79
cwk
CONTENTS
Brief introduction 1Qualification of Co., LTD 2Process flow 4BW elbow 6
BW tee and cross 8BW reducer 14
BW cap 18Lap joint stub end 19
45 BW 45 lateral tee 20Bend 21
Tolerances for BW fittings 22Return bends and elbows of tubular heater in petrochemical industry 23
Forged Large Size Tees 24Y WYE made up of steel plates 25
Pipe outside diameter and wall thickness 26SW fittings 30
THRD fittings 34Union 38
Tolerances for SW fittings and THRD fittings 40Swaged nipple 42
Hexagonal nipple 44Nipple 45
Outlet 46Flange 53
Generally used metal materials 54Referenced Weight Lists 62
Calculation Equation and Conversion of Units 76
contents
BRIEF INTRODUCTION
Brief introduction
co-Working Developing Co., Ltd is the expert
manufacturer of wrought fittings for pressure piping, and produces
all kinds of butt-welding, socket-welding, thread fittings, special fit-
tings and flanges of carbon steel, alloy steel and stainless steel etc.
We can produce products according to GB DL HG SH SY
ASME MSS DIN EN and other standards and also according to
the clients technical requirements.
The long-term experiences in the past years and excellent fabricat-
ing technics ensure the reliability of fittings. The products are widely
used in oil, chemistry, shipbuilding, paper making and electric indus-
tries and etc. Our products are also approved by the customers.
The complete technics and advanced equipment of inspection and
examination guarantee that during raw material acceptance, dimen-
sion and appearance examination, proof test, NDT examination and
so on, all the fittings meet the requirements of standards and the
purchase order.
The efficiently executing Quality Management System and the perfect
management software of products manufacturing make the processes
of manufacturing and services in a controlled status. The company
insists on gradual improvement to meet the customers satisfaction.
During the past years, on the basis of the safe experiences on the
important large equipments and the successful proof test, the fittings
made by our company can meet with the design requirements for
pressure piping.
Honesty is basic to strive for excellence. Providing safe and reliable
products for all walks of life is our unchangeable purpose.
GB DL HG SH SY ASMEMSS DIN EN
1
Qualification of Company Ltd.
Manufacture License of Special Equipment P.R.C
Certificate for Measurement Conformity
ISO 9001 2008Certificate of Quality Management Systems for ISO 9001 2008
ISO 14001 2004Certificate of Environmental Management Systems for ISO 14001 2004
OHSAS 18001 1999Certificate of Occupational Health and Safety Administration Systems for OHSAS 18001 1999
CE/PED Pressure Equipment Directive 97/23/EC Material Manufacturers Certificate
China Classification Society Certificate of Works Approval
Recognition for BV Mode Survey Scheme
QUALIFICATION OF COMPANY LTD.
TS
2
Certificate of the Member of China Petrochemical Materials Resource Market
Certificate of 1st Class Supplying Network of China Petroleum & Natual Gas Group
Certificate of Member of the Energy-ahead Network
Certificate of Production Recommendation lssude for Electricity Construction
Certificate of Appointed Production by Chemical Engineering Construction Standards
Member of China Standardization Committee on Piping Affiliated componentsTC237
QUALIFICATION OF COMPANY LTD.
TC262/SC3 Member of China Standardization Committee on Boilers and Pressure Vessels Standardiza-tion Subcommittee on Pressure Piping
Member of Safety & Technology Committee on Special Equipment Subcommittee onPressure Piping Governed by General Administration of Quality Supervision, Inspection andQuarantine of P.R.C
3
1 Material acceptance 2 Cutting
2B Heating
3 Forming 5 Machining process
3B Heat treatment
3C Proof test
4
4 /Shot blast/Acid washing
4B NDE examination
1 2
3 3 3B
4 4B 4B
7 8
7 /Painting/Passivation 8
Marking
8BPMI
9 Packing 10
Stockpi le & transport ion
5
6 Final products examination
2B 3 3
3C 4
4B 5
6
8B 9
9
10
6
90 /BW 90 LR/SR Elbow
45BW 45 LR Elbow
GB/T 12459 GB/T 13401 ASME B16.9
1520253240506580901001251502002503003504004505005506006507007508008509009501000105011001150120013001400150016001700180019002000
Outside Diameter at Bevel
Center to End
90 Elbows 45 Elbows
LR SR LR
A BNominal Size
DN NPS OD
1 , GB/T 10752 SH 3408 SH 3409 HG/T 21635HG/T 21631 SY/T 0510 DL/T 695 EN 10253
2
1/23/4111/411/2221/2331/2456810121416182022242628303234363840424446485256606468727680
21.326.733.442.248.360.373.088.9101.6114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0559.0610.0660.0711.0762.0813.0864.0914.0965.01016.01067.01118.01168.01219.01321.01422.01524.01626.01727.01829.01930.02032.0
383838485776951141331521902293053814575336106867628389149911067114312191295137214481524160016761753182919812134228624382591274328963048
--253238516476891021271522032543053564064575085596106607117628138649149651016106711181168121913211422152416261727182919302032
16192225293544515764799512715919022225428631834338140643847050253356560063266069572775982188394710101073113711991263
Notes:1) Besides these, GB/T 10752 SH 3408 SH 3409 HG/T 21635 HG/
T 21631 SY/T 0510 DL/T 695 EN 10253 etc.are also applied.2) The elbow with NPS over 80 shall be made subject to the sizes agreed
by purchaser and manufacturer.
BUTT-WELDING ELBOWS
7
GB/T 12459 GB/T 13401 ASME B16.9
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Outside Diameter at BevelNominal Size
DN NPS OD
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
21.3
26.7
33.4
42.2
48.3
60.3
73.0
88.9
101.6
114.3
141.3
168.3
219.1
273.0
323.8
355.6
406.4
457.0
508.0
559.0
610.0
660.0
711.0
762.0
813.0
864.0
914.0
965.0
1016.0
1067.0
1118.0
1168.0
1219.0
3D 3D
-
57
76
95
114
152
190
229
267
305
381
457
610
762
914
1067
1219
1372
1524
1676
1829
1981
2134
2286
2438
2591
2743
2896
3048
3200
3353
3505
3658
-
24
31
39
47
63
79
95
111
127
157
189
252
316
378
441
505
568
632
694
757
821
883
964
1010
1073
1135
1200
1264
1326
1389
1453
1516
Center to Center
180 ReturnsO K
Center to End
90 Elbows 45 ElbowsA B
-
-
41
52
62
81
100
121
140
159
197
237
313
391
467
533
610
686
762
838
914
-
-
-
-
-
-
-
-
-
-
-
-
LR
76
76
76
95
114
152
190
229
267
305
381
457
610
762
914
1067
1219
1372
1524
1676
1829
-
-
-
-
-
-
-
-
-
-
-
-
-
-
51
64
76
102
127
152
178
203
254
305
406
508
609
711
813
914
1016
1118
1219
-
-
-
-
-
-
-
-
-
-
-
-
48
51
56
70
83
106
132
159
184
210
262
313
414
518
619
711
813
914
1016
1118
1219
-
-
-
-
-
-
-
-
-
-
-
-
SR LR SR
Back to Face
90 3DBW 90 3D Elbow
45 3DBW 45 3D Elbow
180 /BW 180 LR/SR Return
BUTT-WELDING ELBOWS
8
GB/T 12459 GB/T 13401 ASME B16.9
1515 1015 82020 1520 102525 2025 153232 2532 2032 154040 3240 2540 2040 155050 4050 3250 2550 206565 5065 4065 3265 258080 6580 5080 4080 329090 8090 6590 5090 40100100 90100 80100 65100 50100 40
Outside Diameter at BevelNominal Size
DN
Center to End
C M
BW Straight Tee BW Straight Cross
OD1 OD2NPS
1/21/2 3/81/2 1/43/43/4 1/23/4 3/811 3/41 1/211/411/4 111/4 3/411/4 1/211/211/2 11/4
11/2 111/2 3/411/2 1/222 11/2
2 11/4
2 12 3/421/221/2 221/2 11/2
21/2 11/4
21/2 133 21/2
3 23 11/2
3 11/4
31/231/2 331/2 21/2
31/2 231/2 11/2
44 31/2
4 34 21/2
4 24 11/2
21.321.3 17.121.3 13.726.726.7 21.326.7 17.133.433.4 26.733.4 21.342.242.2 33.442.2 26.742.2 21.348.348.3 42.248.3 33.448.3 26.748.3 21.360.360.3 48.360.3 42.260.3 33.460.3 26.773.073.0 60.373.0 48.373.0 42.273.0 33.488.988.9 73.088.9 60.388.9 48.388.9 42.2101.6101.6 88.9101.6 73.0101.6 60.3101.6 48.3114.3114.3 101.6114.3 88.9114.3 73.0114.3 60.3114.3 48.3
252525292929383838484848485757575757646057514476706764578683767370959289837910510298958986
25
29
38
48
57
64
76
86
95
105
BUTT-WELDING TEES AND CROSSES
9
GB/T 12459 GB/T 13401 ASME B16.9
125125 100125 90125 80125 65125 50150150 125150 100150 90150 80150 65200200 150200 125200 100200 90250250 200250 150250 125250 100300300 250300 200300 150300 125350350 300350 250350 200350 150400400 350400 300400 250400 200400 150
Outside Diameter at BevelNominal Size
DN
Center to End
C M
BW Reducing Tee BW Reducing Cross
OD1 OD2NPS
55 45 31/2
5 35 21/2
5 266 56 46 31/2
6 36 21/2
88 68 58 48 31/2
1010 810 610 510 41212 1012 812 612 51414 1214 1014 814 61616 1416 1216 1016 816 6
141.3141.3 114.3141.3 101.6141.3 88.9141.3 73.0141.3 60.3168.3168.3 141.3168.3 114.3168.3 101.6168.3 88.9168.3 73.0219.1219.1 168.3219.1 141.3219.1 114.3219.1 101.6273.0273.0 219.1273.0 168.3273.0 141.3273.0 114.3323.8323.8 273.0323.8 219.1323.8 168.3323.8 141.3355.6355.6 323.8355.6 273.0355.6 219.1355.6 168.3406.4406.4 355.6406.4 323.8406.4 273.0406.4 219.1406.4 168.3
124117114111108105143137130127124121178168162156152216203194191184254241229219216279270257248238305305295283273264
124
143
178
216
254
279
305
BUTT-WELDING TEES AND CROSSES
10
450450 400450 350450 300450 250450 200500500 450500 400500 350500 300500 250500 200550550 500550 450550 400550 350550 300550 250600600 550600 500600 450600 400600 350600 300600 250650650 600650 550650 500650 450650 400650 350650 300700700 650700 600700 550700 500700 450700 400700 350700 300750750 700750 650750 600750 550750 500750 450750 400750 350750 300750 250
Outside Diameter at BevelNominal Size
DN
Center to End
C MOD1 OD2NPS
1818 1618 1418 1218 1018 82020 1820 1620 1420 1220 1020 82222 2022 1822 1622 1422 1222 102424 2224 2024 1824 1624 1424 1224 102626 2426 2226 2026 1826 1626 1426 122828 2628 2428 2228 2028 1828 1628 1428 123030 2830 2630 2430 2230 2030 1830 1630 1430 1230 10
457.0457.0 406.4457.0 355.6457.0 323.8457.0 273.0457.0 219.1508.0508.0 457.0508.0 406.4508.0 355.6508.0 323.8508.0 273.0508.0 219.1559.0559.0 508.0559.0 457.0559.0 406.4559.0 355.6559.0 323.8559.0 273.0610.0610.0 559.0610.0 508.0610.0 457.0610.0 406.4610.0 355.6610.0 323.8610.0 273.0660.0660.0 610.0660.0 559.0660.0 508.0660.0 457.0660.0 406.4660.0 355.6660.0 323.8711.0711.0 660.0711.0 610.0711.0 559.0711.0 508.0711.0 457.0711.0 406.4711.0 355.6711.0 323.8762.0762.0 711.0762.0 660.0762.0 610.0762.0 559.0762.0 508.0762.0 457.0762.0 406.4762.0 355.6762.0 323.8762.0 273.0
343330330321308298381368356356346333324419406394381381371359432432432419406406397384495483470457444432432422521521508495483470457457448559546546533521508495483483473460
343
381
419
432
495
521
559
BW TEES & CROSSES
BUTT-WELDING TEES AND CROSSES
11
800800 750800 700800 650800 600800 550800 500800 450800 400800 350850850 800850 750850 700850 650850 600850 550850 500850 450850 400900900 850900 800900 750900 700900 650900 600900 550900 500900 450900 400950950 900950 850950 800950 750950 700950 650950 600950 550950 500950 45010001000 9501000 9001000 8501000 8001000 7501000 7001000 6501000 6001000 5501000 5001000 450
Outside Diameter at BevelNominal Size
DN
Center to End
C MOD1 OD2NPS
3232 3032 2832 2632 2432 2232 2032 1832 1632 143434 3234 3034 2834 2634 2434 2234 2034 1834 163636 3436 3236 3036 2836 2636 2436 2236 2036 1836 163838 3638 3438 3238 3038 2838 2638 2438 2238 2038 184040 3840 3640 3440 3240 3040 2840 2640 2440 2240 2040 18
813.0813.0 762.0813.0 711.0813.0 660.0813.0 610.0813.0 559.0813.0 508.0813.0 457.0813.0 406.4813.0 355.6864.0864.0 813.0864.0 762.0864.0 711.0864.0 660.0864.0 610.0864.0 559.0864.0 508.0864.0 457.0864.0 406.4914.0914.0 864.0914.0 813.0914.0 762.0914.0 711.0914.0 660.0914.0 610.0914.0 559.0914.0 508.0914.0 457.0914.0 406.4965.0965.0 914.0965.0 864.0965.0 813.0965.0 762.0965.0 711.0965.0 660.0965.0 610.0965.0 559.0965.0 508.0965.0 457.01016.01016.0 965.01016.0 914.01016.0 864.01016.0 813.01016.0 762.01016.0 711.01016.0 660.01016.0 610.01016.0 559.01016.0 508.01016.0 457.0
597584572572559546533521508508635622610597597584572559546533673660648635622622610597584572559711711698686673648648635622610597749749737724711698673673660648635622
597
635
673
711
749
BW TEES & CROSSES
BUTT-WELDING TEES AND CROSSES
12
10501050 10001050 9501050 9001050 8501050 8001050 7501050 7001050 6501050 6001050 5501050 5001050 4501050 40011001100 10501100 10001100 9501100 9001100 8501100 8001100 7501100 7001100 6501100 6001100 5501100 50011501150 11001150 10501150 10001150 9501150 9001150 8501150 8001150 7501150 7001150 6501150 6001150 55012001200 11501200 11001200 10501200 10001200 9501200 9001200 8501200 8001200 7501200 7001200 6501200 6001200 550
Outside Diameter at BevelNominal Size
DN
Center to End
C MOD1 OD2NPS
4242 4042 3842 3642 3442 3242 3042 2842 2642 2442 2242 2042 1842 164444 4244 4044 3844 3644 3444 3244 3044 2844 2644 2444 2244 204646 4446 4246 4046 3846 3646 3446 3246 3046 2846 2646 2446 224848 4648 4448 4248 4048 3848 3648 3448 3248 3048 2848 2648 2448 22
1067.01067.0 1016.01067.0 965.01067.0 914.01067.0 864.01067.0 813.01067.0 762.01067.0 711.01067.0 660.01067.0 610.01067.0 559.01067.0 508.01067.0 457.01067.0 406.41118.01118.0 1067.01118.0 1016.01118.0 965.01118.0 914.01118.0 864.01118.0 813.01118.0 762.01118.0 711.01118.0 660.01118.0 610.01118.0 559.01118.0 508.01168.01168.0 1118.01168.0 1067.01168.0 1016.01168.0 965.01168.0 914.01168.0 864.01168.0 813.01168.0 762.01168.0 711.01168.0 660.01168.0 610.01168.0 559.01219.01219.0 1168.01219.0 1118.01219.0 1067.01219.0 1016.01219.0 965.01219.0 914.01219.0 864.01219.0 813.01219.0 762.01219.0 711.01219.0 660.01219.0 610.01219.0 559.0
711711711711711711711698698660660660648635762762749737724724711711698698698686686800800787775762762749749737737737724724838838838813813813787787787762762762737737
762
813
851
889
BW TEES & CROSSES
BUTT-WELDING TEES AND CROSSES
13
13001300 12001300 11001300 100014001400 13001400 12001400 110015001500 14001500 13001500 120016001600 15001600 14001600 13001600 120017001700 16001700 15001700 14001700 13001700 120018001800 17001800 16001800 15001800 14001800 13001800 120019001900 18001900 17001900 16001900 15001900 14001900 13001900 120020002000 19002000 18002000 17002000 16002000 15002000 14002000 13002000 1200
Outside Diameter at BevelNominal Size
DN
Center to End
C MOD1 OD2NPS
5252 4852 4452 405656 5256 4856 446060 5660 5260 486464 6064 5664 5264 486868 6468 6068 5668 5268 487272 6872 6472 6072 5672 5272 487676 7276 6876 6476 6076 5676 5276 488080 7680 7280 6880 6480 6080 5680 5280 48
1321.01321.0 1219.01321.0 1118.01321.0 1016.01422.01422.0 1321.01422.0 1219.01422.0 1118.01524.01524.0 1422.01524.0 1321.01524.0 1219.01626.01626.0 1524.01626.0 1422.01626.0 1321.01626.0 1219.01727.01727.0 1626.01727.0 1524.01727.0 1422.01727.0 1321.01727.0 1219.01829.01829.0 1727.01829.0 1626.01829.0 1524.01829.0 1422.01829.0 1321.01829.0 1219.01930.01930.0 1829.01930.0 1727.01930.0 1626.01930.0 1524.01930.0 1422.01930.0 1321.01930.0 1219.02032.02032.0 1930.02032.0 1829.02032.0 1727.02032.0 1626.02032.0 1524.02032.0 1422.02032.0 1321.02032.0 1219.0
914864813762965914864813101696591486410921067101696591411681143111810671016965124512191194116811181067101613201295127012451219116811181067139713721346132112951270121911681118
965
1041
1118
1194
1270
1320
1422
1499
BW TEES & CROSSES
1) , GB/T 10752 SH 3408 SH 3409HG/T 21635 HG/T 21631 SY/T 0510 DL/T 695 EN 10253
2) DN 650 NPS 26 DN 350NPS 14
M3)
Notes1) Besides the above mentioned standards, the standards of GB/T 10752 SH
3408 SH 3409 HG/T 21635 HG/T 21631 SY/T 0510 DL/T 695 EN 10253etc.are also applied.
2) For the straight tees and crosses with DN 650(NPS 26)and the reducing teesand crosses with DN 350(NPS 14 , the outlet sizes are recommended to use(that mean the other sizes may be applied).
3) For the tees and crosses with the sizes larger than that listed in the above table,they will be supplied subject to the sized agreed by purchaser and manufactureror according to manufacturer s size.
BUTT-WELDING TEES AND CROSSES
14
BW Concentric Reducer
a)Seamless
b)Weld
BUTT-WELDING REDUCERS
GB/T 12459 GB/T 13401 ASME B16.9
20 1520 1025 2025 1532 2532 2032 1540 3240 2540 2040 1550 4050 3250 2550 2065 5065 4065 3265 2580 6580 5080 4080 3290 8090 6590 5090 4090 32100 90100 80100 65100 50100 40125 100125 90125 80125 65125 50
Outside Diameter at BevelNominal Size
DN
End to End
HOD1 OD2NPS
3/4 1/23/4 3/81 3/41 1/211/4 111/4 3/411/4 1/211/2 11/4
11/2 111/2 3/411/2 1/22 11/2
2 11/4
2 12 3/421/2 221/2 11/2
21/2 11/4
21/2 13 21/2
3 23 11/2
3 11/4
31/2 331/2 21/2
31/2 231/2 11/2
31/2 11/4
4 31/2
4 34 21/2
4 24 11/2
5 45 31/2
5 35 21/2
5 2
26.7 21.326.7 17.133.4 26.733.4 21.342.2 33.442.2 26.742.2 21.348.3 42.248.3 33.448.3 26.748.3 21.360.3 48.360.3 42.260.3 33.460.3 26.773.0 60.373.0 48.373.0 42.273.0 33.488.9 73.088.9 60.388.9 48.388.9 42.2101.6 88.9101.6 73.0101.6 60.3101.6 48.3101.6 42.2114.3 101.6114.3 88.9114.3 73.0114.3 60.3114.3 48.3141.3 114.3141.3 101.6141.3 88.9141.3 73.0141.3 60.3
38
51
51
64
76
89
89
102
102
127
15
BW Eccentric Reducer
a)Seamless
b)Weld
BUTT-WELDING REDUCERS
GB/T 12459 GB/T 13401 ASME B16.9
150 125150 100150 90150 80150 65200 150200 125200 100200 90250 200250 150250 125250 100300 250300 200300 150300 125350 300350 250350 200350 150400 350400 300400 250400 200400 150450 400450 350450 300450 250450 200500 450500 400500 350500 300500 250550 500550 450550 400550 350550 300
Outside Diameter at BevelNominal Size
DN
End to End
HOD1 OD2NPS
6 56 46 31/2
6 36 21/2
8 68 58 48 31/2
10 810 610 510 412 1012 812 612 514 1214 1014 814 616 1416 1216 1016 816 618 1618 1418 1218 1018 820 1820 1620 1420 1220 1022 2022 1822 1622 1422 12
168.3 141.3168.3 114.3168.3 101.6168.3 88.9168.3 73.0219.1 168.3219.1 141.3219.1 114.3219.1 101.6273.0 219.1273.0 168.3273.0 141.3273.0 114.3323.8 273.0323.8 219.1323.8 168.3323.8 141.3355.6 323.8355.6 273.0355.6 219.1355.6 168.3406.4 355.6406.4 323.8406.4 273.0406.4 219.1406.4 168.3457.0 406.4457.0 355.6457.0 323.8457.0 273.0457.0 219.1508.0 457.0508.0 406.4508.0 355.6508.0 323.8508.0 273.0559.0 508.0559.0 457.0559.0 406.4559.0 355.6559.0 323.8
140
152
178
203
330
356
381
508
508
16
600 550600 500600 450600 400600 350600 300650 600650 550650 500650 450650 400650 350700 650700 600700 550700 500700 450700 400700 350750 700750 650750 600750 550750 500750 450750 400750 350800 750800 700800 650800 600800 550800 500850 800850 750850 700850 650850 600850 550900 850900 800900 750900 700900 650900 600900 550950 900950 850950 800950 750950 700950 650950 600
Outside Diameter at BevelNominal Size
DN
End to End
HOD1 OD2NPS
24 2224 2024 1824 1624 1424 1226 2426 2226 2026 1826 1626 1428 2628 2428 2228 2028 1828 1628 1430 2830 2630 2430 2230 2030 1830 1630 1432 3032 2832 2632 2432 2232 2034 3234 3034 2834 2634 2434 2236 3436 3236 3036 2836 2636 2436 2238 3638 3438 3238 3038 2838 2638 24
610.0 559.0610.0 508.0610.0 457.0610.0 406.4610.0 355.6610.0 323.8660.0 610.0660.0 559.0660.0 508.0660.0 457.0660.0 406.4660.0 355.6711.0 660.0711.0 610.0711.0 559.0711.0 508.0711.0 457.0711.0 406.4711.0 355.6762.0 711.0762.0 660.0762.0 610.0762.0 559.0762.0 508.0762.0 457.0762.0 406.4762.0 355.6813.0 762.0813.0 711.0813.0 660.0813.0 610.0813.0 559.0813.0 508.0864.0 813.0864.0 762.0864.0 711.0864.0 660.0864.0 610.0864.0 559.0914.0 864.0914.0 813.0914.0 762.0914.0 711.0914.0 660.0914.0 610.0914.0 559.0965.0 914.0965.0 864.0965.0 813.0965.0 762.0965.0 711.0965.0 660.0965.0 610.0
508
610
610
610
610
610
610
610
BW CONCENTRIC & ECCENTRIC REDUCERS
BUTT-WELDING REDUCERS
17
1000 9501000 9001000 8501000 8001000 7501000 7001050 10001050 9501050 9001050 8501050 8001050 7501050 7001100 10501100 10001100 9501100 9001100 8501100 8001150 11001150 10501150 10001150 9501150 9001150 8501200 11501200 11001200 10501200 10001200 9501200 9001300 12001300 11501300 11001300 10501300 10001400 13001400 12001400 11001400 10001500 14001500 13001500 12001500 1100
Outside Diameter at BevelNominal Size
DN
End to End
HOD1 OD2NPS
40 3840 3640 3440 3240 3040 2842 4042 3842 3642 3442 3242 3042 2844 4244 4044 3844 3644 3444 3246 4446 4246 4046 3846 3646 3448 4648 4448 4248 4048 3848 3652 4852 4652 4452 4252 4056 5256 4856 4456 4060 5660 5260 4860 44
1016.0 965.01016.0 914.01016.0 864.01016.0 813.01016.0 762.01016.0 711.01067.0 1016.01067.0 965.01067.0 914.01067.0 864.01067.0 813.01067.0 762.01067.0 711.01118.0 1067.01118.0 1016.01118.0 965.01118.0 914.01118.0 864.01118.0 813.01168.0 1118.01168.0 1067.01168.0 1016.01168.0 965.01168.0 914.01168.0 864.01219.0 1168.01219.0 1118.01219.0 1067.01219.0 1016.01219.0 965.01219.0 914.01321.0 1219.01321.0 1168.01321.0 1118.01321.0 1067.01321.0 1016.01422.0 1321.01422.0 1219.01422.0 1118.01422.0 1016.01524.0 1422.01524.0 1321.01524.0 1219.01524.0 1118.0
610
610
610
711
711
711
711
711
BW CONCENTRIC & ECCENTRIC REDUCERS
1) , GB/T 10752 SH 3408 SH 3409HG/T 21635 HG/T 21631 SY/T 0510 DL/T 695 EN 10253
2)
Notes1) Besides the above mentioned standards, the standards of GB/T 10752 SH
3408 SH 3409 HG/T 21635 HG/T 21631 SY/T 0510 DL/T 695 EN 10253etc.are also applied.
2 For the concentric and eccentric reducers with the sizes larger than that listed inthe above table, they will be supplied subject to the sizes agreed by purchaserand manufacturer or according to manufacturer s size.
