LINIA Product Range Overview

8/9/2019 LINIA Product Range Overview

1/31

CLIP IN YOUR LINE

CONTINUOUS

LIGHTING SYSTEM


2/31

PictogramsPictograms are used in the catalogue pages containing product descriptions to provide

quick and simple information about luminaire characteristics, lamps used and so on. These

are explained below.

All catalogue documentation such as dimensions,

weights, illustrations and technical data have been care-

fully collated. Subject to error, as well as technical and

formal modifications.

The General Terms and Conditions are contained in the

relevant valid price lists.

IP20

Luminaires for indoor installation

Protection rating IP20

IP54 Protection rating IP54

Dust and splash proof

T26

Fluorescent lamp dia. 26

T16

Fluorescent lamp dia. 16

Suitable for furniture mounting

Energy saving product made of high-grade HR

(high-reflection) reflector material.


3/313

T16

T16

T26

System overview 32-35

Battens 36-37

Trunking 38-39

Trunking accessories 40-42

Gear trays 43-47

Gear tray-optical control combinations 48-51

Modules 52-54Optical control and accessories 55-69

Other photometric data 70-71

Special technical features of RIDI LINIA and RIDI LINIA T16 6-11

Components of a continuous lighting system 12-27

Planning 28-31

About RIDI LINIA & RIDI LINIA T16

RIDI LINIA, RIDI LINIA T16, RIDI LINIA DECO 4-5The RIDI LINIA product family

Products


Battens 76

Trunking 77-78

Trunking accessories 79-81

Gear tray 82-86

Gear tray-optical control combinations 87-88

Modules 89-91Optical control and accessories 92-107

Other photometric data 108

Products

About RIDI LINIA DECO


Batten 116-117

Gear tray 118-121

Connection and fixing accessories 122

Optical control und accessories 123-129

Representatives 130

Products

109-113


4/314

178 mm

139 mm

136 mm

110 mm

108 mm

108 mm

RIDI LINIA RIDI LINIA T16 RIDI LINIA DECO

RIDI LINIA product family encompasses 3 different continuous lighting

systems:

RIDI LINIA

Continuous lighting system for T26 lamps, now with NEW through

wiring profile. Extremely wide range of accessory components and

scope for combination.

RIDI LINIA T16

Continuous lighting system for T16 lamps, now with NEW through

wiring profile.

The RIDI LINIA T16 system is based on the same trunking cross-

section as RIDI LINIA, but all optical control components have been

optimized for T16 lamps with suitably small dimensions.

RIDI LINIA DECO

The RIDI LINIA DECO system is designed exclusively for use with

T16 lamps and makes an immediate impression due to its minimal

dimensions. Can be used as a single luminaire or part of a continu-

ous lighting system.

With a variety of finishes from the RIDI LINIA range, RIDI offers just

the right product to address every application need.

The RIDI LINIA

product family


5/315

Product features Decorative lighting system consisting of

single luminaires and continuous lighting

systems for ceiling and pendant mounting

Nominal wattage continuous lighting sys-

tem 1x28W, 1x54W, 1x35W, 1x49W,

1x80W, 2x28W, 2x54W, 2x35W, 2x49W

Only in protection rating IP20

For continuous modular lighting system

Extensive range of fixing accessories

Many varieties of optical controls

Luminaire colour white / silver (similar to

RAL 9006) For T16 lamps

Gear tray, reflectors made of galvanized,

painted sheet steel, colour white / silver

(similar to RAL 9006)

8-core through wiring 1.5 mm for additio-

nal control circuit or emergency lighting

Plug and socket system for simple electri-

cal connection of the through wiring

Use:

Decorative lighting for the retail trade, offices

and administration, schools.

Through wiring:8 x 1,5 mm2

Protection ratings:

IP20

Product features

Lighting system consisting of single lumi-

naires and continuous lighting systems for

ceiling and pendant mounting


tem 1x28W, 1x54W, 1x35W, 1x49W,

1x80W, 2x28W, 2x54W, 2x35W, 2x49W,

2x80W

Versions in protection rating IP20 / IP54

For modular and variable gear tray positio-

ning

Extensive fixing accessories


For T16 lamps

Colour white / silver (similar to RAL 9006)

Trunking, gear tray, reflectors made of

galvanized, painted sheet steel, Colour

white / silver (similar to RAL 9006)

5, 7 or 11-core through wiring with varia-

ble take-off

Length of the luminaire unit 1186/1486

mm

Use:

Commerce and industry, trade,offices and administration schools.

