+ All Categories
Home > Documents > OFC aman riz

OFC aman riz

Date post: 24-Oct-2014
Category:
Upload: kumar-rajiv
View: 79 times
Download: 0 times
Share this document with a friend
Popular Tags:
43
Optical Fiber Communication Systems Losses And Sensor Applications Module Code: CE00786-M CONTENTS: 1. INTRODUCTION……………………………………………………….………....4 1.1 CONNECTOR LOSSES…………………………………………….………….4 1.1.1 INTRINSIC LOSSES…………………………………………..............5 1.1.2 METHODS TO MINIMIZE INTRINSIC LOSSES……………………5 1.2 EXTRINSIC LOSSES………………………………………………………….5 1.3 METHODS TO MINIMIZE EXTRINSIC LOSSES…………………………..6 2. BENDING LOSS…………………………………………………………………..6 2.1 METHODS TO MINIMIZE BENDING LOSS………………………………..8 3. OPTICAL LOSS……………………………………………………………………8 3.1 METHODS TO MINIMIZE OPTICAL LOSS…………………………………9 4. MATERIALISTIC ABSORPTION LOSSES IN SILICA GLASS FIBERS………9 4.1 INTRINSIC ABSORPTION……………………………………………………9 4.1.1 METHODS TO MINIMIZE INTRINSIC LOSS……………………...10 4.2 EXTRINSIC ABSORPTION………………………………………………….10 4.2.1 METHODS TO MINIMIZE EXTRINSIC LOSS……………………..11 5. LOSS IN FIBER OPTIC DUE TO HYDROGEN ABSORPTION……………….11 5.1 METHODS TO MINIMZE LOSS IN FIBER OPTIC DUE TO HYDROGEN ABSORPTION………………………………………………………………...12 OPTICAL FIBER COMMUNICATION SYSTEMS Page 1
Transcript
Page 1: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

CONTENTS:

1. INTRODUCTION……………………………………………………….………....4

1.1 CONNECTOR LOSSES…………………………………………….………….4

1.1.1 INTRINSIC LOSSES…………………………………………..............5

1.1.2 METHODS TO MINIMIZE INTRINSIC LOSSES……………………5

1.2 EXTRINSIC LOSSES………………………………………………………….5

1.3 METHODS TO MINIMIZE EXTRINSIC LOSSES…………………………..6

2. BENDING LOSS…………………………………………………………………..6

2.1 METHODS TO MINIMIZE BENDING LOSS………………………………..8

3. OPTICAL LOSS……………………………………………………………………8

3.1 METHODS TO MINIMIZE OPTICAL LOSS…………………………………9

4. MATERIALISTIC ABSORPTION LOSSES IN SILICA GLASS FIBERS………9

4.1 INTRINSIC ABSORPTION……………………………………………………9

4.1.1 METHODS TO MINIMIZE INTRINSIC LOSS……………………...10

4.2 EXTRINSIC ABSORPTION………………………………………………….10

4.2.1 METHODS TO MINIMIZE EXTRINSIC LOSS……………………..11

5. LOSS IN FIBER OPTIC DUE TO HYDROGEN ABSORPTION……………….11

5.1 METHODS TO MINIMZE LOSS IN FIBER OPTIC DUE TO HYDROGEN

ABSORPTION………………………………………………………………...12

6. LOSS IN FIBER OPTIC DUE TO NUCLEAR RADIATION EXPOSURE……..12

6.1 MEHTODS TO MINIMIZE LOSS IN FIBER OPTIC DUE TO NUCLEAR

RADIATION EXPOSURE…………………………………………………....13

7. JOINT LOSS AND FIBER ALIGNMENT LOSS……………………………...…13

7.1 METHODS TO MINIMIZE JOINT LOSS AND FIBER ALIGNMENT LOSS

8. CONCLUSION …………………………………………………………………...15

9. INTRODUCTION…………………………………………………………………15

9.1 MICROBEND FIBER OPTIC SENSORS…………………………………….15

10. BASIC FIBER OPTIC SENSOR SYSTEM………………………………………19

10.1 INTENSITY TYPE FIBER OPTIC SENSOR MICROBENDING………19

10.2 INTENSITY TYPE FIBER OPTIC SENSOR USING EVANESCENT

WAVE COUPLING…………………………………………………………...19

11. MEASURING TEMPERATURE SENSORS IN PROCESS CONTROL……….20

11.1 SEMICONDUCTOR ABSORPTION SENSORS………………………...20

OPTICAL FIBER COMMUNICATION SYSTEMSPage 1

Page 2: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

12. BRAGG GRATING SENSOR FOR STRAIN MEASUREMENT……………….21

13. MEASUREMENT OF PIEZORESISTIVE PRESSURE SENSOR………………22

14. PERFORMANCE OF FIBER OPTICS BASED SENSORS IN COMPARISION

WITH TRADITIONAL SENSORS……………………………………………….23

15. CONCLUSION……………………………………………………………………24

16. TRANSMITTER AND RECEIVER PERFORMANCE CHARACTERISTICS OF

LED AND LASER………………………………………………………………..24

16.1.1 TRANSMITTER PERFORMANCE CHARACTERSITICS OF LED

AND LASER………………………………………………….............24

16.1.2 RECEIVER PERFORMANCE CHARACTERSITICS OF LED AND

LASER………………………………………………………………...27

16.2 COMPARISION OF LED SYSTEM AND LASER SYSTEM………………….30

17. REFERENCES………………………………………………………………………...31

LIST OF FIGURES PAGE NO

Fig 1.1.1 Intrinsic losses…………………………………………………………….............5

Fig 3.1 Optical loss in fiber…………………………………………………………………9

Fig 9.1 (a) Microbend fiber optic system………………………………………….............16

Fig 10.1 Fiber optic sensor system using microbending…………………………………..19

Fig 10.2 Fiber optic sensor system using evanescent wave coupling……………………..20

Fig 11.1 Temperature-dependent on GaAs light absorption…………………………........14

Fig 13.1 Piezoresistive pressure sensor chip………………………………………………22

LIST OF GRAPHS PAGE NO

Fig 1.2.1 Lateral Displacement……………………………………………………………..6

Fig1.2.2 Longitudinal Displacement………………………………………………………..6

Fig 2.1 Fiber attenuation due to microbending and macrobending…………………………7

Fig 2.2 Losses v/s mode-field diameter…………………………………………………….7

OPTICAL FIBER COMMUNICATION SYSTEMSPage 2

Page 3: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 4.1 Intrinsic material absorption loss………………………………………………….10

Fig 4.2 Extrinsic material absorption loss…………………………………………………11

Fig 5 Loss v/s wavelength in treated and untreated loss…………………….…………….12

Fig 6 Nuclear Radiation Exposure losses………………………………………………….13

Fig 7.1 Insertion loss due to lateral and longitudinal misalignments………………...........14

Fig 7.2 Insertion loss due to angular misalignment………………………………………..14

Fig 9.1 (b) Parabolic-profile fiber…………………………………………………………17

Fig 9.1 (c) Step-profile fiber………………………………………………………………18

Fig 12. Transmission spectrum of grating v/s wavelength……………………………… 21

Fig 13.2 Voltage v/s Pressure……………………………………………………………...23

APPENDICES : LIST OF TABLES:

Table 1- Operating Condition for LED Transmitter……………………………………....25

Table 2- Operating Condition for LASER Transmitter……………………………………25

Table 3- Electrical Characteristics of LED Transmitter…………………………………...25

Table 4- Electrical Characteristics of LASER Transmitter………………………………..26

Table 5- Optical Characteristics of LASER Transmitter………………………………….26

Table 6- Operating Conditions of LED Receiver …………………………………………27

Table 7- Operating Conditions of LASER Receiver………………………………………27

Table 8- Electrical Characteristics of LED Receiver……………………………………...28

Table 9- Electrical Characteristics of LASER Receiver…………………………………..28

Table 10- Optical Characteristics of LED Receiver……………………………………….28

Table 11- Optical Characteristics of LASER Receiver……………………………………29

OPTICAL FIBER COMMUNICATION SYSTEMSPage 3

Page 4: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

FIBER OPTIC LOSSES

1. INTRODUCTION

There are various numbers of reasons for the losses in optical fibers. These losses may

