2014 ECHO Bearcat saleshandbook

2 www.bearcatproducts.com

Horsepower Conversion Chart .............................3 Who Uses What ................................................4

Frequently Asked Questions All ECHO Bear Cat Products ...........................5-9Product Noise Levels .....................................10Chipper Commonalities ...................................11

CHIPPER/SHREDDERS2" – Model SC2170 ........................................123" – Models SC3206, SC3265 SC3305, SC3305E & SC3342 ...................13-14

CHIPPER/SHREDDER/BLOWER 5" – Model SC5720B ......................................15

CHIPPERS 4" – Model CH4400 ........................................16 5" – Model CH5653 ........................................17 6" – Models CH611DH & CH6730H ............18-19 8" – Turntable Models CH8720iH & CH8993H .........................20-21 9" – Models CH911DH & CH922DH ............22-23

PTO MACHINES 5" – Model SC5540 - Chipper/Shredder ............24 5" – Model SC5540B - Chipper/Shredder/Blower .................................254.5" – Model CH45540 ...................................26 4.5" – Models CH5540H & CH5540 ................27 8" – Model CH8540 ........................................28 9" – Models CH9540H & CHF9540H ..........29-30

SKID STEER CHIPPERS 4.5"- 8"

Models CH450H, CH500H & CH800H .............31

LOG SPLITTERS Models – LS22 & LS27 ...................................32

WHEELED TRIMMERS WT190, WT190T, WT190S .............................33Accessories ....................................................34

STUMP GRINDER Model – SG340 ..............................................35

WHEELED VACUUMS Models – WV190, WV190S, WV160 & WV160S .........................................36

DEBRIS LOADERS Models – DL8390, DL10570 ...........................37 Models – DL12653, DL12720 .........................38

GEARECHO Bear Cat Gear .......................................39

WARRANTY / PRODUCT CHARTS WARRANTY U.S. AND CANADA Current Models ...................................40-41 Non-Current Models ............................42-43

WARRANTY OUTSIDE U.S. AND CANADA Current Models ...................................44-45 Non-Current Models ............................46-47

Belts Reference Guide ....................................48 Rotor, Shredder/Chipper Replacement Kits ........49 Blade Kits Chart ........................................50-51

ACCESSORIES ..........................................52-59

TABLE OF CONTENTS

3888.625.4520

HP to cc CONVERSION CHART

*A non-current ECHO Bear Cat model number **Horsepower rating based on Engine Manufacturer at time of manufacture

GASOLINE ENGINES

Engine Manufacturer Engine Type cc Gross HP kW Model Number

Briggs & Stratton Horizontal 148 3.5** 2.6 70530*

Briggs & Stratton Vertical - 5** 3.7 74050*, 73350*

Honda Vertical-GCV - 5** 3.7 75050*, 75350*

Subaru Horizontal 170 5.7 4.3 SC2170, LS22

Honda Vertical-GCV 160 4.4 3.3 WT160S (73455), WT160T (74455), WV160, WV160S

Subaru Vertical 190 5.5 4.1 WT24, WT24S, WT24T

Briggs & Stratton Vertical-Intek 190 6** 4.8 WV190* (75060), WV190S* (75360)

Briggs & Stratton Vertical-Quantum 190 6.5** 4.8 WT190* (75065), WT190T* (76065), WT190S* (75365)

Briggs & Stratton Vertical/Elec.-Quantum 190 6.5** 4.8 WT190SE (73265)*

Briggs & Stratton Horizontal 205 5.5** 4.1 SC3206 (70050), SC2206

Subaru Horizontal 210 7 5.2 LS27

Honda Horizontal/Elec.-GX 242 8** 6.0 70385*

Subaru Horizontal 265 9 6.7 SC3265

Honda Horizontal-GX 270 8.5 6.4 SC3270 (70380)*, SC3270T (70580)*

Briggs & Stratton Horizontal/Elec. 305 8** 6.0 SC3305E (70085)

Briggs & Stratton Horizontal 305 8** 6.0 SC3305 (70080)

Briggs & Stratton Horizontal/IC 305 8** 6.0 70180*

Honda Vertical-GXV 340 8.9 6.6 SG340 (73711), 75011*

Honda Vertical/Elec.-GXV 340 8.9 6.6 75111*

Briggs & Stratton Horizontal-Intek 342 11** 8.3 SC3342 (75311)

Honda Horizontal-GX 390 11.7 8.7 DL8390, CH4390 (73413)*

Subaru Horizontal 404 14 10.4 CH4400

Briggs & Stratton Horizontal Vanguard 570 18 13.4 DL10570

Honda Horizontal/Elec.-GX 614 20** 14.9 SC5614 (71020)*, CH6614 (71620)*, CH6614H (72620)*

Subaru Horizontal/Elec. 653 22 16.4 CH5653,DL12653

Honda Horizontal/Elec.-GX 670 24** 17.9 CH6670H (76624)*, CH8670H (76824)*, SC5670 (75524)*, DL12670 (75124)*

Subaru Horizontal/Elec. 720 25 18.6 DL12720,SC5720B

Subaru Horizontal/Elec./Fuel Injected 720 28 20.9 CH8720iH

Briggs & Stratton Horizontal/Elec.-Vanguard 993 35 26.1 CH6993H (76635)*, CH8993H (76835)

Kohler Horizontal/Elec. 730 25 18.6 CH6730H

DIESEL ENGINESEngine Manufacturer Engine Type Liters Gross

HP kW Model Number

Kubota 1105/Mech. 1.1 25 18.5 CH611DH (76628)

Kubota 1105/Mech. 1.1 25 18.5 CH911DH (72928)

Kubota 2203/Mech. 2.2 48 35.9 CH922DH (74950)


Industry Product Used for

Ag - SpecialtyChipper/Shredder

Tobacco stalks

Animal bedding

Wheeled Vacuum Stable clean up

Cemetery

Chipper/Shredder Brush and tree pruning

Wheeled Trimmer Aesthetics

Wheeled Vacuum Leaf removal

FarmingChipper Shelter belt

clean out

Wheeled Trimmer Fence line clean up

Golf Course

Chipper Disposal of broken branches and fallen trees

Chipper/Shredder Create mulch for landscaping

Wheeled TrimmerHeavy grass and weed cleaning for ponds and creeks

Wheeled Vacuum Grass clipping tidy

Grounds and Maintenance

Chipper/Shredder Brush/hedge clean up

Wheeled Trimmer Fence clean up

Wheeled Vacuum Parking lots and stadium clean up

Debris LoaderCollecting grass

clippings and leaf removal

Home Owner with Acreage

Chipper/ShredderYard maintenance

Pruning

Wheeled TrimmerFence line

Riding trails


Industry Product Used for

Landscaper

Chipper Job site clean up

Chipper/ShredderJob site clean up

Create mulch


Debris Loader Leaf clean up

Municipalities

ChipperStorm damage

Palm frawn disposal

Wheeled Trimmer Overpass, road side maintenance

Wheeled Vacuum City park clean up

Debris LoaderStreet clean up

Leaf pick up

NurseriesChipper/Shredder

Dead plant recycling/moisture

control

Wheeled Trimmer Tree plots

Parks and Rec

Chipper/Shredder Trail maintenance

ChipperProperty

maintenance clean up

Wheeled TrimmerTrail maintenance

Fence lines

Wheeled Vacuum Parking lot clean up

Rental

Chipper/Shredder Compost/home owner clean up


Stump Grinder Stump removal

Tree Service Chipper

Refuse reduction

Air quality protection

Power line clearing

Easements clearing

ECHO Bear Cat has a wide range of products to get the job done!

WHO USES WHAT

5888.625.4520

FAQ

CHIPPER/SHREDDERSMODELS: SC2170, SC3206, SC3265, SC3305, SC3305E**, SC3342, SC5540, SC5540B* & SC5720B**

What are these machines designed for? The ECHO Bear Cat chipper/shredders are designed to effectively reduce the volume of wood, leaves and other organic material.

When should I chip? If you don’t plan on composting the material, material is green and stringy or larger than .75" in diameter.

When should I shred? If you plan on composting or if the material is smaller than .75", use the shredder. Shredding is also an efficient way to reduce the volume of leaves or prunings.

How long will the chipper blades last? Depending on the type of wood, age and cleanliness, chipper blades will work well for between 5-15 hours. Dry, dirty wood will dull the blades faster. Alternate dry and wet material to extend blade life.

What is the maximum size of material will these machines chip or shred? ECHO Bear Cat 2" chipper/shredders will chip up to 2" (5cm) and shred up to .75" (2cm) diameter material. ECHO Bear Cat 3" chipper/shredders will chip up to 3" (8cm) and shred up to .75" (2cm) diameter material. ECHO Bear Cat 5" chipper/shredders will chip up to 5" (13cm) and shred up to .75" (2cm) diameter material.

Do not attempt to put material larger than .75" in diameter into the shredder hopper. Doing so may cause machine failure and will void the warranty. *PTO Machines

**Electric start models do not include battery.

LOG SPLITTERSMODELS: LS22 & LS27

What is the cycle time? The LS22 has a cycle time of 12 seconds and the LS27 has a cycle time of 14 seconds.

Does my splitter come with hydraulic fluid? The hydraulic system on this log splitter comes filled with high performance Automatic Transmission Fluid (ATF) to accommodate operation in temperatures below 32 degrees F (0 degrees C). When adding or replacing ATF, use a Dexron® III or Mercon® qualified product. Check the fluid on level ground with the jack stand in the down position. DO NOT MIX HYDRAULIC FLUID WITH ATF. THIS MAY DAMAGE THE SYSTEM AND COULD VOID WARRANTY. DO NOT OVERFILL. FILL THE HYDRAULIC FLUID TANK WITH THE RAM RETRACTED.

What size logs can I split? The maximum length of log that you can split is 24" (60.9cm) long. You can split larger diameter logs with the unit in the vertical position.

How difficult is it to perform maintenance on the machine? ECHO Bear Cat products are designed with ease of maintenance in mind. Proper maintenance is vital and should be performed routinely with blades, belts and bearings being most important.


FAQ

WHEELED TRIMMERSMODELS: WT190, WT190T & WT190S

Can I operate the Wheeled Trimmer on a hillside? The ECHO Bear Cat Wheeled Trimmer is capable of continuous operation on a slope not to exceed 15 degrees. Limited operation on slopes greater than 15 degrees is allowed.

Do the engines have an oil pump? No. The engines obtain lubrication from a “Splash Lube” system.

How do I change the trimming line? To wrap the cutting string in the standard configuration, feed the cutting string through the second hole on either end of the trimmer head leaving approximately 8 inches for the cutting surface. Total recommended string length is 20-1/2". Continue by weaving the cutting string through the first hole directly beside the second hole. Loop the cutting string back and feed through the first hole on the opposite end of the trimmer head. Pull the cutting string tight. Feed through the remaining second hole and pull the cutting string tight. The cutting strings in the middle two holes should be the same length. If the length differs, cut to an even length. It may be necessary to remove pieces of broken or worn string before new string can be properly installed.

How many speeds does the Self-Propelled Wheeled Trimmer (WT190S) have and how fast does it go? There are three separate gears on the transmission of the Self-Propelled Wheeled Trimmers, and the speeds range from 1 to 3 mph.

What is the Sabre Tooth Blade and Triple Blade Brush Cutter used for? The Sabre Tooth Blade (14" dia.) is designed to be used for cutting small trees, saplings, bushes etc. up to 4" in diameter. The Nylon Blade Kit is designed for the heavy grass, weeds and brush growth.

Do the Sabre Tooth blade and Triple Blade Brush Cutter fit all WT190 models? Yes. By removing the mow ball both accessories will work and can be height adjusted to preference.


STUMP GRINDER MODEL: SG340

What is the application of the Stump Grinder? The ECHO Bear Cat Stump Grinder is designed with a compact 23" wheel base, enabling it to be used on stumps found in places large stump grinders cannot get to.

How do I engage the Stump Grinder? Position the stump grinder so the cutter head is adjacent to the stump. Start the stump grinder and hold up the bottom bail so it doesn't shut off. Pull the top bail to the handle and hold it there to activate the left wheel brake, holding it so it does not turn. Gradually, using the locked left tire as a pivot point, slowly pivot the cutter head until the cutting teeth contact the stump. Pivot the stump grinder on the left wheel in a slow, smooth sweeping motion from left to right as the teeth grind the stump. Do not force the cutting teeth. Check position by watching through the screen opening. Grind the stump down to a maximum of 4 inches below ground level.


