ATTACHCABLETO TOWVEHICLEPIN IN
SWITCH BOXFOR TOWING AND STORAGE
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCH BOX
NATM HITCH / COUPLER WARNINGCOMBINATION DECALS
1
KG01
ENOUGHSLACK
FOR TURNS
ATTACH TO TOWVEHICLE STRUCTURE
© 2002 NATM
PIN PULLED OUT, ONLY TO TEST BRAKES
PINSWITCH BOX
ATTACHCABLETO TOWVEHICLE
PIN INSWITCH BOX FORTOWING ANDSTORAGE
DISCONNECTED CONNECTED
PART # KG01 5.5” X 2.75” ORANGE AND BLACK
Sleeve back
Sleeveforward
Lift Coupler to check
Pin in place
Coupler open
ENOUGHSLACK
FOR TURNS
ATTACH TO TOW VEHICLE FRAME
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box:
PULL hard to get pin out of switch box.
pin will be pulled out if trailer separates.
1.2. CHECK brake by PULLING TRAILER
with tow vehicle.3. ATTACH pin CABLE to tow vehicle so
4. Promptly REPLACE pin in switch box.
DISCONNECTED CONNECTED
KG02
PART # KG02 7.25” X 2.75” ORANGE AND BLACK
KG03
Open clamp
Closed clamp
Pin in place
Pin removed
ATTACH TO TOW VEHICLE FRAME
ENOUGHSLACKFOR TURNS
CROSS CHAINS ATTACH CABLETO TOW VEHICLE
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCHBOX PIN IN
SWITCH BOXFOR TOWINGANDSTORAGE
DISCONNECTED CONNECTED
PART # KG03 7.25” X 2.75” ORANGE AND BLACK
GOOSENECK / ELECTRIC BRAKE
BULLDOG / ELECTRIC BRAKE
PINTLE HOOK / ELECTRIC BRAKE
NATM HITCH / COUPLER WARNINGCOMBINATION DECALS
ENOUGH SLACKFOR TURNS
ATTACH HOOKS TO TOW VEHICLE FRAME
CROSS CHAINS
Openclamp
Lift coupler to check
Closed clamp
Pin or padlockin place
CheckFluidLevel
AttachTo TowVehicle
Break-awayBrake Chain
Trailer can roll if it comes loose. Safetybrake applies when chain pulls brake lever.
1. ATTACH brake CHAIN securely to tow vehicle so lever will be pulled if trailer separates. 2. CHECK brake fluid level. 3. DO NOT TOW trailer if brake fluid is NOT FULL.
DISCONNECTED CONNECTED
KG04
PART # KG04 7.25” X 2.75” ORANGE AND BLACK
KG05
ENOUGH SLACKFOR TURNS
ATTACH HOOKS TO TOW VEHICLE FRAME
CROSS CHAINS
Openclamp
Lift coupler to check
Closed clamp
Pin or padlockin place
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCH BOX
ATTACHCABLE
TO TOWVEHICLE SWITCH BOX FOR
TOWING ANDSTORAGE
PIN IN
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box.
Lights can prevent trailer from beinghit by other vehicles. You must:
1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
DISCONNECTED CONNECTED
pin will be pulled out if trailer separates.
1. PULL hard to get pin out of switch box.2. CHECK brake by PULLING TRAILER
with tow vehicle.3. ATTACH pin CABLE to tow vehicle so
4. Promptly REPLACE pin in switch box.
PART # KG05 7.25” X 2.75” ORANGE AND BLACK
Kenny & Gyl Company is a member of NATM and alicensed manufacturer of copyrighted safety decals for theNational Association of Trailer Manufacturers.Use our expertise with the support of NATM tohelp limit your product liability.
2
BUMPER PULL / SURGE BRAKE
BUMPER PULL / ELECTRIC BRAKE
NATM HITCH/COUPLER WARNINGWITH LUG NUT SAFETY
3
Tires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
KG06
ENOUGHSLACK
FOR TURNS
ATTACH TO TOWVEHICLE STRUCTURE
PIN PULLED OUT, ONLY TO TEST BRAKES
PINSWITCH BOX
ATTACHCABLETO TOWVEHICLE
PIN INSWITCH BOX FORTOWING ANDSTORAGE
DISCONNECTED CONNECTED
PART # KG06 7.25” X 2.75” ORANGE AND BLACK
Lights can prevent trailer from beinghit by other vehicles. You must:
1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
DISCONNECTED CONNECTED
Tires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
KG07
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box:
PULL hard to get pin out of switch box.
pin will be pulled out if trailer separates.