occur due to different types of material components being used in transmitting signals

over the transmission path. It can be categorized into numerous areas like Connector

losses which consists of intrinsic and extrinsic, Bending losses which consists of micro

bending and macro bending and Optical loss in which power plays major role. Hence

all kinds of losses are explained in detail below.

1.1 CONNECTOR LOSS:

This is one of the types of fiber optic losses; there are different factors which

results in attenuation of any two given fibers connected together. Connector losses

are divided into two, mainly intrinsic losses which are caused by the fiber. And the

next extrinsic losses caused by the connectors. Splices and Connectors when

inserted in given line direction are termed as insertion loss. Here we need to

considered short length of the fiber because if higher mode is taken then there is

higher numerical aperture and large size of the spot which causes higher losses at

times. So length plays am important factor in case of connector losses.

1.1.1 INTRINSIC LOSSES:

In general losses occurs because none of the fibers are same, there may be a

mismatch of numerical aperture, core area and core. When numerical aperture of

first fiber is larger than that of second it results in waste of light. And when light

travels in different direction, loss does not occur but gain is wrongly indicated.

For NA1>NA2, light transmitted in decibels.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 4

Page 5: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 1.1.1 Intrinsic losses.

(Source: James N. Downing, 2005)

In the opposite direction losses do not occur but the final intrinsic loss can be in

three cases. Firstly if in over lapped cores the geometry result, mismatch of

cladding diameter result and the ellipticity of the cores.

1.1.2 METHODS TO MINIMIZE INTRINSIC LOSSES:

The use of core and the cladding is the most better matched results to

minimize and in fact eliminate the intrinsic losses.

1.2 EXTRINSIC LOSSES:

In this case it all depends on the connectors used, since if any misalignment occurs

while connecting the connectors there occur some changes in fiber cores. The

displacement is of two types i.e. lateral and longitudinal displacement.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 5

Page 6: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

In case of the lateral displacement as shown in fig 1-2 for different displacements

ratios the graph shown is used in finding the loss. A loss of 2 db occurs for 30%

displacement. Where as in case of longitudinal displacement, if the angle is not

aligned correctly in results in producing more number of losses which in term gives

more emphasis on polishing of fiber and cleaving by using end cleaving procedure.

Fig 1.2.1 Lateral Displacement Fig1.2.2 Longitudinal Displacement

(Source: James N. Downing, 2005) (Source: James N. Downing, 2005)

1.3 METHODS TO MINIMIZE EXTRINSIC LOSSES:

There are different kinds of techniques used to eliminate the losses, whereas here in

this case the glass refining technique is used to reduce to acceptable levels.

2. BENDING LOSS:

There are two types of bending losses namely, microbending loss and

macrobending loss. These two losses are expressed in single mode fibers at 1550

nm region, the wavelength of lower cut off gets affected more precisely than other.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 6

Page 7: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 2.1 Fiber attenuation due to microbending and macrobending

(Source: V.S. Bagad, 2008)

To get low bending loss the diameter of mode field should be small, hence mode

field plays an important role in case of bending loss. The radius which is measured

inside the object is the minimum radius an object can be bend is termed as bend

radius, so if the bending radius is smaller then losses are higher and when the radius

is higher the losses are smaller. Hence bend radius is also vital in case of bending

loss.

Fig 2.2 Losses v/s mode-field diameter.

(Source: V.S. Bagad, 2008)

OPTICAL FIBER COMMUNICATION SYSTEMSPage 7

Page 8: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

2.1 METHODS TO MINIMIZE BENDING LOSSES:

1. The manufacturing of cable must be done to reduce the strain in case of

microbending loss.

