MS1442H & MS1455H Spreader OM Manual - John...

HSMFG0406 Rev. 3 5HPOMSP8

MANURE SPREADERO P E R A T O R ’ S M A N U A L

MS1442HMS1455H

TABLE OF CONTENTS

TABLE OF CONTENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . INSIDE COVER

WARRANTY & NOTES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

DEALER PRE-DELIVERY & DELIVERY CHECKLIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

BOLT TORQUE CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

BE ALERT SYMBOL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

SAFETY RULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9

DANGER - WARNING DECALS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-12

OPERATION MS1442H & MS1455H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14

ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

BEATERS REMOVAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

LUBRICATION GUIDE MS1442H & MS1455H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-19

DECAL LOCATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20-21

TROUBLE SHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

OPTIONAL EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

ORDERING PARTS - ABOUT IMPROVEMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

PARTS LISTS & DIAGRAMS MS1442H & MS1455H. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-46

OPTIONAL REAR PAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

SERVICE RECORDS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

-1-

NOTES

WARRANTY:Warranty coverage is provided by John Deere according to the terms of theAgricultural/Commercial & Consumer Equipment Warranty Statement. Carefully read thewarranty statement on the back of your original purchase order for details on coverageand limitations of this warranty.

AFTER COMPLETION, DEALER SHOULD REMOVE AND RETAIN FOR RECORDS

FRONTIERDEALER PRE-DELIVERY CHECK LIST

After the Manure Spreader has been completely set-up, check to be certain it is in correct running order beforedelivering to the customer. The following is a list of points to inspect. Check off each item as you have madethe proper adjustments and found the item operating satisfactorily.

PTO shields turn freely.All Shields and Guards are in place and fastened.All grease fittings have been lubricated and gearbox filled to proper level -See lubrication guide in this manual.All mechanisms are operating trouble free.All roller chains are at proper tension.All bolts and fasteners are tight.All decals are in place and legible.

Serial Number

(Dealer’s Name) Model Number

(Signature of Pre-Delivery Inspector) (Inspection Date)

DEALER DELIVERY CHECK LIST

This check list that follows is an important reminder of valuable information that should be passed on to thecustomer at the time this Manure Spreader is delivered.

Check off each item as you explain it to the customer.

This delivery check list, when properly filled out and signed assures the customer that the Pre-deliveryservice was satisfactorily performed.

Explain to the customer that the pre-delivery inspection was made.Explain to the customer all the safety precautions they must excercise when operating this unit.Explain recommended loads for different types of materials.Explain to customer that regular lubrication is required for proper operation and long life ofmachine. Show customer the lubrication section of Operators Manual.Give the customer Operators Manual and make sure he reads and understands all operatingand service instructions.Record Serial Number on page 23 of this Manual.

Date Delivered Dealer’s Name

By

Signature of Original Buyer

-3-

!

!!

!!

!

!

!

!

!!!!

FRONTIER MODEL MS1442H & MS1455HMANURE SPREADER

Your Frontier spreader has been manufactured of the finest quality materials andcomponents. The performance you get from your machine is largely dependent upon howwell you read and understand this manual and apply this knowledge. There is a right and awrong way to do everything. Please do not assume that you know how to operate andmaintain your spreader before reading this manual carefully. Keep this manual available forready reference.

S P E C I F I C A T I O N S

MS1442H MS1455H MS1442H MS1455H

-5-

Capacity (Old Rating). . . . . . . . . . . . . . . . . . . 425 Bu. . . . . . 550 Bu. . . . . . 425 Bu. . . . . . 550 Bu.Capacity Cu. Ft. Struck Level. . . . . . . . . . . . . 270. . . . . . . . . 430. . . . . . . . . 270. . . . . . . . . 430Side Loading Height. . . . . . . . . . . . . . . . . . . . 61-1/4” . . . . . . 81”. . . . . . . . . 61-1/4”. . . . . . 81”Overall Height Top of 2nd Beater or Vertical. . 74-3/4” . . . . . . 86-3/4”. . . . . . N/A. . . . . . . . . 121-1/2”Height-Top of Hyd. Endgate w/o Hook. . . . . . . 65”. . . . . . . . . 85-1/2”. . . . . . 65”. . . . . . . . . 85-1/2”Height-Top of Screen (Vertical Beater Only). . N/A . . . . . . . . . N/A. . . . . . . . . N/A. . . . . . . . . 117”Inside Width. . . . . . . . . . . . . . . . . . . . . . . . . . 72”. . . . . . . . . 72”. . . . . . . . . 72”. . . . . . . . . 72”Inside Length. . . . . . . . . . . . . . . . . . . . . . . . . 16’. . . . . . . . . .16’. . . . . . . . . .16’. . . . . . . . . .16’Inside Depth. . . . . . . . . . . . . . . . . . . . . . . . . . 34”. . . . . . . . . 53”. . . . . . . . . 34”. . . . . . . . . 53”Overall Width w/Tires. . . . . . . . . . . . . . . . . . . 10’2”. . . . . . . . 10’2”. . . . . . . . 10’2”. . . . . . . . 10’2”Overall Length. . . . . . . . . . . . . . . . . . . . . . . . 26’5”. . . . . . . . 26’5”. . . . . . . . 27’5”. . . . . . . . 27’5”Lower Horizontal Beater Diameter. . . . . . . . . 29”. . . . . . . . . 29”. . . . . . . . . N/A. . . . . . . . . N/AUpper Horizontal Beater Diameter. . . . . . . . . 20”. . . . . . . . . 29”. . . . . . . . . N/A. . . . . . . . . N/AVertical Beater Diameter. . . . . . . . . . . . . . . . N/A. . . . . . . . . N/A. . . . . . . . . 34”. . . . . . . . . 34”Hydraulic Push Unload Rate @ 15 GPM. . . . 31 Sec. . . . . . 52 Sec. . . . . . 31 Sec. . . . . . 52 Sec.Hydraulic Push Cylinder Diameter. . . . . . . . . 3-1/2”. . . . . . . 4-1/2”. . . . . . . 3-1/2”. . . . . . . 4-1/2”Spindle Size. . . . . . . . . . . . . . . . . . . . . . . . . . 3”. . . . . . . . . . 3”. . . . . . . . . . 3”. . . . . . . . . . 3”Hubs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bolt. . . . . . . 10 Bolt. . . . . . 8 Bolt. . . . . . . 10 BoltTire Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385 x 22.5. . . 425 x 22.5. . . . 385 x 22.5. . . . 425 x 22.5Wood Side Rails. . . . . . . . . . . . . . . . . . . . . . Standard. . . . . Standard. . . . . Standard. . . . . StandardStandard PTO. . . . . . . . . . . . . . . . . . . . . . . . 540 RPM. . . . . 1000 RPM. . . . 540 RPM. . . . . 1000 RPMOptional PTO. . . . . . . . . . . . . . . . . . . . . . . . . 1000 RPM. . . . 1-3/4” 1000. . . 1000 RPM. . . . 1-3/4” 1000Hydraulic Endgate. . . . . . . . . . . . . . . . . . . . . Standard. . . . . Standard. . . . . Standard. . . . . StandardSemi Liquid Rear Pan. . . . . . . . . . . . . . . . . . Optional. . . . . Optional. . . . . Standard. . . . . StandardWeight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7000#. . . . . . . 9680#. . . . . . . N/A. . . . . . . . . 11,000# ApproxNote: Determine right and left side of spreader by viewing it from the rear. If instructions or partslists call for hardened bolts see page 6 to identify.