Through wiring:

5 x 2,5 mm2

5 x 2,5 mm2 & 2 x 1,5 mm2

5 x 2,5 mm2 & 6 x 1,5 mm2

Protection ratings:

IP20

IP54

IP54

Product features

Lighting system consisting of single lumi-

naires and continuous lighting systems for

ceiling and pendant mounting for T26

lamps


tem 1x36W, 2x36W, 1x58W, 2x58WVersions in protection rating IP20 / IP54

For modular and variable gear tray positio-

ning

Extensive fixing accessories


Colour white / silver (similar to RAL 9006)

Trunking, gear tray, reflectors made of

galvanized, painted sheet steel, colour

white / silver (similar to RAL 9006)

5, 7 or 11-core through wiring with varia-

ble take-off

Length of the luminaire unit 1237/1537

mm

Use:Commerce and industry, trade,

offices and administration schools.

Through wiring:

5 x 2,5 mm2

5 x 2,5 mm2 & 2 x 1,5 mm2

5 x 2,5 mm2 & 6 x 1,5 mm2

Protection ratings:

IP20IP54

IP54


6/316

Safe

& simple

Colour navigation from the pack through to

the individual components: the colour

coding system uses blue to denote 5-core,

purple for 7-core and green for 11-core

wiring. This easily recognizable system is

used consistently throughout all compo-

nents of the continuous lighting system.

Safety: The continuous lighting system is

earthed automatically by forced contacting

at the electrical components. The ends of

the through wiring profiles are closedusing patented protective caps.

Structure of the continuous lighting sys-

tem: Simple assignment of trunking and

connectors using the conductor colour

coding system. The gear trays are additio-

nally protected against inadvertent polarity

reversal during assembly by a mechanical

coding system.

Flexible

Reliable gear tray contacting is possible at

any position of the trunking along the con-

tinuous through wiring profile, permitting

the structure of the continuous lighting

system to be varied at will.

Alongside standard gear trays for T26 and

T16 lamps, new modules are now availa-

ble for flexible continuous lighting soluti-

ons. The range includes emergency

lighting modules with E27 lampholders aswell as LED illuminated signs, sockets,

trunking and facility for direct fixture of

spotlights.

All accessories for continuous lighting sys-

tem fixing can be clipped onto the trunking

without the aid of tools and variably dis-

placed in the lengthways direction.

The wide-ranging selection of optical con-

trols, including reflectors, louvres and pa-

nels, has the right solution to offer for

every lighting situation.

Energy efficient

The drive to reduce energy consumption, cut

damaging CO2 emissions and so reduce en-vironmental pollution is something which

concerns us all worldwide.

In lighting systems, this effect can only be

brought about by reducing energy consump-

tion, not by implementing lower connected

loads.

But at the same time, a lighting system has

to create an environment in which people

can work efficiently and feel comfortable.

In Germany, lighting accounts for around

12% of the total electrical energy expended.

The majority of installed lighting systems aremore than 15 years old, and lag considerably

behind the latest developments in energy ef-

ficiency.

If the lighting technology available today

were used comprehensively throughout the

country, in Germany the potential for savingswould be:

Offices: appr. 3.2 billion kWh

Industry, workshops: appr. 8.4 billion kWh

Roads: appr. 2.6 billion kWh

Private homes: appr. 7.5 billion kWh

In practical terms, this means that if modern

lighting systems were used, CO2 emissions

could be reduced by 13,000,000 metric tons

annually.

The new RIDI LINIA continuous lighting sys-tem with variable contacting permits savings

by ensuring that specified luminous intensity

levels are achieved with greater accuracy.

The distances between luminaires can be


7/317

Toolless: Simple assembly using the pro-

ven RIDI twist-lock catch at the gear tray.

This mechanism is used to fasten the gear

tray on the trunking and also as a fixture

for the optical control.