1.2. CHECK brake by PULLING TRAILER
with tow vehicle.3. ATTACH pin CABLE to tow vehicle so
4. Promptly REPLACE pin in switch box.
ATTACHCABLETO TOWVEHICLEPIN IN
SWITCH BOXFOR TOWING AND STORAGE
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCH BOX
ENOUGHSLACK
FOR TURNS
ATTACH TO TOW VEHICLE FRAMESleeve back
Sleeveforward
Lift Coupler to check
Pin in place
Coupler open
PART # KG07 9” X 2.75” ORANGE AND BLACK
PART # KG08 9” X 2.75” ORANGE AND BLACK
Lights can prevent trailer from beinghit by other vehicles. You must:
1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
Tires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
Open clamp
Closed clamp
Pin in place
Pin removed
ATTACH CABLETO TOW VEHICLE
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCHBOX PIN IN
SWITCH BOXFOR TOWINGANDSTORAGE
ATTACH TO TOW VEHICLE FRAME
ENOUGHSLACKFOR TURNS
CROSS CHAINS
KG08
DISCONNECTED CONNECTED
GOOSENECK / ELECTRIC BRAKE
BULLDOG / ELECTRIC BRAKE
PINTLE HOOK / ELECTRIC BRAKE
NATM HITCH/COUPLER WARNINGWITH LUG NUT SAFETY
KG09
Lights can prevent trailer from beinghit by other vehicles. You must:
1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
DISCONNECTED CONNECTED
Tires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
WARNING WARNING WARNING WARNING WARNING
ENOUGH SLACKFOR TURNS
ATTACH HOOKS TO TOW VEHICLE FRAME
CROSS CHAINS
Openclamp
Lift coupler to check
Closed clamp
Pin or padlockin place
CheckFluidLevel
AttachTo TowVehicle
Break-awayBrake Chain
Lights can prevent trailer from beinghit by other vehicles. You must:
1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
DISCONNECTED CONNECTED
Tires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
ENOUGH SLACKFOR TURNS
ATTACH HOOKS TO TOW VEHICLE FRAME
CROSS CHAINS
Openclamp
Lift coupler to check
Closed clamp
Pin or padlockin place
CheckFluidLevel
AttachTo TowVehicle
Break-awayBrake Chain
Lights can prevent trailer from beinghit by other vehicles. You must:
1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
DISCONNECTED CONNECTED
Tires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
ENOUGH SLACKFOR TURNS
ATTACH HOOKS TO TOW VEHICLE FRAME
CROSS CHAINS
Openclamp
Lift coupler to check
Closed clamp
Pin or padlockin place
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCH BOX
ATTACHCABLE
TO TOWVEHICLE SWITCH BOX FOR
TOWING ANDSTORAGE
PIN IN
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box.
pin will be pulled out if trailer separates.
1. PULL hard to get pin out of switch box.2. CHECK brake by PULLING TRAILER
with tow vehicle.3. ATTACH pin CABLE to tow vehicle so
4. Promptly REPLACE pin in switch box.
KG10
4
PART # KG09 9” X 2.75” ORANGE AND BLACK
PART # KG10 9” X 2.75” ORANGE AND BLACK
BUMPER PULL / SURGE BRAKE
BUMPER PULL / ELECTRIC BRAKE
PART # KG104 12.15” X 3” ORANGE AND BLACK
PART # KG105 16.25” X 3” ORANGE AND BLACK
PART # KG106 9.25” X 5.25” ORANGE AND BLACK
5
WARNINGTrailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box:
1. PULL hard to get pin out of switch box.2. CHECK brake by PULLING TRAILER
with tow vehicle.3. ATTACH pin CABLE to tow vehicle so
pin will be pulled out if trailer separates.4. Promptly REPLACE pin in switch box.