HORIZONTIAL BEATERS VERTICAL BEATERS

-6-

BEALERT! YOUR SAFETY

IS INVOLVED.

THIS SYMBOL IS USED THROUGHOUT THIS BOOK WHENEVER YOUR PERSONAL SAFETY ISINVOLVED. TAKE TIME TO BE CAREFUL. REMEMBER: THE CAREFUL OPERATOR IS THE BESTOPERATOR. MOST ACCIDENTS ARE CAUSED BY HUMAN ERROR. CERTAIN PRECAUTIONSMUST BE OBSERVED TO PREVENT THE POSSIBILITY OF INJURY OR DAMAGE.

TRACTORSThis operator’s manual uses the term “Tractor” when identifying the power or the towing source.

-7-

RECOGNIZE SAFETY INFORMATION

This is the safety-alert symbol. When you see this symbolon your machine or in this manual, be alert to the potentialfor personal injury.

Follow recommended precautions and safe operatingpractices.

UNDERSTAND SIGNAL WORDS

A signal word- DANGER, WARNING, or CAUTION - isused with the safety-alert symbol.DANGER identifies themost serious hazards.

Safety signs with signal word DANGER or WARNING aretypically near specific hazards.

General precautions are listed on CAUTION safety signs.

-8-

FOLLOW SAFETY INSTRUCTIONS

Carefully read all safety messages in this manual,and all safety signs on your machine. Follow allrecommended precautions and safe operatingprocedures.

Keep signs in good condition. Immediately replaceany missing or damaged signs.

OBSERVE MAXIMUM TRANSPORT SPEED

The maximum transport speed for thisimplement is 32 km/h (20 mph).

Some tractors are capable of operating at speeds that exceedthe maximum transport speed of this implement. Regardless ofthe maximum speed capability of the tractor being used to towthis implement, do not exceed the implement’s maximumtransport speed.

Exceeding the implements maximum transport speed can result in:" Loss of control of the tractor/implement combination" Reduced or no ability to stop during braking" Implement tire failure" Damage to the implement structure or its components

Use additional caution and reduce speed when towing underadverse surface conditions, when turning, and when on inclines.

Do not attempt transport if the fully loaded implement weighs morethan 1.5 times the weight of the tractor.

TRACTORSThis operators manual uses the term “Tractor” when identifying the power or the towing source.

W A R N I N GTO PREVENT SERIOUS INJURY OR DEATH

Study The Above Safety RulesATTENTION - BE ALERT - YOUR SAFETY IS INVOLVED

BEFORE YOU ATTEMPT TO OPERATE THIS EQUIPMENT, READ AND STUDY THE FOLLOWINGINFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKSWITH THIS EQUIPMENT, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESESAFETY PRECAUTIONS.KNOW HOW TO STOP UNLOADING MECHANISM BEFORE STARTING IT.

If the machine becomes clogged, disengage the PTO. Stop the tractor engine, remove ignition key,and allow all mechanisms to stop before cleaning or working on the machine.Never allow riders in or on the machine.

Frontier always takes the operator and his safety into consideration and guards exposed movingparts for his protection. However, some areas cannot be guarded or shielded in order to assure properoperation. In addition, the operators manual and decals on the machine itself warn you of furtherdanger and should be read and observed closely.

-9-

hooked up.

DO NOT get off the tractor while the spreader is in operation.

DO NOT attempt to perform maintenance or repair with tractor running and PTO and hydraulic hoses

DO NOT step up on machine at any time.

NEVER manually feed material into the beaters.

DO NOT allow minors to operate or be near the machine.

DO NOT ALLOW PERSONNEL OTHER THAN THE QUALIFIED OPERATOR NEAR THE MACHINE.

Before starting tractor, be sure PTO shields turn freely and PTO is securely locked to tractor.

DO NOT clean, adjust, or lubricate the machine when any part is in operation.

Keep hands, feet, and clothing away from beaters when they are revolving.

Loose or floppy clothing should not be worn by the operator.

Be sure the machine is clear of people, tools, and other objects before engaging PTO.

DO NOT step over power take off shaft. Stay clear of PTO at all times.

NEVER start manure spreader until all guards and safety shields are secured in place.

NEVER operate spreader with a PTO speed Greater Than Recommended PTO RPM.

Stay clear of Hydraulic Lines. They may be under extreme pressure or heat.

-10-

-11-

-12-

1. Check for proper assembly and adjustment and make sure that all bolts are tightened. Securelyretighten after a few hours of operation, as bolts can loosen up on new machinery. Check wheel boltsupon delivery and periodically thereafter. Wheel bolts should be tightened at 100 ft/lbs. of torqueon MS1442H and 300 ft/lbs. of torque on MS1455H

2. Check the tires and inflate to the recommended pressure (385/65R-22.5 and 425/65R-22.5 tires to85 psi).

3. Adjust the tractor hitch and attach the spreader to the tractor as described in the following sections. 4. Attach hydraulic hoses to double acting valves on tractor. 5. Lubricate the machine completely and check the oil level of the gearbox. 6. Before operation, run machine slowly to make sure that the spreader is operating and lubricated properly.

ATTACHING TO THE TRACTOR1.

2.

3.

4.

5.

6.

OPERATION

TRACTOR HITCHThe hitch of the spreader is designed for astandardized tractor hitch. Adjust the drawbar sothat it is 13 to 17 inches above the ground. Extendor shorten it so that the horizontal distance from theend of the tractor power takeoff shaft to the centerof the hitch pin hole is 14 inches for 540 PTO and15-3/4” for 1000 PTO as shown in drawing. Animproperly located hitch point may cause damageto the universal joints of the power takeoff. Securethe drawbar so that the hitch pin hole is directlybelow the power drive line.

If this implement is attached to a tractor with a clevishitch (hammer-strap) style drawbar, the hammer-strapmust be removed to prevent damage to the IID guardingand the IID telescoping members.[See Figure 1]

If this implement is attached to a tractor with an offset inthe drawbar, be certain it is in the down position toprevent damage to the IID guarding and the IIDtelescoping members. [See Figure 2]

Fasten the spreader hitch to the drawbar with a hitch pin with a safety locking device. Use 2”diameter hitch pin to pull spreader.Remove the weight from the jack (jack is not to be used when spreader is loaded). Remove jack frompipe mount and place on convenient storage mount located on the side of the left push frame brace.This allows protection of jack from tractor tires during turns.ATTENTION: Remove tractor quick coupler (If equipped). Tractor three point hitch arm should beremoved or positioned so they cannot come in contact with spreader. Failure to heed will causedamage to spreader and Void Warranty.Connect hydraulic hoses which operate the spreader hydraulic push gate from the spreader to adouble acting valve on the tractor.Connect hydraulic hoses which operate the hydraulic endgate to another double acting valve on thetractor.Slide spring loaded locking collar on PTO yoke rearward, and slide it onto the tractor PTO shaft.Release spring loaded collar. Be sure the pins fall into the groove of the tractor PTO shaft and collarsnaps forward into locking position. CAUTION: Do not use a steel hammer to aid in joining PTO parts.

-13-

LOADINGIn freezing weather, make certain that hydraulic tailgate is not frozen to the sides or on the floor of thespreader. Make sure the push gate is not frozen to the spreader floor or any lumps of manure arefrozen to the floor.