The phase selection and selection of

emergency lighting circuits takes place bythe simple displacement of contacts in the

plug housing of the gear tray.

Consistent colour coding for the through

wiring profile system

The gear trays in different lengths and wide se-

lection of modules can be used at any optional

position in the trunking.

chosen at will (see right). The open trunking

simply needs to be closed by a dummycover. At the same time, this solution helps

cut procurement costs.

The presence-controlled continuous lighting

system LINIA-I opens up additional potential

for ecological lighting and naturally for sa-

vings in terms of energy costs.

= Gear tray

= Dummy cover

Solution 1: gear tray 158 connected to gear tray 158:

104 luminaires in the room, mean luminous intensity Em 404 lx, total output 5,720 Watts

> Luminous intensity higher than recommended, high energy consumption,

high procurement costs

Example of a production hall, room length 40 m, width 25 m, height 4 m

Recommended mean luminous intensity Em 300 lx

Solution 2: tray 158 alternating with dummy cover 158:

52 luminaires in the room, mean luminous intensity Em 205 lx, total output 2,860 Watts

> Luminous intensity too low!

Solution 3: Solution 3: gear tray 158 with optimized flexible spacing,- NEW - trunking closed by dummy cover (shortened as required):

80 luminaires in the room, mean luminous intensity Em313 lx, total output 4,400 Watts> Recommended luminous intensity achieved, optimized energy consumption,lower procurement costs


8/318

BLUE = 5-core

Through wiring profile

Through wiring:

5 x 2,5 mm2

For three-phase wiring

with phase selection at the gear tray

PURPLE = 7-core

through wiring profile

Through wiring:

5 x 2.5 mm & 2 x 1.5 mm

For additional control cable

or emergency light

GREEN = 11-core

through wiring profile

Through wiring:

5 x 2.5 mm & 6 x 1.5 mmFor additional control cable

and two emergency light circuits

Raising the profile:

Through wiring with a difference

Trunking

Gea

rtray

Trunking

Geartray

Trun

king

Geartray


9/319

What works with which components?

Compatibility

Trunking VLT ... -5

compatible with

Gear tray

VLG ... -5

Trunking VLT ... -7

compatible with

Gear tray

VLG ... -5

VLG ... -7 ( facility for additional control cable

or emergency light)

Trunking VLT ... -11

compatible with

Gear tray

VLG ... -5

VLG ... -7 (facility for additional control cable

or emergency light)VLG ... -11 (facility for additional control cable

and two emergency light circuits)


10/3110

Splash water proof, dust proof and safe

Protection ratings IP20 and IP54

Seal VLTVD


11/3111

The mains supply can be fed at the ends of the continuous lighting system or at the butt joints between two trun-

king elements. A sleeve is used for this which completely surrounds the cable and so guarantees the IP54 rating.

Depending on what the room is used for, dif-

ferent demands are made on the luminaire

protection rating. The specifications for pro-

duction workshops differ considerably from

those for office spaces or classrooms.

Protection ratings:

IP20: Proof against the ingress of solid

foreign bodies larger than 12.5 mm

in size

IP54: Dust and splash water proof

The same trunking can be used with the RIDI

LINIA continuous lighting system to comply

with either the IP20 or IP54 protection ra-

tings. The required protection rating is achie-

ved by selecting the suitable gear tray series.

For IP20:

Use of gear tray series VLG ... and dummy

cover VLB ... (metal) / VLBK ... (plastic)

For IP54:

Use of gear tray series VLSG ... and dummy

cover VLSB ... (metal) / VLSBK ... (plastic)

Seal VLTVD has to be used at the trunking

connection. Dummy cover VLSBK ... (plastic)

for IP54 can be shortened by the user as re-

quired. Here, the seal VLSBKD is mounted at

the ends.

When using gear trays VLSG ... and dummy

cover VLSBK ... for IP54, the positive locking

fixture between the trunking and dummycover in the longitudinal direction eliminates

the need for any additional means of sealing.

This puts an end to the risk of seal ageing

and fatigue, and ensures that the luminaire

remains fully compliant with the protection

rating over its entire life.