BUTT-WELDING REDUCERS
18
GB/T 12459 GB/T 13401 ASME B16.9
ELimiting Wall Thickness
for Length E
BW Cap
4.573.814.574.835.085.597.117.628.138.649.65
10.9212.7012.7012.7012.7012.7012.7012.7012.7012.70
------------------------------------
Outside Diameter at Bevel
OD
21.326.733.442.248.360.373.088.9101.6114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0559.0610.0660.0711.0762.0813.0864.0914.0965.01016.01067.01118.01168.01219.0
15202532405065809010012515020025030035040045050055060065070075080085090095010001050110011501200
Nominal Size
DN NPS
1/23/4111/411/2221/2331/245681012141618202224262830323436384042444648
252538383838385164647689102127152165178203229254267267267267267267267305305305343343343
Length
E E1
2525383838445164767689
102127152178191203229254254305------------------------------------
1)2) E E 1
DN 650 NPS 26 E 1
Notes:1) The configuration of the cap is normal ellipse.2) Length E applies for the thickness not exceeding the Limiting Wall
Thickness, Length E1 applies for the thickness exceeding the LimittingWall Thickness.For the caps with DN 650 (NPS26), they will bemade subject to the sizes agreed between purchaser and manufactureror be supplied according to manufacturer s size.
BUTT-WELDING CAPS
19
GB/T 12459 ASME B16.9 MSS SP-43
Diameterof Lap
Lap Joint Stub End
354351647392105127140157186216270324381413470533584641692
1) PN 50 PN 110(300 600 )PN 150(900 )
PN 260 PN 420(1500 2500 )
2)( ) F
3) A R GB/T 9118.1 9118.2 ASME B16.5B R MSS SP-
4 3 F4) G ASME B16.5
ASME B16.5 K5) t
Notes:1) When the short type is used on the larger flanges with PN 50 and PN 110
(300 and 600 LB) and on flanges with PN 150(900 LB) and above, or thelong type is used on the larger flange with PN 260 and PN 420(1500 and2500LB), the length of the cylinder may be added to be feasible thewelding, the adding length shall be negotiated by manufacturer andpurchaser.
2) The thickness of joint shall be added if the TG and MFM contact surfaceof flange are used, and the adding thickness shall increase (not be in-cluded in) the base length F.
3) The radius of fillet R(type A) shall conform to the ones of loose flangesaccording to GB/T 9118.1 9118.2 or ASME B16.5. The radius of fillet R(type B) is only applied for the standards of MSS SP-43 with short lengthF.
4) The lap joint diameter G shall conform to the standard machined faceindicated in ASME B16.5 , and the back of joint shall be machined toconform to the surface of installation.When RJ used, the size K specifiedin ASME B 16.5 Shall apply.
5) The minimum lap joint thickness t shall not be less than the nominal pipewall thickness.
152025324050658090100125150200250300350400450500550600
Nominal Size
DN NPS
1/23/4111/411/2221/2331/245681012141618202224
OD of Cylinder
OD
22.828.135.043.649.962.475.391.3104.0116.7144.3171.3222.1277.2328.0359.9411.0462.0514.0565.0616.0
20.525.932.641.447.559.572.288.1100.8113.5140.5167.5218.3272.3323.1354.8405.6456.0507.0558.0609.0
Max. Min.
7676102102102152152152152152203203203254254305305305305305305
Length
F R
515151515164646476767689102127152152152152152152152
Radius of Fillet
Long Type Short Type A Bmax
33356881010111113131313131313131313
0.80.80.80.80.80.80.80.80.80.81.61.61.61.61.61.61.61.61.61.61.6
BUTT-WELDING LAP JOINT STUB END
G
20
Outside Diameter at Bevel
OD
21.326.733.442.248.360.373.088.9101.6114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0559.0610.0660.0711.0762.0813.0864.0914.0965.01016.01067.01118.01168.01219.01270.01321.01372.01422.01473.01524.0
45BW Straight 45 Lateral Tee
5050505764646476767690102127140152165178203216229254267286299311330350483508533559584610635660686711737762
15202532405065809010012515020025030035040045050055060065070075080085090095010001050110011501200125013001350140014501500
Nominal Size
DN
90108133184216230267280292343381445520610700787876953102911121207130814221524162617271829193020322134223523372438254026422743284529463048
Center to End
X and Y Z
1) X X2 NPS 20 14 45
L O D 2
Note:1) The value X of the reducing tee shall be according to the one matching to
the nominal size of branch pipe, but when the varying diameter of branchexceeds and includes two levels (for example NPS 20 14), the length Lnear the 45 angle shall be equal or larger than the OD2 of branch pipe.
45BW Reducing 45 Lateral Tee
NPS
1/23/4111/411/2221/2331/245681012141618202224262830323436384042444648505254565860
BUTT-WELDING LATERAL TEES
21
DL/T 515 SY/T 5257 ASME B16.49
DL/T 515 Pipe Bends for Power Station, SY/T 5257 Steel Bend for Oil and Gas Transmission, ASME B16.49 Factory-MadeWrought Steel Induction Bends for Transportation and Distribution Systems and or purchasing specification
Content
Standard
Item
:1)
,
Note:1) The general bevel ends are as the above.If specially required, the
purchase specification shall be performed.
Carbon Steel Alloy Steel Stainless Steel
Material
R 3OD ODR 3OD (OD is outside diameter of pipe)
RBend Radius
According to the specification of design documentation.Bend Angle
5 0 0 m mPer standard or specified length in the design documentation,or both straight lengths are 500mm.
LStraight Length
OD 1220mm ODOutside Diameter
According to the specification of design documentation. T
Wall Thickness
According to the bevel ends of BW fittings or per specification of design documentation.Bevel at Ends
BEVEL ENDS OF BW FITTINGS
T 22mm T 22mm
Bend
BUTT-WELDING BENDS
22
TOLERANCES FOR BW FITTINGS
Nominal Size
1)2 )
All Fittings
45 90
45 & 90Elbows
& Tees, Crosses
3D3D
Radius Elbows
180Returns Caps Reducers
& Lap JointStub Ends
Lap Joint Stub Ends
ID 3)DN NPS OD 3) 4) A B C M A B O K U E E1 H F G R t
15-65
80-90
100
125-200
250-450
500-600
650-750
800-1200
1300-1500
1600-1700
1800-2000
1/2 -21/2
3-31/2
4
5-8
10-18
20-24
26-30
32-48
52-60
64-68
72-80
+1.6-0.8
1.6
1.6
+2.4-1.6+4.0-3.2+6.4-4.8+6.4-4.8+6.4-4.8+6.4-4.8+6.4-4.8+6.4-4.8
0.8
1.6
1.6
1.6
3.2
4.8
4.8
4.8
4.8
4.8
4.8
2
2
2
2
2
2
3
5
5
5
5
3
3
3
3
3
3
6
6
---
---
---
6
6
6
6
10
10
---
---
---
---
---
6
6
6
6
6
6
---
---
---
---
---
1
1
1
1
2
2
---
---
---
---
---
3
3
3
6
6
6
10
10
---
---
---
2
2
2
2
2
2
5
5
---
---
---
0-10-10-10-10-20-2
---
---
---
---
---
0-10-10-20-20-20-2
---
---
---
---
---
+1.60
+1.60
+1.60
+1.60
+3.20
+3.20
---
---
---
---
---
12 87 .5%
34
Note:1) The inside diameter and the nominal wall thickness shall be specified by purchaser.2) If purchaser dosen t specify the thickness tolerance, 87.5% of the nominal thick-
ness shall be the min. thickness.3) Out of-roundness is the sum of absolute values of plus and minus tolerance.4) When the wall thickness needs increasing to meet the design requirement,the toler-
ance may excced the ones indicated in the above list.
Nominal Size Q P
DN NPS
15-100
125-200
250-300
350-400
450-600
650-750
800-1050
1100-1200
1300-2000
1/2 -4
5-8
10-12
14-16
18-24
26-30
32-42
44-48
50-80
1
2
3
3
4
5
5
5
5
2
4
5
6
10
10
13
19
19
TOLERANCES FOR BW FITTINGS
23
9090 Elbow
180Return Bend
TOLERANCES FOR RETURN BENDS & ELBOWS
SH/T 3065 SH/T 3065 RETURN BENDS & ELBOWS OF TUBULAR HEATER IN PETROCHEMICAL INDUSTRY
RETURN BENDS & ELBOWS
Item
ID
R
A
K
U
P
Q
T
OD
0.75
1.00
-
-
-
1.50
90 180 90 180 90 180 90 180
+1.50
-0.75
+1.50
-0.751.50 1.50
+2.00
-0.75
+2.00
-1.50
+2.00
-1.50
+2.00
-1.50
0.75
-
2.00
+6.00
1.00
2.00
1.50
1.50
-
-
-
1.50
1.50
-
2.50
+6.00
1.00
2.00
1.50
2.00
-
-
-
3.00
1.50
-
2.50
+6.00
1.00
4.00
1.50
2.00
-
-
-
3.00
1.50
-
3.00
+6.00
2.00
4.00
0.75 1.50
1 2 . 5 % T T T12.5%T ;If T is the min.one,the minus tolerance shall be zero.
OD 76 OD=89 127 OD=141 193 OD=219 237
Carbon steel Alloy steel Stainless steel
Content
Material
Item
Specified according to the design documentation.90 RBending radius(90 Elbow)
Specified according to the design documentation. T
Wall thickness
According to the bevel ends of BW fittings or the specification of design documentation.Bevel at ends
Specified according to the design documentation.180 A
Center to center(Return Bend)
24
JB 4726 4728 JB 4726 4728 Steel forgings for pressure vesselsDL 473 DL 473 Standard specification for large size tees.ASTM A105 ASTM A105 Standard Specification for Carbon Steel Forgings for Piping ApplicationsASTM A182 ASTM A182 Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves andParts for High-Temperature ServiceASTM A336 ASTM A336 Standard Specification for Alloy Steel Forgings for Pressure and High-Temperature PartsASTM A965 ASTM A965 Standard Specification for Austenitic Steel Forgings for Pressure and High Temperature Parts
Content
Standard
Item
1)
2)
a )
b )
Note:
1) Besides the above figures, others can also be manufactured per the purchase
specification..
2) Generally, the figures and the sizes will be specified per the following:
a) Purchaser provides the drawings and manufacturer will fabricate them
accordingly.
b) Per the provided specifications by purchasersuch as figures,outside diameters,
wall thicknesses,angels and etc,manufacturer provides the drawings for
purchaser s review,then manufacture after approval.
Using the processes of forging boring heat treatment ultrasonic examination and finishing.Fabrication Process
FORGED LARGE SIZE TEES
Carbon steel Alloy steel Stainless steelMaterial
Per the specification of design documentation or the agreement between manufacturer and purchaser.Size
Per the tolerace of BW fittings or the specification of design documentation.Tolerance
Per the bevel ends of BW fittings or specification of design documentation.Bevelends
45Forged Lateral 45 Tee
YForged WYE
TForged Tee
FORGED LARGE SIZE TEES
25
1Type 1
2Type 2
WYE
Using the processes of cutting steel plate rolling and welding.
Content
Forming Process
Item
1)2)
a )
b )
Note:1) Besides the above figures, others can also be manufactured per the purchase
specification..2) Generally, the figures and the sizes will be specified per the following:
a) Purchaser provides the drawings and manufacturer will fabricate them accordingly.b) Per the provided specifications by purchaser such as figures,outside diameters,
wall thicknesses,angels and etc, manufacturer provides the drawings for purchasers review,then manufacture after approval.
Carbon steel Alloy steel Stainless steelMaterial
YWYE MADE UP OF STEEL PLATES
According to the specification of design documentation or the agreement between manufacturer and purchaser. L
Structure length
According to the specification of design documentation. 0D
Outside Diameter
According to the specification of design documentation.Included Angle
According to the specification of design documentation. T
Thickness
According to the tolerance of BW fittings or the specification of design documentation.Tolerance
According to the bevel ends of BW fittings or specification of design documentation.Bevel at ends
26
GB ASME MSS ( )OUTSIDE DIAMETER AND WALL THICKNESS OF THE CONNECTING PIPE FORFITTING FER STANDARDS GB ASME MSS APPLYING FOR ALL MATERIALS)
Nominal Size OD T
Nominal Wall Thickness T
DN NPS OD
68
10152025324050658090
100125150200250300350400450500550600650700750800850900950
1000105011001150120013001400150016001700180019002000
1) ASME B36.10M GB ASME MSS
2)
Note1) The above digits quoted from B36.10M. The connecting pipe thickness of
fittings per standards GB, ASME and MSS also apply them.2) If the outside diameter and wall thickness of the connecting pipe aren t
included in the above table, these sizes can be specified directly in thepurchase order.
Sch10 Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140 Sch160 XXS
1/81/43/81/23/41
11/411/22
21/23
31/24568
10121416182022242628303234363840424446485256606468727680
10.313.717.121.326.733.442.248.360.373.088.9
101.6114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0559.0610.0660.0711.0762.0813.0864.0914.0965.0
1016.01067.01118.01168.01219.01321.01422.01524.01626.01727.01829.01930.02032.0
1.241.651.652.112.112.772.772.772.773.053.053.053.053.403.403.764.194.576.356.356.356.356.356.357.927.927.927.927.927.92
--------------
---------------
6.356.356.357.927.927.929.539.539.53
12.7012.7012.7012.7012.7012.70
--------------
1.451.851.852.412.412.902.973.183.184.784.784.784.78
--
7.047.808.389.539.5311.1312.7012.7014.27
-15.8815.8815.8815.8815.88
--------------
1.732.242.312.772.873.383.563.683.915.165.495.746.026.557.118.189.279.539.539.539.539.539.539.539.539.539.539.539.539.539.539.539.539.539.539.53
--------
1.732.242.312.772.873.383.563.683.915.165.495.746.026.557.118.189.27
10.3111.1312.7014.2715.09
-17.48
---
17.4817.4819.05
--------------
---------------
10.3112.7014.2715.0916.6619.0520.6222.2324.61
--------------------
2.413.023.203.733.914.554.855.085.547.017.628.088.569.53
10.9712.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.7012.70
--------
2.413.023.203.733.914.554.855.085.547.017.628.088.569.53
10.9712.7015.0917.4819.0521.4423.8326.1928.5830.96
--------------------
---------------
15.0918.2621.4423.8326.1929.3632.5434.9338.89
--------------------
------------
11.1312.7014.2718.2621.4425.4027.7930.9634.9338.1041.2846.02
--------------------
---------------
20.6225.4028.5831.7536.5339.6744.4547.6352.37
--------------------
---
4.785.566.356.357.148.749.5311.13
-13.4915.8818.2623.0128.5833.3235.7140.4945.2450.0153.9859.54
--------------------
---
7.477.829.099.70
10.1511.0714.0215.24
-17.1219.0521.9522.2325.4025.40
--------------------------
OUTSIDE DIAMETER AND WALL THICKNESS
27
Sch5S Sch10S Sch40S Sch80S
---
1.651.651.651.651.651.652.112.112.112.112.772.772.773.403.963.964.194.194.784.785.54
--
6.35
1.241.651.652.112.112.772.772.772.773.053.053.053.053.403.403.764.194.574.784.784.785.545.546.35
--
7.92
1.732.242.312.772.873.383.563.683.915.165.495.746.026.557.118.189.279.539.539.539.539.53
-9.53
---
2.413.023.203.733.914.554.855.085.547.017.628.088.569.53
10.9712.7012.7012.7012.7012.7012.7012.70
-12.70
---
OD
GB ASME MSS ( )OUTSIDE DIAMETER AND WALL THICKNESS OF THE CONNECTING PIPE FOR FITTING PERSTANDARDS GB ASME MSS(APPLYING FOR STAINLESS STEEL MATERIALS)
TNominal Wall Thickness T
1 ASME B36.19M GB ASME MSS
2
Note1) The above digits quoted from B36.19M. The connecting pipe thickness of
fittings per standards GB, ASME and MSS also apply them.2) If the outside diameter and wall thickness of the connecting pipe aren t
included in the above table, these sizes can be specified directly in thepurchase order.
OD
Nominal Size
NPS
1/81/43/81/23/41
11/411/22
21/23
31/24568
1012141618202224262830
DN
68
10152025324050658090
100125150200250300350400450500550600650700750
10.313.717.121.326.733.442.248.360.373.088.9
101.6114.3141.3168.3219.1273.0323.8355.6406.4457.0508.0559.0610.0660.0711.0762.0
OUTSIDE DIAMETER AND WALL THICKNESS
28
Nominal PressurePN(MPa)
GB/T 12459 GB/T 13401HG/T 21631
OUTSIDE DIAMETER ( SERIES) OF GB/T 12459 &GB/T 13401 AND OUTSIDE DIAMETER ANDWALLTHICKNESS( SERIES) OF HG/T 21631
1) GB/T 12459 GB/T 134012 6 2 7
2) HG/T 21631 HGJ 5282 6 2 7
3) HG/T 21635 HGJ 514
26 27
Note1) The outside diameter( series)of GB/T 12459 and GB/T 13401 standards shall be
per the one indicated in the above table; The wall thickness of series can be perthe table in page 26 27 or be specified directly in the purchase order.
2) The outside diameter and wall thickness of HG/T 21631 previousely HGJ 528standards have the series of system and system, and the outside diameterand wall thickness of series are in accordance with the ones in the table of page26 27.
3) The outside diameter and wall thickness of HG/T 21635 previousely HGJ 514standard have the series of metric system and inch system, and the outsidediameter and wall thickness of inch system are in accordance with the ones in thetable of page 26 27.
1.6
NominalSize
DN
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
OD
OD
CS SS CS SS CS SS
1.0 2.5
18
25
32
38
45
57
76
89
108
133
159
219
273
325
377
426
480
530
630
720
820
920
1020
1120
1220
-
-
-
-
-
-
-
-
-
-
5
5
5
6
6
6
7
7
8
8
9
9
10
-
-
-
-
-
-
-
-
-
-
-
-
3.5
3.5
3.5
4.0
4.5
4.5
5.0
5.5
6.0
7.0
7.0
8.0
-
-
-
-
-
-
-
-
-
-
-
-
-
5.5
6.0
6.0
7.0
7.0
8.0
8.0
9.0
10
11
12
13
14
-
-
-
-
-
-
-
-
-
-
-
-
4.0
4.0
4.5
5.0
6.0
6.0
7.0
7.0
8.0
9.0
10
-
-
-
-
-
-
-
-
-
-
-
-
-
-
6.0
7.0
8.0
8.0
9.0
10
11
12
13
15
16
-
-
-
-
-
-
-
-
-
-
-
-
-
-
5.0
5.0
6.0
7.0
8.0
9.0
9.0
10
12
13
15
-
-
-
-
DN OD
NominalSize
OD Nominal PressurePN(MPa)
15
20
25
32
40
50
65
80
100
125
150
200
250
300
350
400
450
500
600
700
800
900
1000
1100
1200
18
25
32
38
45
57
76
89
108
133
159
219
273
325
377
426
480
530
630
720
820
920
1020
1120
1220
-
-
3.0
3.0
3.5
3.5
4.0
4.0
4.0
4.0
4.5
6.0
7.0
8.0
9.0
9.0
9.0
9.0
9.0
-
-
-
-
-
-
-
-
3.0
3.0
3.5
3.5
4.0
4.0
4.0
4.0
4.5
6.0
7.0
8.0
9.0
11
-
-
-
-
-
-
-
-
-
-
-
3.0
3.5
3.5
3.5
4.5
5.0
6.0
6.0
7.0
9.0
11
12
-
-
-
-
-
-
-
-
-
-
-
-
-
4.0
4.5
4.5
5.0
6.0
7.0
8.0
9.0
10
12
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5 4.0 6.4 10.0
HG/T 21635OUTSIDE DIAMETER AND WALLTHICKNESS(METRIC SYSTEM)OFHG/T 21635
OUTSIDE DIAMETER AND WALL THICKNESS
29
SHOUTSIDE DIAMETER AND WALL THICKNESS OF THE CONNECTING PIPE FOR FIT-TING PER STANDARDS SH
NominalSize
OD T
Nominal Wall Thickness T
DN OD
10
15
20
25
(32)
40
50
(65)
80
100
(125)
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
1 SNote1) Schedule with the suffix s only applies for stainless steel.
Sch5s
Sch10s
Sch20s
Sch40s
Sch80s
Sch20
Sch30
Sch40
Sch60
Sch80
Sch100
Sch120
Sch140
Sch160
XXS
17
22
27
34
42
48
60
76
89
114
140
168
219
273
325
356
406
457
508
559
610
660
711
762
813
864
914
965
1016
1118
1220
1321
1420
1524
1620
1727
1820
1930
2020
1.2
1.6
1.6
1.6
1.6
1.6
1.6
2.0
2.0
2.0
2.8
2.8
2.8
3.5
4.0
4.0
4.5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
1.6
2.0
2.0
2.8
2.8
2.8
2.8
3.0
3.0
3.0
3.5
3.5
4.0
4.0
4.5
5.0
5.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.0
2.5
2.5
3.0
3.0
3.0
3.5
3.5
4.0
4.0
5.0
5.0
6.5
6.5
6.5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5
3.0
3.0
3.5
3.5
4.0
4.0
5.0
5.5
6.0
6.5
7.0
8.0
9.5
9.5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3.2
4.0
4.0
4.5
5.0
5.0
5.5
7.0
7.5
8.5
9.5
11.0
13.0
15.0
17.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3.5
4.5
4.5
5.0
5.0
5.5
6.5
6.5
6.5
8.0
8.0
8.0
9.5
9.5
9.5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
6.5
7.0
8.0
8.5
9.5
9.5
11.0
13.0
13.0
14.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.5
3.0
3.0
3.5
3.5
4.0
4.0
5.0
5.5
6.0
6.5
7.0
8.0
9.5
10.0
11.0
13.0
14.0
15.0
17.0
18.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
5.0
6.0
6.5
7.0
8.0
9.5
10.0
13.0
14.0
15.0
17.0
19.0
20.0
22.0
25.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3.5
4.0
4.0
4.5
5.0
5.0
5.5
7.0
7.5
8.5
9.5
11.0
13.0
15.0
17.0
19.0
22.0
24.0
26.0
28.0
32.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
15.0
18.0
22.0
24.0
26.0
30.0
32.0
35.0
38.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
7.0
8.0
9.0
11.0
13.0
14.0
18.0
22.0
25.0
28.0
32.0
35.0
38.0
42.0
45.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
20.0
25.0
28.0
32.0
36.0
40.0
45.0
48.0
52.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
5.0
5.5
6.5
6.5
7.0
8.5
9.5
11.0
14.0
16.0
18.0
24.0
28.0
34.0
36.0
40.0
45.0
50.0
54.0
60.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
7.5
8.0
9.0
10.0
10.0
11.0
14.0
15.0
17.0
19.0
22.0
23.0
25.0
26.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
OUTSIDE DIAMETER AND WALL THICKNESS
30
GB/
T 14
383
ASM
E B1
6.11
SW
Cro
ss45
SW
45
Elb
ow90
SW
90
Elb
owSW
Tee
6 8 10 15 20 25 32 40 50 65 80 100
:1) 2)
B1
6.1
13)
Not
e:1)
The
even
thic
knes
s ar
ound
the
sock
et b
ore
shal
l not
be
less
than
the
aver
age
valu
e, th
e th
ickn
ess
at p
artia
l are
as c
an b
e th
e m
in. o
ne.