7888.625.4520

FAQ

CHIPPERSMODELS: CH4400, CH45540, CH5653, CH5540, CH5540H, CH611DH, CH6730H, CH8540, CH8993H, CH8720iH, CH9540H, CHF9540H, CH911DH & CH922DH

What are these machines designed for? The ECHO Bear Cat chipper is designed to effectively reduce the volume of wood, branches, and other organic material. The typical application for this product group is anywhere from light commercial to municipalities and/or rental.

What types of chippers are available? ECHO Bear Cat makes chippers with gravity or hydraulic feed, powered by an engine package or a tractor PTO. A hydraulic feed machine has a hydraulic driven feed roller to efficiently feed branches to the chipper rotor.

When should I buy a gravity feed machine? If you have an infrequent need for a chipper and time is not a factor, a gravity feed machine will fit your needs.

When should I buy a hydraulic feed machine? If time or efficiency is an issue, a hydraulic feed chipper allows you to be more productive.

What does it mean when you say hydraulic feed chippers feature an "Auto Feed" system? "Auto Feed" refers to the way the system senses if the rotor has slowed down too much for maximum chipping performance. When this happens, the feed roller stops feeding the material, allowing the engine and rotor RPM to recover. Once the engine and rotor RPM have recovered sufficiently, the feed roller reengages and begins feeding material again. It has also been referred to as the "try again" feature.

How long will the chipper blades last? Depending on the type of wood, age and cleanliness, chipper blades will work well for between 5-15 hours. Dry, dirty wood will dull the blades faster. Alternate dry and wet material to extend blade life. Hydraulic feed chippers will have longer blade life.


Will electric start chippers include the starting battery? No. ECHO Bear Cat products are not shipped with a battery and will need to be purchased separately.

POWER TAKE OFF (PTO) MACHINES MODELS: CH45540, CH5540, CH5540H, SC5540, SC5540B, CH8540, CH9540H & CHF9540H

When do I buy a chipper powered by a tractor Power Take Off (PTO) vs. an engine-driven unit? If you own a tractor a PTO chipper is a smart economic choice.

What are the tractor requirements for these chippers and chipper/shredders? The ECHO Bear Cat 4.5" chipper requires a tractor with PTO hp ranging from 15hp to 28hp. The ECHO Bear Cat 5" chippers and chipper/shredders require a tractor with PTO hp ranging from 25hp to 45hp. The ECHO Bear Cat 8" and 9" chippers require a tractor with PTO hp ranging from 35hp to 60hp.

Will the chipper fit my tractor? The ECHO Bear Cat chippers and chipper/shredders are designed to fit all Category 1 three-point hitches. Chipper weight and tractor hp needs to be taken into consideration. All Chipper models fit a Category 1 Quick Hitch.


FAQ

SKID STEER CHIPPERS MODELS: CH450H, CH500H & CH800H

What is this machine designed for? The ECHO Bear Cat chipper is designed to effectively reduce wood, brush, and other organic material while using your skid steer as the power unit.

What is the capacity and hydraulic flow requirements of these machines? The CH450H has a maximum capacity of 4.5" (11cm) and requires at least 11 to 15 GPM (41.6 to 56.8 LPM) on a mini skid steer. The CH500H has a maximum capacity of 5" (13cm) and requires at least 15 to 22 GPM (56.7 to 83.3 LPM) on a low-flow skid steer. The CH800H has a maximum capacity of 8" (20cm) and requires at least 25 to 38 GPM (94.6 to 43.8 LPM) on a hi-flow skid steer.

Will the chipper fit my skid steer? The ECHO Bear Cat CH500H and CH800H skid steer chippers are equipped with universal attachment ends, capable of hooking up to most skid steers. The CH450H is designed to mount to mini skid steers.

How long will the chipper blades last? Depending on the type of wood, age and cleanliness, chipper blades will work well for between 5-15 hours. Dry, dirty wood will dull the blades faster. Alternate dry and wet material to extend blade life. Hydraulic feed chippers will have longer blade life.


WHEELED VACUUMSMODELS: WV190, WV190S, WV160 & WV160S

Where can I use the Wheeled Vacuum? The Wheeled Vacuum is designed to be used for residential, commercial or municipal pickup of leaves, grass or other light debris.

How much reduction of debris will I get? There is not much reduction; however, by passing through a six-bladed fan into the bag some natural breakage occurs allowing the five-bushel bag to be filled. Reduction through compaction will happen.

Is it hard to push the Wheeled Vacuum on turf? The large wheels have ball bearing hubs that allow easy movement.

How many speeds do the Self-Propelled Wheeled Vacuums have and how fast does it go? There are three separate gears on the transmission of the Self-Propelled Wheeled Vacuum, and the speed range is 1 to 3 mph.

How many height adjustments does the Wheeled Vacuum have? The Wheeled Vacuum can be adjusted into four different nozzle settings ranging from .25" - 4.5" (.64cm-11.4cm) to accommodate all types of terrain.

What do I use the optional 4" (10.1cm) Vacuum Hose Kit for? This hose kit is designed to allow vacuuming hard to reach places.


9888.625.4520

FAQ

DEBRIS LOADERSMODELS: DL8390, DL10570, DL12653 & DL12720

What is the application for the Debris Loader? The Debris Loader is used for commercial or municipal pickup of leaves, grass, or other light debris.

How much reduction of debris will I get? There is very limited reduction of the material due to the design for compaction vs. reduction. The Debris Loader is designed to effectively load leaves, grass, or other light debris from the ground to a vehicle collection bin.

Is there a rental application for this machine? Yes. Commercial landscapers and municipalities will have a seasonal need for this piece of equipment.


Will electric start Debris Loaders include the starting battery? No. ECHO Bear Cat products are not shipped with a battery and will need to be purchased separately.

I have a chipper that requires the belt to be engaged. How do I engage and disengage the belt without it squealing and causing damage to the belt or other drive components?ENGAGING THE BELT:

1. AFTER engine is warmed and ready for use, move the throttle control back down to approximately 25% of full throttle.

2. When engine is running at approximately 25% of full throttle, SLOWLY engage belt by using the belt engagement .

DO NOT engage the belt with engine running at high RPM. Engaging belt while engine is running at high RPM WILL result in significant belt squealing and possible damage.

Engaging belt while engine is running at high RPM may also damage vital drive components of the chipper or chipper/shredder,

3. If the chipper engine stalls while engaging the belt, return the belt engagement back to the START position, restart engine, SLIGHTLY increase throttle and attempt engagement again.

4. Once the belt is engaged, SLOWLY increase throttle to 100% or full throttle.

5. ALWAYS run the machine at 100% or full throttle when chipping or shredding material.

ENGINE SHUTDOWN/BELT DISENGAGEMENT:

1. WITH THE BELT STILL ENGAGED, SLOWLY move the throttle to the SLOW position.

2. Allow the engine to run at slow idle for 30-60 seconds. This will slow the rotor down to the same RPM as the engine.

3. Stop the engine by moving the throttle to the STOP position or turning off the ignition switch.

4. Allow rotor to come to a complete stop.

5. Once the engine is off and the rotor has completely stopped, the belt can be disengaged by moving the belt engagement back to the START position.

NEVER disengage the belt as part of the stopping or shut down process. The belt should remain engaged during the entire shut-down process.

Leaving the belt engaged is a vital part of proper shutdown and ensures the rotor stops spinning in conjunction with the engine shutting off.


PRODUCT NOISE LEVELS

Model Description dB (Pressure)

dB(Power Level)

CHIPPER/SHREDDERSSC2170 2" (5cm) Capacity – Subaru SP 170cc 97 111

SC3206 3" (7.6cm) Capacity – Briggs & Stratton OHV 205cc 97 111

SC3265 3" (7.6cm) Capacity – Subaru EX 265cc 97 111


SC3305E 3" (7.6cm) Capacity – Briggs & Stratton OHV 305cc, Electric Start 98 112


CHIPPER/SHREDDER/BLOWERSC5720B 5" (13cm) Capacity Chipper/Shredder/Blower Subaru 720cc 97 120

LOG SPLITTERSLS22 Subaru SP 170cc N/A N/A

LS27 Subaru SP 210cc N/A N/A

WHEELED TRIMMERSWT190 Briggs & Stratton Quantum 190cc 87 101

WT190T Briggs & Stratton Quantum 190cc 87 101

WT190S Briggs & Stratton Quantum 190cc 87 101

STUMPGRINDERSG340 Honda 340cc 73 87

CHIPPERSCH4400 4.5" (11cm) Subaru EX 404cc 93 107

CH5653 5" (13cm) Capacity – Subaru EH 653cc 92 109

CH611DH 6" (15cm) Capacity – Kubota Diesel 1.1 Liter with Hydralic Feed 94 111

CH6730H 6" (15cm) Capacity – Kohler Command Pro 730cc with Hydraulic feed 94 117

CH8720iH 8" (20cm) Capacity – Subaru 720cc – Turntable with Hydraulic Feed 96 114

CH8993H 8" (20cm) Capacity – Briggs & Stratton Vanguard 993cc – Turntable with Hydraulic Feed 94 114

CH911DH 9" (23cm) Capacity – Kubota 1.1 Liter Diesel with Hydraulic Feed 95 112

CH922DH 9" (23cm) Capacity – Kubota 2.2 Liter with Hydraulic Feed 95 112

PTO CHIPPERS AND CHIPPER/SHREDDERSCH45540 4.5" (11cm) Capacity – 540 PTO – 15-28 hp Input Range 87* 107

CH5540 5" (13cm) Capacity – 540 PTO – 25-45 hp Input Range 86* 103

CH5540H 5" (13cm) Capacity – 540 PTO with Hydraulic Feed – 25-45 hp 86* 103

SC5540 5" (13cm) Capacity – 540 PTO – Chipper/Shredder – 25-45 hp Input Range 99* 113

SC5540B 5" (13cm) Capacity – 540 PTO – Chipper/Shredder – PTO - 25-45 hp 99* 113

CH8540 8" (20cm) Capacity – 540 PTO – 35-60 hp Input Range 95* 112

CH9540H 9" (23cm) Capacity – 540 PTO with Hydraulic Feed - 35-60 hp 95* 112

CHF9540H 9" (23cm) Capacity – 540 PTO with Hydraulic Feed - 35-60 hp 95* 112

WHEELED VACUUMSWV160 160cc Honda OHC 84 98

WV160S 160cc Honda OHC - Self-Propelled 84 98

WV190 190cc Briggs & Stratton OHV 84 98

WV190S 190cc Briggs & Stratton OHV - Self-Propelled 84 98

DEBRIS LOADERSDL8390 Honda GX 390cc – 8" (20.3cm) Intake 116 134

DL10570 Briggs & Stratton Vanguard 570cc – 10" (25.4cm) Intake 120 138

DL12653 Subaru EH 653cc – 12" (30.5cm) Intake 97 120

DL12720 Subaru EH 720cc – 12" (30.5cm) Intake 99 122

These values were obtained using harmonized EN ISO 3744:2010*based off towable model

11888.625.4520

CHIPPERS

14" (35.6cm) rotor weighing 49 lbs. (22.2kg) fully assembled• 1" (2.5cm) thick machine balanced cantilever rotor• Models: CH4400, CH45540 & CH450H• Standard 4.5" x 9" (11.4cm x 22.9cm) discharge chute. Optional discharge chute is 4.5" (11.4cm) square• 13" x 14.5" (33cm x 36.8cm) feed chute• Two reversible heat-treated steel chipper blades• Four-sided cutter bar/anvil• Chipper Blade Kit: P/N: 76295-00

20" (50.8cm) rotor weighing 140 lbs. (63.5kg) fully assembled• 1.25" (3.2cm) thick machine balanced• 4" (10cm) and 5" (13cm) chippers, Models CH5540, CH500H, CH5540H & CH5653 – same chipper body• 6" (15cm) discharge chute rotating 360 degrees• 5.5" x 7" (14cm x 17.8cm) feed opening• Reversible heat-treated steel chipper blades.• Four-sided adjustable steel anvil/cutter bar• Double-banded belt drive, except model CH500H is hydraulic driven – no belts• Chipper Blade Kit: P/N: 72493

26" (66cm) rotor weighing 165 lbs. (74.8kg) fully assembled• 1" (2.5cm) thick machine balanced cantilever rotor• Chipper Models: CH6730H & CH611DH• 6.7" (17cm) square discharge chute• 6.5" x 13.5" (16.5cm x 34.3cm) feed chute for easy feeding of limbs• Four reversible heat-treated steel chipper blades• Four-sided anvil/cutter bar mounted on the side of the feed chute• Triple-banded belt• New style local sensing two-stage pump with live hydraulics• SmartFeed Sensor• Hand-operated belt engagement lever• Chipper Blade Kit: P/N: 76293-00