2. In microbending attenuation is reduced by controlling coating of the fiber.

3. The fiber should be free from external pressure in microbending loss.

4. In case of macrobending, designing plays an important role i.e the

refractive index differences should be long.

5. And the wavelength should be as small as possible in order to reduce losses

in macrobending.

3. OPTICAL LOSS:

When a signal is transmitted along a path it mainly deals with the power, the

wavelength varies with the power. If signal power is reduced when travelling on the

path then it is termed as loss in signal. For a fiber with specific wavelength, the

ratio of output power to the input power is defined as optical loss.

Loss ratio= Tr = Pout/Pin

Loss ratio: Loss of power at a particular wavelength

Tr= Transmittance

Pout= average of output power of fiber

Pin = average of input power of fiber

In any passive path the output power of the optical fiber is always less than or equal

to the input power of the optical fiber. The fig 3.1 below shows the optical loss in

the fiber input as Input power (Pin) and output as output power (Pout).

OPTICAL FIBER COMMUNICATION SYSTEMSPage 8

Page 9: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 3.1 Optical loss in fiber.

(Source: Bob Chomycz, 2009)

3.1 METHODS TO MINIMIZE OPTICAL LOSS:

There are different reasons for the loss in optical fiber hence various methods

should be taken care of like the connectors when connected at the transmitter end

and at receiver end it should be properly connected .

4. MATERIALISTIC ABSORPTION LOSSES IN SILICA GLASS FIBERS:

In optical fibers there are number of reasons for the attenuation of the signal. The

absorption of the material is a mechanism of loss which is linked with the

combination of the process of fabrication in optical fiber and composition of the

material. So when optical power is transmitted heat is dissipated in the form of

waveguide. Hence the absorption is either in intrinsic or extrinsic.

4.1 INTRINSIC ABSORPTION:

A glass of Silica which is pure has very less intrinsic absorption. There are not

only one absorption in this but there are two intrinsic absorption.The graph

deals with the losses and Ultraviolet absorption and Infrared absorption with the

photon energy. The attenuation of the intrinsic loss mechanisms is pure in

GeO2-SiO2. It shows that absorption is more in Ultraviolet region than in

infrared region.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 9

Page 10: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 4.1 Intrinsic material absorption loss

(Source: John M. Senior, 1992)

4.1.1 METHODS TO MINIMIZE INTRINSIC ABSORPTION LOSS:

The use of core and the cladding is the most better matched results to

minimize and in fact eliminate the intrinsic losses.

4.2 EXTRINSIC ABSORPTION:

From the impurities of transition metal element a large amount of signal

attenuation is linked with the extrinsic absorption. The absorption losses are

mainly due to peak wavelength and different metallic ion impurities in glasses.

The impurities like chromium and copper can cause attenuation excess of 1 dB

km-1. Hence other absorption loss is due to water which is dissolved in glass.

The figure below shows the absorption spectrum for the hydroxyl.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 10

Page 11: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 4.2 Extrinsic material absorption loss

(Source: John M. Senior, 1992)

4.2.1 METHODS TO MINIMZE EXTRINSIC ABSORPTION LOSS:

There are different kinds of techniques used to eliminate the losses, whereas here in

this case the glass refining technique is used to reduce to acceptable levels.

5. LOSS IN FIBER OPTIC DUE TO HYDROGEN ABSORPTION:

The characteristic of spectral attenuation is affected due to the diffusion of the

hydrogen in optical fiber. New absorption peaks are formed by altering the spectral

loss, which causes in increase of hydrogen absorption in optical fiber.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 11

Page 12: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 5 Loss v/s wavelength in treated and untreated loss.

(Source: John M. Senior, 1992)

5.1 METHODS TO MINIMZE HYDROGEN ABSORPTION LOSS:

1. Cable should be given special care since if dipped or inserted in water it may cause

losses and selection of cable plays an important factor since each cable has its own

specification.