2)C
onsi
derin
g th
e to
lera
nce
of o
utsi
de d
iam
eter
of p
ipe,
the
diam
eter
s of
som
e so
cket
bor
e ca
n be
a lit
tle la
rger
than
the
ones
spe
cifie
d in
B16
.11.
3)W
hen
the
size
s of
the
conn
ectin
g pi
pes
aren
t con
form
ed to
the
ones
spe
cifie
d in
this
cat
alog
,th
e si
zes
of th
e co
nnec
ting
pipe
s sh
all b
e pr
ovid
ed in
the
purc
hase
spe
cific
atio
n.
Nom
inal
Siz
e
DN
Soc
ket
Bor
e D
ia.
Bor
e D
ia. o
f Fitt
ings
Soc
ket W
all T
hick
ness
Bod
y W
all
Dep
th o
fS
ocke
tC
ente
r to
Bot
tom
of S
ocke
t
NP
SB
DC
Gm
in
J min
A
3000
6000
9000
3000
6000
9000
ave
min
ave
min
ave
min
3000
6000
9000
90E
lbow
,Tee
,Cro
ss
3000
45E
lbow
6000
9000
3000
6000
9000
1/8
1/4
3/8
1/2
3/4 1 11 /4 11 /2 2 21 /2 3 4
10.9
14.3
17.7
21.9
27.3
34.0
42.8
48.9
61.2
73.9
89.9
115.
5
6.1
8.5
11.8
15.0
20.2
25.9
34.3
40.1
51.7
61.2
76.4
100.
7
3.2
5.6
8.4
11.0
14.8
19.9
28.7
33.2
42.1 - - -
- - - 5.6
10.3
14.4
22.0
27.2
37.4 - - -
3.18
3.78
4.01
4.67
4.90
5.69
6.07
6.35
6.93
8.76
9.52
10.6
9
3.18
3.30
3.50
4.09
4.27
4.98
5.28
5.54
6.04
7.62
8.30
9.35
3.96
4.60
5.03
5.97
6.96
7.92
7.92
8.92
10.9
2
- - -
3.43
4.01
4.37
5.18
6.04
6.93
6.93
7.80
9.50 - - -
- - -
9.53
9.78
11.3
8
12.1
4
12.7
0
13.8
4
- - -
- - -
8.18
8.56
9.96
10.6
2
11.1
2
12.1
2
- - -
2.41
3.02
3.20
3.73
3.91
4.55
4.85
5.08
5.54
7.01
7.62
8.56
3.15
3.68
4.01
4.78
5.56
6.35
6.35
7.14
8.74 - - -
- - -
7.47
7.82
9.09
9.70
10.1
5
11.0
7
- - -
9.5
9.5
9.5
9.5
12.5
12.5
12.5
12.5
16.0
16.0
16.0
19.0
11.0
11.0
13.5
15.5
19.0
22.5
27.0
32.0
38.0
41.0
57.0
66.5
11.0
13.5
15.5
19.0
22.5
27.0
32.0
38.0
41.0 - - -
- - -
25.5
28.5
32.0
35.0
38.0
54.0 - - -
8.0
8.0
8.0
11.0
13.0
14.0
17.5
20.5
25.5
28.5
32.0
41.0
8.0
8.0
11.0
12.5
14.0
17.5
20.5
25.5
28.5 - - -
- - -
15.5
19.0
20.5
22.5
25.5
28.5 - - -
SOCKET-WELDING FITTINGS
31
GB/
T 14
383
ASM
E B1
6.11
SW C
oupl
ing
SW H
alf-C
oupl
ing
Bos
s45
SW
45
Late
ral
SOCKET-WELDING FITTINGS
Cen
ter t
o B
otto
m o
f Soc
ket
Km
in
3000
6000
4.8
4.8
4.8
6.4
6.4
9.6
9.6
11.2
12.7
15.7
19.0
22.4
6.4
6.4
6.4
7.9
7.9
11.2
11.2
12.7
15.7
19.0
22.4
28.4
9000
3000
6000
3000
- - -
11.2
12.7
14.2
14.2
15.7
19.0 - - -
- - 37 41 51 60 71 81 98 151
184
201
- - - 51 60 71 81 98 151 - - -
- - 9.5
9.5 11 13 16 17 21 30 57 66
():
4)B
JD
5) 6)
Not
e(co
ntin
ued)
:4)
Whe
n th
e fit
tings
are
redu
cing
,the
stru
ctur
e si
zes
shal
l be
sam
e as
the
ones
of t
he s
traig
ht fi
tting
san
d B
JD
sha
ll be
mac
hine
d pe
r the
acc
ordi
ng re
duci
ng e
nds.
5)C
oupl
ings
can
be
the
conc
entri
c or
ecc
entri
c ty
pe.
6)Fi
tting
can
als
o be
man
ufac
ture
d as
the
mix
ed c
onne
ctin
gs o
f SW
and
TH
RD
.
6 8 10 15 20 25 32 40 50 65 80 100
Nom
inal
Siz
e
DN
Soc
ket
Bor
e D
ia.
NP
SB
1/8
1/4
3/8
1/2
3/4 1 11 /4 11 /2 2 21 /2 3 4
10.9
14.3
17.7
21.9
27.3
34.0
42.8
48.9
61.2
73.9
89.9
115.
5
Bor
e D
ia. o
f Fitt
ings
Soc
ket W
all T
hick
ness
Bod
y W
all
DC
Gm
in
3000
6000
9000
3000
6000
9000
ave
min
ave
min
ave
min
3000
6000
9000
6.1
8.5
11.8
15.0
20.2
25.9
34.3
40.1
51.7
61.2
76.4
100.
7
3.2
5.6
8.4
11.0
14.8
19.9
28.7
33.2
42.1 - - -
- - - 5.6
10.3
14.4
22.0
27.2
37.4 - - -
3.18
3.78
4.01
4.67
4.90
5.69
6.07
6.35
6.93
8.76
9.52
10.6
9
3.18
3.30
3.50
4.09
4.27
4.98
5.28
5.54
6.04
7.62
8.30
9.35
3.96
4.60
5.03
5.97
6.96
7.92
7.92
8.92
10.9
2
- - -
3.43
4.01
4.37
5.18
6.04
6.93
6.93
7.80
9.50 - - -
- - -
9.53
9.78
11.3
8
12.1
4
12.7
0
13.8
4
- - -
- - -
8.18
8.56
9.96
10.6
2
11.1
2
12.1
2
- - -
2.41
3.02
3.20
3.73
3.91
4.55
4.85
5.08
5.54
7.01
7.62
8.56
3.15
3.68
4.01
4.78
5.56
6.35
6.35
7.14
8.74 - - -
- - -
7.47
7.82
9.09
9.70
10.1
5
11.0
7
- - -
Dep
th o
fS
ocke
t
J min
9.5
9.5
9.5
9.5
12.5
12.5
12.5
12.5
16.0
16.0
16.0
19.0
End
Wal
l Thi
ckne
ssLa
ying
Leng
ths
Layi
ngLe
ngth
s
EF
6.5
6.5
6.5
9.5
9.5
12.5
12.5
12.5
19.0
19.0
19.0
19.0
16.0
16.0
17.5
22.5
24.0
28.5
30.0
32.0
41.0
43.0
44.5
48.0
6000
AH
- - - 11 13 16 17 21 30 - - -
SW C
ap
32
Cm
in
3000
3.8
4.0
3.8
4.7
4.0
3.8
4.9
4.7
4.0
3.8
5.7
4.9
4.7
4.0
3.8
6000
3000
6000
3000
4.6
5.0
4.6
6.0
5.0
4.6
7.0
6.0
5.0
4.6
7.9
7.0
6.0
5.0
4.6
14.2
15.7
15.7
17.5 - -
19.1 - - -
20.6 - - - -
15.7
15.7
15.7
19.1
19.1 -
20.6
20.6 - -
22.4 - - - -
- - -
27.0
27.0 - -
28.5
28.5
28.5 -
31.8
31.8
31.8
31.8
Bore
6000
SL
RL m
in
- - - -
32.0 - - -
33.3
33.3 -
34.8
34.8
34.8
34.8
Leng
th
3000
6000
3000
19.1
20.6
20.6
22.4
15.7
17.5
23.9
15.7
17.5
19.1
25.4
17.5
19.1
20.6
22.4
21.3
23.1
20.6
25.4
22.4
22.4
28.5
28.5
22.4
23.9
30.2
20.6
22.4
23.9
25.4
9.2
12.5
9.2
15.8
12.5
9.2
20.9
15.8
12.5
9.2
26.6
20.9
15.8
12.5
9.2
6000
AD
6.4
9.1
6.4
11.8
9.1
6.4
15.5
11.8
9.1
6.4
20.7
15.5
11.8
9.1
6.4
108
1510
8
2015
10
8
2520
15
10
8
3225
20
15
10
8
Nom
inal
Siz
e
DN
NP
S
3/8
1/4
1/2
3/8
1/
4
3/4
1/2
3/
8
1/
4
13/
4
1/
2
3/
8
1/
4
11 /4
1
3/4
1/2
3/8
1/4
1 1 1 1 2 2 1 2 2 2 1 2 2 2 2
Type
3000
6000 1 1 1 1 1 2 1 1 2 2 1 2 2 2 2
Layi
ng L
engt
hW
all
Soc
ket B
ore
Dia
.S
hank
Dia
.
B 14.3
17.7
14.3
21.9
17.7
14.3
27.3
21.9
17.7
14.3
34.0
27.3
21.9
17.7
14.3
9.5
9.5
9.5
9.5
9.5
9.5
12.5
9.5
9.5
9.5
12.5
12.5
9.5
9.5
9.5
Dep
th o
fS
ocke
t
K m
inS
D
17.1
21.3
26.7
33.4
42.2
MSS
SP-
79M
SS S
P-79
SW
RED
UCE
R IN
SERT
S
2 Type
21 Ty
pe 1
SW REDUCER INSERTS
33
C m
in
3000
6.1
5.7
4.9
4.7
4.0
6.4
6.1
5.7
4.9
4.7
6.9
6.4
6.1
5.7
4.9
8.8
6.9
6.4
6.1
5.7
9.5
8.8
6.9
6.4
6.1
6000
3000
6000
3000
7.9
7.9
7.0
6.0
5.0
8.9
7.9
7.9
7.0
6.0
10.9
8.9
7.9
7.9
7.0
11.9
10.9
8.9
7.9
7.9
13.8
12.5
11.0
8.9
7.9
22.4 - - - -
25.4 - - - -
38.1 - - - -
31.8 - - - - - - - - -
25.4
25.4 - - -
28.7 - - - -
31.8 - - - -
44.5 - - - - - - - - -
-
33.3
33.3
33.3
33.3 -
38.1
38.1
38.1
38.1 -
53.9
53.9
53.9
53.9 -
47.5
47.5
47.5
47.5
60.5
60.5
60.5
60.5
60.5
Bore
6000
SL
RL
min
- -
39.6
39.6
39.6 -
41.2
41.2
41.2
41.2 -
53.9
53.9
53.9
53.9 -
53.9
53.9
53.9
53.9 - - - - -
Leng
th
3000
6000
3000
28.5
17.5
19.1
20.6
22.4
31.8
20.6
22.4
23.9
25.4
46.0
35.1
36.6
38.1
39.6
38.1
25.4
28.5
30.2
31.8
33.3
38.1
38.1
41.2
42.9
35.1
29.2
25.4
26.9
28.5
38.9
23.9
25.4
26.9
28.5
42.7
35.1
36.6
38.1
38.1
57.2
31.8
31.8
31.8
31.8
54.0
54.0
54.0
57.0
57.0
35.1
26.6
20.9
15.8
12.5
40.9
35.1
26.6
20.9
15.8
52.5
40.9
35.1
26.6
20.9
62.7
52.5
40.9
35.1
26.6
77.9
62.7
52.5
40.9
35.1
6000
AD
29.5
20.7
15.5
11.8
9.1
34.0
29.5
20.7
15.5
11.8
42.9
34.0
29.5
20.7
15.5
54.0
42.9
34.0
29.5
20.7
66.6
54.0
42.9
34.0
29.5
4032
25
20
15
10
5040
32
25
20
15
6550
40
32
25
20
8065
50
40
32
25
100
80
65
50
40
32Nom
inal
Siz
e
DN
NP
S
11 /211 /4 1 3/
4
1/2
3/8
2
11 /2 11 /4 1 3/4
1/2
21 /22 11 /2 11 /4
1
3/4
321 /2 2 11 /2 11 /4 1
43 21 /2 2 11 /2 11 /4
1 2 2 2 2 1 2 2 2 2 1 2 2 2 2 1 2 2 2 2 2 2 2 2 2
Type
3000
6000 1 1 2 2 2 1 2 2 2 2 1 2 2 2 2 1 2 2 2 2 1 2 2 2 2
Layi
ng L
engt
hW
all
Soc
ket B
ore
Dia
.S
hank
Dia
.
B 42.8
34.0
27.3
22.0
17.7
48.9
42.8
34.0
27.3
21.9
61.4
48.9
42.8
34.0
27.3
74.1
61.4
48.9
42.8
34.0
90.0
74.1
61.4
48.9
42.8
12.5
12.5
12.5
9.5
9.5
12.5
12.5
12.5
12.5
9.5
16.0
12.5
12.5
12.5
12.5
16.0
16.0
12.5
12.5
12.5
16.0
16.0
16.0
12.5
12.5
Dep
th o
fS
ocke
t
K m
inS
D
48.3
60.3
73.0
88.9
114.
3
MSS
SP-
79M
SS S
P-79
SW
RED
UCE
R IN
SERT
S
:1)
12
2)S
DB
Not
e:1)
At o
ptio
n of
the
man
ufac
ture
r, ty
pe 2
redu
cers
may
be
furn
ishe
d in
stea
d of
type
1.
2) T
he n
omin
al s
ize
is s
how
ed a
s S
DB
.
SW REDUCER INSERTS
34
6 8 10 15 20 25 32 40 50 65 80 100Nom
inal
Siz
e
DN
NP
S
1/8
1/4
3/8
1/2
3/4
1 11 /4 11 /2 2 21 /2 3 4
21 21 25 28 33 38 44 51 60 76 86 106
Cen
ter-t
o-En
d
2000
6000
GB/
T 14
383
ASM
E B
16.1
1
Out
side
Dia
met
er o
f Ban
dW
all T
hick
ness
Leng
th o
f Thr
ead
3000
6000
2000
3000
2000
6000
3000
6000
2000
3000
AH
G m
inL
5 m
inL
2 m
in90
Elb
ows,
Tee
s, C
ross
es45
Elbo
ws
1)
GB
/T 1
2716
AS
ME
B1.
20.1
NP
TN
ote
1) T
hrea
d sh
all b
e m
achi
ned
per G
B/T
127
16eq
uiva
lent
to A
SM
E B
1.20
.1.
21 25 28 33 38 44 51 60 64 83 95 114
25 28 33 38 44 51 60 64 83 95 106
114
17 17 19 22 25 28 33 35 43 52 64 79
17 19 22 25 28 33 35 43 44 52 64 79
19 22 25 28 33 35 43 44 52 64 79 79
22 22 25 33 38 46 56 62 75 92 109
146
22 25 33 38 46 56 62 75 84 102
121
152
25 33 38 46 56 62 75 84 102
121
146
152
3.18
3.18
3.18
3.18
3.18
3.68
3.89
4.01
4.27
5.61
5.99
6.55
3.18
3.30
3.51
4.09
4.32
4.98
5.28
5.56
7.14
7.65
8.84
11.1
8
6.35
6.60
6.98
8.15
8.53
9.93
10.5
9
11.0
7
12.0
9
15.2
9
16.6
4
18.6
7
6.4
8.1
9.1
10.9
12.7
14.7
17.0
17.8
19.0
23.6
25.9
27.7
6.7
10.2
10.4
13.6
13.9
17.3
18.0
18.4
19.2
28.9
30.5
33.0
Thre
aded
Tee
Thre
aded
Cro
ss90
Thre
aded
90
Elb
ow45
Thre
aded
45
Elb
ow
THREADED FITTINGS
35
6 8 10 15 20 25 32 40 50
Nom
inal
Siz
e
DN
NP
S
1/8
1/4
3/8
1/2
3/4 1 11 /4 11 /2 2
GB/
T 14
383
ASM
E B
16.1
1
:1)
34
90
AH
2)G
B/T
127
16A
SM
E B
1.20
.1N
PT
Not
e:1)
At t
he o
ptio
n of
man
ufac
ture
r,the
siz
es A
and
H o
f thr
eade
d 90
elbo
w in
the
page
of 3
4 ca
n be
appl
ied.
2)Th
read
sha
ll be
mac
hine
d pe
r GB
/T 1
2716
equi
vale
nt to
AS
ME
B1.
20.1
.
19 22 25 28 35 44 51 54 64
Cen
ter t
o Fe
mal
e E
ndS
treet
Ells
3000
6000
Wal
l Thi
ckne
ssLe
ngth
Inte
rnal
Thre
ad
6000
3000
6000
3000
3000
6000
3000
6000
AG
1 m
in
L 5
min
22 25 28 35 44 51 54 64 83
25 32 38 41 48 57 66 71 84
32 38 41 48 57 66 71 84 105
19 25 32 38 44 51 62 70 84
25 32 38 44 51 62 70 84 102
3.18
3.30
3.51
4.09
4.32
4.98
5.28
5.56
7.14
5.08
5.66
6.98
8.15
8.53
9.93
10.5
9
11.0
7
12.0
9
2.74
3.22
3.50
4.16
4.88
5.56
5.56
6.25
7.64
4.22
5.28
5.59
6.53
6.86
7.95
8.48
8.89
9.70
JH
G2
min
L m
in
6.4
8.1
9.1
10.9
12.7
14.7
17.0
17.8
19.0
6.7
10.2
10.4
13.6
13.9
17.3
18.0
18.4
19.2
10 11 13 14 16 19 21 21 22
Leng
th M
ale
Thre
ad
L 2
min
Wal
l Thi
ckne
ssC
ente
r to
Mal
e E
ndS
treet
Ells
Out
side
Dia
met
er o
f End
90Fe
mal
e an
d M
ale
Thre
aded
90
Elb
ow
THREADED FITTINGS
36
GB/
T 14
383
ASM
E B
16.1
1
:1)
G
B/T
127
16A
SM
E B
1.20
.1N
PT
Not
e:1)
Thr
ead
shal
l be
mac
hine
d pe
r GB
/T 1
2716
equi
vale
nt to
AS
ME
B1.
20.1
.
G m
in
32 35 38 48 51 60 67 79 86 92 108
121
End-
to-E
nd
3000
& 6
000
3000
Leng
th o
f Thr
ead
3000
6000
3000
6000
6000
L 5
min
L 2
min
W
19 25 25 32 37 41 44 44 48 60 65 68
- 27 27 33 38 43 46 48 51 64 68 75
16 19 22 28 35 44 57 64 76 92 108
140
22 25 32 38 44 57 64 76 92 108
127
159
4.8
4.8
4.8
6.4
6.4
9.7
9.7
11.2
12.7
15.7
19.0
22.4
- 6.4
6.4
7.9
7.9
11.2
11.2
12.7
15.7
19.0
22.4
28.4
6.4
8.1
9.1
10.9
12.7
14.7
17.0
17.8
19.0
23.6
25.9
27.7
6.7
10.2
10.4
13.6
13.9
17.3
18.0
18.4
19.2
28.9
30.5
33.0
P
End-
to-E
ndEn
d W
all
6 8 10 15 20 25 32 40 50 65 80 100
Nom
inal
Siz
e
DN
NP
S
1/8
1/4
3/8
1/2
3/4
1 11 /4 11 /2 2 21 /2 3 4
D
Out
side
Dia
met
er
Hal
f-Cou
plin
gC
apC
oupl
ing
THREADED FITTINGS
Bos
s
37
GB/
T 14
383
ASM
E B
16.1
1
:1)
G
B/T
127
16A
SM
E B
1.20
.1N
PT
Not
e:1)
Thr
ead
shal
l be
mac
hine
d pe
r GB
/T 1
2716
equi
vale
nt to
AS
ME
B1.
20.1
.