© 2002 NATM
ATTACHCABLETO TOWVEHICLEPIN IN
SWITCH BOXFOR TOWING ANDSTORAGE T0037
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCH BOX
WARNING
T0036© 2002 NATM
ALWAYS use safety chains.Chains hold trailer if connection fails.You must: 1. CROSS chains underneath coupler. 2. ALLOW slack for trailer to turn. 3. ATTACH chain hooks securely to tow vehicle frame.
ENOUGHSLACK
FOR TURNS
ATTACH TO TOW VEHICLE FRAME
WARNINGLights can prevent trailer from beinghit by other vehicles. You must: 1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
T0027© 2002 NATM
DISCONNECTED CONNECTED WARNINGImproper loading can cause trailer swayand sudden loss of control. You must: • Make certain weight of load plus trailer weight does not exceed trailer’s capacity (GVWR- Gross Vehicle Weight Rating). • Load heavier items in front of wheels. • Load evenly side to side. • SECURE load to trailer.
T0017© 2002 NATM
Balance loadside to side
Less loadin rear
More load infront of wheels
Secure loadto trailer
WARNING
T0030
Sleeve back
Sleeveforward
Lift Coupler to check© 2002 NATM
Pin in place
Coupler open
Uncoupling will cause trailer to comeloose from tow vehicle. You must: 1. CHECK that ball LOAD RATING is same or greater than coupler LOAD RATING. 2. CHECK that ball SIZE is same as coupler. 3. CLOSE COUPLER CLAMP on ball. 4. LIFT coupler upwards to test that it will not separate from ball. 5. LOCK sleeve with pin or padlock.
WARNING
T0019© 2002 NATMTires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
WARNING
T0019© 2002 NATMTires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
WARNING
T0034© 2002 NATM
ATTACH TO TOW VEHICLE FRAME
ALWAYS use safety chains.Chains hold trailer if connection fails.You must: 1. CROSS chains underneath coupler. 2. ALLOW slack for trailer to turn. 3. ATTACH chain hooks securely to tow vehicle frame.
ENOUGHSLACKFOR TURNS
CROSS CHAINS
WARNING
ATTACH CABLETO TOW VEHICLE
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCHBOX PIN IN
SWITCH BOXFOR TOWINGANDSTORAGE
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box: 1. PULL hard to get pin out of switch box. 2. CHECK brake by PULLING TRAILER with tow vehicle. 3. ATTACH pin CABLE to tow vehicle so pin will be pulled out if trailer separates. 4. Promptly REPLACE pin in switch box.
T0035© 2002 NATM
WARNINGLights can prevent trailer from beinghit by other vehicles. You must: 1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
T0027© 2002 NATM
DISCONNECTED CONNECTEDWARNINGImproper loading can cause trailer swayand sudden loss of control. You must: • Make certain weight of load plus trailer weight does not exceed trailer’s capacity (GVWR- Gross Vehicle Weight Rating). • Load heavier items in front of wheels. • Load evenly side to side. • SECURE load to trailer.
T0017© 2002 NATM
Balance loadside to side
Less loadin rear
More load infront of wheels
Secure loadto trailer
WARNINGUncoupling will cause trailer to comeloose from tow vehicle.
1. CHECK that pintle LOAD RATING is same or greater than ring LOAD RATING. 2. LOCK the clamp in place using a pin or lock.
T0029
Open clamp
Closed clamp© 2002 NATM
Pin in place
Pin removed
WARNING CHECKBEFORE TOWING!
WARNING
© 2002 NATM T0024
Improper loading can cause trailer swayand sudden loss of control. You must: • Make certain weight of load plus trailer weight does not exceed trailer’s capacity (GVWR- Gross Vehicle Weight Rating). • Load heavier items in front of wheels. • Load evenly side to side. • SECURE load to trailer. • Close and PIN or LOCK doors.