2. Hence the cable needs to be pressurized to prevent water from entering into it.

3. The fiber cable can be cleansed using inert gas.

6. LOSS IN FIBER OPTIC DUE TO NUCLEAR RADIATION EXPOSURE:

The characteristics while transmission of optical fiber cables have been reduced in

quality because of nuclear radiation. At the center of the fiber core the radiation

OPTICAL FIBER COMMUNICATION SYSTEMSPage 12

Page 13: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

makes colour and it results in spectral attenuation. The graph below shows the

effects of nuclear radiations with two optical fibers.

Fig 6 Nuclear Radiation Exposure losses

(Source: John M. Senior, 1992)

6.1 METHODS TO MINIMIZE NUCLEAR RADIATION LOSS:

1. With the help of photo bleaching the radiation which is induced can be

attenuated.

2. Using fibers which are resistant of radiation like silica cladding fiber

reduces gamma ray radiation.

7. JOINT LOSS AND FIBER ALIGNMENT LOSS:

When joining the optical fibers there may be misalignments being occurred which

results in different typer of alignments leading to losses. There are losses due to

lateral and longitudinal misalignments and losses due to angular misalignments.

Following are the graphs shown for the misalignments occurred.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 13

Page 14: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 7.1 Insertion loss due to lateral and longitudinal misalignments

(Source: John M. Senior, 1992)

Fig 7.2 Insertion loss due to angular misalignment.

(Source: John M. Senior, 1992)

OPTICAL FIBER COMMUNICATION SYSTEMSPage 14

Page 15: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

7.3 METHODS TO MINIMIZE FIBER ALIGNMENT LOSS:

The misalignment due to lateral is reduced by keeping the lateral offset value lateral below

5% of the core diameter of the fiber which results in reducing the insertion loss at a joint

below 0.5dB.

8. CONCLUSION:

From all the above losses explained we can understand the main reason behind the

losses which are occurring in fiber optics, there are few advantages and

disadvantages in fiber optic but if these losses are overcome then it will be a good

source for transmitting and receiving data and to be termed as the best means of

communication.

FIBER OPTIC BASED SENSORS:

9. INTRODUCTION:

The signals are transmitted in the form of light in the optical fiber as well as in it can be

very useful as sensors to measure different quantities. In case of industrial sectors sensors

play vital role since it will be helpful to keep an eye on such huge environment and if any

other method is used then it is quite expensive and difficult task. Therefore the sensors are

used to measure for different quantities using fiber optics technology. All the principles of

operation of the fibre optics based sensors used to measure such quantities.

9.1 MICROBEND FIBER OPTIC SENSORS:

This is one of the initial fiber optic sensor of all the sensors being used in fiber

optics. The losses occurring in microbend fiber optic resulted in designing the new

measurement technique for different variables such as temperature and pressure.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 15

Page 16: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

This sensor has many characteristics which resulted in using them in many

applications. In this case the range and sensitivity are increased for the variable

which can produce better results if increased where as sensitivity is decreased for

variables which are not needed.

Fig 9.1 (a) Microbend fiber optic system

(Source: K.T.V. Grattan and B.T. Meggitt, 1999)

There are two pressure plates in which there is an input given as laser light in the

fiber and is kept between the two plates to the detector. Since the light is not

allowed to come out in the open area the microbender is termed as intrinsic fiber

optic sensor.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 16

Page 17: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

A(mm)

Fig 9.1 (b) Parabolic-profile fiber

(Source: K.T.V. Grattan and B.T. Meggitt, 1999)

OPTICAL FIBER COMMUNICATION SYSTEMSPage 17

Page 18: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 9.1 (c) Step-profile fiber

(Source: K.T.V. Grattan and B.T. Meggitt, 1999)

In the complete given length to get the best out of the fiber the performance of the

binder was studied. The jacket connected to the fiber namely Teflon jacket and

rubber jacket contained sensitivity in microbend same when compared to fiber

without the jacket.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 18

Page 19: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

10. BASIC FIBER OPTIC SENSOR SYSTEM:

Depending on the particular functions of light each sensor is characterized by its

parameter. Frequency, phase and amplitude are some of the parameters. There are

different number of intensity based fiber optic sensors.