30" (76.2cm) rotor weighing 275 lbs. (124.7kg) fully assembled• 1.25" (3.2cm) thick machine balanced• 9" (23cm) machine – Model CHF9540H• 6" (15cm) diameter square discharge. Discharges toward the ground from a height of 34" (86cm)• 9" x 9" (23cm x 23cm) feed throat opening• 16 reversible heat-treated steel chipper blades • Four-sided adjustable steel anvil/cutter bar• Triple-banded belt drive• Chipper Blade Kit: P/N: 74830-00

30" (76.2cm) rotor weighing 275 lbs. (124.7kg) fully assembled• 1.25" (3.2cm) thick machine balanced• 8" (20.3cm) and 9" (23cm) machines• Models CH800H, CH8720iH, CH8993H, CH8540, CH9540H, CH911DH & CH922DH – same chipper body• 8" (20.3cm) discharge chute rotating 360 degrees• 9" x 9" (23cm x 23cm) feed throat opening• Four reversible heat-treated steel chipper blades• Four-sided adjustable steel anvil/cutter bar• Triple-banded belt drive, except model CH800H is hydraulic driven – no belts• Chipper Blade Kit: P/N: 76293-00

CHIPPER COMMONALITIES


CHIPPER/SHREDDERS

ENGINE• Subaru SP 170cc

• Max torque: 8.3 ft-lbs at 2,500 rpm, runs at 3,800 rpm

FUEL CAPACITY• .9 gal. (3.4 liters)

DIRECT DRIVE

FEED CHUTES• Shredder hopper is 16" x 20" (40.6cm x 50.8cm)

• Maximum shredder capacity of up to .75" (2cm)

• Maximum chipper feed size of up to 2" (5cm)

CHIPPING BLADES & SHREDDING KNIVES• Two reversible heat-treated steel chipper blades

• Blade Dimensions: 3.125" x 2" x .25" (8cm x 5cm x .6cm)

• Four reversible Shredder Knives (standard)

• Four additional Shredder Knives optional

CHIPPER/SHREDDER ROTOR ASSEMBLY• Rotor weight is 15 lbs. (6.8kg)

• Rotor turns at 3,800 rpm

• 12.8" diameter (32.6cm)

EASY TO TRANSPORT• Easy grip wide handle

• Weight of machine is distributed evenly throughout

DISCHARGE SCREEN• Comes standard with 1.13" screen (2.9cm)

MACHINE DIMENSIONS AND WEIGHT• LxWxH – 29" x 23" x 50" (74cm x 58cm x 127cm)

• 120 lbs. (54.4kg)

SAFETY• Meets ISO safety decal standards

PARTS & ACCESSORIES• Standard Screen 1.13" (2.8cm) (P/N: 76758-35)

• Fine Screen .75" (2cm) (P/N: 76893-35)

• Wet Debris Screen (P/N: 77639-35)

• Shredder Knives Kit (P/N: 77616-00)

• Additional Shredder Knives Kit (P/N: 77618-00)

• Chipper Blade Kit (P/N: 70738)

• Hour/Tach Kit (P/N: 31605-00)

2" (5cm) CAPACITY CHIPPER/SHREDDERModel: SC2170

.75" FineWet

Debris1.13"

Standard

SC2170 Debris Screens

13888.625.4520

ENGINESSC3206• Briggs & Stratton OHV 206cc• Max torque: 9 ft-lbs. at 2,700 rpm, runs at 3,600 rpm

SC3305• Briggs & Stratton OHV 305cc

• Max torque: 14.5 ft-lbs. at 2,800 rpm, runs at 3,600 rpm

SC3305E• Briggs & Stratton OHV 305cc – Electric Start


SC3265• Subaru EX 265cc


SC3342• Briggs & Stratton OHV 342cc


FUEL CAPACITY• SC3206 - .8 gal (3 liters)

• SC3265 - 1.6 gal (6.1 liters)

• SC3305, SC3305E, SC3342 - 1 gal. (3.8 liters)

CHIPPER/SHREDDER ROTOR ASSEMBLYSC3206• Weighs 21 lbs. (9.5kg)

• Rotates at 3,600 rpm

• 1" (2.5cm) diameter rotor shaft

• 12" diameter (30.4cm)

SC3265, SC3305, SC3305E, SC3342• Weighs 27 lbs. (12.3kg)


• 1" (2.5cm) diameter rotor shaft

• 12" diameter (30.4cm)

CHIPPER BLADES & SHREDDER KNIVES• Two reversible heat-treated chipper steel blades

• Blade Dimensions: LxWxH: 3.125" x 2"x .25" (7.6cm x 5cm x 6cm)

• Eight Reversible Shredder Knives – SC3206

• Twelve Reversible Shredder Knives SC3265, SC3305, SC3305E, SC3342

BEARINGS• Two 1" (2.5cm) greasable bearings with three bolt cast

flanges

BELT DRIVE • With manual belt engagement

• SC3206, SC3305, SC3305E – single belt driven

• SC3265, SC3342 - dual belt driven

• Spring-loaded belt tensioner



• Maximum chipper feed size of up to 3" (7.6cm)

SIDE DISCHARGE• You don’t have to move the equipment as often with a side

discharge as you do with a bottom discharge

• Heavy-duty 7 gauge steel screens available in four different sizes to fit your needs

CONVENIENT TRANSPORTATION• Handle placement for the best control over various terrain,

or tip it back and use the hopper handle for transporting on a smooth surface

• Pneumatic tires feature grease zerks, enabling easy greasing of the hub

3" (7.6cm) CAPACITY CHIPPER/SHREDDERS 1 of 2

Models: SC3206, SC3265, SC3305, SC3305E & SC3342

CHIPPER/SHREDDERS


CHIPPER/SHREDDERS

HEAVY-DUTY CONSTRUCTION• Extra strength and reinforcements in areas that matter

most

• 14 gauge (1.9mm) steel construction

• Built to last with welded construction instead of bolt together.

MACHINE DIMENSIONS

• LxWxH – 40" x 25" x 46" (101cm x 64cm x 117cm)

WEIGHTS

• SC3206 - 195 lbs. (88.5kg)

• SC3265 - 250 lbs. (113.4kg)

• SC3305 - 228 lbs. (103.4kg)

• SC3305E - 240 lbs. (108.9kg)

• SC3342 - 263 lbs. (119.3kg)

PARTS & ACCESSORIES• Two-Wheel Tow Kit (P/N: 77000-00)

• Leaf Tamper (P/N: 70089)

• Debris Bag with Handles (P/N: 17854)

• All Weather Cover (P/N: 70093)

• Chipper Blade Kit (P/N: 70738)

• Tach/Hour Meter (P/N: 31605-00)

• Road Towable Chipper/Shredder Trailer (P/N: 77353-00)

• Supplemental Adapter Kit for models SC3265, SC3305, SC3305E & SC3342 Serial C03477 & below (P/N: 77700-00)

• Supplemental Adapter Kit for model SC3206 Serial C03477 and below (P/N: 77701-00)

PARTS & ACCESSORIES

SC3206

• Screen - Fine .375" (.95cm) (P/N: 77382-12)

• Screen - Medium .75" (2cm) (P/N: 77383-12)

• Screen - Coarse Standard 1.375" (3.5cm) (P/N: 77384-12)

• Screen - Wet Debris (P/N: 77385-12)

• Shredder Knives Kit – SC3206 (P/N: 77589-00)

SC3265, SC3305, SC3305E, SC3342

• Screen - Fine .375" (.95cm) (P/N: 77386-12)

• Screen - Medium .75" (2cm) (P/N: 77387-12)

• Screen - Coarse Standard 1.375" (3.5cm) (P/N: 77388-12)

• Screen - Wet Debris (P/N: 77389-12)

• Blower Attachment (P/N: 70251)

• Shredder Knives Kit (P/N: 70973)

3" (7.6cm) CAPACITY CHIPPER/SHREDDERS 2 of 2

Models: SC3206, SC3265, SC3305, SC3305E & SC3342

A 1.375" debris screen is standard with three others available depending on desired mulch size/type.

.375"

.75"

1.375" Standard

Wet

Debris

Debris Screens

15888.625.4520

CHIPPER/SHREDDER/BLOWER

ENGINE• Subaru EH 720cc


FUEL CAPACITY• 9 gal. (34.1 liters)

CHIPPER/SHREDDER ROTOR ASSEMBLY• Weighs 121 lbs. (54.9kg)

• Machine balanced


• 1.5" (3.8cm)-diameter rotor shaft

• 20.6" (52.3cm) diameter

• Easily accessible through the hinged cover, when open it exposes one half of the rotor for easy access to the chipping blades and makes for easy clean out

CHIPPER BLADES & SHREDDER KNIVES• Four reversible heat-treated chipper steel blades

• Blade Dimensions: 3.125" x 2" x .25" (7.6cm x 5cm x 6cm)

• 36 Shredder Knives

BEARINGS• Two 1.5" (3.8cm) greasable bearings with two bolt

cast flanges

DOUBLE-BANDED BELT DRIVE • Manual belt engagement


FEED CHUTES• Shredder hopper is 13" x 18" (33cm x 48.7cm)



INTEGRATED DISCHARGE • With a 360° rotatable, 6" (15.25cm) diameter steel

tubing with adjustable spout cap allows you to put the chips where you want them the first time

• Discharge height is 92" (234cm)

UNIQUE SCREENLESS SHREDDER• Unique product, self-feed chipper/shredder without a

screen. This greatly reduces the chance of plugging, especially with damp material

HEAVY-DUTY CONSTRUCTION• 7 gauge steel

HIGHWAY TOWABLE• 50" (127cm) tread width (center to center) and 5.3-12

tires with 1,000 lb. (454kg) torsion axle suspension enables the chipper to be easily towed down the highway

TOWING WEIGHT• 930 lbs. (422kg) with fluids at capacity

HITCH• 2" (5cm) ball coupler is standard

MACHINE DIMENSIONS• LxWxH – 92" x 52" x 92" (233cm x 131cm x 233cm)


• Safety chains

• 12 volt tail lights standard

• Meets NATM Certification

PARTS & ACCESSORIES• Chipper Blade Kit (P/N: 72493)

• Shredder Knives Kit (P/N: 77613-00)

5" (13cm) CAPACITY CHIPPER/SHREDDER/BLOWERModels: SC5720B


CHIPPERS4" (10cm) CAPACITY CHIPPER

Model: CH4400

ENGINE• Subaru EX 404cc

• Max torque: 20 ft-lbs. achieved at 2,400 rpm operates at 3,800 rpm

FUEL CAPACITY• 1.85 gal. (7 liters)

14" (35.6cm) DIAMETER CANTILEVER ROTOR• 14" (35.6cm) diameter by 1" (2.5cm) thick rotor

• Weighs 49 lbs. (22.2kg)



• 1.25" (3.2cm) diameter rotor shaft

TWO CHIPPING BLADES• Two reversible heat-treated steel chipper blades

• Blade Dimensions: 5" x 4" x .5" (12.7cm x 10.2cm x 1.3cm)

BEARINGS• Two 1.25" (3.2cm) greasable bearings with

two bolt cast flanges

BELT DRIVE• Double-banded belt drive with manual belt

engagement


ANVIL/CUTTER BAR• Four-sided adjustable to insure good chipping ability

• 5" long x 1.75" wide x .375" thick (12.7cm x 4.4cm x .95cm)

FEED CHUTE• Opening 13" x 15" (33cm x 38cm), 38" (96.5cm)

off the ground

• Feed throat opening is 5" x 5" (12.7cm x 12.7cm)

• Maximum feed size of up to 4" (10cm)

INTEGRATED DISCHARGE• Standard Discharge

4.5" x 9" (11.4cm x 22.9cm) and discharges towards the ground, from a height of 14" (36cm)

• Optional Discharge 4.5" x 4.5" (11.4cm x 11.4cm) square discharge with adjustable deflector, discharges at a height of 55" (140cm)

HEAVY-DUTY CONSTRUCTION• 7 gauge steel throughout housing with welded

construction

• Trailer is made of 7 gauge steel

• Tongue is 2" x 2" (5cm x 5 cm) with 11 gauge wall thickness

HIGHWAY TOWABLE• 43" (109cm) tread width (center to center) and

4.80-8 tires with 1,000 lb. (454kg) torsion axle suspension enables the chipper to be easily towed down the highway