Balance loadside to side
Less loadin rear
More load infront of wheels
WARNINGTrailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box: 1. PULL hard to get pin out of switch box. 2. CHECK brake by PULLING TRAILER with tow vehicle. 3. ATTACH pin CABLE to tow vehicle so pin will be pulled out if trailer separates. 4. Promptly REPLACE pin in switch box.© 2002 NATM
PIN PULLED OUT, ONLY TO TEST BRAKES
T0015
PINSWITCH BOX
ATTACHCABLETO TOWVEHICLE
PIN INSWITCH BOX FORTOWING ANDSTORAGE
WARNINGLights can prevent trailer from beinghit by other vehicles. You must: 1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
T0027© 2002 NATM
DISCONNECTED CONNECTED
WARNING
T0021© 2002 NATM
ENOUGHSLACK
FOR TURNS
ATTACH TO TOWVEHICLE STRUCTURE WARNING
T0019© 2002 NATMTires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
WARNINGUncoupling will cause trailer to comeloose from tow vehicle. You must:
1. CHECK that ball LOAD RATING is same as or greater than coupler LOAD RATING. 2. CHECK that ball SIZE is same as coupler. 3. CLOSE COUPLER CLAMP on ball. 4. LIFT coupler upwards to test that it will not separate from ball. 5. LOCK coupler clamp with pin or padlock.
NATM SAFETY COMBINATION DECALS(ONE PART COVERS ALL SAFETY APPLICATIONS)
BULLDOG HITCH / COMBINATION
PINTLE HOOK / COMBINATION
GOOSENECK / COMBINATION
NATM SAFETY COMBINATION DECALS(ONE PART COVERS ALL SAFETY APPLICATIONS)
PART # KG107 13.875” X 3.5” ORANGE AND BLACK
PART # KG108 9.25” X 3.5” ORANGE AND BLACK
6
Improper loading can cause trailer swayand sudden loss of control. You must: • Make certain weight of load plus trailer weight does not exceed trailer’s capacity (GVWR- Gross Vehicle Weight Rating). • Load heavier items in front of wheels. • Load evenly side to side. • SECURE load to trailer.
T0017© 2002 NATM
Balance loadside to side
Less loadin rear
More load infront of wheels
Secure loadto trailerWARNING
WARNING
T0020
ENOUGH SLACKFOR TURNS
ATTACH HOOKS TO TOW VEHICLE FRAME
CROSS CHAINS
WARNINGUncoupling will cause trailer to comeloose from tow vehicle. You must:
1. CHECK that ball LOAD RATING is same as or greater than coupler LOAD RATING. 2. CHECK that ball SIZE is same as coupler. 3. CLOSE COUPLER CLAMP on ball. 4. LIFT coupler upwards to test that it will not separate from ball. 5. LOCK coupler clamp with pin or padlock.
T0016
Openclamp
Lift coupler to check
Closed clamp
Pin or padlockin place
©2002 NATM
WARNINGLights can prevent trailer from beinghit by other vehicles. You must: 1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
T0026© 2002 NATM
DISCONNECTED CONNECTED
WARNING
T0019© 2002 NATMTires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
pin will be pulled out if trailer separates.
T0014
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCH BOX
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box.
1. PULL hard to get pin out of switch box.2. CHECK brake by PULLING TRAILER
with tow vehicle.3. ATTACH pin CABLE to tow vehicle so
4. Promptly REPLACE pin in switch box.
ATTACHCABLE
TO TOWVEHICLE SWITCH BOX FOR
TOWING ANDSTORAGE
PIN IN
© 2002 NATM
WARNING
Uncoupling will cause trailer to comeloose from tow vehicle.
1. CHECK that pintle LOAD RATING is same or greater than ring LOAD RATING. 2. LOCK the clamp in place using a pin or lock.
T0029
Open clamp
Closed clamp© 2002 NATM
Pin in place
Pin removed
WARNING
WARNING
T0034© 2002 NATM
ATTACH TO TOW VEHICLE FRAME
ALWAYS use safety chains.Chains hold trailer if connection fails.You must: 1. CROSS chains underneath coupler. 2. ALLOW slack for trailer to turn. 3. ATTACH chain hooks securely to tow vehicle frame.
ENOUGHSLACKFOR TURNS
CROSS CHAINS
WARNING
T0019© 2002 NATMTires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
WARNING
ATTACH CABLETO TOW VEHICLE
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCHBOX PIN IN
SWITCH BOXFOR TOWINGANDSTORAGE
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box: 1. PULL hard to get pin out of switch box. 2. CHECK brake by PULLING TRAILER with tow vehicle. 3. ATTACH pin CABLE to tow vehicle so pin will be pulled out if trailer separates. 4. Promptly REPLACE pin in switch box.