10.1 INTENSITY TYPE FIBER OPTIC SENSOR USING

MICROBENDING:

Due to bending of the fiber losses occur known as microbending losses. So the

light which is going to come at the receiving end depends on the amount of losses

occurred when the light was transmitted. Hence the microbending is measured to

use the fiber optic sensor

Fig 10.1 Fiber optic sensor using microbending.

(Source: Francis T.S. Yu and Shizhuo Yin, 2002)

10.2 INTENSITY TYPE FIBER OPTIC SENSOR USING EVANESCENT

WAVE COUPLING:

When light travels in a single mode fiber optic it not only go through the core but

also enters into the cladding region, so the wave of light in the region of cladding

is termed as evanescent wave. If two fibers are close to each other then the chances

of coupling is more. Another light travels in second fiber and a new evanescent

OPTICAL FIBER COMMUNICATION SYSTEMSPage 19

Page 20: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

wave is created such that both are quite close to each other which results in

coupling of both the waves. Hence it is known as evanescent wave coupling.

Fig 10.2 Fiber optic sensor using evanescent wave coupling.

(Source: Francis T.S. Yu and Shizhuo Yin, 2002)

11. MEASURING TEMPERATURE SENSORS IN PROCESS CONTROL:

Sensors play an important role in many electrical and chemical industries, here

temperature sensors is the most useful of all sensors. There are two types of

temperature sensors used namely low temperature sensor and high temperature

sensor. The range of low temperature sensor is -100 to +4000 C and if high

temperature sensor it is 500 to 20000 C.

11.1 SEMICONDUCTOR ABSORPTION SENSORS:

The graph below shows the curve with intensity and wavelength of GaAs

absorption curve. It is also one type of temperature sensor, the wavelength of the

signal light of the absorption edge shift is higher than the wavelength of reference

light.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 20

Page 21: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 11.1 Temperature-dependent on GaAs light absorption.

(Source: Sabrie Soloman, 1999)

12. BRAGG GRATING SENSOR FOR STRAIN MEASUREMENT:

Compared to other sensors where different types of techniques are used, in this case

of Bragg grating sensor the fabrication technique is used which is quite expensive

and complex of all. The gratings needs to be fabricated at an order of 10-3. The

graph shown below transmission spectrum of grating which is long period and there

occurs spiky losses and discrete band signals.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 21

Page 22: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 12. Transmission spectrum of grating v/s wavelength.

(Source: Michael Bass and Eric W. Van Stryland, 2002)

13. MEASUREMENT OF PIEZORESISTIVE PRESSURE SENSOR:

It consists of a silicon chip which results in forming of silicon at the bottom of the

diaphragm. Maximum strain occurs at the corners when there is a deflection caused

by difference in the pressures. Since the external circuit is electronic the pressure

can be sensed with the change in resistivity.

Fig 13.1 Piezoresistive pressure sensor chip

(Source: Sabrie Soloman, 1999)

Hence the graph below shows output voltage with respect to the pressure times full

scale range with different over range factors. There are three different pressure

range being taken into account.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 22

Page 23: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Fig 13.2 Voltage v/s Pressure

(Source: Sabrie Soloman, 1999)

14. PERFORMANCE OF FIBER OPTICS BASED SENSORS IN

COMPARISION WITH TRADITIONAL SENSORS

(a) Firstly fiber optic sensors are used in the areas where traditional sensors cannot

be taken use of.

(b) Fiber optic sensors have much better range and resolution than traditional

sensors.

(c) Measurement in fiber optic sensors is exact and accurate.

(d) Whether in series or in parallel, the fiber optic sensors can be multiplexed

easily.

(e) Cost is less per channel in case of fiber optic sensors.

(f) Fiber optic sensors are secure against electromagnetic interference.