6 8 10 15 20 25 32 40 50 65 80 100
Nom
inal
Siz
e
DN
NP
S
1/8
1/4
3/8
1/2
3/4
1 11 /4 11 /2 2 21 /2 3 4
Leng
thSq
uare
Hei
ght
Wid
th F
lats
Hea
d D
iam
eter
Leng
thH
ex H
eigh
tH
ex H
eigh
t
A m
inB
min
C m
inE
nom
D m
inH
min
Gm
in
10 11 13 14 16 19 21 21 22 27 28 32
6 6 8 10 11 13 14 16 18 19 21 25
7 10 11 14 16 21 24 28 32 36 41 65
10 14 18 21 27 33 43 48 60 73 89 114
35 41 41 44 44 51 51 51 64 70 70 76
6 6 8 8 10 10 14 16 18 19 21 25
- 3 4 5 6 6 7 8 9 10 10 13
Hex
Wid
th F
lats
F nom
11 16 18 22 27 36 46 50 65 75 90 115
Squa
re H
ead
Plug
Hex
Hea
d Pl
ugH
ex H
ead
Bus
hing
Flus
h B
ushi
ngR
ound
Hea
d Pl
ug
THREADED FITTINGS
38
3000Class 3000 Unions of SW Ends
PipeEnd
MSS SP-83
:1) H 4
ASME B1.1 2A/2B
Note:1) H is the number of threads per inch with the min. of 4 tighting turns,
and the female and male thread herein shall be machined per ASMEB1.1 2A/2B.
Nominal Size
DN
6
8
10
15
20
25
32
40
50
65
80
NPS
SocketBore Dia.
SocketWall
WaterWay Bore
LayingLength
MaleFlange
NutTHRD Per
InchBearing Depth of
SocketLengthAssem
Clear Assem.Nut
A min B C min D E Fmin G min H J min K min L nom N
1/8
1/4
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
21.8
21.8
25.9
31.2
37.1
45.5
54.9
61.5
75.2
91.7
109.2
10.9
14.3
17.7
21.9
27.3
34.0
42.8
48.9
61.2
73.9
89.9
3.2
3.3
3.5
4.1
4.3
5.0
5.3
5.5
6.0
7.7
8.3
6.1
8.5
11.8
15.0
20.2
25.9
34.3
40.1
51.7
61.2
76.4
20.7
20.7
23.8
23.8
28.6
30.2
36.6
38.1
41.4
56.9
58.7
3.2
3.2
3.4
3.7
4.1
4.6
5.3
5.8
6.6
7.5
8.3
3.2
3.2
3.4
3.7
4.1
4.4
5.2
5.6
6.4
7.1
8.0
16
16
14
14
11
11
10
10
10
8
8
1.2
1.2
1.4
1.5
1.7
1.9
2.1
2.3
2.7
3.1
3.5
9.7
9.7
9.7
9.7
12.7
12.7
12.7
12.7
15.7
15.7
15.7
41.4
41.4
46.0
49.0
56.9
62.0
71.1
76.5
86.1
102.4
109.0
51
51
56
59
66
79
94
112
132
150
176
UNIONS
39
MSS SP-83
:1 ) H 4
ASME B1.1 2A/2B2) GB/T 12716 ASME B1.20.1 NPT
Note:1) H is the number of threads per inch with the min. of 4 tighting turns, and
the female and male thread herein shall be machined per ASME B1.12A/2B.
2) Thread shall be machined per GB/T 12716 equivalent to ASME B1.20.1 .
Pipe EndNominal Size
DN
6
8
10
15
20
25
32
40
50
65
80
NPS
Wall Bore Male Flange Nut THRD Per Inch
BearingLengthAssem
Clear Assem.Nut
A min C min D F min G min H J min L nom N
1/8
1/4
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
14.7
19.1
22.9
27.7
33.5
41.4
50.5
57.2
70.1
85.3
102.4
2.4
3.0
3.2
3.7
3.9
4.5
4.9
5.1
5.5
7.0
7.6
8.46.411.19.4
14.313.517.917.123.021.429.027.737.735.443.541.255.652.166.364.382.677.3
3.2
3.2
3.4
3.7
4.1
4.6
5.3
5.8
6.6
7.5
8.3
3.2
3.2
3.4
3.7
4.1
4.4
5.2
5.6
6.4
7.1
8.0
16
16
14
14
11
11
10
10
10
8
8
1.2
1.2
1.4
1.5
1.7
1.9
2.1
2.3
2.7
3.1
3.5
41.4
41.4
46.0
49.0
56.9
62.0
71.1
76.5
86.1
102.4
109.0
51
51
56
59
66
79
94
112
132
150
176
3000Class 3000 Unions of THRD Ends
UNIONS
40
TOLERANCES FOR THRD FITTINGS
Nominal Size
Elbows,Tees & Crosses Couplings Half- couplings
Center-to-End End-to-End End-to-End
6 8
10 20
25 50
65 100
1/8 1/4
3/8 3/4
1 2
21/2 4
1.0
1.5
2.0
2.5
1.0
1.5
2.0
2.5
1.0
1.5
2.0
2.5
DN NPS A J W W/ 2
CLASS OF THE FITTINGS VS THE GRADE OF THE CONNNECTING PIPES
1)Note1) In this table, it isn t restricted to use the pipes with thinner or thicker
thickness than the connecting fittings. The actually used pipes can bethinner or thicker than the ones indicated in the table. When usingthicker pipes,the fittings shall govern the pressure bearing; when usingthinner pipes, the pipes shall govern the pressure bearing.
Joint Type Class Grade of Connecting Pipes Joint Type Class Grade of Connecting Pipes
SW THRD
3000
6000
9000
Sch80 XS
Sch160
XXS
2000
3000
6000
Sch80 XS
Sch160
XXS
TOLERANCES FOR SW FITTINGS
SocketBore Dia.
Nominal Size
DN
6 8
10 20
25 40
50
65 80
100
NPS
Bore Dia. ofFittings
Center toBottom of
Socket
LayingLengths
LayingLengths
LayingLength
Shank Dia.Length
LayingLength
B D A H E F A SD SL E
All FittingsElbows,Tees &
CrossesCouplings
Half-Couplings
Reducer Inserts Unions
1/8 1/4
3/8 3/4
1 11/2
2
21/2 3
4
+0.40
+0.40
+0.40
+0.50
+0.50
+0.50
+1.50
+1.50
+1.50
+1.50
+3.00
+3.00
1.0
1.5
2.0
2.0
2.5
2.5
1.5
3.0
4.0
4.0
5.0
5.0
1.0
1.5
2.0
2.0
2.5
2.5
1.5
3.0
4.0
4.0
5.0
-
+1.50
+1.50
+2.00
+2.00
+2.50
+2.50
0.25
0.25
0.25
0.5
0.5
0.7
0-1.5
0-1.5
0-2.0
0-2.0
0-2.5
0-2.5
TOLERANCES FOR SW/THRD FITTINGS
41
1)
2)
3)
Note1 For products with two ends such as reducing elbows, couplings, re-
ducer inserts,unions and etc,the size of the large end shall be givenfirst, followed by the size of the small end.
2 For the products with three ends such as reducing tees and etc., thesize of the largest run opening shall be given fist followed by the sizeof the opposite end of the run and the size of the outlet is given last.
3 For reducing crosses, the size of the largest run opening shall be givefirst, followed by the size of the opposite end of the run, the largestside-outlet opening is the third given followed by the opposite opening.
SYMBOLS OF NORMINAL SIZE OF REDUCING FITTINGS
Sch160NOMINAL WALL THICKNESS OF SCHEDULE 160 AND DOUBLE EXTRA STRONG PIPE
Nominal Size Nominal Wall Tickness
6
8
10
DN NPS Sch160 XXS
1/8
1/4
3/8
3.15
3.68
4.01
4.83
6.05
6.40
1 ASME B36.10M Sch160 XXSNote1) Since ASME B36.10M doesn t include the thickness for Sch160 nor
XXS, The values indicated in the table may be used as the nominal wallthickness of pipe.
1 1 1
3/411/211/2
22 1
22 1 11/2
22 1 11/2 3/4
END TYPES OF SWAGED NIPPLES1) (BE PE
( T E ) ( )a) BBEb) PBEc) TBEd) / BLE/PSEe) / BLE/TSEf) / PLE/BSEg) / PLE/TSEh) / TLE/BSEi) / TLE/PSEj) / (BSE/PLE)k) / (BSE/TLE)l) / (PSE/BLE)m) / (PSE/TLE)n) / (TSE/BLE)o) / (TSE/PLE)
2) 21 GB/T 12716 ASMEB1.20.1 NPT
1) The end types of swaged nipples include bevel end(BE) plain end(PE) thread end(TE) and other types, the following indicates thecommon:
a) bevel of both ends (BBE)b) plain of both ends (PBE)c) thread of both ends (TBE)d) bevel of large end/plain of small end (BLE/PSE)e) bevel of large end/thread of small end (BLE/TSE)f) plain of large end/bevel of small end (PLE/BSE)g) plain of large end/thread of small end (PLE/TSE)h) thread of large end/bevel of small end (TLE/BSE)i) bevel of large end/plain of small end (TLE/PSE)j) bevel of small end/plain of large end (BSE/PLE)k) bevel of small end/thread of large end (BSE/TLE)l) plain of small end/bevel of large end (PSE/BLE)m) plain of small end/ thread of large end (PSE/TLE)n) thread of small end/ bevel of large end (TSE/BLE)o) thread of small end/ plain of large end (TSE/PLE)
2) Refer the drawings in the page of 21for the bevelend.Thread shall bemachined per GB/T 12716 equivalent to ASME B1.20.1 .
OTHER
42
Concentric Swaged Nipple Eccentric Swaged Nipple
65 665 865 1065 1565 2065 2565 3265 4065 5080 680 880 1080 1580 2080 2580 3280 4080 5080 6590 690 890 1090 1590 2090 2590 3290 4090 5090 6590 80100 8100 10100 15100 20100 25100 32
MSS SP-95 SH/T 3419
Nominal Size
8 610 610 815 615 815 1020 620 820 1020 1525 625 825 1025 1525 2032 632 832 1032 1532 2032 2540 640 840 1040 1540 2040 2540 3250 650 850 1050 1550 2050 2550 3250 40
DN
OD at End Length ofSmall End End to End
NPS OD1 OD2 SL min A
1/4 1/83/8 1/83/8 1/41/2 1/81/2 1/41/2 3/83/4 1/83/4 1/43/4 3/83/4 1/21 1/81 1/41 3/81 1/21 3/411/4 1/811/4 1/411/4 3/811/4 1/211/4 3/411/4 111/2 1/811/2 1/411/2 3/811/2 1/211/2 3/411/2 111/2 11/4
2 1/82 1/42 3/82 1/22 3/42 12 11/4
2 11/2
13.7 10.317.1 10.317.1 13.721.3 10.321.3 13.721.3 17.126.7 10.326.7 13.726.7 17.126.7 21.333.4 10.333.4 13.733.4 17.133.4 21.333.4 26.742.2 10.342.2 13.742.2 17.142.2 21.342.2 26.742.2 33.448.3 10.348.3 13.748.3 17.148.3 21.348.3 26.748.3 33.448.3 42.260.3 10.360.3 13.760.3 17.160.3 21.360.3 26.760.3 33.460.3 42.260.3 48.3
202020202020202022222020222222202022222525202022252525252022222530303030
57
64
70
76
89
102
114
165
Nominal Size
DN
OD at End Length ofSmall End End to End
NPS OD1 OD2 SL min A
21/2 1/821/2 1/421/2 3/821/2 1/221/2 3/421/2 121/2 11/4
21/2 11/2
21/2 23 1/83 1/43 3/83 1/23 3/43 13 11/4
3 11/2
3 23 21/2
31/2 1/831/2 1/431/2 3/831/2 1/231/2 3/431/2 131/2 11/4
31/2 11/2
31/2 231/2 21/2
31/2 34 1/44 3/84 1/24 3/44 14 11/4
73.0 10.373.0 13.773.0 17.173.0 21.373.0 26.773.0 33.473.0 42.273.0 48.373.0 60.388.9 10.388.9 13.788.9 17.188.9 21.388.9 26.788.9 33.488.9 42.288.9 48.388.9 60.388.9 73.0101.6 10.3101.6 13.7101.6 17.1101.6 21.3101.6 26.7101.6 33.4101.6 42.2101.6 48.3101.6 60.3101.6 73.0101.6 88.9114.3 13.7114.3 17.1114.3 21.3114.3 26.7114.3 33.4114.3 42.2
222222252530304040222222252530304040402222222525303040404040252525303040
178
203
203
229
SWAGED NIPPLES
43
200 25200 32200 40200 50200 65200 80200 90200 100200 125200 150250 50250 65250 80250 90250 100250 125250 150250 200300 50300 65300 80300 90300 100300 125300 150300 200300 250
SWAGED NIPPLES
Nominal Size
100 40100 50100 65100 80100 90125 8125 10125 15125 20125 25125 32125 40125 50125 65125 80125 90125 100150 15150 20150 25150 32150 40150 50150 65150 80150 90150 100150 125
DN
OD at End Length ofSmall End End to End
NPS OD1 OD2 SL min A
4 11/2
4 24 21/2
4 34 31/2
5 1/45 3/85 1/25 3/45 15 11/4
5 11/2
5 25 21/2
5 35 31/2
5 46 1/26 3/46 16 11/4
6 11/2
6 26 21/2
6 36 31/2
6 46 5
114.3 48.3114.3 60.3114.3 73.0114.3 88.9114.3 101.6141.3 13.7141.3 17.1141.3 21.3141.3 26.7141.3 33.4141.3 42.2141.3 48.3141.3 60.3141.3 73.0141.3 88.9141.3 101.6141.3 114.3168.3 21.3168.3 26.7168.3 33.4168.3 42.2168.3 48.3168.3 60.3168.3 73.0168.3 88.9168.3 101.6168.3 114.3168.3 141.3
40454545452525253030404045454545503030404045454545505060
229
279
304
Nominal Size
DN
OD at End Length ofSmall End End to End
NPS OD1 OD2 SL min A
8 18 11/4
8 11/2
8 28 21/2
8 38 31/2
8 48 58 610 210 21/2
10 310 31/2
10 410 510 610 812 212 21/2
12 312 31/2
12 412 512 612 812 10
219.1 33.4219.1 42.2219.1 48.3219.1 60.3219.1 73.0219.1 88.9219.1 101.6219.1 114.3219.1 141.3219.1 168.3273.0 60.3273.0 73.0273.0 88.9273.0 101.6273.0 114.3273.0 141.3273.0 168.3273.0 219.1323.8 60.3323.8 73.0323.8 88.9323.8 101.6323.8 114.3323.8 141.3323.8 168.3323.8 219.1323.8 273.0
404045454550505060604545505060606565505060606565657070
330
381
406
1 SH/T 3419 SH/T 3405Note1) If ordering per SH/T 3419,the outside diameter specified in SH/T 3405
tube outside diameter in petrochemical industry shall be applied.
TOLERANCES OF SWAGED NIPPLES
Nominal Size OD at End ID at End End to End Wall
DN NPSOD
ID A T
6 10
15 40
50 65
80 100
125 150
200 300
1/8 3/8
1/2 11/2
2 21/2
3 4
5 6
8 12
0.40.80.40.8
0.8
0.8
2.41.64.03.2
0.8
1.60.81.60.8
1.6
2.41.64.03.2
0.8
0.8
0.8
1.6
1.6
3.2
1.6
1.6
3.2
3.2
4.8
6.4
87.5%Not less than
87.5%Nominal WallThickness
Plain End Other Ends
SWAGED NIPPLES
44
688 61010 81515 1015 82020 1520 102525 2025 153232 2532 2032 154040 3240 2540 2040 155050 4050 3250 2550 2050 156565 5065 4065 3265 2565 208080 6580 5080 4080 3280 25
SizeNominal Size
DND
Reducing Hexagonal Nipple
NPS
straight Hexagonal Nipple
:1) GB/T 12716 ASME B1.20.1 NPT
Note:1) Thread shall be machined per GB/T 12716 equivalent to ASME B1.20.1 .
C nom E 1 nom E 2 nom WSch80 Sch160
1/81/41/4 1/83/83/8 1/41/21/2 3/81/2 1/43/43/4 1/23/4 3/811 3/41 1/211/411/4 111/4 3/411/4 1/211/211/2 11/4
11/2 111/2 3/411/2 1/222 11/2
2 11/4
2 12 3/42 1/221/221/2 221/2 11/2
21/2 11/4
21/2 121/2 3/433 21/2
3 23 11/2
3 11/4
3 1
66688888101010101010121212121616161616181818181818202020202020202020202020
1015151616202020212121252525252525252626262626272727272727383838383838404040404040
--
10-
15-
1615-
2016-
2120-
252120-
25252120-
2625252120-
2726252521-
3827262525
26363140394844435251476056556262585768676763627271707066659685848383791009887868585
57510713107181310231813312318133631231813473631231813574736312318705747363123
46486108614108191410281914103228191410403228191410514032281914635140322819
HEXAGDNAL NIPPLES
45
Pipe Nipple(TBE)Pipe Nipple(TOE)ASTM A733
1)
2) GB/T 12716 ASME B1.20.1 NPT
Note1) The lengths indicated in the above table are the generally referenced ones.
Manufacturer shall conform to the ones specified in the purchasespecification. If not specified, manufacturer can select one of the abovethree series.
2) Thread shall be machined per GB/T 12716 equivalent to ASME B1.20.1 .
6810152025324050658090100125150200250300
OD of PipesNominal Size
DN NPS OD L 2 min T
1/81/43/81/23/4111/411/2221/2331/245681012
10.313.717.121.326.733.442.248.360.373.088.9101.6114.3141.3168.3219.1273.0323.8
6.710.210.413.613.917.318.018.419.228.930.531.833.035.738.443.548.954.0
STD, XS
Sch40,Sch80
STD, XS
Sch40,Sch80
STD, XS
Sch40,Sch80
STD, XS
Sch40,Sch80
STD, XS
Sch40,Sch80
STD, XS
Sch40,Sch80
Pipe Nipple Lengths.
L
50
50
75
100
100
150
Lengths of Thread Wall of pipes
75
75
100
150
150
200
100
100
150
200
200
250
TOLERANCES OF HEXAGONAL NIPPLES & PIPE NIPPLES
Note1 L 305mm 12 3.2mm
Note1) If the length L of the thread nipple is more than and including 305mm
12 , the tolerance shall be 3.2mm.
PIPE NIPPLES
Nominal Size
DN
Hexagonal Nipple Pipe Nipple
NPS w D L
6 20
25 80
90 300
1/8 3/4
1 3
31/2 12
1.6
1.6
-
00.801.6
-
1.6
1.6
1.6
46
SW Outlets
BranchNominal Size
GB/T 19326 MSS SP-97
1 B D 3 0Note1) As for the sizes of socket diameter B and bore D, please refer to the
ones in the page of 30.
Depth ofSocket
Face of Fitting toCrotch
OD of FittingSocket WallThickness
Cut Hole Dia.
DN NPS J min 3000 6000 3000 6000 3000 6000 3000 6000
6
8
10
15
20
25
32
40
50
65
80
100
1/8
1/4
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
4
9.5
9.5
9.5
9.5
12.5
12.5
12.5
12.5
16.0
16.0
16.0
19.0
10
10
13
16
16
22
22
24
24
25
30
30
-
-
-
24
25
29
30
32
37
-
-
-
27
27
30
38
47
56
66
75
90
105
124
154
-
-
-
47
53
63
74
83
104
-
-
-
3.18
3.78
4.01
4.67
4.90
5.69
6.07
6.35
6.93
8.76
9.52
10.69
-
-
-
5.97
6.96
7.92
7.92
8.92
10.92
-
-
-
16
16
19
24
30
36
45
51
65
76
94
121
-
-
-
19
25
33
38
49
59
-
-
-
Nominal Size
DN
8 900
10 900
15 900
20 900
25 900
32 900
40 900
50 900
65 900
80 900
100 900
125 900
NPS
1/4 36
3/8 36
1/2 36
3/4 36
1 36
11/4 36
11/2 36
2 36
21/2 36
3 36
4 36
5 36
A max D 1 min C min d 1 nom
OUTLETS
47
BranchNominal Size
GB/T 19326 MSS SP-97
1 GB/T 12716 ASME B1.20.1 NPTNote1) Thread shall be machined per GB/T 12716 equivalent to ASME B1.20.1 .
Length OD of Fitting OD at End of Branch Cut Hole Dia.
DN NPS3000 6000 3000 6000 3000 6000 3000 6000
6
8
10
15
20
25
32
40
50
65
80
100
1/8
1/4
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
4
19
19
21
25
27
33
33
35
38
46
51
57
32
37
40
41
43
52
27
27
30
38
47
56
66
75
90
105
124
154
45
52
63
72
83
104
22
22
25
33
39
48
58
64
77
94
114
140
42
48
58
67
77
93
16
16
19
24
30
36
45
51
65
76
94
121
19
25
33
38
49
59
Run PipesNominal Size
DN
8 900
10 900
15 900
20 900
25 900
32 900
40 900
50 900
65 900
80 900
100 900
125 900
NPS
1/4 36
3/8 36
1/2 36
3/4 36
1 36
11/4 36
11/2 36
2 36
21/2 36
3 36
4 36
5 36
A D 1 min D 2 min d 1 nom
Length ofThread
L2 min
6.7
10.2
10.4
13.6
13.9
17.3
18.0
18.4
19.2
28.9
30.5
33.0
THRD Outlet
OUTLETS
48
BW Outlet
BranchNominal Size
GB/T 19326 MSS SP-97
1) D 2 d 4 T
2) 2 1
Note1) D2 is same to the outside diameter of branch pipe, d 4is same to the
inside diameter of branch pipe, T is same to the wall thickness ofbranch pipe.
2) As fo the bevel ends of the branch pipe, please refers to the figure inthe page of 21.
Length OD of Fitting Cut Hole Dia.
DN NPSSTD XS Sch160 STD XS SCH160 SCH160
Run PipesNominal Size
DN
8 90010 90015 90020 90025 90032 90040 90050 90065 90080 90090 900
100 900125 900150 900200 900250 900300 900350 900400 900450 900500 900550 900650 900
NPSA D 2 min d 1 nom
STD XS1/4 363/8 361/2 363/4 361 36
11/4 3611/2 362 36
21/2 363 36
31/2 364 365 366 368 36
10 3612 3614 3616 3618 3620 3622 3626 36
68
10152025324050658090
100125150200250300350400450500600
1/81/43/81/23/41
11/411/22
21/23
31/24568
10121416182024
161619192227323338414448515760707886899497
102116
1616191922273233384144485157789994
103100106111119140
2832384451556273
8494
105
242630364355667490
104124138154187213265323379411465522573690
242630364355667490
104124138154187227292325381416468525584708
36465163718298
122
154188222
1616192430364551657693113120141170220275325357408459508614
1616192430364551657693113120141170220265317351403455509612
1419253338435473
98122146
OUTLETS
49
BranchNominal Size
45ELBOLETS AND LATROLETS
:1 46 48
Note1) As for other sizes, please refer to the ones in the page of 46 48.
Cut Hole Dia.