• 12 volt safety and directional lighting and tow chains are standard

TOWING WEIGHT• 536 lbs. (243kg)




• Safety chains



PARTS & ACCESSORIES• Blade Kit (P/N: 76295-00)

• Optional Discharge Chute 4.5" x 4.5" (11.4cm x 11.4cm) (P/N: 74634-00)

• Tach/Hour Meter Kit - Gas (P/N: 31605-00)

17888.625.4520

CHIPPERS5" (13cm) CAPACITY CHIPPER

Model: CH5653

ENGINE• Subaru EH engine 653cc


FUEL CAPACITY• 9 gal. (34.1 liters)

20" (51cm) DIAMETER ROTOR• 20" (51cm) diameter by 1.25" (3.2cm) thick rotor






FOUR CHIPPING BLADES• Four reversible heat-treated steel chipper blades

• Blade Dimensions: 3.1" x 2" x .25" (7.9cm x 5cm x .6cm)

BEARINGS• Two 1.5" (3.8cm) greasable bearings with two bolt cast

flanges

BELT DRIVE• Double-banded belt drive with manual belt engagement


ANVIL/CUTTER BAR• Four-sided adjustable

• 5.6" long x 4" wide x .375" thick (14.2cm x 10.2cm x .95cm)

FEED CHUTE• Opening 27" x 28" (68.6cm x 71.1cm)

43.8" (111cm) off the ground

• Feed throat opening is 5.5" x 6" (14cm x 15.2cm)

• Maximum feed size of up to 5" (12.7cm)

INTEGRATED DISCHARGE• With a 360° rotatable, 6" (15.2cm) diameter steel tubing

with adjustable spout cap allows you to put the chips where you want them the first time

• Discharge height is 95" (2.4m)

HEAVY-DUTY CONSTRUCTION• .25" (6.35cm) steel housing with welded

construction

• Trailer is made of 7 gauge steel

• Tongue is 2" x 2" (5cm x 5 cm) with .25" (6.35mm) wall thickness

HIGHWAY TOWABLE• 44" (112cm) tread width (center to center) and 5.30-12

tires with 1,000 lb. (454kg) torsion axle suspension en-ables the chipper to be easily towed down the highway

• 12 volt safety and directional lighting and tow chains are standard

TOWING WEIGHT• 950 lbs. (431kg)




• Safety chains



PARTS & ACCESSORIES• Blade Kit (P/N: 72493)



CHIPPERS6" (15cm) CAPACITY CANTILEVER CHIPPERS - 1 of 2

Models: CH611DH & CH6730H

ENGINESCH611DH

• Kubota 1.1 Liter Diesel, 69 cu in. (1.1 liter)

• Max torque: 54.2 ft-lbs. achieved at 2,200 rpm

• Operates at 3,220 rpm

CH6730H• Kohler 730cc



FUEL CAPACITY/CONSUMPTION• 9 gal. (34.1 liters)

• Fuel consumption on the Kohler 730cc is estimated at 2.1 gal. (8 liters) per hour at full load

• Fuel consumption on the Kubota 1.1 L is estimated at 1.7 gal. (6.44 liters) per hour at full load

26" (66cm) DIAMETER ROTOR• 26" (66cm) diameter by 1" (2.5cm) thick rotor

• Weighs 165 lbs. (75kg)


• Rotates at 1,780 rpm (CH611DH)

• Rotates at 1,650 rpm (CH6730H)





BEARINGS• Two 1.75" (4.5cm) greasable bearings with four bolt cast

flanges

BELT DRIVE• Triple-banded belt drive with manual belt engagement


ANVIL/CUTTER BAR• Four-sided adjustable anvil to insure good chipping ability

• 6" long x 4" wide x .625" thick (16.5cm x 10.2cm x 1.6cm)

HYDRAULIC FEED SYSTEM• Steel hydraulic reservoir, 4 gal. (15 liters) capacity on

CH611DH and a Nylon hydraulic reservoir, 3 gal. (11.5 liters) capacity on the CH6730H

• Self-contained hydraulic feed system allows you to evenly feed limbs into the chipper

• Variable feed rate on the CH611DH (available as an accessory on the CH6730H) with load sensing 2-stage pump

• Feed rate 0-150 fpm (0-46 m/min) Average 100 fpm (30 m/min)

• Self-contained system with infinite speed settings, dedicated neutral and full reverse, pump output 6.6 GPM (25 LPM) and 4hp with maximum pressure and maximum flow, however this is rarely required

• Feed system operates under 2,500 psi

• Single 15" (38cm) diameter top feed roller

• 2-stage pump

PLUS+1® ELECTRONIC CONTROLLER• Smart feed with automatic “try again” feature to clear jams

• Maximizes chipping efficiency and manpower

• Minimizes fuel consumption

• Provides an Amber code that alerts the operator every 15 hours to inspect chipping blades

FEED CHUTE• Opening 33" x 37" (84cm x 94cm) tray 30"

(76.2cm) off the ground

• Feed throat opening is 6.5" x 13" (16.5cm x 33cm)

• 90° feed angle

• Maximum feed size of up to 6" (15.2cm)

INTEGRATED DISCHARGECH6730H

• With a 360° rotatable, 6" (15.2cm) diameter steel tubing with adjustable spout cap


CH611DH

• With a 360° rotatable, 6.7" (17cm) square steel chute with screw-type adjustable spout cap


19888.625.4520

CHIPPERS

HEAVY-DUTY CONSTRUCTION• .25" (6.35cm) housing with welded construction

• Feed table is 10 gauge steel on the CH6730H and 7 gauge steel on the CH611DH

• Tongue is 3" x 3" (7.6cm x 7.6 cm) with 11 gauge wall thickness

HIGHWAY TOWABLECH6730H

• 50" (127cm) tread width (center to center) and P205-75R14 tires with 1,800 lb (816kg) torsion axle suspension

CH611DH

• 50" (127cm) tread width (center to center) and P215-75R15 tires with 2,500 lb. (1030kg) torsion axle suspension

TOWING WEIGHT• CH611DH – 2,300 lbs. (1,043kg)

• CH6730H – 1,635 lbs. (742kg)


• Height adjustable coupler has 3 positions in 2" (5cm) increments (CH611DH)

• CH611DH has a telescoping tongue length may be adjusted up to 18" (45cm)

ADJUSTABLE TONGUE JACK• Roller wheel with 850 lbs. (385kg) rating

• Adjustable jack allows one person to easily maneuver the chipper around and hook up to a vehicle

MACHINE DIMENSIONSCH611DH• LxWxH – 143" x 59" x 93" (363cm x 150cm x 236cm)

CH6730H• LxWxH – 126" x 57" x 104" (320cm x 145cm x 264cm)


• Safety chains




• 2 5/16" Coupler (P/N: 14519-00)

• Pintle Hitch (P/N: 14900-00)

• Spare Tire Kit (CH611DH)(P/N: 75291-00)


• Knee Bar (P/N: 76945-00)

• Adjustable Feed Speed Sensor Kit (P/N: 76820-00)

6" (15cm) CAPACITY CANTILEVER CHIPPERS - 2 of 2

Models: CH611DH & CH6730H

Cantilever-Mounted Rotor on Select Models


CHIPPERS

ENGINESCH8720iH

• EFI Subaru EH 720cc, Fuel injected

• Max torque: 38.5 ft-lbs at 2,800 rpm


CH8993H

• Briggs & Stratton Vanguard 993cc

• Max torque: 52.4 ft-lbs at 2,350 rpm


FUEL CAPACITY/CONSUMPTION• 9 gal (34.1 liters)

• Fuel consumption on the Briggs & Stratton 993cc is estimated at 3 gal. (11.3 liters) per hour at full load

• Fuel consumption on the EFI Subaru EH 720cc is estimated at 1.5 gal (5.7 liters) per hour at full load







FOUR CHIPPING BLADES • Four reversible heat-treated steel chipper blades


BEARINGS• Two 1.75" (4.5cm) greasable bearings with 4 bolt cast

flanges





HYDRAULIC FEED SYSTEM• Steel hydraulic reservoir, 3 gal. (11.5 liters) capacity


• Variable feed rate with load sensing 2-stage pump


• Self-contained system with infinite speed settings, dedicated neutral and full reverse, pump output 6.6 GPM (25 LPM) and 4hp with maximum pressure and maximum flow, however this is rarely required



• 2-stage pump

8" (20cm) CAPACITY TURNTABLE CHIPPERS - 1 of 2

Models: CH8720iH & CH8993H

New Formed Rotor Paddles

21888.625.4520

CHIPPERS




• Provides an Amber code that alerts the operator every 15 hours to change chipping blades

FEED CHUTE• Opening 30" x 31" (76cm x 79cm)

Tray 27" (68cm) off the ground

• Feed throat opening is 9" x 9" (23cm x 23cm)

• 90° Feed Angle


INTEGRATED DISCHARGE• With a 360° rotatable, 8" (20cm) diameter steel



HEAVY-DUTY CONSTRUCTION• .375" (.95cm) steel face plate on the rotor housing

• .25" (6.35cm) steel on the rest of the housing

• Frame is 2.5" x 2.5" (5cm x 5cm) 7 gauge steel tubing

• Feed table is 10 gauge steel

• Tongue is 3" x 3" (7.6cm x 7.6cm) with .25" (6.35mm) wall thickness


P215-75R15 tires with 3,000 lb (1360kg) torsion axle suspension enables the chipper to be easily towed down the highway

TOWING WEIGHT• CH8720iH – 2,225 lbs. (1,009kg)

• CH8993H – 2,350 lbs. (1,066kg)


• Height adjustable coupler. Has 3 positions in 2" (5cm) increments

TELESCOPING TONGUE• Adjustable length and height. The length may be

adjusted up to 18" (45cm)

ADJUSTABLE TONGUE JACK• Roller wheel with 850 lb. (385kg) rating



360° ROTATIONAL BED• Bed can rotate 360° for ease of feeding from any direction

• Brake for locking bed in place. With drop pin for positive transport lock

• Keeps work crews out of the street


• Safety chains




• 2 5/16" Coupler (P/N: 14519-00)

• Pintle Hitch (P/N: 14900-00)

• Low Profile Discharge Chute Kit (P/N: 74581-00)

• Knee Bar Safety Kit (P/N: 76195-00)


8" (20cm) CAPACITY TURNTABLE CHIPPERS 2 of 2

Models: CH8720iH & CH8993H


CHIPPERS9" (23cm) CAPACITY - 1 of 2

Models: CH911DH & CH922DH

ENGINESCH911DH

• Kubota engine 1.1 Liter Diesel, 69 cu in. (1.1 liter)



CH922DH

• Kubota engine 2.2 Liter Diesel 134 cu in. (2.2 liter)



FUEL CAPACITY/CONSUMPTION• 18 gal (68 liters)

• Fuel consumption on the 1.1 Liter Diesel Kubota is estimated at 1.7 gal. (7.57 liters) per hour at full load

• Fuel consumption on the 2.2 Liter Diesel Kubota is estimated at 3 gal. (14.2 liters) per hour at full load









BEARINGS• Two 1.75" (4.5cm) greasable bearings with four bolt

cast flanges





HYDRAULIC FEED SYSTEM• Steel hydraulic reservoir, 3 gal. (11.5 liters) capacity




• Self-contained system with infinite speed settings, dedi-cated neutral and full reverse, pump output 6.6 GPM (25 LPM) and 4 hp with maximum pressure and maximum flow, however this is rarely required



• 2-stage pump




• Provides an Amber code that alerts the operator every 15 hours to change chipping blades




• 90° Feed Angle

• Feed table is 38" (96.5cm) long


INTEGRATED DISCHARGE• With a 360° rotatable, 8" (20cm) diameter steel tubing



HEAVY-DUTY CONSTRUCTION• .375" (.95cm) steel face plate on the rotor

housing

• .25" (6.35mm) steel on the rest of the housing

• 4" (10cm) "C" Channel frame construction


P215-75R15 tires with 3000 lb (1360kg) torsion axle suspension enables the chipper to be easily towed down the highway

23888.625.4520

CHIPPERS9" (23cm) CAPACITY - 2 of 2

Models: CH911DH & CH922DH

TOWING WEIGHT • CH911DH – 2,480 lbs. (1,125kg)

• CH922DH – 2,700 lbs. (1,225kg)

TELESCOPING TONGUE• Pintle hitch is standard with 2" (5cm) ball coupler

available as an accessory

• Adjustable length and height. The length may be adjusted up to 18" (45cm) with four pin settings on the pintle hitch