Begin loading the spreader at the front end and work toward the rear until loading is completed. Loadingthis way permits the material to be spread uniformly. Loading front to rear is particularly important when thespreader is loaded by a mechanical loader because this type of load requires more power to spread thanother loads.

When hauling extremely heavy materials with a large portion of dirt, it may be necessary to reduce the loadsize to prevent excessive shear bolt breakage. Never dump material onto the beater. Do not use extrasideboards. Do not overload spreader. Overloading decreases spreading effectiveness. Do not load morethan 15 inches above the beater (Horizontal Beater).

SPREADING1. Engage tractor PTO slowly. Beater is always in the engaged position, therefore, engaging tractor

PTO will automatically start the beaters.2. Raise the hydraulic endgate by engaging the tractor hydraulics. Note: Hydraulic endgate MUST

BE RAISED COMPLETELY prior to engaging hydraulic pushgate.3. Engage tractor hydraulics to operate spreader push gate.4. Control the speed of the spreader push gate by rotating the lever on the flow control valve (A),

located on the PTO shield near the front of the spreader. If the tractor is equipped with in cab flowcontrol, the lever on the flow control valve can be put in the full flow position and the spreaderpush gate can be controlled with the in cab control.

5. When the spreader is empty disengage the tractor PTO (which will stop the beater). Engage tractorhydraulics to return the spreader pushgate. When spreader push gate is completely retractedengage tractor hydraulics to close hydraulic endgate.

-14-

When transporting on the highway, connect power cord from tractor to spreader. Make surelights functioning properly. Regularly clean the reflective tape and SMV sign at the rear of thespreader.

SERVICINGBe certain to disconnect all sources of power before servicing. Keep pant cuffs and loose clothing awayfrom all chains and drives as well as the other moving parts. Keep off the equipment when in use, and keepall shields in place. Do not attempt to clean, grease or lubricate while the machine is running.Never allow riders in or on the machine.

A

OPERATION (Continued)

ADJUSTMENTSFAILURE TO FOLLOW THE RECOMMENDED ADJUSTMENTS WILL VOID WARRANTY

-15-

PRIMARY & SECOND BEATER DRIVE CHAINSBoth beater drive chains can be adjusted by looseningbolts (A)and sliding poly tensioners toward the chain until1/2” of deflection can be obtained on the opposite side(B).Retighten bolts (A) when deflection is obtained.

NOTE: PERIODICALLY LUBRICATE ALL ROLLER CHAINS WITH A LIGHT MACHINE OIL.

Shields Removed for Clarity

B

A

B

BE SURE ALL SHIELDS ARE SECURED INTOPLACE PRIOR TO RE-STARTING MACHINE.

SHEAR BOLTBoth beaters at the rear of the spreader are protected by one shear bolt located in the PTO at the front ofthe spreader. Four spare shear bolts are provided. Shearing of bolts is normally due to large frozenchunks of manure, foreign objects (rocks, chunks of wood etc.) in the manure, running spreader push gatetoo fast when unloading long straw and pen-packed material, or STARTING SPREADER PTO TOOQUICKLY WITH HIGH TRACTOR RPM’S. Always determine the reason for shearing bolt and eliminate theproblem before replacing shear bolt. Always use proper Frontier shear bolt (540 RPM HP42N985/16”-18 x 2” GR. 8 bolt, HPD81 5/16”-18 lock nut) or (1000 RPM HP42N97 5/16”-18 x 2” GR. 5 bolt,HP1D81 5/16”-18 lock nut.

Shear Bolt

Spare Shear Bolts

ADJUSTING WHEEL HUBSTo adjust wheel hubs, tighten the castellated nut on the spindle to the point where there is no end-play anda slight drag on the bearings. Replace the cotter key with a new one of the correct size.

540 RPM = 5/16x2 GR 81000 RPM = 5/16x2 GR 5

BEATER REMOVALBEATER REMOVALThe beater attachment can easily beremoved for various reasons such asmanure stock piling. Remove bolts, nuts andlockwashers (A). Remove connector link onchain (B). Strip chain from sprockets. Set boltsand chain aside. Securely attach alifting chain to lifting eyes at the top of thebeater assembly (C) on vertical beater andto the upper beater (D) on the horizontalbeater. Using a proper lifting device, liftbeater assembly gently until alignment pegsare clear of the alignment holes (E).Horizontal Beater Assembly Weighs: 620 lbs.Vertical Beater Assembly Weighs: 1940 lbs.

BEATER STORAGEBefore the beater assembly isremoved, make sure the legs(Part # HPHGV10) are securely boltedin place (F). The beater assemblymust be stored on a flat levelconcrete surface.

Shields Removed for Clairty

B

A

C

E

CLEAN OUT PANThe clean out pan should be used at the end of each day or between each load during freezing weather.To trip the pan pull forward on lever (G). The pan (H) will drop and allow manure build up to fall to theground. Note: The endgate should be completely raised and the push gate fully extended (All the wayto the rear of the spreader). To reset the clean out pan lift up on handle (I).

-16-

D

E

A

A

F

BEATER TIMINGBeaters must be timed so flighting ofopposite beater is half way betweenthe beater being timed. To time beaters,remove top shield and remove one chaincoupler between the two gear cases sobeater can be turned for proper timing isachieved. Reconnect chain coupler andreinstall shield.

G

H

I

-17-

LUBRICATION GUIDEThe operator should become familiar with all lubrication points and establish a systematic routine to ensurecomplete and quick lubrication of the machine.

GREASE FITTINGSThere are numerous grease fittings on the spreader. If these are lubricated properly and often enough, it willprolong the life of the spreader. (Grease every 20 hours, also before and after power washing.) Makecertain that the grease fittings are free of paint and dirt, force a high-quality grease into them until the greasecomes out around the shaft on the sleeve-type bearings. On the sealed ball bearings, grease should beadded slowly until a slight bead forms at the seals indicating the correct amount of lubricant.Wipe off excess grease to prevent the accumulation of chaff and grit around the bearings.

A F B H E G H D

C (Behind Shield) H G E H D D Shields Removed for Clarity

Shields Removed for Clarity

GREASE ZERK LOCATIONA. (3) PTO Shaft F. (2) Over Running Clutch (Rear Half of PTO)B. (2) Front Drive Shaft Bearings. G. (2) Each Axle Pivot (Remote Zerk)C. (1) Gear Box Output Shaft H. (4) Each Wheel HubD. (4) Each Beater End I. (2) Each Lower Beater BearingE. (2) Endgate Pivot Points J. (1) Gearbox Drive Shaft

LUBRICATION GUIDE (CONTINUED)

GEARBOXBefore using your new machine, check the oil in thebeater drive gearbox or gearboxes (Vertical Beaters).Keep the gearbox filled to the oil plug on the side of thegearbox as shown with Mobilube SHC 75W90 (orequivilant) gear lube.

-18-

CHECK PLUG

I Shields Removed for Clairty

J

K

CHAIN OILERThe Vertical Beater attachment is equipped with a chainoiler. The oiler will place a prescribed amount of oil tothe drive chains every time the hydraulic endgate israised. Warm weather the oiler should be filled with a#30 oil and cold weather #10 oil. The reservoir (K) islocated behind the shield at the right rear of thespreader. Maintain oil level no less than 1/4 tank.