DN NPS
Run PipesNominal Size
DN
20 90025 90032 90040 90050 90065 90080 90090 900
125 900200 900250 900300 900350 900
NPS
d 1 nom
3/4 361 36
11/4 3611/2 362 36
21/2 363 36
31/2 365 368 36
10 3612 3614 36
1520253240506580
100150200250300
1/23/41
11/411/22
21/23468
1012
Length
STD XS Sch160 3000 6000 STD XS Sch160
A
3000 600045506068759095
120140195220270290
505870768398
105130150210
---
455060687590-------
505870768398-------
314254617690
100132168238338432498
30405058668395115150225
---
314254617690-------
304050586683-------
BW SW and THRD BW SW and THRD
BW Elbolet SW Elbolet THRD Elbolet
45BW Latrolet
45SW Latrolet
45THRD Latrolet
OUTLETS
50
NIPOLETS
1)2) D2 DN15 40 NPS1/2 11/2 0.25mm, DN50
100(NPS2 4) 0.5mm; T XS Sch160 , d2= D2-2T
3)GB/T 12716 ASME B1.20.1 NPT
4) A 114mm 140mm 165mm
Note1) This nipolet is used to connect the valve at the the end of the branch pipe.2) The tolerance of D2 shall be as: DN15 40 NPS1/2 11/2 : 0.25mm,
DN50 100(NPS2 4): 0.5mm.T is the thickness of XS or Sch160, d1 = D2-2T
3) Per the purchase specification, the ends can be machined as plain or threadedtype, and the thread shall be machined per GB/T 12716 equivalent to ASMEB1.20.1
4) Per the purchase specification, the size of A can be machined as 114mm140mm and 165mm.
BranchNominal Size
OD at End Cut Hole Dia.
DN NPS A D2 XS Sch160 XS Sch160
Run PipesNominal Size
DN
20 90025 90032 90040 90050 90065 90080 90090 900
125 900
NPSD1 min d 1 nom
3/4 361 36
11/4 3611/2 362 36
21/2 363 36
31/2 365 36
1520253240506580
100
1/23/41
11/411/22
21/234
89
89
89
21.326.733.442.248.360.373.088.9114.3
384756667590
105124154
4753637283
104
2430364551657694
121
192533384959
OD of FittingLength
PE TE
NIPOLETS
51
BW Pipet SW Pipet
Branch Nominal Size
DN
68
10152025324050658090
100125150200250300350400450500600750
NPSA
Sch5s Sch10s
d 1 nom
1/81/43/81/23/41
11/411/22
21/23
31/24568
1012141618202430
161619192227323338424548515760707886899497
102116137
---
2627333335384651-
57-----------
---
18.023.430.138.945.057.068.884.797.4110.1135.8162.8213.6266.2315.9347.7398.8448.6498.4598.9749.3
7.810.413.817.122.527.936.742.854.866.982.895.5
108.2134.5161.5211.6264.6314.7346.0396.8447.4496.9597.3746.2
Cut Hole Dia.Length
PIPETS
1) Sch5s Sch10s2) O D 2 1
Note1) The pipets are usually used for connection when the schedule of the run pipe is
Sch5s or Sch10s.2) OD is the outside diameter of the connecting branch pipe. As for the bevel
ends, please refer the figure in page of 21.
Run Pipes Nominal Size
DN
8 90010 90015 90020 90025 90032 90040 90050 90065 90080 90090 900
100 900125 900150 900200 900250 900300 900350 900400 900450 900500 900550 900650 900800 900
NPS
1/4 363/8 361/2 363/4 361 36
11/4 3611/2 362 36
21/2 363 36
31/2 364 365 366 368 36
10 3612 3614 3616 3618 3620 3622 3626 3632 36
BW SW
PIPETS
52
CLASS OF OUTLETS VS SCHEDULE OF THE CONNECTING RUN PIPE
Branch Nominal Size
1)Note1) When the schedule of branch or running pipe is out of the scope indicated in the above
table, the outlet can be fabricated with special thickness,size and configuration on thebasis of the agreement between purchaser and manufacturer.
DN NPSType Class of Outlet
Schedule of the ConnectingRun Pipe
6 100
15 50
6 600
6 600
15 150
1/8 4
1/2 2
1/8 24
1/8 24
1/2 6
Socket Welding & Threaded
Socket Welding & Threaded
Buttwelding
Buttwelding
Buttwelding
3000
6000
STD
XS
SCH160
XS
SCH160
STD
XS
SCH160
d 4
BW Outlet
TOLERANCES OF OUTLETS
The following figures show the allowable spacing tolerances between outlet and the running pipe:
Outlet of THRD & BW
A B D2
SW OutletBranch Nominal Size
DN
6 20
25 100
125 300
350 600
NPS D
1/8 3/4
1 4
5 12
14 24
0.8
1.6
3.2
4.8
0.500.50-
-
1.501.50-
-
0.80.40.80.41.60.81.60.8
0.4
0.4
0.8
0.8
TOLERANCES OF OUTLETS
53
Threaded Welding Neck Slip-on Welding
Socket Welding Blind Lapped
Flanges
Item
Content
GB/T 9112 GB/T 9124SH 3406HG 20592 HG 20605, HG 20615 HG 20626ASME B16.5ASME B16.47
or according to the client s standards or technical requirements
Standard
Material, ,
Carbon steel, alloy steel and stainless steel
SizeDN15 DN2000NPS 1/2 NPS 80
Class
(European system):PN0.25MPa, PN0.6MPa, PN1.0MPa, PN1.6MPa, PN2.5MPa, PN4.0MPa, PN6.3MPa, PN10.0MPa, PN16.0MPa
(American system):PN2.0MPa, PN5.0MPa, PN11.0MPa, PN15 .0MPa, PN26.0MPa, PN42.0MPa /Class 150, Class 300, Class 400, Class 600, Class 900, Class 1500, Class 2500
Contact Surface
Type of contacet surface
flat face
male and female
tongue and groove
ring joint face
raised face
Symbol
FF
RF
MF
TG
RJ
FLANGES
54
Stan
dard
Old
Gra
de
Che
mic
al C
ompo
sitio
n %
, max
Mec
hani
cal R
equi
rem
ent
CS
iM
nP
SC
rN
iM
oO
ther
T.S
.m
inM
Pa
Y.S
.m
inM
Pa
0.17
-0.2
30.
17-0
.37
0.35
-0.6
50.
035
0.03
50.
250.
30-
Cu:
0.25
410
245
2515
6Z
55%
0.17
-0.2
40.
17-0
.37
0.35
-0.6
50.
035
0.04
00.
250.
25-
Cu:
0.25
410
-28
--
0.20
0.35
0.50
-1.0
00.
025
0.01
50.
300.
300.
080
Alt
0.02
0;C
u:0.
3040
0-52
024
525
-A
KV
31J
0.20
0.55
1.20
-1.6
00.
025
0.01
50.
300.
300.
080
Alt
0.02
0;C
u:0.
3051
0-64
034
521
-A
KV
34J
0.12
-0.1
80.
15-0
.40
0.40
-0.7
00.
025
0.01
00.
80-1
.20
0.30
0.45
-0.6
0C
u:0.
3045
0-59
029
519
-A
KV
31J
0.08
-0.1
50.
15-0
.40
0.40
-0.7
00.
025
0.01
00.
90-1
.20
0.30
0.25
-0.3
5V
:0.1
5-0.
30;C
u:0.
3044
0-59
024
519
-A
KV
34J
0.12
-0.1
80.
17-0
.37
0.40
-0.7
00.
035
0.03
50.
80-1
.10
0.30
0.40
-0.5
5C
u:0.
3044
029
522
179
Z60
%;
AK
U2
94J
0.08
-0.1
50.
17-0
.37
0.40
-0.7
00.
035
0.03
50.
90-1
.20
0.30
0.25
-0.3
5V
:0.1
5-0.
30;C
u:0.
3049
024
522
179
Z50
%;
AK
U2
71J
0.17
-0.2
30.
17-0
.37
0.35
-0.6
50.
035
0.03
50.
250.
30-
Cu:
0.25
410-
550
245
20-
-0.
220.
351.
400.
045
0.05
00.
300.
30-
Cu:
0.30
;N:0
.008
370-
500
235
26-
-0.
200.
351.
400.
045
0.04
50.
300.
30-
Cu:
0.30
;N:0
.008
370-
500
235
26-
AK
V27
J0.
240.
351.
500.
045
0.05
00.
300.
30-
Cu:
0.30
;N:0
.008
410-
540
275
22-
-0.
210.
351.
500.
045
0.04
50.
300.
30-
Cu:
0.30
;N:0
.008
410-
540
275
22-
AK
V27
J
0.20
0.15
-0.5
01.
20-1
.60
0.02
50.
012
0.25
0.40
0.08
Cu:
0.25
;Als
0.02
049
0-62
031
521
-kv
234
J(-
40)
0.12
0.15
-0.5
01.
20-1
.60
0.02
00.
012
0.25
0.30
-0.8
00.
08C
u:0.
25;N
b:0.
04,
kv2
34J
Als
0.02
044
0-57
030
023
-(-
70)
0.17
-0.2
40.
17-0
.37
0.35
-0.6
50.
030
0.03
00.
250.
250.
15C
u:0.
20;V
:0.0
841
0-55
024
524
-A
KV
35J
0.12
-0.1
80.
17-0
.37
0.40
-0.7
00.
030
0.03
00.
80-1
.10
-0.
40-0
.55
-44
0-64
023
521
-A
KV
35J
0.08
-0.1
50.
17-0
.37
0.40
-0.7
00.
030
0.03
00.
90-1
.20
-0.
25-0
.35
V:0
.15-
0.30
470-
640
255
21-
AK
V35
J0.
210.
350.
40-1
.20
0.03
50.
035
0.25
0.30
0.10
Cu:
0.30
410-
530
235
22-
-0.
220.
350.
80-1
.40
0.03
50.
035
0.25
0.30
0.10
Cu:
0.30
460-
580
265
21-
-0.
230.
350.
80-1
.50
0.03
50.
035
0.25
0.30
0.10
Cu:
0.30
490-
610
285
21-
-0.
17-0
.24
0.17
-0.3
70.
35-0
.65
0.03
00.
030
0.25
0.25
0.15
Cu:
0.20
;V:0
.08
410-
550
245
24-
AK
U2
39J
0.12
-0.2
00.
20-0
.60
1.20
-1.6
00.
030
0.03
00.
300.
30-
Cu:
0.20
490-
670
320
21-
AK
U2
47J/
AKV
21J(-
40)
0.12
-0.1
80.
17-0
.37
0.40
-0.7
00.
030
0.03
00.
80-1
.10
0.30
0.40
-0.5
5C
u:0.
2044
0-64
023
521
-A
KU
247
J0.
150.
500.
600.
030
0.03
04.
00-6
.00
0.60
0.45
-0.6
0C
u:0.
2039
0-59
019
522
AK
U2
94J
NO
TE:
1)Th
e m
echa
nica
l pro
perti
es m
ay v
ary
beca
use
of th
e di
ffere
nt th
ickn
ess,
See
the
stan
dard
s.2)
The
sum
of C
r, N
i,Cu
and
Mo
shal
l not
exc
eed
0.70
%.
3)Th
e m
icro
elem
ents
of N
b,V
and
Ti c
an b
e ad
ded
in Q
245R
Q34
5R a
nd th
e co
nten
t sha
ll no
t exc
eed
0.05
0%0.
10%
0.12
% a
ccor
ding
ly.
4)W
hen
the
mic
roel
emen
ts N
b, V
&T
are
adde
d in
ste
el,th
e lo
wer
lim
itatio
n of
Alt
dose
nt a
pply
.5)
Whe
n th
e th
ickn
ess
exce
eds
1640
mm
,the
yie
ld s
treng
th c
an b
e re
duce
d by
10M
Pa
20-
20-
Q245
R 2)3)
4)20
g,20
RQ3
45R 2)
3)4)
16M
ng,1
6MnR
15Cr
MoR
15Cr
Mog,1
5CrM
oR12
Cr1M
oVR
12Cr
1MoV
g
15Cr
Mo
-
12Cr
1MoV
-
20 1)
-Q
235A
-Q
235B
-Q
275A
-Q
275B
-
16M
nDR
-
09M
nNiD
R-
20G
-15
CrM
oG-
12Cr
1MoV
G-
410
-46
0-
490
-20
-
16M
n-
15Cr
Mo
-1C
r5M
o-
GB/T
699
EL
.m
in %
HB
max
Oth
er
TH
E G
EN
ER
AL
ME
TA
LLIC
MA
TE
RIA
LS O
F C
HIN
ES
E P
RE
SS
UR
E P
IPIN
G C
OD
E
New
Gra
de
GB/T
711
GB/T
7131)
GB/T
3077
GB/T
3087
GB/T
3274
1)
(GB/T
700
)
GB 35
31 1)
GB53
10
GB/T5
3122)
GB 64
79 5)
1) 2)C
rN
iC
uM
o0.
70%
3)Q
245R
Q34
5RN
bV
Ti
30.
050%
0.10
%0.
12%
4)N
bV
Ti
Alt
5)16
40m
m10
MP
a
THE GENERAL MATERIALS
55
Stan
dard
Old
Gra
de
Che
mic
al C
ompo
sitio
n %
, max
Mec
hani
cal R
equi
rem
ent
CS
iM
nP
SC
rN
iM
oO
ther
T.S
.m
inM
Pa
0.17
-0.2
30.
17-0
.37
0.35
-0.6
50.
035
0.03
50.
250.
30-
Cu:
0.25
410-
530
245
20-
-
0.20
0.55
1.0-
1.60
0.04
00.
040
--
-V
:0.0
2-0.
15;
Nb:
0.01
5-0.
060;
Ti:0
.02-
0.20
470-
630
345
20-
-
0.30
-1.
250.
030
0.03
0-
--
-46
036
019
--
0.26
-1.
350.
030
0.03
0-
--
-52
041
517
--
0.26
-1.
400.
030
0.03
0-
-53
545
017
--
0.23
-1.
600.
030
0.03
0-
--
-57
048
516
--
0.18
-1.
800.
030
0.03
0-
--
-62
5-82
555
515
--
0.20
0.45
1.60
0.02
50.
020
--
--
460
360-
515
20-
Rt0
.5/R
m:0
.88m
ax0.
210.
451.
600.
025
0.02
0-
--
-52
041
5-56
518
-R
t0.5/R
m:0
.88m
ax0.
160.
451.
600.
025
0.02
0-
-53
545
0-57
018
-R
t0.5/R
m:0
.90m
ax0.
160.
451.
700.
025
0.02
0-
--
-57
048
5-60
518
-R
t0.5/R
m:0
.90m
ax0.
160.
451.
800.
025
0.02
0-
--
-62
555
5-67
518
-R
t0.5/R
m:0
.90m
ax0.
17-0
.23
0.17
-0.3
70.
35-0
.65
0.03
00.
020
0.25
0.25
0.15
Cu:
0.20
;V:0
.08
410-
550
245
24-
AK
V35
J0.
12-0
.18
0.17
-0.3
70.
40-0
.70
0.03
00.
020
0.80
-1.1
00.
300.
40-0
.55
Cu:
0.20
440-
640
235
2117
0A
KV
35J
0.15
0.50
0.60
0.03
00.
020
4.00
-6.0
00.
600.
45-0
.60
Cu:
0.20
390-
590
195
2218
7A
KV
35J
0.04
-0.1
01.
002.
000.
030
0.02
018
.00-
20.0
08.
00-1
1.00
-C
u:0.
2052
020
535
--
0.12
-0.2
00.
20-0
.55
1.20
-1.6
00.
025
0.02
0-
--
-49
0-66
532
530
-A
KV
21J
(-45
)
0.12
0.17
-0.3
71.
850.
025
0.02
0-
--
V:0
.12
450
300
30-
AK
V21
J(-
70)
Not
e:
6)Th
e va
lue
of y
ield
stre
ngth
is th
e lo
wer
one
.
7)Th
e co
mpa
rison
bet
wee
n th
ese
stee
l gra
des
and
the
spec
ifica
tion
of A
PI 5
L sh
all b
e as
the
follo
win
g:
(how
ever
, the
acc
ordi
ngly
gra
des
may
be
diffe
rent
at o
ther
fact
ors)
L360
-X52
L415
-X60
L450
-X65
L485
-X70
L555
-X80
8)Th
e ab
ove
tabl
e in
dica
tes
the
chem
ical
requ
irem
ents
of t
he w
elde
d pi
pes.
For g
rade
s be
low
L45
0, th
e m
ax.
C c
onte
nt d
ecre
ases
eac
h 0.
01%
than
the
spec
ified
one
, an
incr
ease
of 0
.05
% M
n. m
ay b
e pe
rmitt
ed o
n
the
spec
ified
max
. one
. Hoe
ver,
for t
he g
rade
s be
low
L36
0,th
e m
ax. M
n. c
onte
nt is
1.4
5%, a
nd fo
r the
grad
es a
bove
L36
0,a
max
.Mn
cont
ent i
s 1.
60%
. For
L48
5 an
d L5
55, t
he m
ax. C
con
tent
dec
reas
es e
ach
0.01
% th
an th
e sp
ecifi
ed o
ne, a
n in
crea
se o
f 0.0
5 %
Mn.
may
be
perm
itted
on
the
spec
ified
max
. one
up
to 0
.20%
. As
for t
he d
etai
ls fo
r the
oth
er m
icro
elem
ents
,ple
ase
refe
r the
sta
ndar
ds.
9)Th
e va
lue
of y
ield
stre
ngth
is th
e sp
ecifi
ed to
tal e
xten
sion
stre
ngth
Rt0
.5. A
s fo
r the
ratio
of y
ield
stre
ngth
and
the
requ
irem
ents
of i
mpa
ct te
st, p
leas
e re
fer t
he s
tand
ards
.
10)U
nder
the
spec
ified
max
.C c
onte
nt, I
f dec
reas
ing
each
0.0
1% C
, an
incr
ease
of 0
.05
% M
n. m
ay b
e
perm
itted
on
the
spec
ified
max
. one
up
to m
ax. M
n 0.
20%
, as
for o
ther
mic
roel
emen
ts a
nd th
e C
EV, p
leas
e
refe
r the
sta
ndar
ds.
20-
Q345
B16
Mn,16
MnRE
L360
-L4
15-
L450
-L4
85-
L555
-L3
60-
L415
-L4
50-
L485
-L5
55-
20-
15Cr
Mo-
1Cr5
Mo-
1Cr1
9Ni9
-
16Mn
DG-
09Mn
2VDG
-
GB/T
8163
1)
New
Gra
de
GB/T
9711
.17) 8)
9)
GB/T
9711
.27)9)10
)
GB 99
48 1)6
)
GB/T
1898
41)6)
6)R
eL
7)A
PI
5L
L360
-X52
L415
-X60
L450
-X65
L485
-X70
L555
-X80
8)L
45
0C
0.0
1%
Mn
0.0
5%
Mn
L360
Mn
1.45
%L3
60M
n1.
60%
L485
L555
C0.
01%
M
n0.
05%
Mn
Mn
0.2%
9)(p
roof
str
engt
h, t
otal
ext
ensi
on)
Rt0
.510
)C
0.0
1%
CM
n0.
05%
Mn
Mn
0.2%
CE
V
Y.S
.m
inM
Pa
EL
.m
in %
HB
max
Oth
er
THE GENERAL MATERIALS
56
Stan
dard
Old
Gra
de
Che
mic
al C
ompo
sitio
n %
, max
Mec
hani
cal R
equi
rem
ent
CS
iM
nP
SC
rN
iM
oO
ther
T.S
.(R
m)
min
MPa
Y.S
.(R
p0.2
)
min
MPa
Not
e:11
) G
B/T
423
8 do
esn
t hav
e an
y lim
itatio
n to
the
cont
ent o
f Ni o
f thi
s ite
m g
rade
.
EL
.(A
)m
in %
HB
max
Oth
er
()
TH
E G
EN
ER
AL
ME
TA
LLIC
MA
TE
RIA
LS O
F C
HIN
ES
E P
RE
SS
UR
E P
IPIN
G C
OD
E(C
ON
TIN
UE
D)
New
Gra
de
11)G
B/T
423
8N
0.03
01.
002.
000.
045
0.03
018
.00-
20.0
08.
00-1
2.00
--
480
175
4018
7Z
60%
0.03
01.
002.
000.
045
0.03
016
.00-
18.0
010
.00-
14.0
02.
00-3
.00
-48
017
540
187
Z60
%0.
081.
002.
000.
045
0.03
018
.00-
20.0
08.
00-1
1.00
--
520
205
4018
7Z
60%
0.08
1.00
2.00
0.04
50.
030
16.0
0-18
.00
10.0
0-14
.00
2.00
-3.0
0-
520
205
4018
7Z
60%
0.08
1.00
2.00
0.04
50.
030
17.0
0-19
.00
9.00
-12.
00-
Ti:5
C-0
.70
520
205
4018
7Z
50%
0.08
1.00
2.00
0.04
50.
030
17.0
0-19
.00
9.00
-12.
00-
Nb:
10C
-1.1
052
020
540
187
Z50
%0.
030
0.75
2.00
0.04
50.
030
18.0
0-20
.00
8.00
-12.
00-
N:0
.10
485
170
4020
1-
0.03
00.
752.
000.
045
0.03
016
.00-
18.0
010
.00-
14.0
02.
00-3
.00
N:0
.10
485
170
4021
7-
0.08
0.75
2.00
0.04
50.
030
18.0
0-20
.00
8.00
-10.
50-
N:0
.10
515
205
4020
10.
080.
752.
000.
045
0.03
016
.00-
18.0
010
.00-
14.0
02.
00-3
.00
N:0
.10
515
205
4021
7-
0.08
0.75
2.00
0.04
50.
030
17.0
0-19
.00
9.00
-12.
00-
N:0
.10;
Ti5C
515
205
4021
7-
0.08
0.75
2.00
0.04
50.
030
17.0
0-19
.00
9.00
-13.
00-
Nb:
10C
-1.0
051
520
540
201
-0.
080.
752.
000.
040
0.03
018
.00-
20.0
08.
00-1
1.00
--
520
210
35-
-0.
030
0.75
2.00
0.04
00.
030
18.0
0-20
.00
8.00
-12.
00-
-48
018
035
--
0.08
0.75
2.00
0.04
00.
030
17.0
0-19
.00
9.00
-12.
00-
Ti:
5C-0
.70
520
210
35-
-0.
080.
752.
000.
040
0.03
017
.00-
19.0
09.
00-1
2.00
-N
b:10
C-1
.10
520
210
35-
-0.
080.
752.
000.
040
0.03
016
.00-
18.0
010
.00-
14.0
02.
00-3
.00
-52
021
035
--
0.03
00.
752.
000.
040
0.03
016
.00-
18.0
010
.00-
14.0
02.
00-3
.00
-48
018
035
--
0.07
1.00
2.00
0.03
50.
030
17.0
0-19
.00
8.00
-11.
00-
-52
020
535
--
0.03
01.
002.
000.
035
0.03
018
.00-
20.0
08.
00-1
2.00
--
480
175
35-
-0.
081.
002.
000.
035
0.03
017
.00-
19.0
09.
00-1
2.00
-Ti
:5C
520
205
35-
-0.
081.
002.
000.
035
0.03
017
.00-
19.0
09.
00-1
3.00
-N
bTa
:10C
-1.0
052
020
535
--
0.08
1.00
2.00
0.03
50.
030
16.0
0-18
.00
11.0
0-14
.00
2.00
-3.0
0-
520
205
35-
-0.
030
1.00
2.00
0.03
50.
030
16.0
0-18
.00
12.0
0-15
.00
2.00
-3.0
0-
480
175
40-
-0.
071.
002.
000.
035
0.03
017
.00-
19.0
08.
00-1
1.00
--
520
205
35-
-0.
030
1.00
2.00
0.03
50.
030
18.0
0-20
.00
8.00
-12.
00-
-48
017
535
--
0.08
1.00
2.00
0.03
50.
030
17.0
0-19
.00
9.00
-12.
00-
Ti:
5C52
020
535
--
0.08
1.00
2.00
0.03
50.
030
17.0
0-19
.00
9.00
-13.