ADJUSTABLE TONGUE JACK• Roller wheel with 850 lbs. (385kg) rating




• Safety chains




• Electric Brake Kit (P/N: 72730)

• 2" (5cm) Coupler 10,000 lbs. (P/N: 77232-00)

• 2 5/16" (5.9cm) Coupler (P/N: 14519-00)


• Fine Chip Rotor Kit (P/N: 76775-00)

• Knee Bar Safety Kit (P/N: 76195-00)

• Hour Meter Kit - Diesel (P/N: 71921)


PTO MACHINES

PTO DRIVE• 540 rpm input

• Recommend 25-45 hp (19-34kW) at the PTO





• 19" diameter

CHIPPER BLADES & SHREDDING KNIVES• Four reversible heat-treated chipper steel blades


• 36 Reversible Shredding Knives


flanges

BELT DRIVE• Two single-banded belts


• Maximum shredder capacity up to .75" (2cm)


HEAVY-DUTY CONSTRUCTION• 7 gauge steel chipper/shredder housing

• .75" (1.9cm) steel flywheel

• Discharge screen is .25" (6.35mm) steel


• Weight: 450 lbs. (204.1 kg)


PARTS & ACCESSORIES• Double-Edge Blade Kit (P/N: 72493)


• Vacuum Hose Kit (P/N: 71125) (requires P/N: 71110)

• Two-Speed Blower (P/N: 71110)

• Single-Speed Blower (P/N: 70487)

• Screen, Fine – .375" (.95cm) (P/N: 70703)

• Screen, Medium – .75" (2cm) (P/N: 70531)

• Screen, Standard – 1.5" (3.8cm) (P/N: 70332)

• Screen, Wet Debris (P/N: 70559)

5" (13cm) CAPACITY CHIPPER/SHREDDERModel: SC5540

25888.625.4520

PTO MACHINES

POWER SOURCE• 540 rpm input







• 20.6" (52.3cm) diameter

CHIPPER BLADES & SHREDDING KNIVES• Four reversible heat-treated chipper steel blades


• 36 Reversible Shredding Knives


flanges

BELT DRIVE• Double-banded belt drive

FEED CHUTES• Shredder hopper is 13" x 20" (33cm x 51cm)



INTEGRATED DISCHARGE • With a 360° rotatable, 6" (15.25cm) diameter steel

tubing with adjustable discharge


UNIQUE SCREENLESS SHREDDER• Unique product, self-feed chipper/shredder without a

screen

HEAVY-DUTY CONSTRUCTION• 7 gauge reinforced steel bed


• Weight: 720 lbs. (326kg)


PARTS & ACCESSORIES• Chipper Blade Kit (P/N: 72493)


5" (13cm) CAPACITY CHIPPER/SHREDDER/BLOWERModel: SC5540B

CHIPPER/SHREDDER/

BLOWER


PTO MACHINES



14" (35.6cm) DIAMETER ROTOR• 14" (35.6cm) diameter by 1" (2.5cm) thick rotor





CHIPPER BLADES• Two reversible heat-treated steel chipper blades



flanges





FEED CHUTE• Opening 13" x 14.5" (33cm x 36.8cm), 39" (99cm)

off the ground

• Feed throat opening is 4.5" x 5" (11.4cm x 12.7cm)

• Maximum feed size of up to 4.5" (11.4cm)

INTEGRATED DISCHARGE• Standard discharge is 4.5" x 4.5" (11.4cm x 11.4cm)

and discharges towards the ground, from a height of 14.9" (38cm)

• Optional Discharge is 4.5" x 4.5" (11.4cm x 11.4cm) discharges with adjustable deflector at a height of 55" (140cm)

HEAVY-DUTY CONSTRUCTION• 7 gauge steel throughout housing with welded

construction

3-POINT HITCH• Category 1

• Chipper weight is 361 lbs. (164kg)




• Optional Discharge Chute 4.5" x 4.5" (11.4cm x 11.4cm)(P/N: 74634-00)

4.5" (11cm) CAPACITY CANTILEVER CHIPPERModel: CH45540

27888.625.4520

PTO MACHINES






• Rotates at 1,615 rpm (CH5540)

• Rotates at 1,630 rpm (CH5540H)



CHIPPER BLADES• Four reversible heat-treated steel chipper blades



flanges.





HYDRAULIC FEED SYSTEM (CH5540H)• Single 15" (38cm) diameter top feed roller

• Maximum capacity of 3 gal. (11.36 LPM) at 2,500 psi

• Electric/Hydraulic System to control feed roller direction

• 2-stage hydraulic pump


• Feed throat opening is 5.5" x 7.5" (14cm x 19cm)

• Maximum feed size of 5" (13cm)

INTEGRATED DISCHARGE• With a 360° rotatable, 6" (15.25cm) diameter steel



HEAVY-DUTY CONSTRUCTION• .25" (6.35mm) steel throughout housing with welded con-

struction

CATEGORY 1 3-POINT HITCH• CH5540 - Weight is 600 lbs. (272kg)

• CH5540H - Weight is 980 lbs. (445kg)

MACHINE DIMENSIONS• CH5540 – LxWxH 50" x 45" x 90"

(127cm x 114cm x 229cm)

• CH5540H – LxWxH 68" x 49" x 90" (173cm x 124cm x 229cm)


PARTS & ACCESSORIES • Blade Kit (P/N: 72493)

• Auto Feed Kit - CH5540H (P/N: 73071)

5" (13cm) CAPACITYModels: CH5540 & CH5540H


PTO MACHINES


• Recommend 35hp to 60hp (26kW-45kW) at the PTO






• Easily accessible through the hinged cover, when opened, it exposes one half of the rotor for easy access to the chip-ping blades and makes for easy clean out

CHIPPER BLADES• Four reversible heat-treated steel chipper blades



flanges

BELT DRIVE• Triple-banded belt drive

ANVIL/CUTTER BAR• Four-sided adjustable anvil



46.5" (118cm) off the ground



INTEGRATED DISCHARGE• With a 360° rotatable, 8" (20cm) diameter steel tubing




• .25" (6.35mm) steel on the wrap around with welded con-struction

• Frame is 2" x 2" (5cm x 5cm), 7 gauge steel



• Weight: 886 lbs. (402kg)




8" (20cm) CAPACITYModel: CH8540

29888.625.4520

PTO MACHINES


• Recommend 35hp to 60hp (26kW-45kW) at the PTO

30" (76CM) DIAMETER ROTOR• 30" (76cm) diameter by 1.25" (3.2cm) thick rotor






CHIPPER BLADESCH9540H

• Four reversible heat-treated steel chipper blades


CHF9540H

• 16 reversible heat-treated steel chipper blades


• Blades are spaced on the rotor to provide maximum coverage and produce an extremely small chip


flanges

BELT DRIVE• Triple-banded belt drive

ANVIL/CUTTER BAR• Four-sided adjustable anvil


HYDRAULIC FEED SYSTEM• Steel hydraulic reservoir, 3 gal. (11.5 liter) capacity




• Self-contained system with infinite speed settings, dedi-cated neutral and full reverse, pump output 6.6 GPM (25 LPM) and 4Hp with maximum pressure and maximum flow, however this is rarely required



• 2-stage hydraulic pump

9" (23cm) CAPACITY 1 of 2

Models: CH9540H & CHF9540H


PTO MACHINES




• Provides an Amber code that alerts the operator every 15 hours to inspect chipping blades




• 90° feed angle


INTEGRATED DISCHARGECH9540H

• 360° rotatable, 8" (20cm) diameter steel tubing with adjustable spout cap discharges from a height of 93" (236cm)

CHF9540H

• 6" (15cm) diameter square discharge. Discharges toward the ground from a height of 34" (86cm)


• .25" (6.35mm) steel on the rest of the housing

• Frame is 2" x 2" (5cm x 5cm), 7 gauge steel


• Chipper weight is 1,300 lbs. (590kg)

MACHINE DIMENSIONSCH9540H


CHF9540H



PARTS & ACCESSORIES• Blade Kit for model CH9540H (P/N: 76293-00)

• Blade Kit for model CHF9540H (P/N: 74830-00)


• Fine Chip Rotor Kit (P/N: 76775-00)

9" (23cm) CAPACITY 2 of 2

Models: CH9540H & CHF9540H

31888.625.4520

SKID STEER CHIPPERS

SKID-STEER MOUNT• CH450H fits mini skid steer

(Minimum: 11 gpm - Maximum: 15 gpm)

• CH500H fits skid steers with standard (Minimum: 15 gpm - Maximum: 22 gpm)

• CH800H fits skid steers with high-flow hydraulics (Minimum: 25 gpm - Maximum: 38 gpm)

• CH500H and CH800H have two mounts, so chipper can be mounted with feed table facing forward or to the curbside

• Easy to attach just connect chipper to the SAE J2513 Quik-Tach, attach the hydraulic hoses, and you are ready to go

CHIPPER ROTORCH450H - Cantilever

• 14" (35.6cm) diameter by 1" (2.5cm) thick rotor• Weighs 49 lbs. (22.2kg)• Machine balanced• Rotates at 2,700 rpm at 11 gpm – 3,700 rpm at 15 gpm• 1.25" (3.2cm) diameter rotor shaft

CH500H

• 20" (51cm) diameter by 1.25" (3.2cm) thick rotor• Weighs 140 lbs. (63.5kg)• Machine balanced• Rotates at 2,700 rpm at 15 gpm – 4,000 rpm at 22 gpm• 1.5" (3.8cm) diameter rotor shaft

CH800H• 30" (76cm) diameter by 1.25" (3.2cm) thick rotor



• Rotates at 1,600 rpm at 25 gpm – 2,500 rpm at 38 gpm


CHIPPING BLADES• Reversible heat-treated chipper steel blades• CH450H has two blades

• CH500H and CH800H have four blades• CH450 & CH800H - LxWxH – 5" x 4" x .5"

(12.7cm x 10.2cm x 1.3cm)

• CH500H - LxWxH – 3.125" x 2" x .25" (7.9cm x 5cm x .6cm)

BEARINGS• CH450H - Two 1.25" (3.2cm) greasable bearings

with two bolt cast flanges

• CH500H - Two 1.5" (3.8cm) greasable bearings with two bolt cast flanges

• CH800H - Two 1.75" (4.5cm) greasable bearings with four bolt cast flanges


HYDRAULIC FEED (CH500H AND CH800H) • Four position manual valve control

(Reverse - Neutral - Forward - Reverse)

• Infinite speed settings with turn of a handle

FEED CHUTES CH450H• 4.5" x 4.5" (11.4cm x 11.4cm) chipper opening for side

limbs. Maximum feed size of 4.5" (11.4cm)

CH500H• 5.5" x 7" (14cm x 18cm) chipper opening for side

limbs. Maximum feed size of 5" (12.7cm)

CH800H• 9" x 9" (23cm x 23cm) chipper opening for side

limbs. Maximum feed size of 8" (20cm)

INTEGRATED DISCHARGE• The CH450H's standard discharge is 4.5" x 9" (11.4cm x

22.9cm) and discharges towards the ground, from a height of 10.5" (.27m)

• The CH500H and the CH800H have a 360° rotating, 6" (15cm) (CH500H) or 8" (20cm) (CH800H) diameter steel tubing with adjustable deflector cap thich allows you to put the chips where you want them the first time. These two models also discharge at a height of 93" (2.36m)

MACHINE DIMENSIONS & WEIGHTSCH450H• 41" x 28" x 40" (104cm x 71cm x 102cm)

359 lbs. (163kg)

CH500H• 73" x 53" x 93" (185cm x 135cm x 236cm)

1,145 lbs. (520kg)

CH800H• 74" x 60" x 88" (188cm x 152cm x 234cm)

1,525 lbs. (693kg)


PARTS & ACCESSORIES• Optional Discharge Chute 4.5" x 4.5" (11.4cm x 11.4cm)

(P/N: 74634-00)

CH450H• Chipper Blade Kit (P/N 76295-00)

CH500H• Chipper Blade Kit (P/N: 72493)

CH800H (Serial #804670 & up)• Chipper Blade Kit (P/N: 76293-00)

4.5" (13cm) TO 8" (20cm) CAPACITYModels: CH450H, CH500H & CH800H


LOG SPLITTERS

ENGINES• LS22 – Subaru SP 170cc

• LS27 – Subaru SP 210cc

FUEL CAPACITY• LS22 – .95 gal. (3.6 liters)

• LS27 – .95 gal. (3.6 liters)