12/3112

Stable basic continuous lighting system with new through wiring profile

RIDI LINIA trunking VLT ...

The profile and trunking can be shortened by a skilled workman on site.

NOTE: the protective cap must be replaced properly on the through wiring profile after cutting to size!

Observe the assembly instructions.

Cross section through the trunking

with through wiring profile


13/3113

The benefits of the VLT ... trunking with

through wiring profile:

Toolless assembly of trunking connector,

fixing accessories and terminals

Simple assignment trunking and trunking

connectors as well as electrical connector

blocks due to colour coding

Inscription on the mains connection is le-

gible from below for ease of assembly.

The mains connection is additionally iden-

tified by a mechanical coding system to

prevent inadvertent polarity reversal du-

ring assembly.

The continuous lighting system is earthed

automatically by forced contacting both at

the trunking connectors and the mains

connections.

There are two forms of mains connection

possible:

- at the face end through the knockouts in

the end cap

- from above through the knockouts at the

joints between two trunking elements

Reliable gear tray contacting is possible at

any position of the trunking along the con-tinuous through wiring profile, permitting

the structure of the continuous lighting

system to be varied at will.

The same trunking can be used in the RIDI

LINIA continuous lighting system for pro-

tection ratings IP20 and IP54. For IP54, the

seal VLTVD is additionally required.

The continuous lighting system is earthed automatically

by forced contacting

Connection to the power supply

With mains connection VLNE-... S for solid core conductors (rigid), 1.5 + 2.5 mm

With mains connection VLNE-... F for stranded conductors (flexible), 1.0 - 2.5 mm


14/3114

Trunking against trunking as far as the eye can see...

The trunking connector

Mechanical trunking connection:

Toolless plug-in connection by simply pushing the trunking elements together

Earthing through forced contactingPushingto

gether

Seal VLTVD


15/3115

Electrical trunking connection:

Clear coding of the through wiring profiles with continuous colour strips along the sides

The standard VLT ... trunking units are avai-

lable from 1186 mm (T16 1-length) up to

4611 mm (T26 3-length).

The trunking connector can be used to

create continuous lighting systems to any

optional length.

Mechanical connection takes place without

the need for tools by simply plugging toget-

her the components. This automatically

establishes the PE conductor connection.

To increase the mechanical strength of the

trunking joint, in addition to the internal con-

nector, the external trunking connector VLTVA

can also be used (exclusively for IP20 com-

pliance).

The electrical trunking connectors are also

colour coded to match the trunking ele-

ments, and are available in a 5-core (blue),

7-core (purple) and 11-core (green) version.

The through wiring profiles are connected

and automatically earthed by simply clipping

in the electrical connectors. The electrical

connector is reliably protected against inad-

vertent polarity reversal during assembly by

a mechanical coding system.

The colour coding of the through wiring pro-

files is continued in the electrical connector,

permitting fast, simple recognition of the

mounting direction. The visible continuous

colour strip allows the installer to instantly

monitor the safety and correctness of the in-

stallation.

The same trunking units are used for the

protection ratings IP20 and IP54. For IP54compliance, use of the seal VLTVD is requi-

red at the connection points.


16/31


17/3117

VLTW

Cable channel VLKL

Comprising VLKL clips and the relevant profiles in plas-

tic. Suitable for laying in additional cables or for cove-

ring fixing elements. Toolless mounting at the side is

also possible subsequent to installation.

Distance between fixing points with vertical suspension

All fixing clips can be clipped onto the trun-

king without the use of tools and variably

displaced in the lengthways direction, per-

mitted dimensionally flexible suspension of

the trunking.

Whether tube pendant, wire or chain sus-

pension, the wide range of RIDI LINIA acces-

sories offers the right solution every time.

Examples:

With the VLTHA, the height can be preci-

sely adjusted to the millimetre using a

threaded nut

With the VLTKS, the continuous lighting

system can be suspended at an incline

using chains of different lengths. VLTHT can be clipped directly onto the T-

profile of the room ceiling.

VLTHP is designed for direct fixture on a

tube pendant.

Using VLTLA and VLKL, additional con-

ductors can be guided along the length of

the continuous lighting system.