T0035© 2002 NATM
Combinations shown are standard items. You may create yourown combination by selecting specific individual labels frompages 7 and 8 and combining them into the set sizes shown tomeet your specific equipment requirements.
There is NO CHARGE for group changes to meet yourspecific requirements.
BUMPER PULL / COMBINATION
PINTLE HOOK / COMBINATION
NATM SAFETY WARNING DECALS
7
PART # T00146” X 2.25”ORANGE / BLACK
pin will be pulled out if trailer separates.
T0014
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCH BOX
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box.
1. PULL hard to get pin out of switch box.2. CHECK brake by PULLING TRAILER
with tow vehicle.3. ATTACH pin CABLE to tow vehicle so
4. Promptly REPLACE pin in switch box.
ATTACHCABLE
TO TOWVEHICLE SWITCH BOX FOR
TOWING ANDSTORAGE
PIN IN
© 2002 NATM
WARNING WARNINGTrailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box: 1. PULL hard to get pin out of switch box. 2. CHECK brake by PULLING TRAILER with tow vehicle. 3. ATTACH pin CABLE to tow vehicle so pin will be pulled out if trailer separates. 4. Promptly REPLACE pin in switch box.© 2002 NATM
PIN PULLED OUT, ONLY TO TEST BRAKES
T0015
PINSWITCH BOX
ATTACHCABLETO TOWVEHICLE
PIN INSWITCH BOX FORTOWING ANDSTORAGE
WARNINGImproper loading can cause trailer swayand sudden loss of control. You must: • Make certain weight of load plus trailer weight does not exceed trailer’s capacity (GVWR- Gross Vehicle Weight Rating). • Load heavier items in front of wheels. • Load evenly side to side. • SECURE load to trailer.
T0017© 2002 NATM
Balance loadside to side
Less loadin rear
More load infront of wheels
Secure loadto trailer
PART # T00156” X 2.25”ORANGE / BLACK
PART # T00166” X 2.25”ORANGE / BLACK
PART # T00176” X 2.25”ORANGE / BLACK
WARNINGUncoupling will cause trailer to comeloose from tow vehicle. You must:
1. CHECK that ball LOAD RATING is same as or greater than coupler LOAD RATING. 2. CHECK that ball SIZE is same as coupler. 3. CLOSE COUPLER CLAMP on ball. 4. LIFT coupler upwards to test that it will not separate from ball. 5. LOCK coupler clamp with pin or padlock.
T0016
Openclamp
Lift coupler to check
Closed clamp
Pin or padlockin place
©2002 NATM
PART # T00196” X 2.25”ORANGE / BLACK
PART # T00206” X 2.25”ORANGE / BLACK
PART # T00246” X 2.25”ORANGE / BLACK
WARNING
T0019© 2002 NATMTires and Wheels OK?
Lug NutsTIGHT?
Tire, wheel or lugnut failure can cause loss ofcontrol. Before towing, you must CHECK: 1. Tire pressure and tread. 2. Tires and wheels for damage. 3. Lug nuts for tightness.
For new and remounted wheels, re-tighten lug nuts at the first 10, 25 and 50 miles of driving.
WARNING
T0020
ENOUGH SLACKFOR TURNS
ATTACH HOOKS TO TOW VEHICLE FRAME
CROSS CHAINS
WARNING
© 2002 NATM T0024
Improper loading can cause trailer swayand sudden loss of control. You must: • Make certain weight of load plus trailer weight does not exceed trailer’s capacity (GVWR- Gross Vehicle Weight Rating). • Load heavier items in front of wheels. • Load evenly side to side. • SECURE load to trailer. • Close and PIN or LOCK doors.