(Gearbox is located underneath rear of spreader)

LUBRICATION GUIDE (CONTINUED)

-19-

PTO ASSEMBLY- Care must be taken to keep the male and female drivingelements well lubricated and free sliding. Failure to observe this precautionwill result in excessive pressure being required to collapse or extend theassembly while subject to operating torque. This excessive force may damageor displace the main shaft bearings. DO NOT lubricate the shield surfaces.The shield surfaces must be kept dry, as dirt accumulation on them willquickly cause these units to bind and not rotate. Care should also be taken tobe certain that the rotating integral shields are not dented or damaged, asthis also will result in excessive force being applied against the jackshaft.Damaged shields also cause obvious difficulties when installing the assembly.If at any time the shields do not turn freely, they should be checked todetermine the cause, and repaired or cleaned. To avoid damage to the maindrive bearings, avoid turning sharp corners while PTO is running. Start andStop PTO slowly to avoid damage to the drive line.

When replacing beater paddles (Horizontal Beaters), the sharp edges of the teeth must lead in thedirection of beater travel. On the right half of the beater the teeth must point to the right side of thespreader. On the left half of the beater the teeth must point to the left side of the spreader. Always useFrontier special grade 5 bolts, washers, and nuts when replacing tips. Use Frontier part numberHPR10 (1/2” special bolt), HPR35 (1/2” lock washer), HPR11 (1/2” special nut), torque to 60 foot lbs.

BEATER

When transporting on the highway, connect power cord from tractor to spreader. Make surellights function properly. Regularly clean the reflective tape and SMV sign at the rear of thespreader.

DRIVE CHAINSThe drive chains are lubricated by a automatic chain oiler. This will extend the life of the drive chains. Keepchains aligned with sprockets, this will also lengthen the life of the sprockets and drive chains.

DECAL LOCATIONYour Frontier Manure Spreader was manufactured with operator safety in mind. Located on the manurespreader are various decals to aid in operation, and warn of danger or caution areas. Pay close attentionto all decals on your Manure Spreader.

DO NOT REMOVE ANY OF THESE DECALS. IF DECALS ARE LOST, DAMAGED, OR IFMANURE SPREADER IS REPAINTED, REPLACE DECALS. REMEMBER: DECALSARE FOR YOUR PROTECTION AND INFORMATION.

Listed below are the decals on your Manure Spreader. These decals may be ordered individually by partnumber or by ordering a complete set.

ITEM PART NO. DESCRIPTIONA HP1442H (2) Frontier MS1442H Decals

HP1455H (2) Frontier MS1455H DecalsB HP2X9AMBER (6) Amber ReflectorC HP1494K (1) Warning - Do Not Remove ShieldsD HPFRON1 Warning - Help Avoid InjuryE HP9194B Danger - Never Allow RidersF HP1494L Danger - Rotating DrivelineG HP9194A (5) Danger - No Step (7) Vertical BeatersH Serial NumberI HP1494B Warning - Do Not Remove ShieldsJ HP1494J (3) Warning - Do Not Clean or WorkK HPFRONTIER19 (3) Frontier DecalL HP71188B Jack Storage PositionM HP111593C (2) Warning - Stay Clear of EndgateN HP111593A (2) Danger - Stay Clear of BeaterO HP2X9RED (2) Red ReflectorsP HP11599 (3) Warning - Stay Clear of LeaksQ HP82602 (2) Warning - Crushing HazardR 5HPHS404 Patent NumberS. HP32597A Warning - Do Not OperateT. HP1906C (2) Warning - Stay ClearU. HP1906D (2) Danger - Stay ClearV. HP12306 Shear BoltW. HP1906E (2) Warning - Stay ClearX. HP1906F Danger - Keep Out (3) MS1442H (5) MS1455HY. HP123002 (2) Warning - Stay Clear of EndgateZ. HP93366 Keep Operators Manual HereAA. HP51606 Warning - Do Not OperateBB. HP71706 Attention - Tractor 3pt HitchCC. HP3494A (2) Remote Grease FittingDD. HP1494A (2) Warning - Do Not OperateEE. HP92606 Warning - Do Not Exceed Transport Speed

5HP720061442 Complete Set of Decals for MS1442H5HP720061455 Complete Set of Decals for MS1455H

-20-

BB

T

G

V

Q

AA H EE P G G L U R B K(Behind Shield)

E W K P X W J

DA

Y

X

CC (Behind Tire)

ITEM PART NO. DESCRIPTIONFF. HP93020 (2) Grease FittingGG. HP71494A (2) Warning - Do Not

Remove ShieldsHH. HP12794 (2) Warning - Do Not

Operate

DECAL LOCATION (CONTINUED)

-21-

Y M J N O DD Z DD S

O N J C I M Y FF FF

A B K E B W K P U G P G Q T

Shields Removed for ClarityHH (Behind Shield)

GGN

J

C

G

N

C

REAR PANThe rear pan shown below is optionalequipment on the MS1442H & MS1455Hspreader. The rear pan option allows for aeven spread when light applications areneeded.

OPTIONAL EQUIPMENT

TROUBLE SHOOTINGWARNINGMAKE SURE THAT THE TRACTOR IS SHUT OFF AND THE SPREADER CAN NOT MOVEBEFORE SERVICING THE MANURE SPREADER. MAINTENANCE AND REPAIR SERVICEWORK TO BE PERFORMED BY A QUALIFIED SERVICE PERSON ONLY.

TROUBLE... POSSIBLE CAUSE... POSSIBLE REMEDY...

-22-

Beater Will Not Run Tractor PTO Not Turning Engage Tractor PTO

PTO Shaft Shear Bolt Sheared Replace PTO Shaft Shear Bolt(See Page #15)

Primary Beater Drive Chain Off, Replace or Repair Primary BeaterBroken or Missing Drive Chain (See Page #15)

Key Sheared or Missing on Beater Replace Sheared or Missing KeyDrive or Driven Sprocket

Top Beater Does Not Turn Secondary Beater Drive Chain Replace or Repair Secondary BeaterOff, Broken or Missing Drive Chain (See Page #15)

Push Gate Will Not Move Tractor Hydraulics Not Engaged Engage Tractor Hydraulics

Flow Control Valve Turned Off Reset Flow Control Valve(See Page #14)

Low Tractor Hydraulic Flow or Have Servicing Dealer Check TractorPressure Flow And Pressure

Hydraulic Couplers Not Coupled Couple Hoses To TractorTo Tractor Properly (See Page #13)

Spreader Is Over Loaded Reduce Load

When transporting on the highway, connect power cord from tractor to spreader. Make surelights function properly. Regularly clean the reflective tape and SMV sign at the rear of thespreader.

-23-

INSTRUCTIONS FOR ORDERING PARTS

All service parts should be ordered through your authorized Frontier dealer. He will be able to giveyou faster service if you will provide them with the following:

1. Model & Serial Number - Both can be located on the side of the front center bearing post above the jack mount.

2. All references to left or right apply to the machine as viewed from the rear.

3. Parts should not be ordered from illustration only. Please order complete part number.

4. If your dealer has to order parts - give shipping instructions:

VIA truck - large pieces (please specify local truck lines)

VIA United Parcel Service (include full address)

PLEASE RECORD NUMBERS FOR YOUR UNIT FOR QUICK REFERENCE

ABOUT IMPROVEMENTS

FRONTIER IS CONTINUALLY STRIVING TO IMPROVE IT’S PRODUCTS

We must therefore, reserve the right to make improvements or changes whenever it becomes practical todo so, without incurring any obligation to make changes or additions to the equipment previously sold.