00-
Nb
10C
520
205
35-
-0.
081.
002.
000.
035
0.03
016
.00-
18.5
010
.00-
14.0
02.
00-3
.00
-52
020
535
--
0.03
01.
002.
000.
035
0.03
016
.00-
18.0
012
.00-
15.0
02.
00-3
.00
-48
017
535
--
022C
r19N
i10
00Cr
19N
i10
022C
r17N
i12M
o200
Cr17
Ni1
4Mo2
06Cr
19N
i10
0Cr1
8Ni9
06Cr
17N
i12M
o20C
r17N
i12M
o206
Cr18
Ni1
1Ti
0Cr1
8Ni1
0Ti
06Cr
18N
i11N
b0C
r18N
i11N
b02
2Cr1
9Ni1
000
Cr19
Ni1
002
2Cr1
7Ni1
2Mo2
00Cr
17N
i14M
o206
Cr19
Ni1
00C
r18N
i906
Cr17
Ni1
2Mo2
0Cr1
7Ni1
2Mo2
06Cr
18Ni
11Ti
11)
0Cr1
8Ni1
0Ti11
)
06Cr
18N
i11N
b0C
r18N
i11N
b06
Cr19
Ni1
00C
r18N
i902
2Cr1
9Ni1
000
Cr19
Ni1
006
Cr18
Ni1
1Ti
0Cr1
8Ni1
0Ti
06Cr
18N
i11N
b0C
r18N
i11N
b06
Cr17
Ni1
2Mo2
0Cr1
7Ni1
2Mo2
022C
r17N
i12M
o200
Cr17
Ni1
4Mo2
06Cr
19N
i10
0Cr1
8Ni9
022C
r19N
i10
00Cr
19N
i10
06Cr
18N
i11T
i0C
r18N
i10T
i06
Cr18
Ni1
1Nb
0Cr1
8Ni1
1Nb
06Cr
17N
i12M
o20C
r17N
i12M
o202
2Cr1
7Ni1
2Mo2
00Cr
17N
i14M
o206
Cr19
Ni1
00C
r18N
i902
2Cr1
9Ni1
000
Cr19
Ni1
006
Cr18
Ni1
1Ti
0Cr1
8Ni1
0Ti
06Cr
18N
i11N
b0C
r18N
i11N
b06
Cr17
Ni1
2Mo2
0Cr1
7Ni1
2Mo2
022C
r17N
i12M
o200
Cr17
Ni1
4Mo2
GB/T
1220
GB/T
1220
,GB
/T 12
21
GB/T
4237
GB/T
4237
,GB
/T 42
38
GB 1
3296
GB/T
1497
6
GB/T
1277
1
THE GENERAL MATERIALS
57
Stan
dard
Old
Gra
de
Che
mic
al C
ompo
sitio
n %
,max
Mec
hani
cal R
equi
rem
ent
CS
iM
nP
SC
rN
iM
oO
ther
T.S
.m
inM
Pa
0.17
-0.2
30.
17-0
.37
0.60
-1.0
00.
030
0.02
00.
250.
25-
Cu:0
.25
390-
540
215
2410
6-15
9AK
V34
J
0.13
-0.1
90.
20-0
.60
1.20
-1.6
00.
030
0.02
00.
300.
30-
Cu:0
.25
450-
600
275
2012
1-17
8AK
V31
J(0
)
0.12
-0.1
80.
10-0
.60
0.30
-0.8
00.
030
0.02
00.
80-1
.25
0.30
0.45
-0.6
5Cu
:0.2
544
0-61
027
520
118-
180
AKV
34J
0.09
-0.1
50.
17-0
.37
0.40
-0.7
00.
030
0.02
00.
90-1
.20
0.30
0.25
-0.3
5V:
0.15
-0.3
0;
Cu:0
.25
440-
610
255
1911
8-18
0A KV
34J
0.15
0.50
0.30
-0.6
00.
025
0.01
52.
00-2
.50
0.30
0.90
-1.1
0Cu
:0.2
551
0-68
031
018
136-
201
AKV
41J
0.15
0.50
0.60
0.03
00.
020
4.00
-6.0
00.
500.
45-0
.65
Cu:0
.25
590-
760
390
1817
4-22
9AK
V34
J
0.13
-0.1
80.
20-0
.60
1.20
-1.6
00.
025
0.01
50.
300.
40-
Nb:0
.030
;
Cu:0
.25;
450-
600
275
20-
AKV
27J(
-40
)
Als:
0.01
5
0.12
0.15
-0.3
51.
20-1
.60
0.02
50.
015
0.30
0.45
-0.8
5-
Nb:0
.050
;
Cu:0
.25;
420-
570
260
23AK
V47
J(-7
0)
Als:
0.01
5
0.07
1.00
2.00
0.03
50.
030
17.0
0-19
.00
8.00
-11.
00-
-52
020
535
139-
187
-
0.03
1.00
2.00
0.03
50.
030
18.0
0-20
.00
8.00
-12.
00-
-48
017
535
128-
187
-
0.08
1.00
2.00
0.03
50.
030
16.0
0-18
.00
10.0
0-14
.00
2.00
-3.0
0-
520
205
3513
9-18
7-
0.03
1.00
2.00
0.03
50.
030
16.0
0-18
.00
12.0
0-15
.00
2.00
-3.0
0-
480
175
3512
8-18
7-
0.08
1.00
2.00
0.03
50.
030
17.0
0-19
.00
9.00
-12.
00-
Ti:
5C52
020
535
139-
187
-
0.08
1.00
2.00
0.03
50.
030
16.0
0-19
.00
11.0
0-14
.00
1.80
-2.5
0Ti
:5C
-0.7
520
205
3513
9-18
7-
0.08
1.00
2.00
0.04
50.
030
18.0
0-20
.00
8.00
-11.
00-
--
--
--
0.03
01.
002.
000.
045
0.03
018
.00-
20.0
08.
00-1
2.00
--
--
--
-
0.08
1.00
2.00
0.04
50.
030
17.0
0-19
.00
9.00
-12.
00-
Ti:
5C-0
.7-
--
--
0.08
1.00
2.00
0.04
50.
030
17.0
0-19
.00
9.00
-12.
00-
Nb10
C-1.
10-
--
--
0.08
1.00
2.00
0.04
50.
030
16.0
0-18
.00
10.0
0-14
.00
2.00
-3.0
0-
--
--
-
0.03
01.
002.
000.
045
0.03
016
.00-
18.0
010
.00-
14.0
02.
00-3
.00
--
--
--
0.17
-0.2
40.
17-0
.37
0.35
-0.6
50.
035
0.03
50.
250.
25-
Cu:0
.20
412-
549
245
2411
7-15
6AK
V27
J
0.08
-0.1
50.
17-0
.37
0.40
-0.7
00.
035
0.03
50.
90-1
.20
0.30
0.25
-0.3
5V:
0.15
-0.3
0;
Cu:0
.20
440-
610
255
2113
2-18
3A KV
34J
0.08
-0.1
50.
500.
30-0
.60
0.03
00.
030
2.00
-2.5
00.
300.
90-1
.10
Cu:0
.20
450-
600
280
2013
5-18
0AK
V41
J
Not
e:
12)F
or th
e de
oxid
izin
g st
eel w
ith v
acuu
m c
arbo
n, th
e co
nten
t of S
i may
be
up to
0.1
2%
13)T
he fo
rgin
gs h
ave
the
grad
es o
f a
nd
, and
the
insp
ectio
n ite
ms
for e
ach
grad
e ar
e di
ffere
nt.
14)T
he m
echa
nica
l pro
perti
es v
ary
with
the
diffe
ret t
hick
ness
for f
orrg
ings
, det
ails
, ple
ase
refe
r the
sta
ndar
ds.
15)T
he fo
rgin
gs h
ave
the
grad
es o
f a
nd
, and
the
insp
ectio
n ite
ms
for e
ach
grad
e ar
e di
ffere
nt.
20-
16Mn
-15
CrMo
-
12Cr
1MoV
-
12Cr
2Mo1
-1C
r5Mo
-
16Mn
D-
09Mn
NiD-
0Cr18
Ni9-
00Cr
19Ni1
00C
r17Ni1
2Mo2
-00
Cr17
Ni14M
o2-
0Cr18
Ni10T
i-
0Cr18
Ni12M
o2Ti
-06
Cr19
Ni10
0Cr18
Ni902
2Cr19
Ni10
00Cr
19Ni1
006
Cr18
Ni11T
i0C
r18Ni1
0Ti
06Cr
18Ni1
1Nb
0Cr18
Ni11N
b06
Cr17
Ni12M
o20C
r17Ni1
2Mo2
022C
r17Ni1
2Mo2
00Cr
17Ni1
4Mo2
20-
12Cr
1MoV
-
12Cr
2Mo1
-
New
Gra
de
JB 4
72612
)13)
14)
12)
Si
0.1
2%
13)
414
)15
)3
Y.S
.m
inM
Pa
EL
.m
in %
JB 4
72712
)14)
15)
JB 47
2813
)14)
YB/T
5089
HB
max
Oth
er
DL 47
3
THE GENERAL MATERIALS
58
AS
ME
T
HE
GE
NE
RA
L M
ET
ALL
IC M
AT
ER
IALS
OF
AS
ME
PR
ES
SU
RE
PIP
ING
CO
DE
Cod
eG
rade
Che
mic
al C
ompo
sitio
n %
, m
ax M
echa
nica
l Req
uire
men
t
CS
iM
nP
SC
rN
iM
oO
ther
T.S
.m
inM
Pa
Y.S
.m
inM
Pa
EL
.m
in %
HB
max
Oth
er
0.30
-1.
200.
050.
045
0.40
0.40
0.15
Cu:
0.40
;V:0
.08
415
240
e 2)
--
0.30
-1.
200.
050.
045
0.40
0.40
0.15
Cu:
0.50
;V:0
.08
415
240
e 2)
--
0.35
0.10
-0.3
50.
60-1
.05
0.03
50.
040
0.30
0.40
0.12
Cu:
0.40
;V:0
.08
485
250
2218
7Z
30%
0.30
0.10
min
0.29
-1.0
60.
035
0.03
50.
400.
400.
15C
u:0.
40;V
:0.0
841
524
022
--
0.35
0.10
min
0.29
-1.0
60.
035
0.03
50.
400.
400.
15C
u:0.
40;V
:0.0
848
527
520
--
0.15
0.50
0.30
-0.6
00.
030
0.03
04.
0-6.
00.
500.
44-0
.65
-48
527
520
143-
217
Z35
%0.
150.
50-1
.00
0.30
-0.6
00.
030
0.03
08.
0-10
.0-
0.90
-1.1
0-
585
380
2017
9-21
7Z
40%
0.08
-0.1
20.
20-0
.50
0.30
-0.6
00.
020
0.01
08.
0-9.
50.
400.
85-1
.05
5)58
541
520
248
Z40
%0.
05-0
.15
0.50
-1.0
00.
30-0
.60
0.03
00.
030
1.00
-1.5
0-
0.44
-0.6
5-
415
205
2012
1-17
4Z
45%
0.10
-0.2
00.
50-1
.00
0.30
-0.8
00.
040
0.04
01.
00-1
.50
-0.
44-0
.65
-48
527
520
143-
207
Z30
%0.
10-0
.20
0.50
-1.0
00.
30-0
.80
0.04
00.
040
1.00
-1.5
0-
0.44
-0.6
5-
515
310
2015
6-20
7Z
30%
0.05
-0.1
50.
500.
30-0
.60
0.04
50.
045
0.80
-1.2
5-
0.44
-0.6
5-
415
220
2012
1-17
4Z
45%
0.10
-0.2
00.
10-0
.60
0.30
-0.8
00.
040
0.04
00.
80-1
.25
-0.
44-0
.65
-48
527
520
143-
207
Z30
%0.
05-0
.15
0.50
0.30
-0.6
00.
040
0.04
02.
00-2
.50
-0.
87-1
.13
-41
520
520
170
Z35
%0.
05-0
.15
0.50
0.30
-0.6
00.
040
0.04
02.
00-2
.50
-0.
87-1
.13
-51
531
020
156-
207
Z30
%0.
081.
002.
000.
045
0.03
018
.0-2
0.0
8.0-
11.0
--
515
205
30-
Z50
%0.
04-0
.10
1.00
2.00
0.04
50.
030
18.0
-20.
08.
0-11
.0-
-51
520
530
-Z
50%
0.03
01.
002.
000.
045
0.03
018
.0-2
0.0
8.0-
13.0
--
485
170
30-
Z50
%0.
081.
002.
000.
045
0.03
016
.0-1
8.0
10.0
-14.
02.
00-3
.00
-51
520
530
-Z
50%
0.04
-0.1
01.
002.
000.
045
0.03
016
.0-1
8.0
10.0
-14.
02.
00-3
.00
-51
520
530
-Z
50%
0.03
01.
002.
000.
045
0.03
016
.0-1
8.0
10.0
-15.
02.
00-3
.00
-48
517
030
-Z
50%
0.08
1.00
2.00
0.04
50.
030
17.0
-19.
09.
0-12
.0-
Ti:5
C-0
.751
520
530
-Z
50%
0.04
-0.1
01.
002.
000.
045
0.03
017
.0-1
9.0
9.0-
12.0
-Ti
:4C
-0.7
515
205
30-
Z50
%0.
081.
002.
000.
045
0.03
017
.0-2
0.0
9.0-
13.0
-N
b:10
C-1
.10
515
205
30-
Z50
%0.
04-0
.10
1.00
2.00
0.04
50.
030
17.0
-20.
09.
0-13
.0-
Nb:
8C-1
.10
515
205
30-
Z50
%0.
030
1.00
2.00
0.03
00.
020
21.0
-23.
04.
5-6.
52.
5-3.
5N
:0.0
8-0.
2062
045
025
-Z
45%
0.03
01.
002.
000.
030
0.02
022
.0-2
3.0
4.5-
6.5
3.0-
3.5
N:0
.14-
0.20
655
485
25-
Z45
%
1)C
u N
iC
rM
oV
1.00
%2)
e =
1940
A0.
2 /U0.
9
3)C
0.0
1%
CM
n0.
06%
Mn
1.35
%4)
Cr
Mo
0.32
%5)
Nb:
0.06
-0.1
0, N
:0.0
3-0.
07, A
l:0.0
2, V
:0.1
8-0.
25, T
i:0.0
1, Z
r:0.0
16)
F304
F304
LF3
16F3
16L
N0.
10%
NO
TE:
1)Th
e su
m o
f Cu,
Ni,
Cr,
Mo
and
V s
hall
not e
xcee
d 1.
00 %
.2)
e =
1940
A0.
2 /U0.
9D
etai
ls re
fer t
he s
peci
ficat
ion.
3)B
elow
the
spec
ified
max
.C, I
f the
con
tent
C d
ecre
ases
eac
h 0.
01 %
, an
incr
ease
of 0
.06%
man
gane
se w
illbe
per
mitt
ed u
p to
a m
axim
um o
f 1.3
5%.
4)Th
e su
m o
f chr
omiu
m a
nd m
olyb
denu
m s
hall
not e
xcee
d 0.
32 %
.5)
Nb:
0.06
-0.1
0, N
:0.0
3-0.
07, A
l:0.0
2, V
:0.1
8-0.
25, T
i:0.0
1, Z
r:0.0
1.6)
Gra
des
F304
, F30
4L, F
316
and
F316
L sh
all h
ave
a m
axim
um n
itrog
en c
onte
nt o
f 0.1
0%.
B 1)
B 1)
A10
51) 3
) 4)
B 1)
3)
C 1)
3)
F5 F9 F91
F11
CL1
F11
CL2
F11
CL3
F12
CL1
F12
CL2
F22
CL1
F22
CL3
F304
6)
F304
HF3
04L
6)
F316
6)
F316
HF3
16L
6)
F321
F321
HF3
47F3
47H
F51
F60
AS
TM A
53/
ASM
E SA
53
AS
TM A
105
/AS
ME
SA 1
05/
AS
TM A
106
/AS
ME
SA 1
06
AS
TM A
182
/AS
ME
SA 1
82
THE GENERAL MATERIALS
59
Cod
eG
rade
Che
mic
al C
ompo
sitio
n %
,max
Mec
hani
cal R
equi
rem
ent
CS
iM
nP
SC
rN
iM
oO
ther
T.S
.m
inM
Pa
Y.S
.m
inM
Pa
0.30
0.10
min
0.29
-1.0
60.
050
0.05
80.
400.
400.
15C
u:0.
40;V
:0.0
841
5-65
524
022
197
-0.
350.
10 m
in0.
29-1
.06
0.05
00.
058
0.40
0.40
0.15
Cu:
0.40
;V:0
.08
485-
655
275
2219
7-
0.15
0.50
0.30
-0.6
00.
040
0.03
04.
0-6.
0-
0.44
-0.6
5-
415-
585
205
2221
7-
0.15
0.50
0.30
-0.6
00.
040
0.03
04.
0-6.
0-
0.44
-0.6
5-
520-
690
310
2221
7-
0.15
1.00
0.30
-0.6
00.
030
0.03
08.
0-10
.0-
0.90
-1.1
0-
415-
585
205
2221
7-
0.15
1.00
0.30
-0.6
00.
030
0.03
08.
0-10
.0-
0.90
-1.1
0-
520-
690
310
2221
7-
0.08
-0.1
20.
20-0
.50
0.30
-0.6
00.
020
0.01
08.
0-9.
50.
400.
85-1
.05
12)
585-
760
415
2024
8-
0.05
-0.1
50.
50-1
.00
0.30
-0.6
00.
030
0.03
01.
00-1
.50
-0.
44-0
.65
-41
5-58
520
522
197
-0.
05-0
.20
0.50
-1.0
00.
30-0
.80
0.04
00.
040
1.00
-1.5
0-
0.44
-0.6
5-
485-
655
275
2219
7-
0.05
-0.2
00.
50-1
.00
0.30
-0.8
00.
040
0.04
01.
00-1
.50
-0.
44-0
.65
-52
0-69
031
022
197
-0.
05-0
.20
0.60
0.30
-0.8
00.
045
0.04
50.
80-1
.25
-0.
44-0
.65
-41
5-58
522
022
197
-0.
05-0
.20
0.60
0.30
-0.8
00.
045
0.04
50.
80-1
.25
-0.
44-0
.65
-48
5-65
527
522
197
-0.
05-0
.15
0.50
0.30
-0.6
00.
040
0.04
01.
90-2
.60
-0.
87-1
.13
-41
5-58
520
522
197
-0.
05-0
.15
0.50
0.30
-0.6
00.
040
0.04
01.
90-2
.60
-0.
87-1
.13
-52
0-69
031
022
197
-0.
080.
752.
000.
045
0.03
018
.0-2
0.0
8.0-
10.5
-N
:0.1
051
520
540
201
-0.
04-0
.10
0.75
2.00
0.04
50.
030
18.0
-20.
08.
0-10
.5-
-51
520
540
201
-0.
030
0.75
2.00
0.04
50.
030
18.0
-20.
08.
0-12
.0-
N:0
.10
485
170
4020
1-
0.08
0.75
2.00
0.04
50.
030
16.0
-18.
010
.0-1
4.0
2.00
-3.0
0N
:0.1
051
520
540
217
-0.
04-0
.10
0.75
2.00
0.04
50.
030
16.0
-18.
010
.0-1
4.0
2.00
-3.0
0-
515
205
4021
7-
0.03
00.
752.
000.
045
0.03
016
.0-1
8.0
10.0
-14.
02.
00-3
.00
N:0
.10
485
170
4021
7-
0.08
0.75
2.00
0.04
50.
030
17.0
-19.
09.
0-12
.0-
N:0
.10;
Ti:5
(C+N
)-0.7
515
205
4021
7-
0.04
-0.1
00.
752.
000.
045
0.03
017
.0-1
9.0
9.0-
12.0
-Ti
:4(C
+N)-0
.751
520
540
217
-0.
080.
752.
000.
045
0.03
017
.0-1
9.0
9.0-
13.0
-N
b:10
C-1
.00
515
205
4020
1-
0.04
-0.1
00.
752.
000.
045
0.03
017
.0-2
0.0
9.0-
13.0
-N
b:8C
-1.0
051
520
540
201
-0.
081.
002.
000.
045
0.03
018
.0-2
0.0
8.0-
11.0
--
515
205
35-
-0.
04-0
.10
1.00
2.00
0.04
50.
030
18.0
-20.
08.
0-11
.0-
-51
520
535
--
0.03
51.
002.
000.
045
0.03
018
.0-2
0.0
8.0-
13.0
--
485
170
35-
-0.
081.
002.
000.
045
0.03
016
.0-1
8.0
11.0
-14.
02.
00-3
.00
-51
520
535
--
0.04
-0.1
01.
002.
000.
045
0.03
016
.0-1
8.0
11.0
-14.
02.
00-3
.00
-51
520
535
--
0.03
51.
002.
000.
045
0.03
016
.0-1
8.0
10.0
-14.
02.
00-3
.00
-48
517
035
--
7)C
0.3
5%
8)C
0.3
5%
Si
0.3
5%
9)C
0.0
1%
CM
n0.
06%
Mn
1.35
%10
)Cu
Ni
Cr
Mo
1.00
%11
)Cr
Mo
0.32
%12
)V:0
.18-
0.25
, Nb:
0.06
-0.1
0, N
:0.0
3-0.
07, A
l:0.0
2, T
i:0.0
1, Z
r:0.0
1.13
)TP
316
TP31
6HN
i10
.0-1
4.0
%
NO
TE:
7)Fi
tting
s m
ade
from
bar
s or
pla
tes
shal
l hav
e m
ax.C
0.3
5.8)
Fitti
ngs
mad
e fro
m fo
rgin
gs s
hall
have
C m
ax.0
.35
and
Si m
ax. 0
.35
with
ou m
in.li
mita
tion.
9)B
elow
the
spec
ified
max
.C, I
f the
con
tent
C d
ecre
ases
eac
h 0.
01 %
, an
incr
ease
of 0
.06%
Mn
will
be
perm
itted
up
to a
max
imum
of 1
.35%
.10
)The
sum
of C
u, N
i, C
r, an
d M
o sh
all n
ot e
xcee
d 1.
00 %
.11
)The
sum
of C
r and
Mo
shal
l not
exc
eed
0.32
%.
12)V
:0.1
8-0.
25, N
b:0.
06-0
.10,
N:0
.03-
0.07
, Al:0
.02,
Ti:0
.01,
Zr:0
.01.
13)F
or w
elde
d TP
316
and
TP31
6H p
ipe,
the
rang
e of
Ni s
hall
be 1
0.0
14.0
%.
WPB
7)8
)9)1
0)11
)
WPC
8)9)
10)1
1)
WP5
CL1
WP5
CL3
WP9
CL1
WP9
CL3
WP9
1W
P11
CL1
WP1
1 CL
2W
P11
CL3
WP1
2 CL
1W
P12
CL2
WP2
2 CL
1W
P22
CL3
304
304H
304L
316
316H
316L
321
321H
347
TP34
7HTP
304
TP30
4HTP
304L
TP31
6 13
)
TP31
6H 13
)
TP31
6L
AS
TM A
234
/AS
ME
SA 2
34
AS
TM A
240
/AS
ME
SA 2
40
AS
TM A
312
/AS
ME
SA 3
12
EL
.m
in %
HB
max
Oth
er
THE GENERAL MATERIALS
60
THE GENERAL MATERIALS
Che
mic
al C
ompo
sitio
n %
, max
Mec
hani
cal R
equi
rem
ent
Oth
erT
.S.
min
MPa
Y.S
.m
inM
Pa
0.08
1.00
2.00
0.04
50.