Balance loadside to side
Less loadin rear
More load infront of wheels
WARNING
T0021© 2002 NATM
ENOUGHSLACK
FOR TURNS
ATTACH TO TOWVEHICLE STRUCTURE
PART # T00216” X 2.25”ORANGE / BLACK
NATM SAFETY WARNING DECALS
8
PART # T00276” X 2.25”ORANGE / BLACK
PART # T00286” X 2.25”ORANGE / BLACK
PART # T00296” X 2.25”ORANGE / BLACK
WARNINGLights can prevent trailer from beinghit by other vehicles. You must: 1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
T0027© 2002 NATM
DISCONNECTED CONNECTED
WARNING CheckFluidLevel
AttachTo TowVehicle
Break-awayBrake Chain
Trailer can roll if it comes loose. Safetybrake applies when chain pulls brake lever. 1. ATTACH brake CHAIN securely to tow vehicle so lever will be pulled if trailer separates. 2. CHECK brake fluid level. 3. DO NOT TOW trailer if brake fluid is NOT FULL.© 2002 NATM T0028
WARNINGUncoupling will cause trailer to comeloose from tow vehicle.
1. CHECK that pintle LOAD RATING is same or greater than ring LOAD RATING. 2. LOCK the clamp in place using a pin or lock.
T0029
Open clamp
Closed clamp© 2002 NATM
Pin in place
Pin removed
WARNINGLights can prevent trailer from beinghit by other vehicles. You must: 1. CONNECT trailer and tow vehicle electrical connectors. 2. CHECK all lights: tail lights, turn signal, and brake lights. 3. DO NOT TOW if lights are not working.
T0026© 2002 NATM
DISCONNECTED CONNECTED
PART # T00266” X 2.25”ORANGE / BLACK
PART # T00346” X 2.25”ORANGE / BLACK
PART # T00356” X 2.25”ORANGE / BLACK
PART # T00366” X 2.25”ORANGE / BLACK
WARNING
T0034© 2002 NATM
ATTACH TO TOW VEHICLE FRAME
ALWAYS use safety chains.Chains hold trailer if connection fails.You must: 1. CROSS chains underneath coupler. 2. ALLOW slack for trailer to turn. 3. ATTACH chain hooks securely to tow vehicle frame.
ENOUGHSLACKFOR TURNS
CROSS CHAINS
WARNING
ATTACH CABLETO TOW VEHICLE
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCHBOX PIN IN
SWITCH BOXFOR TOWINGANDSTORAGE
Trailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box: 1. PULL hard to get pin out of switch box. 2. CHECK brake by PULLING TRAILER with tow vehicle. 3. ATTACH pin CABLE to tow vehicle so pin will be pulled out if trailer separates. 4. Promptly REPLACE pin in switch box.
T0035© 2002 NATM
WARNING
T0036© 2002 NATM
ALWAYS use safety chains.Chains hold trailer if connection fails.You must: 1. CROSS chains underneath coupler. 2. ALLOW slack for trailer to turn. 3. ATTACH chain hooks securely to tow vehicle frame.
ENOUGHSLACK
FOR TURNS
ATTACH TO TOW VEHICLE FRAME
PART # T00306” X 2.25”ORANGE / BLACK
WARNING
T0030
Sleeve back
Sleeveforward
Lift Coupler to check© 2002 NATM
Pin in place
Coupler open
Uncoupling will cause trailer to comeloose from tow vehicle. You must: 1. CHECK that ball LOAD RATING is same or greater than coupler LOAD RATING. 2. CHECK that ball SIZE is same as coupler. 3. CLOSE COUPLER CLAMP on ball. 4. LIFT coupler upwards to test that it will not separate from ball. 5. LOCK sleeve with pin or padlock.
PART # T00376” X 2.25”ORANGE / BLACK
WARNINGTrailer can roll if it comes loose.Electric safety brake applies whencable pulls pin out of switch box:
1. PULL hard to get pin out of switch box.2. CHECK brake by PULLING TRAILER
with tow vehicle.3. ATTACH pin CABLE to tow vehicle so
pin will be pulled out if trailer separates.4. Promptly REPLACE pin in switch box.
© 2002 NATM
ATTACHCABLETO TOWVEHICLEPIN IN
SWITCH BOXFOR TOWING ANDSTORAGE T0037
PIN
PIN PULLED OUT, ONLY TO TEST BRAKES
SWITCH BOX
9
TRI-SAFETY COMBINATION DECALS
PART # KG109 8” X 4” RED AND BLACK
DUMP TRAILER DANGER
PART # KG110 5.75” X 2.75” ORANGE AND BLACK
CHECK LIST WARNING
AVOID SERIOUS INJURY OR DEATH
Do not place body partsbetween trailer body andframe without service polein upright position.