-24-

FIGURE 1

35

-25-

ITEM MS1442H MS1455H DESCRIPTION1. HP27N14 “ Jack2. HP12N13 “ Jack Pin & Chain3. HP12N12 “ Jack Handle4. HP16SV329 “ PTO Shield5. HP42N1 “ Shield Mount6. HPX97 “ Hair Pin7. HP16SV327 “ PTO Shield Bottom8. HP42N2 “ PTO Holder9. HP42N3 “ Spring10. HP12N14 “ Jack Mount11. HP42N4 “ Wood Rail12. HP42N5 HP55N1 Front Panel13. HP42N43 “ SMV Bracket * “ SMV Sign14. HP16SV89 - Wheel 13.5 x 22.5 (8 Bolt) * - HP60N15 Wheel 13.5 x 22.5 (10 Bolt) * HP42N138 - Tire (385 x 22.5 Truck) * - HP16SV88 Tire (425 x 22.5 Truck)15. HPBFR405 - 1/2” x 5-1/2” Bolt GR. 5 * - HP16SV77 1/2” x 6” Bolt GR. 516. HP45N35 HP16SV214 Collar For Axle17. HP9S17 “ 1/2” Lock Nut18. HP45N57 “ Grease Line Adapter19. HPS47 “ Grease Fitting20. HP42N41 “ Grease Line21. HP16V9 “ Grease Bracket22. HP45N36 HP16SV75 Bushing For Tandem Axle23. HP42N6 HP55N2 Tandem Axle Left24. HP42N7 HP55N3 Tandem Axle Right25. HP31N4 “ Roll Pin26. HP33SV40 HP66N15 Spindle27. HP33SV45 HP60N8 Hub28. HP33SV42 HP60N5 Seal29. HP33SV43 HP60N7 Inner Bearing30. HP33SV44 HP60N6 Inner Race31. HPRG169 HP60N10 Outer Race32. HPRG170 HP60N9 Outer Bearing33. HP33SV95 HP60N2 Washer34. HPRG17 HP60N3 Spindle Nut35. HP33SV46 HP60N4 Cotter Pin36. HPRG171 HP60N11 Hub Cap37. HP33SV41 HP60N13 Stud38. HPRG72 HP60N14 Lug Nut39. HP42N8 HP55N4 Side Poly Right * HP42N9 HP55N5 Side Poly Left40. HP42N10 “ Floor Poly Right * HP42N11 “ Floor Poly Left41. HP42N12 “ Poly Side Angle42. HPF97 “ SMV Holder43. HP42N97 “ 5/16” x 2” Shear Bolt GR.5 (1000 RPM) * HP42N98 - 5/16” x 2” Shear Bolt GR. 8 (540 RPM)44. HPD81 “ Lock NutNOTE: * (MEANS NOT SHOWN)

- (MEANS NOT USED ON THIS MODEL)“ (MEANS SAME AS PREVIOUS PART NO.)

FIGURE 1FRONTIER MODEL MS1442H & MS1455H

FRAME ASSEMBLY

FIGURE 2

-26-


BEATER DRIVE TRAIN

ITEM MS1442H MS1455H DESCRIPTION1. HP42N13 “ Input Shaft Shield2. HP42N14 “ Input Shield Angle3. HP42N15 “ Input Shield Back4. HPS138 “ 3/8” x 2-3/8” Key5. HP12V62 “ Snap Ring6. HP42N16 “ Input PVC Shield7. HP16SV379 “ 3/8” x 2-1/2” Roll Pin8. HP12V67 “ Bearing9. HP42N17 “ Input Shaft10. HP42N18 “ Bearing11. HP42N19 “ Drive Shaft Center PVC Shield12. HP42N137 “ Bearing Saddle13. HP42N20 “ Drive Shaft Middle PVC Shield14. HP42N21 “ Drive Shaft Back PVC Shield15. HP42N22 “ Cross Shaft16. HP42N23 “ Cross Shaft PVC Shield17. HP42N24 “ Sprocket 50-B-20 1-1/2” Bore18. HP42N25 “ Sprocket 50-B-20 1-3/4” Bore19. HPPB136 “ 3/8” x 2” Key20. HP42N26 “ Gearbox21. HPG83 “ Set Screw22. HP42N27 “ Connector Chain #50 x 20 Pitches23. HP12V104 “ 20 T Sprocket24. HP42N49 “ Gearbox Gusset25. HP42N99 “ 3/8” U-Bolt26. HP42N100 “ Bearing27. HP42N101 “ Hose Holder28. HP42N102 “ 5/16” x 2” ID U-BoltNOTE: “ (MEANS SAME AS PREVIOUS PART NO.)

- (MEANS NOT USED ON THIS MODEL)

-27-

FIGURE 3

-28-


ENDGATE & BEATERITEM MS1442H MS1455H DESCRIPTION1. HP42N28 HP55N9 Endgate2. HP42N29 HP55N10 Hinge Pin3. HP42N30 HP55N11 Endgate Poly Holdown4. HP42N31 HP55N12 Endgate Rubber Right5. HP42N32 HP55N13 Endgate Rubber Left6. HP42N33 HP55N14 Endgate Rubber7. HP42N34 HP55N15 Endgate Poly8. HP42N35 HP55N16 Beater Panel9. HP42N36 “ Blade Holder Right10. HP42N37 “ Blade Holder Left11. HP42N38 “ Beater12. HP56N69 “ Beater Stub Shaft13. HP42N39 “ Beater Drive Shaft14. HP42N40 “ Beater Slot Filler15. HP23N277 “ Beater Blade16. HPR11 “ 1/2” Lock Nut17. HPR35 “ Lock Washer18. HPR10 “ 1/2” x 1-1/4” Beater Blade Bolt GR. 519. HPS436 - 3/8” x 1-1/2” Key * - HPPB136 3/8” x 2” Key20. HP42N42 HP42N38 Second Beater21. HP45N27 HP23N277 Second Beater Blade22. HP45N43 - Blade Holder * - HP42N36 Blade Holder Right * - HP42N37 Blade Holder Left23. HPG83 “ 3/8” Set Screw24. HP42N44 - Second Beater Sprocket 60-B-30 * - HP16SV213 Second Beater Sprocket 80-B-2325. HP42N45 - Second Beater Chain #60 x 98 Pitches * - HP55N17 Second Beater Chain #80 x 82 Pitches26. HPF157 HPD39 Connector Link27. HP42N46 - Beater Sprocket #80, 20T To #60, 25T (540 RPM) * - HP55N19 Beater Sprocket #80, 36T To #80, 20T (1000 RPM) * HP42N47 - Beater Sprocket #80, 36T To #60, 25T (1000 RPM)28. HP16SV34 - Beater Chain #80 x 79 Pitches (540 RPM) * HP42N48 “ Beater Chain #80 x 88 Pitches (1000 RPM)29. - HP55N18 Second Beater Slot Filler30. HP16SV72 “ Pillow Block Bearing31. HP42N50 “ Poly Chain Tightener32. HP42N51 “ Tightener Stop33. HP42N52 HP55N20 Main Panel Right End34. HP42N53 - Second Beater Anti-Wrap35. HP42N54 HP55N21 Rear Shield36. HP42N55 HP55N22 Shield Filler37. HP42N56 “ Cross Shaft Shield38. HPF69 “ Shield Bracket39. HPF56 “ Clip Pin40. HP42N103 “ Beater Spacer41. HP42N104 - Second Beater Shield42. HPX193 “ Latch Catch Bracket43. HPX192 “ Latch (Rubber)44. HPX195 “ Pin45. HP42N105 “ Back Stake Filler46. HPX194 “ Latch Mounting Bracket47. HP42N141 “ 3/8” x 2-1/4” Key48. HPS414 “ Cap49. HPS415 “ Manual Holder Tube50. HPS416 “ Manual Holder Clamp51. HPS418 “ Cap w/Hole52. HP42N142 - Stub Shaft Shield53. HPF157 “ #80 Connector LinkNOTE: * (MEANS NOT SHOWN) - (MEANS NOT USED ON THIS MODEL) “ (MEANS SAME AS PREVIOUS PART NO.)

