeholders 19
200 digs past the last TOI
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 20
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Validate the Process
M2S2 Webinar - Communicating Classification to Stakeholders 21
200 digs past the last TOI
100 randomly selected
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
Verification and Validation
Involve the stakeholders early and often in planning
draft plan before field work
final plans after contractor completes field work
Verify the stop-dig threshold dig past the last TOI
Validate the whole process targeted investigation of items classified as likely clutter
M2S2 Webinar - Communicating Classification to Stakeholders 22
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23
For More Information
serdp-estcporg
Featured Initiatives gt Munitions Response Initiatives gt Classification Applied to Munitions Response
Or
Search ndash Classification Applied to Munitions Response
M2S2 Webinar - Communicating Classification to Stakeholders 23