The spacing between fixing points depends

on the configuration / weight of the continu-

ous lighting system.

The maximum spacing is 3 m for exposed

operation with vertical suspension. Distances

of up to 5 m are possible with an M sus-

pension arrangement (see sketch).

Distance between fixing points with M suspension arrangement


18/3118

Straight on is not the only way!

Junction UKN ...

Junction application examples


19/3119

Mounting universal junction UKN

The universal junction does not contain any

luminaire adapters. the universal junction

does not come with a luminaire adapter.

These must be ordered separately depending

on the luminaire and the required number.

The connector blocks for the mains con-

nection are contained in the universal

junction kit.

The maximum through wiring possible

through junctions is 7 x 2.5 mm, and is con-

tained in the adapter.

Junctions can be used to create a wide va-

riety of geometrical patterns. The adjustable

angle of between two mounted luminaires is

limited between a minimum of 60 and a

maximum of 300 (exception: VLRML). Bet-

ween these angles, the two luminaires can

be arranged at any infinitely variable angle

relative to each other.

For fixing junctions to the ceiling, there are

three types of pendant fixing kits available:

UKNS

Wire suspension with metal ceiling fixtures

UKNSB

Wire suspension with canopy

UKNR-VL 050

Tube pendant with canopy, length 0.5 mUKNR-VL 100

Tube pendant with canopy, length 1.0 m

UKND

Ceiling fixture

First fix the universal junction point to the

ceiling with the selected fixing kit. Fasten

the luminaire adapter to the face end of the

luminaire and mount the through wiring

supplied with the luminaire adapter

(max. 7 x 2.5 mm). Then suspend the

luminaire with the adapter in the universal

junction point and tighten the lockingscrew. The electrical connection is then

made and the universal junction closed

with the two end caps. For precise instruc-

tions on mounting the junction points, see

the mounting instructions.

Universal junction UKN, adapter UKNA-VLT and fixing

accessories UKNS (wire pendant with ceiling fixture),

UKNSB (wire pendant with canopy), UKNR-VL

(tube pendant)


20/3120

For clip fixing at any optional position on the trunking

RIDI LINIA gear tray VLG ...

The flexibility of the system permits the gear trays to be mounted in any position in the trunking. If it should hap-

pen that the power take-off of the gear tray coincides during assembly with a trunking joint (here there is an elect-

rical connection block instead of the through wiring profile), the power take-off can be removed, turned 180 and

plugged back on again. The gear tray can then be turned 180 and mounted in the trunking. Consequently power

take-off takes place at a different location, without compromising flexibility.

Remove the power take-off turn 180 and replace.

As shown on the picture, the mechanical coding on the

power take-off / gear tray prevents inadvertent polarity

reversal.


21/3121

Contacting the power take-off at the through wiring pro-

file (for the sake of clarity, only the power take-off is

shown here, not the complete gear tray)

The power pick-up also has a contact at the side for au-

tomatic earthing.

The gear tray and the many modules can be positioned in any optional location in the trunking.

The RIDI LINIA series gear trays are designed

for T26 lamps.

Model designation e.g.

VLG 158-5 = 1-lamp gear tray for T26 lamp

in 58 watt, 5-core version (blue)

T15 lamps are used in the RIDI LINIA T16

series.

Model designation e.g.

VLG-T16 280-7 = 2-lamp gear tray for T16

lamp in 80 watt, 7-core version (purple)

The gear tray is still fixed in the trunking wit-

hout tools using the proven RIDI twist-lock

catch.

The plastic coated toggle with metal core

provides a reliable hold even in case of fire.

The gear trays can be mounted any optional

distance apart in any required position in the

trunking. The gaps created in-between can

be completely closed using a dummy cover.

The RIDI LINIA gear tray comes in the

following standard versions:

VLG ... for protection rating IP20

VLG-I ... for protection rating IP20

with movement sensor VLSG ... for protection rating IP54 VLSG ... FF for protection rating IP54

with protection tube

VLSG ... SRD for protection rating IP54

with triangular protection tube

VLSGR ... for protection rating IP54

with reflector and panel

The gear trays are offered in three different

versions:

... -5:

5-core with blue colour coding

for mounting in VLT-5, VLT-7 or VLT-11 ... -7:

7-core with purple colour coding

for mounting in VLT-7 or VLT-11 ... -11:

11- core with green colour coding

for mounting in VLT-11

Phase selection by displacing the contact

Standard setting = L2

Displacement is possible to the left for L1

or to the right for L3

In the 11-core version, the emergency lighting circuit

can additionally be selected by displacing the contacts.