030
17.0
-19.
09.
0-12
.0-
N:0
.10;
Ti:5
C-0
.70
515
205
35-
-
0.04
-0.1
01.
002.
000.
045
0.03
017
.0-1
9.0
9.0-
12.0
-Ti
:4C
-0.6
051
520
535
--
0.08
1.00
2.00
0.04
50.
030
17.0
-19.
09.
0-13
.0-
Nb:
10C
-1.0
051
520
535
--
0.04
-0.1
01.
002.
000.
045
0.03
017
.0-1
9.0
9.0-
13.0
-N
b:8C
-1.0
515
205
35-
-
0.30
0.10
min
0.29
-1.0
60.
025
0.02
5-
--
-41
524
022
--
0.20
-0.
40-1
.06
0.02
50.
025
-1.
60-2
.24
-C
u:0.
75-1
.25
435
315
(28)
--
0.19
0.18
-0.3
70.
31-0
.64
0.02
50.
025
-3.
18-3
.82
--
450
240
22-
-
0.13
0.13
-0.3
20.
900.
025
0.02
5-
8.40
-9.6
0-
-69
051
516
--
0.15
0.50
0.30
-0.6
00.
025
0.02
54.
00-6
.00
-0.
45-0
.65
-41
520
522
--
0.15
1.00
-2.0
00.
30-0
.60
0.02
50.
025
4.00
-6.0
0-
0.44
-0.6
5-
415
205
22-
-
0.12
0.50
0.30
-0.6
00.
025
0.02
54.
00-6
.00
-0.
45-0
.65
16)
415
205
22-
-
0.15
0.25
-1.0
00.
30-0
.60
0.02
50.
025
8.0-
10.0
-0.
90-1
.10
-41
520
522
--
0.08
-0.1
20.
20-0
.50
0.30
-0.6
00.
020
0.01
08.
00-9
.50
0.40
0.85
-1.0
517
585
415
2025
0-
0.05
-0.1
50.
50-1
.00
0.30
-0.6
00.
025
0.02
51.
00-1
.50
-0.
44-0
.65
-41
520
522
--
0.05
-0.1
50.
500.
30-0
.61
0.02
50.
025
0.80
-1.2
5-
0.44
-0.6
5-
415
220
22-
-
0.05
-0.1
50.
500.
30-0
.60
0.02
50.
025
1.90
-2.6
0-
0.87
-1.1
3-
415
205
22-
-
0.30
0.15
-0.3
00.
60-1
.35
0.03
50.
040
0.30
0.40
0.12
Cu:
0.40
;Nb:
0.02
V:0
.08,
485-
655
250
2219
7-
0.20
-0.
40-1
.06
0.03
50.
040
0.30
1.60
-2.2
40.
12C
u:0.
75-1
.25,
Nb:
0.02
;V:0
.03
435-
605
315
2519
7-
0.20
0.20
-0.3
50.
900.
035
0.04
00.
303.
3-3.
70.
12C
u:0.
40;N
b:0.
02
V:0
.03
485-
655
260
2219
7-
NO
TE:
14)F
or T
P321
SM
LS p
ipes
with
tich
knes
s(T.
)9.
53m
m (3
/8 in
.)and
TP3
21H
SM
LS p
ipes
with
T4.
76m
m (3
/16
in.),
the
min
. ten
sion
ste
nght
is 4
85M
Pa
70ks
ian
d th
e m
in. y
ield
stre
ngth
is17
0MP
a25
ksi
,
15)B
elow
the
spec
ified
max
.C, I
f the
con
tent
C d
ecre
ases
eac
h 0.
01 %
, an
incr
ease
of 0
.06%
man
gane
se w
ill
be p
erm
itted
up
to a
max
imum
of 1
.35%
.
16)G
rade
P5c
sha
ll ha
ve a
Ti c
onte
nt 4
C-0
.7%
; or a
Nb
cont
ent
8-10
C%
.
17)G
rade
P91
sha
ll ha
ve V
:0.1
8-0.
25, N
:0.0
3-0.
07, A
l:0.0
2, N
b:0.
06-0
.10,
Ti:0
.01,
Zr:0
.01.
18)T
he s
um o
f Cu,
Ni,
Cr,V
and
Mo
shal
l not
exc
eed
1.00
% d
urin
g he
at a
naly
sis.
19)T
he s
um o
f Cr a
nd M
o sh
all n
ot e
xcee
d 0.
32 %
dur
ing
heat
ana
lysi
s.
20)P
er a
gree
men
t, th
e co
nten
t of N
b m
ay b
e 0.
05 %
dur
ing
heat
ana
lysi
s an
d 0.
06%
dur
ing
prod
uct a
naly
sis.
EL
.m
in %
HB
max
Oth
er
AS
ME
(
)T
HE
GE
NE
RA
L M
ET
ALL
IC M
AT
ER
IAL
FOR
AS
ME
PR
ES
SU
RE
PIP
ING
CO
DE
(CO
NT
INU
ED
)
Cod
eG
rade
CS
iM
nP
SC
rN
iM
o
14)
9.53
mm
(3/
8 in
.)TP
321
4.76
mm
(3/
16 in
.)TP
321H
485M
Pa
70ks
i17
0MP
a25
ksi
15)
C0
.01
% C
Mn
0.05
% M
n1.
35%
16)P
5c4
C-0
.7%
Ti
8-10
C%
Nb
17)P
91V
:0.1
8-0.
25, N
:0.0
3-0.
07, A
l:0.0
2, N
b:0.
06-0
.10,
Ti:0
.01,
Zr:0
.01
18)
Cu
Ni
Cr
VM
o1.
00%
19)
Cr
Mo
0.32
%20
)N
b0
.05
%0
.06
%
TP32
1 14
TP32
1H 14
TP34
7TP
347H
6 15
)
9 3 8 P5 P5b
P5c
P9 P91
P11
P12
P22
LF2
CL1
&CL
2 1
8)19
)20)
LF9
19)
LF3
CL1
&CL
2 19
)
AS
TM A
333
/AS
ME
SA 3
3325
AS
TM A
350
/AS
ME
SA 3
5025
AS
TM A
312
/AS
ME
SA 3
12
AS
TM A
335
/AS
ME
SA 3
35
61
Cod
eG
rade
Che
mic
al C
ompo
sitio
n %
, max
Mec
hani
cal R
equi
rem
ent
CS
iM
nP
SC
rN
iM
oO
ther
T.S
.m
inM
Pa
Y.S
.m
inM
Pa
0.15
0.55
0.25
-0.6
60.
035
0.03
03.
90-6
.10
-0.
40-0
.70
-41
5-58
520
5(5
15-6
90)
(310
)18
-Z
40%
0.15
1.05
0.25
-0.6
60.
030
0.03
07.
90-1
0.10
-0.
85-1
.15
-41
5-58
520
5(5
15-6
90)
(310
)18
-Z
40%
V:0
.16-
0.27
Nb:
0.05
-0.1
10.
06-0
.15
0.18
-0.5
60.
25-0
.66
0.02
50.
012
7.90
-9.6
00.
430.
80-1
.10
N:0
.025
-0.0
8058
5-76
041
518
--
Al:0
.02;
Ti:0
.01
Zr:0
.01
0.04
-0.1
70.
44-0
.86
0.35
-0.7
30.
035
0.03
50.
94-1
.56
-0.
40-0
.70
-41
5-58
524
0(5
15-6
90)
(310
)22
--
0.04
-0.1
70.
13-0
.45
0.35
-0.7
30.
035
0.03
50.
74-1
.21
-0.
40-0
.65
-38
0-55
023
0(4
50-5
85)
(275
)22
--
0.04
-0.1
50.
500.
25-0
.66
0.03
50.
035
1.88
-2.6
2-
0.85
-1.1
5-
415-
585
205
(515
-690
)(3
10)
18-
Z40
%
0.08
1.00
2.00
0.04
50.
030
18.0
-20.
08.
0-11
.0-
-51
520
528
--
0.04
-0.1
01.
002.
000.
045
0.03
018
.0-2
0.0
8.0-
11.0
--
515
205
28-
-0.
030
1.00
2.00
0.04
50.
030
18.0
-20.
08.
0-12
.0-
-48
517
028
--
0.08
1.00
2.00
0.04
50.
030
16.0
-18.
010
.0-1
4.0
2.00
-3.0
0-
515
205
28-
-0.
04-0
.10
1.00
2.00
0.04
50.
030
16.0
-18.
010
.0-1
4.0
2.00
-3.0
0-
515
205
28-
-0.
030
1.00
2.00
0.04
50.
030
16.0
-18.
010
.0-1
4.0
2.00
-3.0
0-
485
170
28-
-0.
081.
002.
000.
045
0.03
017
.0-1
9.0
9.0-
12.0
-Ti
:5(C
+N2)-
0.70
515
205
28-
-0.
04-0
.10
1.00
2.00
0.04
50.
030
17.0
-19.
09.
0-12
.0-
Ti:4
(C+N
2)-0.
7051
520
528
--
0.08
1.00
2.00
0.04
50.
030
17.0
-19.
09.
0-12
.0-
Nb:
10C
-1.1
051
520
528
--
0.04
-0.1
01.
002.
000.
045
0.03
017
.0-1
9.0
9.0-
12.0
-N
b:8C
-1.1
051
520
528
--
0.30
0.15
-0.4
00.
50-1
.35
0.03
50.
040
0.30
0.40
0.12
Cu:
0.40
;V:0
.08,
Nb:
0.02
415-
655
240
22-
-
0.20
-0.
40-1
.06
0.03
00.
030
-1.
60-2
.24
-C
u:0.
75-1
.25
435-
610
315
20-
-0.
200.
13-0
.37
0.31
-0.6
40.
050.
05-
3.2-
3.8
--
450-
620
240
22-
-0.
130.
13-0
.37
0.90
0.03
00.
030
-8.
4-9.
6-
-69
0-86
551
516
--
0.28
0.13
-0.4
50.
980.
035
0.03
5-
--
-45
0-58
524
023
--
0.31
0.13
-0.4
51.
300.
035
0.03
5-
--
-48
5-62
026
021
--
0.24
0.13
-0.4
50.
79-1
.30
0.03
50.
035
--
--
450-
585
240
23-
-0.
270.
13-0
.45
0.79
-1.3
00.
035
0.03
5-
--
-48
5-62
026
021
--
0.03
01.
02.
000.
030
0.02
021
.0-2
3.0
4.5-
6.5
2.5-
3.5
N:0
.08-
0.20
620
450
2029
0-
0.03
01.
002.
000.
030
0.02
022
.0-2
3.0
4.5-
6.5
3.0-
3.5
N:0
.14-
0.20
655
450
2029
0-
21)
Nb
0.05
%0.
06%
22)
Mn
0.90
%23
) M
n0.
98%
24
) C
Mn
25
) 2
6)
Not
e:21
)Per
agr
eem
ent,
the
cont
ent o
f Nb
may
be
0.05
% d
urin
g he
at a
naly
sis
and
0.06
% d
urin
g pr
oduc
t ana
lysi
s.22
)Fitt
ings
mad
e fro
m p
late
s or
forg
ings
sha
ll ha
ve M
n M
ax.0
.90
%.
23)F
ittin
gs m
ade
from
pla
tes
shal
l hav
e M
n M
ax 0
.98
%.
24)T
he c
onte
nts
of C
and
Mn
may
var
y w
ith th
e di
ffere
nt th
ickn
ess,
ple
ase
refe
r the
rele
vant
sta
ndar
ds.
25)A
s fo
r the
impa
ct te
st te
mpe
ratu
re a
nd th
e te
st p
rope
rties
,ple
ase
refe
r the
rele
vant
sta
ndar
ds.
26)
Bec
ause
of t
he d
iffer
ent C
lass
,the
plat
es p
rope
rties
are
diff
eren
t, re
fer t
he s
tand
ards
.
5 9 91 11 12 22
WP3
04W
P304
HW
P304
LW
P316
WP3
16H
WP3
16L
WP3
21W
P321
HW
P347
WP3
47H
WPL
6 21
)
WPL
9W
PL3 2
2)
WPL
8 23
)
65 24
)
70 24
)
6524
)
70 24
)
S318
03S3
2205
AS
TM A
387
/AS
ME
SA 3
8726
AS
TM A
403
/AS
ME
SA 4
03
AS
TM A
420
/AS
ME
SA 4
2025
EL
.m
in %
HB
max
Oth
er
AS
TM A
515
/AS
ME
SA 5
15A
STM
A 5
16/
ASM
E SA
516
AS
TM A
815
/AS
ME
SA 8
15
THE GENERAL MATERIALS
62
90BW 90 LR Elbow
Nominal Size
: DN1200 NPS 48 STD 9.53mm Note: the weight for the size more than DN1200(NPS48) is calculated onthe basis of thickness 9.53mm.
Referenced Weight Lists
DN NPS
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
1300
1400
1500
1600
1700
1800
1900
2000
Sch10 Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140 Sch160 XXS
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
52
56
60
64
68
72
76
80
0.06
0.08
0.13
0.21
0.28
0.47
0.79
1.16
1.55
2.02
3.46
4.98
9.57
16.7
25.9
34.7
45.4
56.2
82.2
143
170
200
232
267
304
343
386
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
17.6
27.5
39.3
62.5
82.0
104
154
187
223
347
403
464
528
597
669
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.07
0.09
0.14
0.24
0.35
0.59
1.32
1.95
2.62
3.39
-
-
19.4
33.6
51.5
74.9
98.3
145
204
248
331
-
478
577
658
743
834
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.08
0.11
0.16
0.28
0.40
0.71
1.42
2.22
3.12
4.22
7.15
11.2
22.4
39.7
58.3
74.9
98.3
125
154
187
223
262
304
349
398
449
504
562
623
687
754
825
898
1107
1284
1475
1679
1869
2126
2372
2626
0.08
0.11
0.16
0.28
0.40
0.71
1.42
2.22
3.12
4.22
7.15
11.2
22.4
39.7
62.9
87.1
130
185
242
-
403
-
-
-
722
817
997
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
28.0
53.7
86.0
117
169
244
326
426
561
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.11
0.14
0.12
0.24
0.53
0.98
1.87
3.01
4.28
5.86
10.2
16.8
34.1
53.7
76.9
98.9
130
165
204
248
295
347
403
464
528
597
669
746
828
913
1003
1096
1194
-
-
-
-
-
-
-
-
0.11
0.14
0.12
0.24
0.53
0.98
1.87
3.01
4.28
5.86
10.2
16.8
34.1
63.2
104
146
215
302
410
541
698
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
40.0
75.5
126
180
259
367
502
654
865
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
7.44
13.2
21.4
47.7
87.6
148
207
302
431
581
763
1011
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
53.2
102
164
234
351
484
669
870
1137
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.13
0.19
0.28
0.47
0.71
1.46
2.45
4.20
-
8.81
16.1
26.7
58.6
113
188
259
385
545
744
974
1277
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.17
0.24
0.36
0.64
0.94
1.76
3.35
5.45
-
10.8
18.9
31.3
56.9
102
148
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
kg
REFERENCED WEIGHT LISTS
63
90BW 90 SR Elbow
: DN1200 NPS 48 STD 9.53mm Note: the weight for the size more than DN1200(NPS48) is calculated onthe basis of thickness 9.53mm.
Referenced Weight Lists
kg
Nominal Size
DN NPS
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
1300
1400
1500
1600
1700
1800
1900
2000
Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140 Sch160 XXS
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
52
56
60
64
68
72
76
80
-
-
-
-
-
-
-
-
-
-
11.7
18.3
26.2
41.8
54.6
69.3
103
125
149
231
269
309
352
398
446
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.09
0.16
0.23
0.39
0.89
1.30
1.76
2.28
-
-
12.9
22.4
34.4
50.0
65.4
96.6
136
165
221
-
334
385
439
496
555
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.11
0.19
0.27
0.48
0.95
1.48
2.09
2.83
4.78
7.42
14.9
26.5
38.9
50.0
65.4
83.0
103
125
149
174
203
233
265
300
336
374
415
458
503
550
599
738
854
983
1116
1264
1418
1581
1751
0.11
0.19
0.27
0.48
0.95
1.48
2.09
2.83
4.78
7.42
14.9
26.5
42.0
58.2
86.5
123
161
-
269
-
-
-
482
545
664
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
18.6
35.8
57.4
78.0
112
162
218
284
374
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.14
0.25
0.36
0.66
1.26
2.01
2.87
3.93
6.80
11.2
22.7
35.8
51.4
66.1
86.5
110
136
165
197
231
269
309
352
398
446
497
552
609
669
730
796
-
-
-
-
-
-
-
-
0.14
0.25
0.36
0.66
1.26
2.01
2.87
3.93
6.80
11.2
22.7
42.1
69.6
97.3
143
201
273
361
466
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
26.6
50.3
84.3
120
172
245
335
436
577
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
4.99
8.84
14.2
31.7
58.4
98.5
138
201
287
388
509
675
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
35.4
68.1
110
156
234
322
466
580
759
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.18
0.31
0.48
0.98
1.65
2.80
-
5.91
10.8
17.7
39.0
75.6
126
173
256
363
496
649
852
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.24
0.43
0.63
1.18
2.26
3.64
-
7.23
12.6
20.8
37.9
68.1
98.5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
REFERENCED WEIGHT LISTS
64
90 3DBW 90 3D Elbow
Referenced Weight Lists
kg
Nominal Size
DN NPS
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140 Sch160 XXS
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
-
-
-
-
-
-
-
-
-
-
-
35.1
55.0
78.5
125
164
208
309
374
446
694
806
927
1056
1194
1338
-
-
-
-
-
-
0.14
0.29
0.47
0.70
1.18
2.64
3.92
5.27
6.80
-
-
38.8
67.2
103
150
196
290
409
496
663
-
1004
1154
1315
1487
1667
-
-
-
-
-
-
0.17
0.33
0.56
0.80
1.43
2.83
4.47
6.26
8.47
14.3
22.3
44.8
79.4
117
150
196
249
309
374
446
523
608
699
796
899
1008
1124
1246
1374
1509
1649
1797
0.17
0.33
0.56
0.80
1.43
2.83
4.47
6.26
8.47
14.3
22.3
44.8
79.4
126
174
260
369
483
-
807
-
-
-
1445
1634
1993
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
56.0
107
172
234
337
488
653
852
1123
-
-
-
-
-
-
-
-
-
-
-
-
0.22
0.43
0.48
1.07
1.97
3.75
6.04
8.60
11.8
20.4
33.6
68.1
107
154
198
260
330
409
496
591
694
806
927
1056
1194
1338
1493
1655
1826
2006
2191
2388
0.22
0.43
0.73
1.07
1.97
3.75
6.04
8.60
11.8
20.4
33.6
68.1
126
209
292
429
604
819
1083
1397
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
80.0
151
252
359
517
734
1005
1307
1731
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
14.9
26.5
42.8
95.3
175
295
414
604
862
1163
1526
2023
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
106
204
329
468
702
968
1338
1740
2276
-
-
-
-
-
-
-
-
-
-
-
-
0.29
0.56
0.92
1.43
2.92
4.90
8.45
-
17.7
32.3
53.4
117
227
377
519
770
1089
1487
1947
2554
-
-
-
-
-
-
-
-
-
-
-
-
0.36
0.72
1.28
1.88
3.53
6.70
11.0
-
21.6
37.8
62.6
114
204
295
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
REFERENCED WEIGHT LISTS
65
BW Straight Tee
: DN1200 NPS 48 STD 9.53mm Note: the weight for the size more than DN1200(NPS48) is calculated onthe basis of thickness 9.53mm.
Referenced Weight Lists
kg
Nominal Size
DN NPS
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
1300
1400
1500
1600
1700
1800
1900
2000
Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140 Sch160 XXS
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
52
56
60
64
68
72
76
80
-
-
-
-
-
-
-
-
-
-
-
-
17.5
28.0
42.6
64.5
78.2
102
168
185
222
340
390
420
480
540
610
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.15
0.18
0.27
0.46
0.68
0.96
2.06
2.87
3.65
4.56
-
-
22.0
37.1
55.7
76.3
95.7
141
198
241
305
-
478
549
627
709
796
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.16
0.20
0.28
0.55
0.78
1.17
2.21
3.23
4.33
5.68
9.08
13.6
25.5
44.8
63.1
76.3
95.7
121
150
182
205
254
289
332
379
429
481
537
598
636
712
779
850
917
1065
1226
1398
1580
1740
1980
2290
0.16
0.20
0.28
0.55
0.78
1.17
2.21
3.23
4.33
5.68
9.08
13.6
25.5
44.8
68.1
88.7
126
179
235
-
340
-
-
-
631
714
872
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
31.8
59.2
93.0
119
164
237
317
414
516
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.20
0.30
0.45
0.70
1.25
1.61
2.92
4.42
5.95
7.88
12.9
20.5
38.7
59.2
83.2
101
126
160
190
241
272
337
383
441
503
569
639
713
791
846
946
995
1080
-
-
-
-
-
-
-
-
0.20
0.30
0.45
0.70
1.25
1.61
2.92
4.42
5.95
7.88
12.9
20.5
38.7
69.7
112
148
191
269
365
482
589
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
45.4
83.3
137
183
252
357
489
636
796
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10.0
16.8
26.1
54.1
96.6
160
211
294
419
566
743
930
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
60.4
113
178
238
342
471
651
846
1046
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.25
0.35
0.54
0.91
1.39
2.39
3.81
6.17
-
11.8
20.5
32.5
66.6
125
204
264
375
529
724
947
1174
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.35
0.45
0.77
1.26
1.83
2.89
5.21
8.01
-
14.5
24.0
38.1
64.6
113
160
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
REFERENCED WEIGHT LISTS
66
BW Straight Tee
: DN1200 NPS 48 STD 9.53mm Note: the weight for the size more than DN1200(NPS48) is calculated onthe basis of thickness 9.53mm.
Referenced Weight Lists
kg
Large EndNominal Size
DN NPS
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
1300
1400
1500
Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140 Sch160 XXS
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
52
56
60
-
-
-
-
-
-
-
-
-
-
-
5.57
8.18
11.1
24.6
30.5
36.8
65.5
72.2
78.9
136
147
157
168
179
189
-
-
-
-
-
-
-
-
-
0.06
0.12
0.16
0.25
0.37
0.79
0.97
1.28
1.45
-
-
6.16
9.99
14.6
29.5
36.5
51.3
86.7
95.6
117
-
183
196
209
223
236
-
-
-
-
-
-
-
-
-
0.07
0.14
0.19
0.29
0.46
0.85
1.11
1.52
1.81
3.04
4.35
7.12
11.8
16.5
29.6
36.6
44.1
65.5
72.2
78.9
103
111
119
127
135
143
151
159
167
175
213
222
241
259
278
0.07
0.14
0.19
0.29
0.46
0.85
1.11
1.52
1.81
3.04
4.35
7.12
11.8
17.8
34.3
48.3
65.3
102
-
143
-
-
-
230
245
282
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
8.88
16.0
24.3
46.0
62.7
86.2
138
164
199
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.09
0.18
0.25
0.38
0.63
1.12
1.50
2.09
2.51
4.33
6.55
10.8
16.0
21.8
39.0
48.3
58.3
86.7
95.6
105
136
147
158
168
179
190
200
211
222
232
283
296
-
-
-
0.09
0.18
0.25
0.38
0.63
1.12
1.50
2.09
2.51
4.33
6.55
10.8
18.8
29.5
57.4
79.7
107
174
209
247
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
12.7
22.5
35.7
70.8
96.2
130
213
252
306
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
3.18
5.63
8.35
15.1
26.0
41.7
81.5
112
152
247
294
358
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
16.9
30.4
46.5
92.0
130
171
284
336
402
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.12
0.24
0.32
0.51
0.93
1.46
2.09
-
3.76
6.86
10.4
18.6
33.7
53.3
102
143
193
316
376
452
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.15
0.31
0.45
0.70
1.20
2.00
2.71
-
4.60
8.02
12.2
18.0
30.4
41.7
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
REFERENCED WEIGHT LISTS
67
BW Cap
E Note: the weight for the above listed caps is calculated on the basis of Eheight.