-29-

FIGURE 4

-30-

38

38


HYDRAULICSITEM MS1442H MS1455H DESCRIPTION1. HPDWM205 “ Quick Coupler Male2. HP12SV25 - Hydraulic Hose 3/8” x 145” (1/2”MPX x 3/8”MPX) * - HP55N82 Hydraulic Hose 3/8’’ x 155” (1/2”MP x 3/8”MP)3. HPBFR74 “ 3/8” Tee4. HP46N40 “ Hydraulic Hose 3/8” x 46” (3/8”MPX x 3/8”MP)5. HPBFR287 “ Hydraulic Hose 3/8” x 36” (3/8”MPX x 3/8”MP)6. HPHE59 “ 3/8” Elbow7. HP42N59 HP55N23 End Gate Hydraulic Line Short8. HP42N60 HP55N24 End Gate Hydraulic Line Long9. HP12V19 “ Hydraulic Hose 3/8” x 24” (3/8”FP x 3/8”MPX)10. HP45N45 “ Hydraulic Cylinder (2’’ x 20”)11. HP56N141 “ Cylinder Pin12. HP23N108 “ 7/32” x 2” Cotter Pin13. HP42N61 - Hydraulic Hose 3/8” x 93” (1/2”MP x 1/2”MP) * - HP55N6 Hydraulic Hose 1/2” x 93” (1/2”MP x 1/2”MP)14. HP42N62 - Hydraulic Hose 3/8” x 95” (3/8”MP x 1/2”MP) * - HP55N7 Hydraulic Hose 1/2” x 95” (1/2”MP x 1/2”MP)15. HPJB82 - 1/2” x 3/8” Bushing16. HP23N116 - 3/8’’ Service Tee * - HPLW96 1/2” Service Tee17. HP42N63 - Hydraulic Hose 3/8” x 82” (3/8”MPX x 3/8”MPX 90°) * - HP55N8 Hydraulic Hose 1/2” x 82” (1/2”MPX x 1/2”MPX 90°)18. HP23N234 - 3/8” Street Elbow * - HPHE58 1/2” Street Elbow19. HP16SV351 “ 3/8” Nipple Nut20. HP16SV339 “ Sequence Valve21. HPWM146 - 3/8” Male, Female Tee * - HPDF8 1/2” Tee22. HP42N64 “ Hose Shield (1-1/2”ID x 73”)23. HP42N65 - Hydraulic Hose 3/8” x 158” (3/8”MPX 90° x 3/8”MPX) * - HP55N29 Hydraulic Hose 1/2” x 158” (1/2”MPX 90° x 1/2”MPX)24. HP42N66 - Hydraulic Hose 3/8” x 76” (3/8”MP x 3/8”MP) * - HP55N30 Hydraulic Hose 1/2” x 76” (1/2”MP x 1/2”MP)25. HP42N67 - 3/8” Union Adapter 45° * - HP55N65 1/2” Union Adapter 45°26. HPDWM110 - 3/8” Union Adapter 90° * - HPHE58 1/2” Street Elbow27. HP42N68 - Hydraulic Hose 3/8” x 20-1/2” (3/8”MP x 3/8”MPX 90°) * - HP16SV143 Hydraulic Hose 1/2” x 19” (1/2”MP x 1/2”MPX)28. HP42N69 - Hydraulic Cylinder 3-1/2” x 90” Gimbal Mount * - HP55N32 Hydraulic Cylinder 4-1/2” x 90” Gimbal Mount29. HP42N70 - Hydraulic Cylinder 3-1/2” x 90” Trunnion Mount * - HP55N33 Hydraulic Cylinder 4-1/2” x 90” Trunnion Mount30. HP42N71 HP55N34 Cylinder Pin31. HP42N72 HP55N35 Pusher Cylinder Pin32. HP12V70 - Hose Clamp SAE#88 * - HP55N66 Hose Clamp SAE#10433. HP42N73 “ Flow Control34. - HPJB82 1/2” To 3/8” Bushing35. - HP16SV351 3/8” Nipple Nut36. HPDWM233 - 3/8” Union Adapter * - HP55N70 1/2” Union Adapter37. HP23N116 - 3/8” Service Tee * - HPWM139 1/2” Male-Female Tee38. HPT144 “ Cylinder Clip PinNOTE: * (MEANS NOT SHOWN) - (MEANS NOT USED ON THIS MODEL) “ (MEANS SAME AS PREVIOUS PART NO.)

-31-

FIGURE 5


HYDRAULIC END GATE CYLINDER

ITEM MS1442H MS1455H DESCRIPTION1. HP23N142A “ Clevis Cap2. HP23N143A “ Rod Cap3. HP23N144 “ Piston4. HP45N42 “ Rod5. HP45N43 “ Cylinder Tube6. HP45N44 “ Tie Rod7. HP23N148 “ Piston Nut8. HP23N149 “ Plug9. HP23N150A “ Rod Clevis10. HP23N151 “ Seal Kit11 HP45N45 “ Hydraulic CylinderNOTE: “ (MEANS SAME AS PREVIOUS PART NO.)

-32-

FIGURE 6


HYDRAULIC PUSHER CYLINDERITEM MS1442H MS1455H DESCRIPTION1. HP42N106 HP55N36 Internal Head2. HP42N107 HP55N37 Barrel Assembly (Top Cylinder) * HP42N108 HP55N38 Barrel Assembly (Bottom Cylinder)3. HP42N109 HP55N39 Piston4. HP42N110 HP55N40 Lock Nut5. HP42N111 HP55N41 Spacer6. HP42N112 HP55N42 Rod7. HP42N113 HP55N43 Seal Kit7A. “ “ Wear Ring7B. “ “ Poly Hone7C. “ “ O-Ring7D. “ “ O-Ring7E. “ “ O-Ring7F. “ “ Back-up Ring7G. “ “ Wear Ring7H. “ “ Loaded U-Cup7J. “ “ Rod Wiper * HP42N69 HP55N32 Complete Cylinder (Top) * HP42N70 HP55N33 Complete Cylinder (Bottom)NOTE: * (MEANS NOT SHOWN) “ (PART NOT SOLD SEPARATELY ONLY COMPLETE KIT)