22/3122

The intelligent gear tray for presence-controlled light

RIDI LINIA VLG-I

The standard sensor

Reliable detection of persons in a range of 4m x 6m

around the sensor with a mounting height of 3.5

to max. 5 m.

Pick-up range: For the size of the sensor, optimum den-

sity of pick-up fields.

The intelligent continuous lighting system

with integrated presence sensor provides

light only where it is required. The tray is

mounted on standard trunking. Retrofitting

on already installed systems is easily perfor-

med by simply exchanging the gear tray

(plug & play solution).

The system can be operated without the

need for programming and without an addi-

tional control cable. Special EVG-DALI bal-

lasts with warm start and automatic

switch-off function are used. Optimized

power loss.


23/3123

The 10m sensor

Reliable detection of persons in a range of 6m x 8m

around he sensor with a mounting height of max. 10 m.

Pick-up range: Due to the mounting height and the con-

figuration of prisms, the distances between pick-up

fields are greater.

The default starting time for the lamp is 0.7

seconds. If no further persons are detected

in the pick-up range of the sensor for a pe-

riod of 5 minutes, gradual switch-off the

lamp begins. The number of switching cycles

(> 300,000) does not influence the service

life of the lamp.

If the luminaire is mounted at a height of 3.5

m, approaching persons are picked up reli-

ably in an area measuring 4 m x 6m around

the sensor. For mounting heights above 5 m

to max. 10 m, a special sensor is required.

When the lamp is switched off, the power

consumption of the sensor unit is 0.5 W.

The system can theoretically be used in any

type of environment. It should be noted that

any potential savings are reduced as the

number of persons present increases. Parti-

cularly suitable applications include corri-

dors, common rooms and temporarilymanned workstations or offices.

Savings in terms of electrical energy

To verify the possible energy savings, four

systems were installed and monitored in in-

dustrial plants.

In the first location, 75 LINIA continuous

lighting units were installed in the roadway,

assembly line and common room. After two

months, on average 42% energy savings

were achieved.

At the second location, installation took place

in the logistics area. The savings achieved

here in an approximately 6-month period

amounted to 47%.

In the third location, 45 LINIA continuous 2-

lamp lighting units were used to illuminate

special test stations, resulting in energy sa-

vings of 47%.

The fourth location involved installation in

part of an open-plan office. This test was

performed using an existing recessed lumi-

naire fitted with 1 x 58 W lamp and matt lou-

vre. The existing luminaires were equipped

with a standard presence sensor and the

EVG-DALI ballast. This test has been running

for one year and has indicated energy sa-

vings of 52 %.

TO SUMMARIZE:

Depending on the varying presence ofpersonnel, savings of between

120 kwh 250 kwh can be achieved.

The use of presence sensors ensures that

the lighting is only operational when there

are people present. The combination of sen-

sor and EVG ballast works independently of

programming or addressing (plug & play).

Every unit of the LINIA system is fitted with a

presence sensor which switches on the lamp

when there is a person present and switches

it off again after 5 minutes without detecting

any presence. If a further persons enters the

sensor range during the switch-off delay,

this period is started again from zero, i.e. the

luminaire is switched on again for at least a

further 5 minutes.

t

Luminous

flux

100%

10%

0,7 s 24 s 17 s5 min

First

movement

Max. luminous

flux

Last

movement

Dimming

starts

Min. luminous

flux

Lamp is

switched off


24/3124

The right element for every requirement

RIDI LINIA modules VLM ...

VLM-SD 300 ...

To accommodate RIDI spotlights.

5-core version, blue colour coding,

for mounting in VLT-5, VLT-7 or VLT-11

VLM-STS 600 ...

With 3-phase trunking, phase selection

at the spotlight adapter.