TONNAGE/FORCE• LS22 – up to 22 tons of splitting force

• LS27 – up to 27 tons of splitting force

CYLINDER• LS22 – 4" (10cm) diameter

• LS27 – 4.5" (11cm) diameter

OPERATING POSITIONS• Horizontal and vertical

CYCLE TIMES• LS22 – 12 Seconds

• LS27 – 14 Seconds

HYDRAULICS • LS22 – 4 gal. (15 liters) system

with a 2-stage 14 gpm (53 liters) pump

• LS27 – 4.5 gal. (17 liters) system with a two-stage 14 gpm pump

MAXIMUM LOG LENGTH• 24" (61cm)

CAST IRON WEDGE• Overall LxWxH – 6.25" x 8.25" x 8"

(16cm x 21cm x 20cm)

• Splitting surface LxWxH – 5" x 5.75" x 7.75" (12.7cm x 14.6cm x 19.7cm)

MACHINE DIMENSIONS & WEIGHTS• LxWxH – 84" x 39" x 40" (213cm x 99cm x 101cm)

• LS22 – 450 lbs. (204kg)

• LS27 – 455 lbs. (206.1kg)

BEAM• Wide end plate for greater stability in the vertical

position

• Bed Height - 30" (76cm) from ground

TRANSPORT• 4.8-8 (12cm x 20cm) wheels

• Weight distributed evenly

• 2" (5cm) Ball Coupler

• Lights and fenders are available as an accessory

• Maximum Tow Speed – 45 mph (72 Km/h)


PARTS & ACCESSORIES• Log Splitter Valve Seal Kit (P/N: 77622-00)

• Log Splitter Cradle Kit (P/N: 77189-00)

• Quick Split Kit (P/N: 75896-00)

• Fenders & Tail Light Kit (P/N: 77510-00)

• Cast Wedge Kit (P/N: 77380-00)

• 4-Way Wedge Kit (P/N: 77514-00)

• Tach/Hour Meter Kit (P/N: 31605-00)

Models: LS22 & LS27

33888.625.4520

WHEELED TRIMMERS

ENGINE• Briggs & Stratton Quantum 190cc

FUEL CAPACITY• .25 gal. (.95 liter)

TRIMMER DISC PLATE DESIGN• Made of steel, not aluminum or plastic• Easy line replacement design

TRIMMER SHAFT & MOW BALL• .75" (1.9cm) steel trim head shaft • Heat-treated steel mow ball • Single belt driven cutting head• 2.25" collared anti-wrap collar design

ADJUSTABLE CUTTING HEIGHT• Trimmer disc can be reversed providing two different cut-

ting heights

TRIMMER LINE• .155 mil round line standard• .130 mil line optional• Ten 21" (52cm) pieces of round .155 mil included• .155 & .175 mil CrossFire line available

OFF-SET TRIM (WT190)• Body of trimmer can be pivoted to the left 13° or 4"

(10.2 cm) at the nose, to reach beyond the wheel base.

TILT (WT190T)• Three settings, 5°, 10° and 13°• Trim and edge along fences, barriers, foundations,

walls and other obstructions

BUILT TO LAST• 14 gauge steel frame & cutting head• Enclosed housing keeps debris out• 5/8" Solid steel axle

CUTTING SWATH• Cutting swath is 24" (61cm), while machine is only

21" (53cm) from the outer edges of tires

LARGE WHEELS• Large 15" (38.1cm) wheels with shielded ball bearings

ADJUSTABLE HANDLE BAR• Three settings for ergonomic operation

WEIGHT • WT190 - 77 lbs. (35kg) • WT190T - 77 lbs. (35kg) • WT190S - 82 lbs. (37.2kg)

SOUND LEVEL• The average dB rating at the operator is 92 dB pressure

and 99 dB power level.

SELF-PROPELLED• Model WT190S self-propelled with 3 speed transmission• Speeds for 3-speed transmission are 1 to 3 mph.


FEATURES• Comes with .155 mil line. .130 mil line optional. .75" Steel

Trim Head Shaft and 5/8" Solid Steel Axle. Enclosed under-carriage to keep debris from getting in. Three different handle bar height settings for operator convenience. Powder baked paint handle bar and bail with foam grip. Much more uniform cut than a hand held trimmer.

• Mechanical “Off Center Trim" tilts head 18° and moves body over for straight trimming. This function allows for trimming along the edge and down to the base of a sidewalk. With re-spect to wood/vinyl fences, you can go along under the fence not marking it up and with chain link fence you can get under it without being as apt to break the trimmer line.

Models: WT190, WT190T & WT190S

Optional Wrapping Method 1

Optional Wrapping Method 2

Standard Wrapping Method


WHEELED TRIMMERSModels: WT190, WT190T & WT190S

ACCESSORIES

.155" diameter Round 10 Pack

20" pre-cut length, P/N: 32030-00

.130" diameter line

Round, 10 pk.P/N: 72777

Round, 1 lb. donutP/N: 12388

Square, 10 pk.P/N: 72778

Square, 1 lb. donutP/N: 12389

.155" diameter line

Round, 10 pk.P/N: 72780




Nylon Blade KitP/N: 73060

14" Triple Blade Brush CutterFor extremely heavy/thick weeds

P/N: 32086-00

Proline HeadP/N: 74891-00

Heat-treated Mow Ball P/N: 72704-12

14" Sabre Tooth Blade Carbide tipped teeth for small trees & saplings up to 4" (10cm) in diameter

P/N: 74548-00

.155" diameter 10 Pack 20" pre-cut length, P/N: 32029-00

.175" diameter 10 pack 20" pre-cut length, P/N: 32031-00

35888.625.4520

STUMP GRINDER

ENGINE • Honda GXV 340cc

DOUBLE-BANDED BELT DRIVE SYSTEM• Double-banded belt driving the cutter head for more

positive power transfer. Belt tension idler

• Reduces belt maintenance greatly

CARBIDE TIPPED TEETH• 12 carbide tipped teeth offer maximum cutting

performance. These teeth are locked into the cutter head (8 curved, 4 straight teeth)

• The cutter head turns at 3,600 rpm with a speed at the tips 8,460 ft/min (2578 m/min)

• A screen covered opening increases visibility to the cutter head

7" (17.8cm) DIAMETER CUTTER HEAD• Large cutting diameter giving a smooth cut and can be

easily removed for quick and easy sharpening

• Cutter head at 15 degree angle

• Designed for use on stumps from 6" (15cm) above grade to a maximum of 4" (10cm) below grade

DEBRIS FLAP• Mounted to the stump grinder axle

LARGE ENCLOSED DRIVE SHAFT• Prevents chips from building up in the belts and pulleys

• Large 1.5" (3.8cm) diameter drive shaft provides superior reliability

16" (40.64cm) PNEUMATIC WHEELS• Pneumatic tires 4.80-8 rim with ball bearing hub

SINGLE WHEEL BRAKE• Allows the stump grinder to pivot and keep in position

while grinding effortlessly

ENGINE KILL SWITCH• Safety feature to shut engine off if disengaged for

added safety


WEIGHT• 195 lbs. (88kg)


PARTS• 12 Blade Cutter Replacement Kit (P/N: 76292-00)

Model: SG340

Single Wheel Brake 12 Blade Cutter Replacement KitP/N: 76292-00


WHEELED VACUUMS

ENGINES• WV160/WV160S – Honda 160cc GCV

• WV190/WV190S – Briggs & Stratton 190cc Professional Series

FAN ROTOR• 5-blade steel fan

• .25" (6.35mm) Steel welded rotor construction

ONE PIECE HOUSING• Made with .20" (.5cm) thick Linear Low Density

Polyurethane with a UV inhibitor

• Easily removable adapter with bag

• Discharge opening 6" x 6.5" (15cm x 16.27cm)

• Intake width 27" (68.58cm)

SELF-PROPELLED• Models WV160S and WV190S are 3 speed self-propelled

(1st – .71 mph (1.14 kph), 2nd – .93 mph (1.5 kph), 3rd – 1.21 mph (1.95 kph))

• Self-propelled rear wheel drive provides more traction

• Ball bearing wheels for a smoother, easier ride

HANDLEBARS• Four adjustable height settings

• Cushion Grip

BAG• Large capacity, hard bottom, quick dump bag,

5-bushel capacity

• Dust reducing

• Heavy-duty, double stitched nylon zipper with deflector flaps

• Adjustable hanger straps

ADJUSTABLE FRONT – FIVE HEIGHT SETTINGS• .25" (.64cm) above ground, ground level set at factory

• 1.25" (3.175cm)

• 2.375" (6.0325cm)

• 3.5" (8.89cm)

• 4.5" (14.43cm)

MACHINE DIMENSIONS• 61" x 27" x 46" (155cm x 69cm x 117cm)

at maximum handle height

• WV160 – 108 lbs. (49kg)

• WV190 – 113 lbs. (51kg)

• WV160S – 121 lbs. (55kg)

• WV190S – 126 lbs. (57kg)


PARTS & ACCESSORIES• Additional Debris Bag (P/N: 31339-00)

• Caster Wheels (P/N: 76967-00)

• 4" Diameter Hose Kit (P/N: 73606-00)

• Durable Nozzle Wear Plate (P/N: 73640-00)

• Vacuum Wear Liner (P/N: 76466-00)

Models: WV160, WV160S, WV190 & WV190S

37888.625.4520 37888.625.4520

DEBRIS LOADERS

ENGINES• DL8390

Honda GX 390cc with recoil start

• DL10570 Briggs & Stratton Vanguard 570cc with recoil start

FUEL CAPACITY• DL8390 - 1.6 gal. (6 liters)

• DL10570 - 2.1 gal. (7.9 liters)

FAN AND HOUSING• Wear liners made out of high strength steel

• 4-blade fan made of .375" (.9cm) steel

• Scrolled fan housing for more efficient transfer of air

• Direct drive

• One bolt access cover removal for easy fan clean out

DISCHARGE CHUTE• 360° Rotational 8" (20.3cm) discharge chute

BUILT TO LAST• Heavy-duty hose swivel boom

• Light-weight aluminum handle

• 8" (20.3cm) diameter 12' (3.6m) long flex hose (model DL8390)

• 10" (25.4cm) diameter 12' (3.6m) long flex hose (model DL10570)

CFMS• DL8390 – 2300

• DL10570– 2500

MACHINE DIMENSIONSDL8390


DL10570


WEIGHTS DL8390

• 280 lbs. (127kg)

DL10570

• 280 lbs. (127kg)


PARTS & ACCESSORIES• Wear Liner Replacement Kit (P/N: 75768-00)

• 4' (1.2 m) Flexible Horizontal Chute Extension (P/N: 74737-00)

• 16" Vertical Chute Extension (P/N: 75888-00)

• Swing Away Hitch Mount Kit (P/N: 75739-00)

• Tailgate Adapter Kit (P/N: 75753-00)

HITCH MOUNT DEBRIS LOADERSModels: DL8390, DL10570


DEBRIS LOADERS

ENGINESDL12653

• Subaru EH 653cc with electric start

DL12720

• Subaru EH 720cc with electric start

FUEL CAPACITY• 9 gal. (34.1 liters) polyethylene tank

FAN AND HOUSING• Wear liners made out of special high strength steel

• 4-blade fan made out of .375" (9.5mm) steel

• Scrolled fan housing for more efficient transfer of air

DRIVEDL12653• Direct drive

DL12720

• Double-banded belt drive with manual belt engagement

DISCHARGE CHUTE• 360° rotational 8" (20cm)

BUILT TO LAST• Heavy-duty swivel boom with hose storage

• 12" (30.5cm) diameter 12' (3.6m) long flex hose

• Lightweight aluminum handle

• One bolt access cover removal for easy fan clean out

MACHINE DIMENSIONSDL12653


DL12720


WEIGHTSDL12653

• 595 lbs. (269.9 kg)

DL12720

• 675 lbs. (306.2 kg)

CFMS• DL12653 – 3400

• DL12720 – 3400


PARTS & ACCESSORIES• Flexible Hose 12" x 12' (30.5cm x 3.7m) (P/N: 12778)

• Wear Liner Replacement Kit (P/N: 77073-00)

• 16" (40.6 cm) Vertical Chute Extension (P/N: 75888-00)

• 4' (1.2 m) Flexible Horizontal Chute Extension (P/N: 74737-00)

• Universal Road Towable Trailer Kit (P/N: 77041-00)

• 12 Volt Work Light Kit (P/N: 77105-00)

SKID MOUNT DEBRIS LOADERSModel: DL12653, DL12720

Model shown with optional trailer.

39888.625.4520

ECHO BEAR CAT GEAR

SAFETY GLASSESLightweight and impact resistant. Hard-coated optical-grade, abrasion resistant lenses. Polycarbonate lenses offer 99.9% protection from the most intense UV rays.