(g) The operation done in fiber optic sensors is passive and it is safe when

compared to traditional sensors.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 23

Page 24: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

15. CONCLUSION:

We can conclude that there are different numbers of uses of fiber optics sensors

using fiber optics technology. The quantities used in measuring fiber optics sensors

are temperature, pressure and strain by updating the fibre so that the quantity to be

measured modulates the intensity based on the losses, polarization, phase, and

wavelength or transit time. Hence fiber optic sensors are more advantageous than

traditional sensors.

16. TRANSMITTER AND RECEIVER PERFORMANCE CHARACTERISTICS

OF LED AND LASER.

Firstly the performance is divided into two types, Laser and LED transmitter

characteristics and next Laser and LED receiver characteristics.

16.1.1 TRANSMITTER PERFORMANCE CHARACTERSITICS OF LED AND

LASER

The transmitter performance is LASER and LED is done in three different

characteristics

(a) Operating Conditions

(b) Electrical Characteristics

(c) Optical Characteristics

OPTICAL FIBER COMMUNICATION SYSTEMSPage 24

Page 25: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

APPENDICES

Table 1- Operating Condition for LED:

Parameter Symbol Min Type Max Unit

Ambient:

Operating Temp

TA 0 70 oC

Supply Voltage Vcc 4.75 5.25 V

Output Load RL 50

Table 2- Operating Conditions for Laser:

Parameter Symbol Min Type Max Unit

Ambient:

Operating Temp

TA 0 -70 oC

Supply Voltage Vcc 3.1 3.5 V

Data output Load RDL 50 Ω

(a) Operating Conditions : The maximum and minimum temperatures of

both LED and LASER are kept same since they can operate without

damage. The voltage given is the operating voltage which is different

from the input voltage and output voltage. In case of LED the minimum

and maximum supply voltage is higher when compared to LASER’s

maximum and minimum supply voltage. And the data output load is

same in both operating conditions.

Table 3- Electrical Characteristics of LED:

Parameter Sym

bol

Min Type Max Unit

Supply current ICC 145 185 mA

Power Dissipation PDISS 0.76 0.97 W

I/P current- Low IIL -350 0 -1.475 µA

OPTICAL FIBER COMMUNICATION SYSTEMSPage 25

Page 26: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

I/P current-High IIH 14 350 µA

Table 4- Electrical Characteristics of Laser:

Parameter Sym

bol

Min Type Max Unit

Supply current ICC 145 185 mA

Power Dissipation PDISS 0.76 0.97 W

Data o/p Rise time tr 125 150 ps

Data o/p fall time tf 125 150 ps

(b) Electrical Characteristics : It consists of the requirements of supply

current, data input and power dissipated by the device, that is power

consumption. The maximum supply current is higher in LED when

compared to LASER’s maximum supply current. The maximum power

dissipation is lower in LASER when compared to LED’s maximum

power dissipation.

Table 5- Optical Characteristics of Laser:

Parameter Symbol Min Type Max Unit

Center wavelength λc 1260 1360 nm

Spectral width Ϭ 1.8 4 nm rms

Optical rise time tr 30 70 ps

Optical fall time tf 150 225 ps

(c) Optical Characteristics : Here drive current plays an important role, since

the output depends on it. The laser operates with an insufficient LED

when the drive current is low. The action of the lasing begins when it

crosses the threshold value.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 26

Page 27: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

16.1.2 RECEIVER PERFORMANCE CHARACTERSITICS OF LED AND

LASER:

The receiver performance is LASER and LED is done in three different

characteristics.