Referenced Weight Lists
kg
Nominal Size
DN NPS
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140 Sch160 XXS
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
-
-
-
-
-
-
-
-
-
-
-
-
4.45
6.89
9.75
14.6
18.3
23.4
35.1
42.7
49.7
74.0
82.4
91.2
101
110
120
-
-
-
-
-
-
0.04
0.05
0.10
0.13
0.16
0.21
0.40
0.65
0.90
1.04
-
-
4.92
8.46
12.9
17.6
22.1
32.9
46.8
56.9
74.5
-
103
114
126
138
150
-
-
-
-
-
-
0.04
0.05
0.12
0.16
0.19
0.26
0.44
0.73
1.07
1.30
2.10
3.19
5.72
10.1
14.6
17.5
22.1
28.2
35.1
42.7
49.7
55.6
61.8
68.5
75.4
82.7
90.2
104
113
122
138
148
158
0.04
0.05
0.12
0.16
0.19
0.26
0.44
0.73
1.07
1.30
2.10
3.19
5.72
10.1
15.9
20.5
29.4
42.2
55.6
-
91.2
-
-
-
138
152
180
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
7.21
13.9
21.9
27.7
38.6
56.3
76.0
99.7
129
-
-
-
-
-
-
-
-
-
-
-
-
0.06
0.07
0.16
0.22
0.26
0.36
0.59
1.08
1.51
1.85
3.06
4.93
8.88
13.8
19.5
23.3
29.4
37.5
46.8
57.0
66.3
74.1
82.4
91.2
101
110
120
139
150
162
184
197
210
0.06
0.07
0.16
0.22
0.26
0.36
0.59
1.08
1.51
1.85
3.06
4.93
8.88
16.4
26.9
35.0
49.7
70.4
96.5
128
162
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10.6
19.8
32.9
43.8
60.7
86.8
120
157
203
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
2.40
4.07
6.41
12.8
23.3
39.0
51.1
71.7
103
141
185
240
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
14.5
27.6
43.9
58.4
84.6
117
164
214
273
-
-
-
-
-
-
-
-
-
-
-
-
0.08
0.11
0.22
0.28
0.36
0.57
0.80
1.48
-
2.91
5.09
8.20
16.1
31.0
51.2
65.7
93.8
134
184
242
311
-
-
-
-
-
-
-
-
-
-
-
-
0.11
0.15
0.32
0.43
0.52
0.73
1.18
2.02
-
3.69
6.10
9.86
15.6
27.6
39.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
REFERENCED WEIGHT LISTS
68
45BW Straight 45 Lateral Tee
Referenced Weight Lists
kg
Nominal Size
DN NPS
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
Sch10 Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
0.25
0.37
0.73
1.26
1.7
2.27
3.46
4.52
5.38
7.01
10.8
15.1
25.6
41.6
61.4
105
133
164
197
234
277
404
473
542
616
696
780
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
42.8
62.5
84.9
130
165
204
293
348
414
643
753
864
982
1110
1245
-
-
-
-
-
-
0.28
0.42
0.76
1.34
1.93
2.58
5.29
6.94
8.29
10.8
-
-
47.3
76.3
111
156
198
284
388
462
615
-
937
1076
1224
1383
1551
-
-
-
-
-
-
0.32
0.49
0.87
1.59
2.21
3.13
5.68
7.90
9.85
13.5
20.4
30.8
54.6
90.2
126
156
198
244
293
348
414
485
568
651
740
836
937
1073
1190
1313
1441
1575
1716
0.32
0.49
0.87
1.59
2.21
3.13
5.68
7.90
9.85
13.5
20.4
30.8
54.6
90.2
136
181
262
361
459
-
750
-
-
-
1344
1519
1854
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
68.2
122
186
242
340
477
620
794
1043
-
-
-
-
-
-
-
-
-
-
-
-
0.41
0.64
1.13
2.09
2.95
4.31
7.50
10.7
13.5
18.7
29.0
46.4
83.0
122
166
205
262
323
388
462
549
643
753
864
982
1110
1245
1425
1580
1744
1915
2093
2280
0.41
0.64
1.13
2.09
2.95
4.31
7.50
10.7
13.5
18.7
29.0
46.4
83.0
144
225
302
432
591
778
1009
1298
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
97.5
172
273
373
521
718
954
1218
1608
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
23.7
37.8
59.2
116
199
319
430
609
844
1105
1422
1879
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
130
232
355
485
707
947
1271
1621
2114
-
-
-
-
-
-
-
-
-
-
-
-
Sch160
0.49
0.85
1.47
2.62
3.95
6.41
9.81
14.9
-
28.1
46.0
73.7
143
258
408
539
776
1066
1413
1814
2372
-
-
-
-
-
-
-
-
-
-
-
-
XXS
0.64
1.07
1.89
3.63
5.21
7.75
13.4
19.4
-
34.4
53.8
86.5
139
232
319
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
REFERENCED WEIGHT LISTS
69
Lap Joint Stub End
Referenced Weight Lists
kg
Nominal Size
DN NPS
152025324050658090
100125150200250300350400450500550600
Sch10S Sch40S Sch80S
1/23/41
11/411/22
21/23
31/24568
1012141618202224
0.070.090.150.190.220.350.460.620.700.941.301.752.904.797.207.959.5011.114.116.519.8
0.090.120.250.340.390.710.951.221.361.592.803.304.958.5010.915.017.319.825.928.235.0
0.090.120.180.250.310.520.811.101.521.802.253.595.9810.214.915.818.922.024.3
-29.6
0.120.160.320.430.521.021.602.112.553.055.427.0210.618.422.828.733.138.042.3
-51.2
0.120.150.240.330.430.731.101.502.092.583.605.769.1813.719.521.625.229.332.6
-39.7
0.160.210.430.570.751.492.222.983.654.447.8611.316.224.930.238.644.551.156.8
-68.8
Long Pattern Short Pattern Short Pattern Long Pattern Short Pattern Long Pattern
kg
Large End Nominal Size
DN NPS
8
10
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
Sch10 Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120 Sch140
1/4
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
0.03
0.04
0.07
0.09
0.18
0.27
0.35
0.62
0.90
1.26
1.45
1.84
3.10
4.04
6.35
10.2
14.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
10.6
15.3
19.4
0.03
0.04
0.08
0.11
0.19
0.28
0.39
0.71
1.37
1.93
2.22
2.84
-
-
11.7
18.7
25.4
0.03
0.05
0.09
0.12
0.21
0.33
0.44
0.86
1.48
2.2
2.64
3.53
5.83
8.25
13.5
22.1
28.8
0.03
0.05
0.09
0.12
0.21
0.33
0.44
0.86
1.48
2.2
2.64
3.53
5.83
8.25
13.5
22.1
31.1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
16.8
29.8
42.5
0.04
0.07
0.11
0.16
0.28
0.44
0.59
1.19
1.95
2.98
3.63
4.91
8.29
12.4
20.5
29.8
38.0
0.04
0.07
0.11
0.16
0.28
0.44
0.59
1.19
1.95
2.98
3.63
4.91
8.29
12.4
20.5
35.1
51.5
-
-
-
-
-
-
-
-
-
-
-
-
-
-
24.1
42.0
62.3
-
-
-
-
-
-
-
-
-
-
-
6.23
10.8
15.8
28.7
48.6
72.8
-
-
-
-
-
-
-
-
-
-
-
-
-
-
32.0
56.7
81.1
Sch160
-
-
0.13
0.21
0.36
0.55
0.79
1.76
2.55
4.16
-
7.37
13.2
19.7
35.2
63.0
93.0
XX
-
-
0.17
0.27
0.47
0.76
1.05
2.13
3.48
5.39
-
9.02
15.4
23.1
34.2
56.7
72.8
Swaged Nipple
REFERENCED WEIGHT LISTS
70
Referenced Weight Lists
SW Tee & Cross kg
Nominal Size
DN NPS
68
101520253240506580
100
1/81/43/81/23/41
11/411/22
21/234
0.130.130.160.350.480.661.001.402.004.105.5515.6
0.220.220.450.550.901.461.902.803.70
---
---
1.151.802.253.954.878.89
---
0.150.150.190.460.590.811.191.672.594.957.2518.8
0.210.250.540.641.091.972.343.906.15
---
---
1.322.252.694.687.8410.5
---
3000 6000 9000
SW Tee SW Cross
3000 6000 9000
90 45SW 90 Elbow & 45 Elbow kg
Nominal Size
DN NPS
68
101520253240506580
100
1/81/43/81/23/41
11/411/22
21/234
0.090.090.120.260.350.520.851.051.752.804.609.60
0.150.150.320.400.651.251.402.352.96
---
---
0.851.482.202.903.504.35
---
0.080.080.120.220.280.550.710.891.302.684.908.80
0.160.160.280.300.720.901.151.902.95
---
---
0.781.251.852.623.455.80
---
3000 6000 9000
9 0SW 90 Elbow
4 5SW 45 Elbow
3000 6000 9000
SW Coupling & Cap kg
Nominal Size
DN NPS
68
101520253240506580
100
1/81/43/81/23/41
11/411/22
21/234
0.050.060.080.130.200.280.480.520.951.521.752.80
0.060.070.100.160.280.480.650.941.65
---
---
0.290.470.681.081.121.95
---
0.030.040.050.080.150.220.350.420.721.252.053.28
0.040.050.070.130.220.340.470.631.14
---
---
0.230.350.520.710.951.55
---
3000 6000 9000
SW Coupling SW Cap
3000 6000 9000
REFERENCED WEIGHT LISTS
71
Referenced Weight Lists
THRD Tee & Cross kg
Nominal Size
DN NPS
68
101520253240506580
100
1/81/43/81/23/41
11/411/22
21/234
0.130.130.160.350.450.661.001.402.204.206.1514.7
0.220.220.400.580.901.461.903.403.807.2010.717.9
0.350.570.661.151.802.253.954.878.8912.821.629.5
0.160.160.200.420.540.791.201.682.645.057.3817.6
0.260.260.480.701.081.752.284.084.668.6412.821.5
0.420.680.791.382.162.704.745.8510.715.426.535.4
2000 3000 6000
THRD Tee THRD Cross
2000 3000 6000
90 45HTRD 90 Elbow & 45 Elbow kg
Nominal Size
DN NPS
68
101520253240506580
100
1/81/43/81/23/41
11/411/22
21/234
0.080.080.130.220.320.500.800.931.602.955.6010.5
0.100.150.300.450.701.211.472.603.055.808.8514.9
0.180.330.480.721.291.652.703.906.059.8816.423.5
0.080.080.110.230.290.430.670.821.323.305.409.00
0.080.120.260.420.590.961.152.022.503.816.309.80
0.140.270.490.691.121.472.653.604.607.8113.117.0
2000 3000 6000
9 0THRD 90 Elbow
4 5THRD 45 Elbow
2000 3000 6000
THRD Coupling & Cap kg
Nominal Size
DN NPS
68
101520253240506580
100
1/81/43/81/23/41
11/411/22
21/234
0.060.080.110.220.300.550.861.261.653.004.257.80
0.090.130.240.400.521.061.322.203.374.817.2512.0
0.030.050.070.140.240.410.710.881.252.293.295.65
-0.110.170.290.420.760.961.422.243.805.439.26
3000 6000
THRD Coupling THRD Cap
3000 6000
REFERENCED WEIGHT LISTS
72
Referenced Weight Lists
Union & Hexagonal Nipple kg
Nominal Size
DN NPS
68
101520253240506580
1/81/43/81/23/41
11/411/22
21/23
0.250.300.350.460.610.851.351.922.854.907.10
0.020.030.050.100.130.220.340.470.691.352.03
0.020.040.060.120.170.290.410.580.911.692.55
3000
Union Hexagonal Nipple
Sch80 Sch160
Head Plug kg
Nominal Size
DN NPS
68
101520253240506580
100
1/81/43/81/23/41
11/411/22
21/234
0.010.020.030.060.100.180.300.410.671.111.693.48
0.020.030.050.080.140.250.490.651.161.832.925.50
0.020.050.080.120.200.340.590.731.442.363.506.08
Square Head Plug Hex Head Plug
Hex Head Bushing & Flush Bushing kg
Nominal Size
DN NPS
8101520253240506580
100
1/43/81/23/41
11/411/2
221/234
0.010.020.030.040.070.120.140.220.360.460.78
0.010.010.020.020.040.050.060.090.170.220.33
Hex Head Bushing Flush Bushing
Round Head Plug
REFERENCED WEIGHT LISTS
73
Referenced Weight Lists
Outlet kg
/Latrolet & Elbolet kg
Branch Nominal Size
DN NPS
15
20
25
32
40
50
65
80
100
150
200
250
300
1/2
3/4
1
11/4
11/2
2
21/2
3
4
6
8
10
12
Branch Nominal Size
DN NPS
6
8
10
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
600
1/8
1/4
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
24
0.04
0.04
0.06
0.11
0.16
0.32
0.38
0.57
0.85
1.28
1.88
2.20
2.80
5.70
7.20
10.8
17.0
25.6
27.0
36.0
48.2
58.5
149
0.05
0.05
0.07
0.13
0.18
0.34
0.42
0.60
0.90
1.35
2.00
2.40
3.20
6.80
11.0
19.2
19.5
29.6
32.0
41.7
55.8
76.0
152
-
-
-
0.18
0.20
0.40
0.50
0.70
1.10
2.00
3.20
-
6.00
9.80
16.0
31.0
-
-
-
-
-
-
-
0.05
0.05
0.09
0.16
0.20
0.42
0.59
0.70
1.10
1.40
2.30
-
4.20
-
-
-
-
-
-
-
-
-
-
-
-
-
0.35
0.47
0.68
1.10
1.30
2.45
-
-
-
-
-
-
-
-
-
-
-
-
-
-
0.05
0.05
0.09
0.17
0.22
0.43
0.61
0.69
1.10
1.52
2.50
-
4.10
-
-
-
-
-
-
-
-
-
-
STD XS Sch160
BW Outlet SW Outlet
3000 6000 3000
-
-
-
0.32
0.47
0.65
0.96
1.28
2.15
-
-
-
-
-
-
-
-
-
-
-
-
-
-
6000
THRD Outlet
0.25
0.40
0.73
1.10
1.47
2.50
3.20
6.05
10.5
23.6
32.9
58.5
86.0
0.28
0.42
0.77
1.15
1.60
2.60
3.40
6.35
11.8
33.5
50.3
76.5
112
0.38
0.61
1.10
1.41
2.35
3.35
3.70
7.20
13.6
38.0
-
-
-
0.32
0.54
0.93
1.32
1.59
3.06
-
-
-
-
-
-
-
STD XS
BW Latrolet & BW Elbolet SW/THRD Latrolet & Elbolet
Sch160 3000
0.48
0.81
1.20
2.23
3.12
4.95
-
-
-
-
-
-
-
REFERENCED WEIGHT LISTS
6000
74
(ASME B36.10M)Welded and Seamless Steel Pipe(ASME B36.10M)
Referenced Weight Lists
kg
Nominal Size
DN NPS
6
8
10
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
650
700
750
800
850
900
950
1000
1050
1100
1150
1200
OD Sch10 Sch20 Sch30 STD Sch40 Sch60 XS Sch80 Sch100 Sch120
1/8
1/4
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
10.3
13.7
17.1
21.3
26.7
33.4
42.2
48.3
60.3
73.0
88.9
101.6
114.3
141.3
168.3
219.1
273.0
323.9
355.6
406.4
457.0
508
559
610
660
711
762
813
864
914
965
1016
1067
1118
1168
1219
0.28
0.49
0.63
1.00
1.28
2.09
2.70
3.11
3.93
5.26
6.45
7.40
8.36
11.57
13.48
19.96
27.78
36.00
54.69
62.64
70.57
78.55
86.54
94.53
127.4
137.3
147.3
157.2
167.2
177.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
33.31
41.77
49.73
67.90
77.83
87.71
117.2
129.1
141.1
202.7
218.7
234.7
250.6
266.6
282.3
-
-
-
-
-
-
0.32
0.54
0.70
1.12
1.44
2.18
2.87
3.53
4.48
8.04
9.92
11.41
12.91
-
-
36.81
51.03
65.20
81.33
93.27
122.4
155.1
171.1
209.6
-
271.2
292.2
312.2
332.1
351.7
-
-
-
-
-
-
0.37
0.63
0.84
1.27
1.69
2.50
3.39
4.05
5.44
8.63
11.29
13.57
16.07
21.77
28.26
42.55
60.31
73.88
81.33
93.27
105.2
117.2
129.1
141.1
152.9
164.9
176.8
188.8
200.3
212.6
224.5
236.5
248.5
261.5
272.3
284.2
0.37
0.63
0.84
1.27
1.69
2.50
3.39
4.05
5.44
8.63
11.29
13.57
16.07
21.77
28.26
42.55
60.31
79.73
94.55
123.3
155.8
183.4
-
255.4
-
-
-
342.9
364.9
420.4
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
53.08
81.55
109.0
126.7
160.1
205.7
247.8
294.3
355.3
-
-
-
-
-
-
-
-
-
-
-
-
0.47
0.80
1.10
1.62
2.20
3.24
4.47
5.41
7.48
11.41
15.72
18.63
22.32
30.97
42.56
64.64
81.55
97.46
107.4
123.3
139.2
155.1
171.1
187.1
202.7
218.7
234.7
250.6
266.6
282.3
298.2
314.2
330.2
346.2
351.8
377.8
0.47
0.80
1.10
1.62
2.20
3.24
4.47
5.41
7.48
11.41
15.72
18.63
22.32
30.97
42.56
64.64
96.01
132.1
158.1
203.5
254.6
311.2
373.8
442.1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
75.92
114.8
159.9
195.0
245.6
309.6
381.5
451.4
547.7
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
28.32
40.28
54.20
90.44
133.1
187.0
224.7
286.7
363.6
441.5
527.0
640.0
-
-
-
-
-
-
-
-
-
-
-
-
Sch140
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
100.9
155.2
208.1
253.6
333.2
408.3
508.1
611.6
720.2
-
-
-
-
-
-
-
-
-
-
-
-
Sch160
-
-
-
1.95
1.90
4.24
5.16
7.25
11.11
14.92
21.35
-
33.54
49.11
67.56
111.3
172.3
238.8
281.7
365.4
459.4
564.8
672.3
808.2
-
-
-
-
-
-
-
-
-
-
-
-
XXS
-
-
-
2.55
3.64
5.45
7.77
9.56
13.44
20.39
27.68
-
41.03
57.43
79.22
107.9
155.2
187.0
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
, kg/mOD
REFERENCED WEIGHT LISTS
75
(ASME B36.19M)Stainless Steel Pipe(ASME B36.19M)
Referenced Weight Lists
kg
Nominal Size OD
DN NPS
6
8
10
15
20
25
32
40
50
65
80
90
100
125
150
200
250
300
350
400
450
500
550
600
750
OD T kg/m T kg/m T kg/m T kg/m
1/8
1/4
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
31/2
4
5
6
8
10
12
14
16
18
20
22
24
30
10.3
13.7
17.1
21.3
26.7
33.4
42.2
48.3
60.3
73.0
88.9
101.6
114.3
141.3
168.3
219.1
273.0
323.9
355.6
406.4
457.0
508
559
610
762
-
-
-
1.65
1.65
1.65
1.65
1.65
1.65
2.11
2.11
2.11
2.11
2.77
2.77
2.77
3.40
3.96
3.96
4.19
4.19
4.78
4.78
5.54
6.35
-
-
-
0.80
1.03
1.30
1.65
1.91
2.40
3.69
4.51
5.18
5.84
9.47
11.32
14.79
22.63
31.25
34.36
41.56
46.81
59.25
65.24
82.47
118.31
1.24
1.65
1.65
2.11
2.11
2.77
2.77
2.77
2.77
3.05
3.05
3.05
3.05
3.40
3.40
3.76
4.19
4.57
4.78
4.78
4.78
5.54
5.54
6.35
7.92
0.28
0.49
0.63
1.00
1.28
2.09
2.70
3.11
3.93
5.26
6.45
7.40
8.36
11.57
13.48
19.96
27.78
36.00
41.30
47.29
53.26
68.61
75.53
94.45
147.36
1.73
2.24
2.31
2.77
2.87
3.38
3.56
3.68
3.91
5.16
5.49
5.74
6.02
6.55
7.11
8.18
9.27
9.53
-
-
-
-
-
-
-
0.37
0.63
0.84
1.27
1.69
2.50
3.39
4.05
5.44
8.63
11.29
13.57
16.07
21.77
28.26
42.55
60.31
73.88
-
-
-
-
-
-
-
2.41
3.02
3.20
3.73
3.91
4.55
4.85
5.08
5.54
7.01
7.62
8.08
8.56
9.53
10.97
12.70
12.70
12.70
-
-
-
-
-
-
-
0.47
0.80
1.10
1.62
2.20
3.24
4.47
5.41
7.48
11.41
15.27
18.63
22.32
30.97
42.56
64.64
96.01
132.08
-
-
-
-
-
-
-
Sch5s Sch10s Sch40s Sch80s
REFERENCED WEIGHT LISTS
76
Calculation equation and conversion of unit
1)Equation for calculation the weight of steel pipes
W = 0.02466T (OD -T ):
where:W kg /m
pipe weight per meter kg/mT mm
thickness of the pipe mmOD , mm
outer diameter of the pipe mm
2) 9 0 /Equation for calculation the weight of 90 elbows
W = 9.685 10-6 R (OD2 -ID2 ):
whereW 90 / kg
weight of the elbow and/or bend kgR / mm
radius of the elbow and/or bend mmOD / mm
outer diameter of the elbow and/or bend mmID / mm
inter diameter of the elbow and/or bend mm
3) Conversion between units
length
area
volume
density
pressure
temperature
power
force
weight
1 mm = 0.03937 in
1 m = 3.2808 ft
1 cm2 = 0.155 in2
1 m2 = 10.764 ft2
1 cm3 = 0.061 in3
1 m3 = 35.315 ft3
1 kg = 2.2046 lb
1 kg/m3 = 0.0624 lb/ft3
1 MPa = 0.145 ksi = 145 psi
1 N = 0.225 lbf
1 J = 0.73756 ft lbf
n = 9/5 n + 32) F
1 in = 25.4 mm
1 ft = 12 in = 0.3048 m
1 in2 = 6.452 cm2
1 ft2 = 0.093 m2
1 in3 = 16.3871 cm3
1 ft3 = 0.0283 m3
1 lb = 0.4536 kg
1 lb/ft3 = 16.02 kg/m3
1 psi = 0.006895 MPa
1 lbf = 4.45 N
1 ft lbf = 1.35582 J
n F = 5/9 (n - 32)
CALCULATION EQUATION AND CONVERSION OF UNIT
77
NOTE