Tech GlassesP/N: 36773-00

Zone II GlassesP/N: 36774-00

VIBRATION-REDUCING SPORT/LANDSCAPE GLOVES

Premium, padded-leather-palm gloves help reduce

vibration. Also feature form fitting fingers and Velcro®-type wrist band for tight fit.

P/N: 31299-00 (large)

P/N: 31300-00 (xlarge)

EAR MUFFS

These light-weight ear muffs have an NRR of 29 dB(A) when used as directed and meet

CE standard 3.19.

P/N: 36775-00

CE EN352-1:2002

Highly visible vest features 5-point tear away panels for safety.

P/N: 36777-00 (large)P/N: 36778-00 (xlarge)P/N: 36779-00 (xxlarge)

ISEA 107-2004

PREMIUM SAFETY VEST

REUSABLE VINYL EARPLUGS WITH CASE

The handy carrying case can be worn on your belt when not in use. Cleanup is easy with just warm

water. CE and OSHA approved.

P/N: 31539-00

HELMET SYSTEM

Includes helmet, mesh face visor and ear protection.

P/N: 36776-00

CE EN397:1995 CLASS EG & CCE EN1663B

CE EN352-3:1997


WARRANTY COVERAGECURRENT MODELS 1 of 2

U.S. and Canada – (Purchase made after Jan. 1, 2013)

PRODUCT ECHO BEAR CAT WARRANTY

CHIPPER/SHREDDER

MODEL ENGINE CONSUMER COMMERCIAL RENTAL PARTS LABOR

SC2170 Subaru 170cc

3 years

N/A N/A

YES YES

SC3206 Briggs & Stratton 205cc N/A N/A

SC3265 Subaru 265cc

1 year 6 months

SC3305 Briggs & Stratton 305cc

SC3305E Briggs & Stratton 305cc


SC5540N/A

SC5540B

SC5720B Subaru 720cc

CHIPPERS


CH4400 Subaru 404cc

3 years 1 year 6 months YES YES

CH45540

N/A

CH5540

CH5540H

CH500H

CH800H

CH5653 Subaru 653cc

CH611DH Kubota 1.1 L

CH6730H Kohler 730cc

CH8720iH Subaru 720cc

CH8993H Briggs & Stratton 993cc

CH8540

N/ACH9540H

CHF9540H



WHEELED TRIMMERS


WT190

Briggs & Stratton 190cc 3 years 1 year 6 months YES YESWT190T

WT190S

41888.625.4520

WARRANTY COVERAGECURRENT MODELS 2 of 2

U.S. and Canada – (Purchase made after Jan. 1, 2013)


DEBRIS LOADERS


DL8390 Honda 390cc

3 years 1 year 6 months YES YESDL10570 Briggs & Stratton 570cc

DL12653 Subaru 653cc


STUMP GRINDERS


SG340 Honda 340cc 3 years 1 year 6 months YES YES

WHEELED VACUUMSMODEL ENGINE CONSUMER COMMERCIAL RENTAL PARTS LABOR

WV190Briggs & Stratton 190cc

3 years 1 year 6 months YES YESWV190S

WV160Honda 160cc

WV160S

LOG SPLITTERSMODEL ENGINE CONSUMER COMMERCIAL RENTAL PARTS LABOR

LS22 Subaru 170cc3 years 1 year 6 months YES YES

LS27 Subaru 210cc

3 YEAR WARRANTY: Valid on any ECHO Bear Cat product purchased after January 1, 2013. U.S. & Canada Only.

“Consumer” defined as: complete unit for residential or non-income producing use.“Commercial” defined as: complete unit for commercial, institutional, agricultural, horticultural or income producing use.“Rental” defined as: complete unit for rental purposes to produce income.

*Models SC2170, SC2206 & SC3206 are classified as Consumer grade products and will not qualify for warranty coverage if used for Commercial or Rental purposes.

ENGINE WARRANTY: For Engine Warranty information or service needs regarding the engine of your machine, record the serial number of the engine and refer to the Engine Owners Manual for terms and conditions of the manufacturer or see your nearest dealer.


WARRANTY COVERAGENON-CURRENT PRODUCTION 1 of 2

U.S. and Canada – (Non-current Production - Purchase made after Jan. 1, 2013)


CHIPPER/SHREDDERS



3 years

N/A N/A

YES YES

SC3240, SC3240T

Honda 240cc

1 year 6 monthsSC3270, SC3270T

Honda 270cc

SC5614 Honda 614cc

SC5670B Honda 670cc

CHIPPERS


CH45342 Briggs & Stratton 342cc


CH45390 Honda 390cc

CH45540 N/A

CH4614 Honda 614cc

CH4540 N/A

CH6614, CH6614H

Honda 614cc

CH6670H Honda 670cc


CH8670H Honda 670cc

CH123DH Kubota 3 L

WHEELED TRIMMERS


WT160THonda 160cc


WT160S

WT24

Subaru 190ccWT24T

WT24S

WT190SE Briggs & Stratton 190cc Elec. Start

DEBRIS LOADERS


DL12670 Honda 670cc3 years 1 year 6 months YES YES

DL12725 Kohler 725cc

43888.625.4520

WARRANTY COVERAGENON-CURRENT PRODUCTION 2 of 2

U.S. and Canada – (Non-current Production - Purchase made after Jan. 1, 2013)

3 YEAR WARRANTY: Valid on any ECHO Bear Cat product purchased after January 1, 2013. U.S. & Canada Only.






WV179Kawasaki 179cc 3 years 1 year 6 months YES YES

WV179S


LS21E 1.5 hp single phase electric

3 years

N/A N/A

YES YES

LS21 Subaru 190cc

1 year 6 months

LS21160, LS21160T

Honda 160cc

LS27270, LS27270T

Honda 270cc

LS33340, LS33340T

Honda 340cc


WARRANTY COVERAGE


CHIPPER/SHREDDER


SC2170 Subaru 170cc

2 years

N/A N/A

YES YES

SC3206 Briggs & Stratton 205cc N/A N/A

SC3265 Subaru 265cc

1 year 6 months


SC3305E Briggs & Stratton 305cc


SC5540N/A

SC5540B

SC5720B Subaru 720cc

CHIPPERS


CH4400 Subaru 404cc


CH45540

N/A

CH5540

CH5540H

CH500H

CH800H

CH5653 Subaru 653cc


CH6730H Kohler 730cc

CH8720iH Subaru 720cc


CH8540

N/ACH9540H

CHF9540H



WHEELED TRIMMERS


WT190

Briggs & Stratton 190cc 2 years 1 year 6 months YES YESWT190T

WT190S

CURRENT MODELS 1 of 2

All areas Outside the U.S. and Canada

45888.625.4520

WARRANTY COVERAGE


DEBRIS LOADERS


DL8390 Honda 390cc

2 years 1 year 6 months YES YESDL10570 Briggs & Stratton 570cc



STUMP GRINDERS


SG340 Honda 340cc 2 years 1 year 6 months YES YES


WV190Briggs & Stratton 190cc

2 years 1 year 6 months YES YESWV190S

WV160Honda 160cc

WV160S


LS22 Subaru 170cc2 years 1 year 6 months YES YES

LS27 Subaru 210cc

NOTE:




CURRENT MODELS 2 of 2



NON-CURRENT MODELS 1 of 2


WARRANTY COVERAGE


CHIPPER/SHREDDERS



2 years

N/A N/A

YES YES

SC3240, SC3240T

Honda 240cc

1 year 6 monthsSC3270, SC3270T

Honda 270cc

SC5614 Honda 614cc

SC5670B Honda 670cc

CHIPPERS


CH45342 Briggs & Stratton 342cc


CH45390 Honda 390cc

CH45540 N/A

CH4614 Honda 614cc

CH4540 N/A

CH6614, CH6614H

Honda 614cc

CH6670H Honda 670cc


CH8670H Honda 670cc

CH123DH Kubota 3 L

WHEELED TRIMMERS


WT160THonda 160cc


WT160S

WT24

Subaru 190ccWT24T

WT24S

WT190SE Briggs & Stratton 190cc Elec. Start

DEBRIS LOADERS


DL12670 Honda 670cc2 years 1 year 6 months YES YES

DL12725 Kohler 725cc

47888.625.4520

WARRANTY COVERAGENON-CURRENT MODELS 2 of 2




WV179Kawasaki 179cc 2 years 1 year 6 months YES YES

WV179S


LS21E 1.5 hp single phase electric

2 years

N/A N/A

YES YES

LS21 Subaru 190cc

1 year 6 months

LS21160, LS21160T

Honda 160cc

LS27270, LS27270T

Honda 270cc

LS33340, LS33340T

Honda 340cc

NOTE:





BELT REFERENCE GUIDEPart Number Description Models Area Used

12106 Belt, 3V670 Kevlar 72085, 72285, 72385 (SN =>21300), 75011, 75111 Beater Bar

12119 Belt, 2RB65 73525 Drive

12273 Belt, 3B90 Banded CH922DH (74950) Drive

12317 Belt, 4L 53 73040, 73050, 73450, 74040, 74450, 74455, 74050, 74060, 74065, 75065, 76065, WT160, WT160T, WT190, WT190T Drive

12365 Belt, 3VX530 73710, SG340 (73711) Drive

12573 Belt, 3L x 52 Kevlar 73150, 73350, 73265, 73455, 75365, WT160S, WT190S, WT190SE Drive

12660 Belt, 4L350 CH5540H (74554), 74624, 74520 Hyd Feed

16000 Belt, BX-65 70500 Drive

16043 Belt, 29” CH6730H, CH6670H (76624) & CH6993H (76635)(SN>603143), Pump

16043 Belt, 29” SC3206 (70050) (SN>105334), SC3342 (75311) (Single Belt Drive SN<C03478), SC3305 (70080), SC3270E (70085), SC3240 (78380), 70180 Drive

16081 Belt, 27” SC3206 (70050) (SN<105334) Drive

16086 Belt, BX-49 70487 Drive

16347 Belt, 2B70 Banded SC5614 (71020), 73413, 73420, 74520, 73120, 73125, 73725, 71014, DL12670 (75124), DL12720 Drive

16500 Belt, VGates 6958 71110, 71125 Drive

16559 Belt, 3B83 Banded CH8720iH, CH6614 (71620), CH6614H (72620), CH911DH (72928), CH8670H (76824), CH8993H (76835), 71825, 72825, 74824, Drive

16636 Belt, BX-43 CH9540H (72854), CHF9540H (76854) Hyd Feed

16660 Belt, BX-38 CH911DH (72928) & CH922DH (74950)(VIN<5VJAA00118W000989), CH6614 (72620), 72825, 74824, 72942, Hyd Feed

16691 Belt, 3VX500 71755 Drive

16787 Belt, 3B85 Banded 72942 Drive

16799 Belt, 2R3VX475 EL COG 71785 Drive

16911 Belt, 3V560 72085, 72285, 72385, 75011, 75111 Drive

16912 Belt, 3V600 72085, 72285, 72385 (SN<21300) Beater Bar

17055 Belt, BX-56 [Qty 2] SC5540B (73454), CH5540H (74554), CH5540, SC5540 (70554), 70520 Drive

17558 Belt, 4L-38 70251, 70252 Drive

17996 Belts, 29” (Matched set) SC3265, SC3240 (70380), SC3240T (70580), 70385, SC3342 (Dual Belt Drive SN=>C03478) Dual Belt Drive

13426-00 Belt, 2RBP56 SC5540B (73554) Drive

13884-00 Belt, SP BEARVAC (3L32) WV190S (75360) WV179S (77360), and WV160S (75350) Drive

13973-00 Belt, 2RB63 Banded SC5670B (75524) Drive

14261-00 Belt, 3RB48 Banded CH6730H, CH6993H (76635), CH611DH (76628), CH6670H (76624), 74628, 74624, Drive

14770-00 Belt, 2RB61 CH4400, CH45342 (77412), CH45390 (77413) Drive

14804-00 Belt, 5-5V750, Non Cog CH123DH (7812086) Drive

18093-00 Belt, 2RB47 [Qty 2] CH45540 (77454) Drive

18277-00 BX44 Belt CH8720iH, CH8670H (76824), CH8993H (76835) Hydraulic

18531-00 BX30 Belt CH911DH, CH922DH (VIN>5VJAA00178W001015) Hydraulic

18633-00 BX33 Belt CH611DH (76628) Hydraulic

31460-00 Belt, 2BRP67 CH5653 Drive

31498-00 Belt, 2RB40 SC5720B Drive

31995-00 Belt, 5L500 Wrapped Aramid WT24, WT24S, WT24T Head

32124-00 Belt, 4L180 WT24S Transmission

32252-00 Belt, 3RB64 CH8540 (71854), CH9540H (72854), CHF9540H (76854) Drive

49888.625.4520

ROTOR & CHIPPER/SHREDDER KITS

COMPLETE ROTOR REPLACEMENT ASSEMBLIES

Part Number Description Models

70062Replacement Rotor Assembly, 8 HP machines (SN 25659 and below) (Shredder kit not included)