VLM-ST 300 ...

With integrated PE socket




25/3125

Module types:

Emergency lighting module with lamphol-

der E14 or E27

Emergency lighting module for compact

lamp TC 5 to 11 Watt Emergency lighting module with sign Module for direct fixture of a spotlight from

the RIDI range

Module with trunking

Module with socket

The modules and gear tray can be freely

combined in a continuous lighting system

depending on requirements.

The spaces created as a result can be com-

pletely closed using a dummy cover. Dummy cover VLB made of sectional sheet

steel with same twist-lock catch as the

VLG for fixing optical controls

Dummy cover VLBK made of plastic, clips

into the trunking using projecting catches,

for optional shortening on site.

The RIDI LINIA modules are produced on the

basis of gear tray VLG. Because they use the

same cross-section and fixture method, they

can be used at any optional location in the

trunking VLT. Electrical contacting uses the

same plug contacts as for VLG.

VLM-E14 300 ...

Emergency lighting module with E14 lampholder.

7-core version, purple colour coding,


11-core version, green colour coding,

for mounting in VLT-11 for selection of two separate

emergency lighting circuits

VLM-E27 300 ...

Emergency lighting module with E27 lampholder.




for mounting in VLT-11 for selection of two separate


VLM-K11 600 ...

Emergency lighting module for compact fluorescent

lamp TC5 up to 11 Watt.




for mounting in VLT- for selection of two separate


VLM-LED-HW ...

Emergency lighting module with emergency exit sign




for mounting in VLT- for selection of two separate



26/3126

Unlimited versatility and scope for combination

RIDI LINIA optical control

Reflector connector VLRV

Is clipped in without using tools for even alignment of

the reflector at the butt joints.


27/3127

Simple fixture of the reflector takes place at the

twist lock catches on the gear tray.

Louvres and panels can be combined

with a wide range of reflectors from

the product selection to achieve

certain photometric or aesthetic ef-

fects.

The product pages contain a

pictogram alongside each reflector

(similar to the drawing on the right)

which indicates other combination

possibilities.

The industry reflectors made of matt

anodized super-purity aluminium are

specialists in ensuring maximum efficiency,

with an LOR of 90 - 100%. They are avai-

lable in a wide, narrow or inclined beam light

distribution version.

All reflectors can be mounted without tools

using the proven RIDI twist-lock catch.

The wide selection of products available for

the RIDI LINIA continuous lighting system of-

fers just the right solution no matter what

the requirement: reflectors, louvres and pa-

nels selectively direct the light without

dazzle or glare.

Additional aluminium reflectors can be inser-

ted in the VLR... reflector series. These im-

pact on the optical control in different ways

(wide, narrow and inclined beam light distri-

bution).

Reflector divider VLRZW

Clips into the reflector connectors in continuous lighting

systems RIDI LINIA (T26).

Serves as an optical divider of the continuous lighting

system and to improve longitudinal glare.

Trunking

Gear tray

Batten

Optical control/reflector

Lay-in reflector

Lay-in louvre / panel


28/3128

What can be done with 5, 7 or 11-core through wiring?

Continuous lighting system planning

RIDI continuous lighting system Expert

The Continuous Lighting System Expert is the ideal tool for simple, convenient combination

of continuous lighting systems and their various components. The necessary PC softwarecan be downloaded from www.ridi.de.

The user is guided by an easy-to-use menu prompting system to make all the necessary in-

puts. The software produces a parts list containing all the necessary components and cal-

culates the gross prices.

Pin assignment at the mains connection in the trunking Pin assignment at the adapter in the gear tray

Neutral

Three phase wiring

Phases

PE cable PE cable

Neutral

Three phase wiring:

phase selection

using sliding contacts

PE cable

Neutral

Three phase wiring:

phase selection


Dimmer cable 1 or

Emergency light phase L

Dimmer cable 2 or

Emergency light neutral N

PE cable

Neutral

Three phase wiring:

phase selection


Dimmer cable 1

Dimmer cable 2


Circuit 1 or 2 using sliding contacts

Emergency light neutral NCircuit 1 or 2 using sliding contacts

PE cable

Neutral

Three phase wiring

Phases

Dimmer cable 1 or


PE cable

Dimmer cable 2 or

Emergency light neutral N

PE cable

Neutral

Three phase wiring

Phases

Dimmer cable 1

PE cable

Dimmer cable 2

Emergency lighting circuit 1 phase L

Emergency lighting circuit 2 phase L

Emergency lighting circuit 1 neutral N

Emergency lighting circuit 2 neutral N

PE cable

5-core

7-core

11-core


29/3129

Example 1

Continuous lighting system fully fitted with lamps.