-33-

FIGURE 7

-34-


PUSHER

ITEM MS1442H MS1455H DESCRIPTION1. HP42N74 HP55N44 Moveable Floor Tube2. HP42N75 HP55N45 Pusher Tubing Slide3. HP42N76 HP55N46 Pusher Tube Front Guide4. HP42N77 HP55N47 Cylinder Retainer5. HP42N78 HP55N48 End Cap Clamp Right6. HP42N79 HP55N49 End Cap Clamp Left7. HP3G21 - 1” Snap Ring * - HPF73 1-1/4” Snap Ring8. HP42N80 HP55N50 Rear Cylinder Pin9. HP42N81 HP55N81 Pusher Wiper10. HP42N82 HP55N25 Pusher Rubber Strap11. HP42N83 HP55N26 Pusher12. HP42N84 HP55N51 Cylinder Shield13. HP42N114 - Pusher Shim (As Required)14. HP50N183 “ 5/8” x 1-1/4” Bolt GR. 515. HP42N85 HP55N52 Poly Block Spacer16. HP42N86 HP55N53 Pusher Poly Slide17. HP42N87 HP55N54 Poly Block Spacer Right18. HP42N88 HP55N55 Pusher Poly Slide Right19. HP42N89 HP55N56 Pusher Poly Slide Left20. HP42N90 HP55N57 Poly Block Spacer Left21. HPA7 - 1/2” x 9-1/2” Bolt GR. 5 * - HP55N58 1/2” x 10-1/2” Bolt GR. 522. HP42N91 HP55N59 Pusher Spacer23. HP42N92 HP55N27 Pusher Rubber Left * HP42N93 HP55N28 Pusher Rubber Right24. HP42N94 “ Pusher Extension25. HP42N95 “ Extension Wing Right26. HP42N96 “ Extension Wing Left27. HP42N139 HP55N83 Pusher Bottom Rubber28. HP42N140 HP16SV379 3/8” Expansion PinNOTE: * (MEANS NOT SHOWN)

- (MEANS NOT USED ON THIS MODEL)

-35-

FIGURE 8

-36-

ITEM MS1442H MS1455H DESCRIPTION1. HPG125 “ Housing2. HPG138 “ Gasket3. HPG126 “ Cover4. HPG144 “ 3/8” Vent Plug5. HPG140 “ Cap6. HPG65 “ 3/8” Plug - NPT7. HPG56 “ 5/16” x 5/8” Cap Screw8. HPG145 “ 3/8” Plug9. HPG130 “ Snap Ring10. HPG128 “ Bearing Cup #2552011. HPG129 “ Bearing #2558112. HPG132 “ Stake Nut13. HPG142 “ Bevel Gear 22 Teeth14. HPG136 “ Seal - Output15. HP42N57 “ Output Shaft16. HPG61 “ “E” 1210 Woodruff Key17. HPG133 “ Stake Nut18. HPG137 “ Seal - Input19. HP42N58 “ Input Shaft20. HPG139 “ 3/8” x 1-1/2” Hardened Key21. HPG127 “ Bevel Gear 33 Teeth * HP42N26 “ Complete Gear BoxNOTE * (MEANS NOT SHOWN) - (MEANS SAME AS PREVIOUS PART NO.)


BEATER GEAR BOX

-37-

FIGURE 9

-38-

FIGURE 9FRONTIER MODEL MS1442H & MS1455HVERTICAL BEATERS FRAME ASSEMBLY

ITEM MS1442H MS1455H DESCRIPTION1. HPHGV54 HPHGV55 Frame2. HPHGV3 HPHGV4 Rear Shield3. HPHGV5 HPHGV6 Shield Filler4. HPHGV7 “ Cross Shaft Shield5. HPHGV8 “ Beater Bottom Mount6. HPHGV9 “ Pan Hinge7. HPHGV10 “ Leg8. HPHGV11 “ Pan Bottom9. HPHGV12 “ Pan10. HPK103 “ Spring11. HPHGV13 “ Pan Handle12. HPHGV14 “ Pan Handle Stop13. HPHGV56 “ Gearbox Bottom Shield14. HPHGV57 “ Gearbox Top Shield15. HPHGV17 “ Chain Damper16. HPS416 “ Manual Holder Clamp17. HPS414 “ Cap18. HPS415 “ Manual Holder Tube19. HPS418 “ Cap w/Hole20. HPHGV18 “ Sprocket Idler Shaft21. HP12V62 “ Snap Ring22. HPF69 “ Shield Bracket23. HPF56 “ Clip Pin24. HP42N105 “ Back Stake Filler25. HPX195 “ Pin26. HPX194 “ Latch Mounting Bracket27. HPX192 “ Latch (Rubber)28. HPX193 “ Latch Catch Bracket29. HPHGV48 “ 5/16” x 1-1/2” Step Bolt30. HPHGV49 “ Stone Guard31. HPHGV50 “ Lifting Eye32. HPHGV51 “ Grease Line33. HPHGV52 “ Grease Fitting34. HPHGV53 “ Chain Damper Top35. HP16SV64 “ 3/4” Flange Nut36. HP16SV44 “ Tightener Spacer37. HPHE8 “ 3/4” x 2-1/4” Bolt GR.538. - HPHGV103 Main Panel Brace Left39. - HPHGV104 Main Panel Brace Right40. HPHGV108 “ Latch Pivot Bolt (3/4” X 3-1/2” CarriageNOTE: “ (MEANS SAME AS PREVIOUS MODEL) Bolt Gr. 5)

* (MEANS NOT SHOWN)

-39-

FIGURE 10

-40-


VERTICAL BEATERS DRIVE TRAIN

ITEM MS1442H MS1455H DESCRIPTION1. HPHGV19 HPHGV20 Beater Left Hand2. HPHGV21 HPHGV22 Beater Right Hand * HPHGV102 “ Beater Stub Shaft3. HPHGV23 “ Beater Blade Left4. HPHGV24 “ Beater Blade Right5. HPHGV27 “ Seal6. HPB5 “ Bearing Cone7. HPB5A “ Bearing Cup8. HP3G18 “ Bearing Cup9. HP3G7 “ Bearing Cone10. HPBFR63 “ Washer11. HPBFR64 “ Nut12. HPBFR65 “ Cotter Pin13. HP17G144 “ Hub Cap14. HPS38 “ 3/8” x 2-3/8” Square Key15. HPHGV58 “ Gearbox Left16. HPHGV29 “ Gearbox Connector17. HP42N25 “ Sprocket 50-B-20 1-3/4” Bore18. HP42N27 “ Connector Chain #50 x 20 Pitches * HPD118 “ Connector Link #5019. HPHGV59 “ Gearbox Cross Shaft20. HPHGV60 “ Gearbox Right21. HPHGV61 “ Gearbox Drive Shaft22. HPHGV41 “ Bearing23. HPHGV25 “ Sprocket 80-B-20 1-3/4” Bore24. - HPHGV34 Gearbox Chain #80 x 136 Pitches * HPHGV35 - Gearbox Chain #80 x 97 Pitches * HPF157 “ Connector Link #8025. HP12V52 “ Bearing26. HP12V77 “ Idler Sprocket w/Bearing (80-A-12)27. HPBFR374 “ I-Bolt 3/8” x 3”28. HPHGV36 “ Beater Tightener29. HP42N100 “ Bearing30. - HPHGV37 Sprocket 80-A-36 to 80-A-20 * HPHGV38 - Sprocket 80-A-20 to 80-A-2031. - HPHGV39 Drive Chain #80 x 117 Pitches * HPHGV40 - Drive Chain #80 x 109 Pitches * HPF157 “ Connector Link #8032. HPHGV46 “ I-Bolt 5/16” x 1”33. HP10R14 “ Spring34. HPHGV30 “ Spacer35. HPHGV43 “ Spacer36. HPHGV42 “ Tightener37. HP56N160 “ Spring Holder38. HPST36 “ SpringNOTE: * (MEANS NOT SHOWN)

“ (MEANS SAME AS PREVIOUS MODEL) - (MEANS NOT USED ON THIS MODEL)