SC3265, SC3305 (70080), SC3305E (70085), SC3240 (70380), SC3240T (70580), SC3270, SC3270T, SC3342 (75311), 70385, 70180

70277Replacement Rotor Assembly, 5 HP machines (SN 25659 and below) (Shredder kit not included)

SC3206 (70050)

70366Replacement Rotor Assembly, 5” Chipper/Shredders (SN 26377 and below) (Shredder kit not included)

SC5540 (70554), SC5540B (71020), 71014, 70500

73371-00 Replacement Rotor Assembly, 5” Chipper/Shredders SC5670B (75524), SC5540B (73554), 73525

74209-00Rotor Replacement Assembly, 3” Chipper/Shredders (Wide body models)

SC3265, SC3305 (70080), SC3305E (70085), SC3240 (70380), SC3240T (70580), SC3270, SC3270T, SC3342 (75311), 70385, 70180

75399-00 Rotor Replacement Assembly SC2206


77612-00 Rotor Replacement Assembly SC5720B


SHREDDER KNIVES REPLACEMENT KITS

All Kits contain knives, spacers, shafts, hardware and installation instructions

Part Number Description Models

70316 Kit, Shredder Knives 70530, 70515, 70525

70972 Kit, Shredder KnivesSC5540 (70554), SC5614 (71020), SC5670B (75524), SC5540B (73554), 73525, 71014, 70520

70973 Kit, Shredder Knives (Wide body 3” SC models)SC3265, SC3305 (70080), SC3305E (70085), SC3240 (70380), SC3240T (70580), SC3270, SC3270T, SC3342 (75311), 70385, 70180

71381 Kit, Shredder Knives (Narrow body 3” SC models) SC3206 (70050) - Serial # C03159 and below

75502-00 Kit, Shredder Knives SC2206

77589-00 Kit, Shredder Knives (Narrow body 3” SC models) SC3206 - Serial # C03478 and above

77613-00 Kit, Shredder Knives SC5720B

77616-00 Kit, Shredder KnivesSC2170

77618-00 Kit, Optional Additional Shredder Knives


BLADE KITS

KITS CONTAIN ALL NECESSARY BLADES AND HARDWARE 1 of 2

MODELS SN RANGE VIN RANGE KIT P/N DESCRIPTION

3" CHIPPER/SHREDDERS

70515, 70525, 70530 0 - Current 70317 Small Chipper Blade Kit

SC2170, SC2206, SC3206 (70050), SC3265, SC3305

(70080), SC3305E (70085), SC3270 (70380), SC3270T (70580), SC3342 (75311),

SC3240, 70385, 70030, 72085, 72285, 70180

0 - 25658* 70205 Single Edge Small Blade Kit

25659 - Current 5VJAA00137W000009 -Current 70738 Tool Steel Blade Kit

4" & 5" CHIPPERS

CH4400 0 - Current 76295-00 Chipper Blade Kit

CH5653, CH5540, CH4540 (73454), CH5540H (74554),

CH500H (74500), 734130 - Current

72493 Chipper Blade Kit

CH4614 (73420) 0 - 705078 5VJAA00197W000009 - Current

4.5" CHIPPERS

CH45342 (77412), CH45540 (77454), CH450H, CH45390

(77413)

0 - 902474 0 - 5VJAA00109W001849 74744-00 77412/13 Blade Kit

902475 - Current 5VJAA00109W001850 - Current 76295-00 4-1/2 Chipper Blade Kit

5" CHIPPER/SHREDDERS

SC5540 (70554), SC5614 (71020), SC5540B (73554), SC5670B

(75524), SC5720B, 70500, 70520, 71014, 74520, 73525

0 - 26376* 70453 Single EdgeBlade Kit

26377 - Current 5VJAA00137W000071 - Current 72493 Chipper Blade Kit

6" CHIPPERS

CH6730H, CH6670H (76624), CH611DH (76628), CH6993H

(76635), 74624, 74628

0 - 704809 0 - 5VJAA00159W001743 74220-00 6 Inch Blade Kit

5VJAA00159W001744 - Current 76293-00 Chipper Blade Kit

CH6614 (71620), CH6614H (72620) 0 - 705118 5VJAA00157W000010 - Current 71426 8 Inch Chipper

Blade Kit

51888.625.4520

BLADE KITS

KITS CONTAIN ALL NECESSARY BLADES AND HARDWARE 2 of 2

MODELS SN RANGE VIN RANGE KIT P/N DESCRIPTION

8" CHIPPERS

CH8720iH, CH8993H (76835), CH8670H (76824)

0 - 704960 0 - 5VJAA00119W001755 71426 8 Inch Chipper Blade Kit

5VJAA00119W001756 - Current76293-00 Chipper Blade Kit

74824, CH800H (74800)

904473 - Current

0 - 804669 71426 8 Inch Chipper Blade Kit

8" & 9" PTO CHIPPERS

CH8540 (71854), CH9540H (72854)

0 - 901387 71426 8 Inch Chipper Blade Kit

901388 - Current 76293-00 Chipper Blade Kit

CHF9540H (76854) 502304 - Current 74830-00 Blade Kit

9" CHIPPERS

CH911DH (72928), CH922DH (74950)

0 - 704696 0 - 5VJAA00109W001785 71426 8 Inch Chipper Blade Kit

5VJAA00109W001786 - Current 76293-00 Chipper Blade Kit

12" CHIPPERS

CH123DH (7812086) 500423 - Current 5VJAA00137W000023 - Current 73900-00 12" Blade Kit

STUMPGRINDERS

SG340 (73711), 71755, 71785, 73710 0 - 805549 71445 4 Blade Stump

Cutter Kit

SG340 810639 - Current

76292-00 12 Blade Cutter Replacement Kit73711 with 12-blade retrograde

fit kit, PN: 76256-00 0 - Current

SG340

0 - Current 76903-00

12 Blade Cutter Retro Fit Kit

(To change from 4 blade to 12 blade system)

0 - Current 76906-00

12 Blade Cutter Upgrade Kit

(To change from 6 bolt to 12 bolt system)


ACCESSORIES

Shredder Knives Kit P/N: 70972. Models: SC5540 & SC5540B.

Blades and Knives Kits

Blade Kit, P/N: 70738 Models: SC2170, SC3206, SC3265, SC3305

SC3305E & SC3342

Blade Kit, P/N: 76295-00 Models: CH4400, CH45540 & CH450H

Blade Kit, P/N: 72493 Models: SC5720B, SC5540, SC5540B, CH5653, CH5540H & CH5540

Blade Kit, P/N: 76293-00 Models: CH611DH, CH6730H, CH8720iH, CH8993H,

CH911DH, CH922DH, CH8540, CH9540H & CHF9540

Shredder Knives Kit P/N: 77616-00. Model: SC2170.

Additional Knives Kit, P/N: 77618-00

53888.625.4520

ACCESSORIES

Fine Screen

Medium Screen

Coarse Screen Standard

Wet Debris Screen

Shredder Knives Kit P/N: 77613-00. Model: SC5720B

Debris Bag, P/N: 17854 Models: Any models that discharge to the ground

Shredder Knives Kit P/N: 77589-00. Model: SC3206

Shredder Knives Kit, P/N: 70973 Models: SC3265, SC3305, SC3305E & SC3342

Blades and Knives Kits 3" SC Screens

SC2170 Screens

See model page for specific corresponding part numbers.

See model page for specific corresponding part numbers.

.75" FineWet

Debris1.13"

Standard


ACCESSORIES

Blower Kit with 2-Blade Radial Fan P/N: 70251, Models: SC3265, SC3305, SC3305E & SC3342

All Weather Cover, P/N: 70093 Models: All 3" Chipper/Shredders

Leaf Tamper, P/N: 70089 Models: All 3" Chipper/Shredders

Two Wheel Tow Kit, P/N: 77000-00Models: All 3" Chipper/Shredders

Road Towable Chipper/Shredder Trailer, P/N: 77353-00 Models: All 3" Chipper/Shredders

Pintle Hitch, P/N: 14900-00 Models: CH611DH, CH6730H, CH8720iH & CH8993H

Supplemental Adaptor Kit (For Models Serial C03477 & below)Wide Body ModelsP/N: 77700-00SC3206P/N: 77701-00

55888.625.4520

ACCESSORIES

4.5" x 4.5" (11.4cm x 11.4cm) Discharge Chute P/N: 74634-00. Models: CH4400, CH450H & CH45540

Adjustable Feed Speed Kit, P/N: 76820-00 Models: CH611DH & CH6730H

Low Profile Discharge, P/N: 74581-00 Models: CH8540, CH8720iH, CH8993H, CH911DH,

CH922DH, CH9540H & CHF9540H

Hour/Tach Kit - Gas, P/N: 31605-00 Models: All gasoline engine powered machines

Hour Meter Kit - Diesel, P/N: 71921 Models: CH911DH & CH922DH

12 Tooth Cutter Replacement Kit P/N: 76292-00. Model SG340


ACCESSORIES

Log Cradle P/N: 77189-00. Models: LS22 & LS27

Quick Split Kit P/N: 75896-00. Models: LS22 & LS27

Fenders & Tail Lights Kit P/N: 77510-00. Models: LS22 & LS27

4-Way Wedge P/N: 77514-00. Models: LS22 & LS27

57888.625.4520

ACCESSORIES

.155" diameter Round 10 Pack

20" pre-cut length, P/N: 32030-00

.130" diameter line

Round, 10 pk.P/N: 72777




.155" diameter line

Round, 10 pk.P/N: 72780




Nylon Blade KitP/N: 73060

14" Triple Blade Brush CutterP/N: 32086-00

Proline HeadP/N: 74891-00

Heat-treated Mow Ball P/N: 72704-12

14" Sabre Tooth Blade Saplings up to 4" (10cm) in diameter

P/N: 74548-00

.155" diameter 10 Pack 20" pre-cut length, P/N: 32029-00

.175" diameter 10 pack 20" pre-cut length, P/N: 32031-00


ACCESSORIES

Vacuum Hose Kit P/N: 73606-00. Models: WV190 & WV190S

Caster Wheel KitP/N: 76967-00. Models: All Wheeled Vacuums

Nozzle Wear PlateP/N: 73640-00. Models: All Wheeled Vacuums

Vacuum LinerP/N: 76466-00. Models: All Wheeled Vacuums

Debris Bag P/N: 31339-00. Models: WV190 & WV190S

Swing Away Hitch Mount KitP/N: 75739-00. Models: DL8390 & DL10570

Tailgate Adapter KitP/N: 75753-00. Models: DL8390 & DL10570

59888.625.4520

ACCESSORIES

Wear Liner Replacement Kit P/N: 75768-00. Models: DL8390 & DL10570

4' (1.2m) Flexible Chute Extension P/N: 74737-00. Models: All Debris Loaders

Debris Loader Light Kit P/N: 77105-00. Models: DL12653 & DL12720

16" (41cm) Vertical Chute Extension, P/N: 75888-00 Models DL8390, DL10570, DL12653 & DL12720

Wear Liner Replacement Kit P/N: 77073-00. Models: DL12653 & DL12720

To view a complete list of ECHO Bear Cat parts and

accessory options, please visit our website

www.bearcatproducts.com and click on

Options and Accessories under the Products tab.

http://www.bearcatproducts.com

www.bearcatproducts.com

P.O. Box 849 West Fargo, ND 58078-0849

Phone: 1.701.282.5520 Fax: 1.701.282.9522 Toll Free: 1.888.625.4520

Email: [email protected] Web: www.bearcatproducts.com

ECHO Bear Cat • 237 12th St. NW, West Fargo, ND 58078Specifications, descriptions and illustrative material in this literature is as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories and may not include all standard equipment

©2014 ECHO Bear Cat, a subsidiary of ECHO Incorporated All Rights Reserved.

#32968-00 - Updated 10/2013

Date post:	06-Mar-2016
Category:	Documents
Upload:	rick-cleghorn
View:	329 times
Download:	21 times

2014 ECHO Bearcat saleshandbook

Documents