In the simplest application, the gear tray and optical control must be selected in accordance with the continuous lighting system length.

e.g. VLG 158-5

Example 2

Continuous lighting system alternately fitted with gear tray + optical control and dummy units VLB

e.g. VLG 158-5

e.g. VLB ...

e.g. VLBK ...

with adjusted length

e.g. VLM ... STS module with

trunking and spotlight

e.g. VLBK ...


Example 3

Continuous lighting system flexibly fitted with gear tray + optical control.

In this application, the intermediate spaces have to be completely closed using the plastic dummy cover VLBK

which is cut to length on site.

e.g. VLG 158-5

Example 4

Continuous lighting system flexibly fitted with gear tray, optical control and module inserts.



e.g. VLG 158-5

Planning basis:

BLUE system = 5-core through wiring5 x 2.5 mm (16A)

Use:

For standard continuous lighting systems with 3-core load distribution L1, L2, L3.

Phase selection takes place at the adapter using sliding contacts.

Trunking, 9-length, e.g. VLT ... -5




TrunkingPhase selection at the adapter


30/3130

Example 1

Continuous lighting system fully fitted with lamps in a dimmable version.


e.g. VLG 158-7 DALI

Example 2

Continuous lighting system fully fitted with lamps in a conjunction with emergency lighting inserts.


e.g. VLG 158-5 e.g. VLG 158-7 EVG-ED1

e.g. VLBK ...


e.g. VLM ... HW emergency sign/

emergency light module

e.g. VLBK ...


Example 3

Continuous lighting system flexibly fitted with lamps in a dimmable version.



e.g. VLG 158-7 DALI

Example 4

Continuous lighting system flexibly fitted with gear tray and emergency lighting module inserts.



e.g. VLG 158-5

TrunkingPhase selection at the adapter

Planning basis:

PURPLE system = 7-core through wiring5 x 2,5 mm (16A)

2 x 1,5 mm (10A)

Use:

For continuous lighting systems with 3-core load distribution in dimmable version

or in conjunction with emergency lighting inserts.






31/31

Example 1

Continuous lighting system fully fitted with lamps in a dimmable version and additionally one adjustable emergency lighting circuit.

e.g. VLG 158-7 DALI e.g. VLG 158-11 DALI-ED1

Example 2

Continuous lighting system flexibly fitted with lamps in a dimmable version and additionally one emergency lighting circuit.



e.g. VLG 158-7 DALI e.g. VLG 158-11 DALI-ED1

e.g. VLBK ...


e.g. VLBK ...


e.g. VLG 158-11 DALI-ED1

Circuit 1


Circuit 2

e.g. VLM ... STS module with

trunking and spotlight


Circuit 1

Example 3

Continuous lighting system flexibly fitted with lamps in a dimmable version and additionally two emergency lighting circuits.



e.g. VLG 158-7 DALI

Example 4

Continuous lighting system flexibly fitted with lamps in a dimmable version, two emergency lighting circuits and module inserts.



e g VLG 158 7 DALI

Phase selection at the adapter Selection of emergency

lighting circuits

e.g. VLBK ...


e.g. VLM ... HW emergency sign/

emergency light module

Trunking

Planning basis:

GREEN system = 11-core through wiring5 x 2,5 mm (16A)

2 x 1,5 mm (10A)

4 x 1,5 mm (10A)

Use:

For continuous lighting systems with 3-core load distribution

in dimmable version and additionally 2 independentemergency lighting circuits.

Selection by means of sliding contacts.





Date post:	30-May-2018
Category:	Documents
Upload:	james3783
View:	215 times
Download:	0 times

LINIA Product Range Overview

Documents