DANGER
KENNY & GYL STOCK SAFETY DECALSANSI FORMATTED
PART # KG103 10.625” X 2” RED YELLOW ORANGE AND BLACK
WARNINGCAUTIONSERIOUS INJURY AND/ORPROPERTY DAMAGE CANRESULT IF THIS VEHICLE
IS TOWED BEFOREFAMILIARIZING YOURSELF
WITH THE MANUFACTURER’SOPERATING INSTRUCTIONS
AND CAUTIONS LISTEDTO THE RIGHT.
DANGER
WARNINGCheck following points each time before towing trailer.
DANGER CAUTION WARNING
KG11
PART # KG11 8.5” X 2” RED YELLOW ORANGE AND BLACK
BALL WARNING DECALS
PART # KG1002.25” X 2.25”ORANGE AND BLACK
PART # KG1012.25” X 2.25”ORANGE AND BLACK
PART # KG1022.25” X 2.25”ORANGE AND BLACK
10
WEIGHT CAUTION
PART # KG112 4.877” X 2.85” YELLOW AND BLACK
CAUTION
SECURE DOOR/GATE CAUTION
NO STEP
PART # KG1132.25” X 2.00”YELLOW AND BLACK
PART # KG114 4” X 1.125” BLACK
DO NOT EXCEEDMANUFACTURER’S VEHICLE
WEIGHT RATINGS OR LOADINGRECOMMENDATIONS -- GROSSVEHICLE, GROSS AXLE, GROSSCOMBINED VEHICLE AND AXLE.
CAUTION
11
LOAD/UNLOAD WARNING
PART # KG1154.625” X 2.00” ORANGE AND BLACK
PART # KG1163.875” X 1.875” RED AND BLACK
WARNING
DANGER
HEAVY DOOR DANGER
CAUTION
PINCH POINT CAUTION
PART # KG1173.875” X 1.875” YELLOW AND BLACK
12
LATCH GATES/SECURE LOAD CAUTION
PART # KG1184.88” X 2.85”YELLOW AND BLACK
CAUTIONPART# KG1194.88” X 2.85”YELLOW AND BLACK
LOW CLEARANCE WARNING
PART # KG1204.88” X 2.85”ORANGE AND BLACK
WARNING
13
WHEEL LUGS & TIRE PRESSURE CAUTION
14
Laser imprintable for all optional specifications.(Instructions and computer template provided)
Pre-printed.All specifications pre-printed and ready to apply.
(custom for your trailer style)
PART # KG-123.12” X 1.55”RED, YELLOWAND BLACK
PRINTED ON 8.5” X 11’ SHEETS OF 10
PART # KG-133.5” X 1.75”RED, YELLOWAND BLACK
KG122 CLEAR OVERLAY AVAILABLE
PART # KG1112" X 2.25"RED AND BLUE
15
OVERLOAD HAZARD
+
=
PART # KG123 4.0" X 1.875" ORANGE AND BLACK
PART # KG124 6.25" X 1.875" ORANGE AND BLACK
OVERLOAD HAZARD WARNING
OVERLOAD HAZARD WARNING
MADE IN USA DECAL
PART # KG128 3" X 3.5"RED AND BLUE
PART # KG127 3.9" X 3.03" ORANGE AND BLACK
16
PART # KG125 1" X 3" YELLOW AND BLACK
PART # KG126 4.12" X 2.9" RED AND BLACK
CAUTION: SLIPPERY WHEN WET
CARBON MONOXIDE DANGER
WHEEL SEPARATION WARNING
We DESIGN and MANUFACTURE:
•LOGOS
•CUSTOM SAFETY DECALS
•PRESPACED VINYL LETTERING
•INFORMATION DECALS
•INJECTION MOLDEDNAMEPLATES
CONTACT SALES AT Kenny & Gyl Company515-225-7007515-225-3042 [email protected]
Terms of sale: Net 30 days, FOB Des Moines, Iowa. Prices subject to change without notice or obligation.
As a NATM Member all of the design serviceis supplied to your company AT NO CHARGE!