(a) Operating Conditions

(b) Electrical Characteristics

(c) Optical Characteristics

Table 6- Operating Conditions of LED:

Parameter Symbol Min Type Max Unit

Operating Temp TA 0 70 0C

Supply voltage VCC 4.75 5.25 V

Output Load RL 50 Ω

Table 7- Operating Conditions of Laser:

Parameter Symbol Min Type Max Unit

Operating Temp TA 0 +70 0C

Supply voltage VCC 3.1 3.5 V

Data Output Load RDL 50 Ω

(a) Operating Conditions : It describes the maximum and minimum

temperature and range of the voltages by which the device can operate

without damaging. The minimum and maximum supply voltage in

LASER is lower when compared to LED’s minimum and maximum

supply voltage. And the ambient operating temperature is same for both.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 27

Page 28: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Table 8- Electrical Characteristics of LED:

Parameter Sym

bol

Min Type Max Unit

Supply current ICC 82 145 mA

Power Dissipation PDISS 0.3 0.5 W

Data o/p Rise time tr 0.35 2.2 ps

Data o/p fall time tf 0.35 2.2 ps

Table 9- Electrical Characteristics of Laser:

Parameter Sym

bol

Min Type Max Unit

Supply current ICC 115 140 mA

Power Dissipation PDISS 0.38 0.49 W

Data o/p Rise time tr 125 150 ps

Data o/p fall time tf 125 150 ps

(b) Electrical Characteristics : It deals with supply current requirements,

data output characteristics and power dissipated by the device. The

maximum supply current is slightly greater in LED performance when

compared to LASERS maximum supply current. Hence LED maximum

supply current is higher.

Table 10- Optical Characteristics of LED:

Parameter Symbol Min Type Max Unit

Optical i/p

Power maximum

PIN MAX -14 -11.8 dBm avg.

OPTICAL FIBER COMMUNICATION SYSTEMSPage 28

Page 29: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Operating wavelength I 1270 1380 nm

Table 11- Optical Characteristics of Laser:

Parameter Symbol Min Type Max

Receiver sensitivity PIN Min -23 -19

Receiver overload PIN Max -3 +1

i/p operating wavelength Λ 1260 1570

(c) Optical Characteristics : In LED performance characteristics it includes

minimum optical input power, maximum optical input power and

operating wavelength whereas in LASER’s performance characteristics

it includes output power, wavelength, spectral width and back reflection

sensitivity. The minimum operating wavelength in LED is higher

when compared to LASER’s minimum operating wavelength. And

maximum operating wavelength in LASER is higher when compared

to LED’s operating wavelength.

16.2 COMPARISION OF LED SYSTEM AND LASER SYSTEM:

Parameter LED LASER

Data Rate

Transmission Distance

Circuit Complexity

Cost

Life cycle

Power output

Coherence

Applications

Low

Smaller

Simplex

Low

Small

Low output

Incoherent

Moderate Distance

Low data rate

High

Greater

Complex

High

Very large

High output

Coherent

Long Distance

High data rate

OPTICAL FIBER COMMUNICATION SYSTEMSPage 29

Page 30: OFC aman riz

Optical Fiber Communication Systems Losses And Sensor Applications

Generally LED is used for smaller transmission distances so low data rates where

as LASER is used for greater transmission distances so high data rates.

17. References:

1. (James N. Downing, 2005, “Fiber-Optic Communications”, ISBN: 1-4018-

6635-2)

2. (V.S. Bagad, 2008, “Optical Communications”, ISBN: 9788184314823)

3. (Bob Chomycz, 2009, “Planning Fiber Optic Networks”, ISBN: 978-0-07-

149919-4)

4. (John M. Senior, 1992, “Optical Fiber Communcations Principles and

Practice”, ISBN: 978-0-13-032681-2)

5. (K.T.V. Grattan and B.T. Meggitt, 1999, “Optical Fiber Sensor Technlogy”,

ISBN: 0-412-82570-8)

6. (Francis T.S. Yu and Shizhuo Yin, 2002, “Fiber Optic Sensors”, ISBN: 0-8247-

0732-X)

7. (Sabrie Soloman, 1999, “Sensor Handbook”, ISBN: 978-0-07-160570-0)

8. (Michael Bass and Eric W. Van Stryland, 2002, “Fiber Optics Handbook: fiber,

devices and systems for optical communication”, ISBN: 0-07-138623-8)

OPTICAL FIBER COMMUNICATION SYSTEMSPage 30


Recommended