-41-


VERTICAL BEATERS LEFT HAND GEARBOX

ITEM HP425VB HP550VB DESCRIPTION1. HPHGV88 “ Bottom Housing2. HPHGV89 “ Top Housing3. HPHGV90 “ Output Shaft4. HPHGV105 “ Input Shaft5. HPHGV91 “ Bearing Cone6. HPHGV92 “ Bearing Cup7. HPHGV93 “ Output Shaft8. HP23N288 “ 3/8” Nipple9. HPHGV95 “ Plug (1/2-14 NPT)10. HPHGV96 “ Gearbox Bolt11. HP17G58 “ Vent12. HPJB82 “ Bushing (1/2”NPT To 3/8”NPT)13. HPHGV99 “ Cap14. HPHGV94 “ Bearing Cone15. HPHGV97 “ Bearing Cone16. HPHGV112 “ Bearing Cup17. HPHGV98 “ Retaining Ring * HPHGV58 “ Complete Gearbox LeftNOTE: *(MEANS NOT SHOWN)

“ (MEANS SAME AS PREVIOUS MODEL)

FIGURE 12

-42-


VERTICAL BEATERS RIGHT HAND GEARBOX

ITEM HP425VB HP550VB DESCRIPTION1. HPHGV88 “ Bottom Housing2. HPHGV89 “ Top Housing3. HPHGV90 “ Output Shaft4. HPHGV101 “ Input Shaft5. HPHGV91 “ Bearing Cone6. HPHGV92 “ Bearing Cup7. HPHGV93 “ Seal8. HP23N288 “ 3/8” Nipple9. HPHGV95 “ Plug (12 -14 NPT)10. HPHGV96 “ Gearbox Bolt11. HP17G58 “ Vent12. HPJB82 “ Bushing (1/2” NPT To 3/8”NPT)13. HPHGV94 “ Bearing Cone14. HPHGV97 “ Bearing Cone15. HPHGV112 “ Bearing Cup16. HPHGV98 “ Retaining Ring * HPHGV60 Complete Gearbox Right

FIGURE 13

NOTE: * (MEANS NOT SHOWN) “ (MEANS SAME AS PREVIOUS MODEL)

-43-

FIGURE 14


PTO & OVERRUNNING CLUTCH

ITEM 540 RPM 1000 RPM 1-3/8” 1000 RPM 1-3/4” DESCRIPTION1. HP16SV274 “ HP16SV275 Auto-Lock Repair Kit2. HP42N115 HP55N68 HP55N69 Auto-Lock Yoke Assembly3. HP16SV179 “ “ 35R Cross Bearing Kit4. HP42N116 “ “ Yoke Shaft5. HP16SV181 “ “ Nylon Repair Kit6. HP16SV283 “ “ Safety Sign7. HP42N117 “ “ Outer Guard8. HP42N118 “ “ Inner Guard9. HP16SV286 “ “ Safety Sign10. HP42N119 “ “ Yoke, Tube & Slip Sleeve11. HP42N120 “ “ OR Ball Shear Assembly12. HP16SV193 “ “ 5/16”-18 Lock Nut13. HP42N98 - - 5/16”-18 x 2” Bolt GR. 8 (540 RPM) * - HP42N97 “ 5/16”-18 x 2” Bolt GR. 5 (1000 RPM) * HP42N122 HP55N72 HP55N73 Joint & Shaft Half Assembly w/Guard * HP42N123 HP55N74 HP55N75 Joint & Shaft Half Assembly * HP42N124 HP55N76 “ Joint & Tube Half Assembly w/Guard * HP42N125 HP55N77 “ Joint & Tube Half Assembly * HP42N126 HP55N78 HP55N79 Complete PTO * HPS204 “ “ PTO Safety ManualNOTE: * (MEANS NOT SHOWN)

- (MEANS NOT USED ON THIS MODEL)“ (MEANS SAME AS PREVIOUS PART NO.)

-44-

FIGURE 15


LIGHTING

ITEM MS1442H MS1455H DESCRIPTION1. HPS310 “ Red Tail Light2. HPS309 “ Yellow Hazard Light3. HPS308 “ Rubber Light Mount4. HP56N155 “ Tail Light Harness5. HPS441 “ Light Module6. HP56N154 “ Flasher Module Harness7. HPFBO-TLPC “ Tractor Cord8. HP55N60 “ Light Bracket Mount Left9. HP55N61 “ Light Bracket Left10. HP55N62 “ Light Bracket Right11. HP55N63 “ Light Plug Bracket12. HP55N64 “ Metal Cushioned Cable Clamps13. HPBFR666 “ Extension Light Harness14. HP55N80 “ Light Bracket Mount RightNOTE: “ (MEANS SAME AS PREVIOUS PART NO.)

-45-

-46-

FIGURE 16


CHAIN OILER

ITEM PART# DESCRIPTION1. HPHGV63 Reservoir2. HPHGV64 Hydraulic Hose 1/4” x 80”3. HPHGV65 O-Ring/JIC Elbow4. HPHGV66 Filler Hose5. HPHGV67 Brush6. HPHGV68 Pump Mount Bracket7. HPHGV69 Brush Bracket8. HPHGV70 Bracket Mount9. HPHGV71 Oiler Tube 5/32” (50’)10. HPHGV72 Small Tube Holder11. HPHGV73 3/16” x 3/8” Tap Tight12. HPHGV74 2” Hose Clamp13. HPHGV75 1” Hose Clamp * HPHGV76 Medium Tube HolderNOTE: * (MEANS NOT SHOWN)

ITEM PART# DESCRIPTION14. HPHGV77 Edging 12” * HPHGV78 Large Tube Holder15. HPHGV79 9/16” x 2-1/2” Bolt GR. 516. HPHGV80 9/16” Lockwasher17. HPHGV81 9/16” Nut18. HPST33 Angle19. HPBFR120 3/8” Union Adapter20. HPWM146 Male-Female Pipe Tee21. HPHGV82 Complete Pump * HPHGV83 Pump Repair Kit22. HPHGV84 Manifold Assembly (Complete)23. HPHGV85 Sleeve Nut24. HPHGV86 Standoff25. HPHGV87 Ferrule * HPHGV62 Complete Oiler Kit

FIGURE 17


OPTIONAL REAR PAN

ITEM MS1442H MS1455H DESCRIPTION1. HP42N127 “ Pan2. HPR70 “ 3/16” x 2” Cotter Pin3. HP42N128 “ Pan Plate Left4. HP42N129 “ Pan Plate Right5. HP42N130 “ Pan Strap6. HP42N131 “ Rubber7. HPHE7 “ 3/4” Lock Nut8. HPF69 “ Bracket9. HPST36 “ Spring10. HPT73 “ Washer11. HP42N132 “ Latch Bushing12. HP42N133 “ Latch13. HP42N134 “ Latch Spacer14. HP42N135 “ 3/4” x 2-1/2” Carriage Bolt GR. 515. HP23N212 “ 3/8” Long Nut16. HP23N213 “ 3/8” x 1” I-Bolt17. HP42N136 “ Rope (18’)18. HPBFR295 “ Snap Hook19. HP56N170 “ Pan WasherNOTE: “ (MEANS SAME AS PREVIOUS PART NO.)

-47-

SERVICE / MAINTENANCE RECORD

DATE DESCRIPTION NOTES

-48-

Date post:	20-Mar-2020
Category:	Documents
Upload:	others
View:	5 times
Download:	0 times

MS1442H & MS1455H Spreader OM Manual - John...

Documents