Technical Bulletin № 57 -2016.07 Тhis technical bulletin presents: new ways for application of profile from system E 85 on existing load bearing structure; new profile allowing incorporation of openable parts; new continuous gaskets; possibility for development of façade only from third level transoms through application of continuous gaskets with different depth of the channels, allowing drainage at different levels. Table of contents: Page 1 – Table with profiles Page 2 – Profiles 1:1 Page 3-4 – Application of profile E 85350 on transom and mullion by using continuous gaskets ЕТ 130801 (vertical direction) and ЕТ 130802 (horizontal direction) – cover cap type Page 5-6 - Application of profile E 85350 on transom and mullion by using continuous gaskets ЕТ 130801 (vertical direction) and ЕТ 130802 (horizontal direction) – structural glazing type Page 7-8 – Development of façade only from third level transoms through application of continuous gaskets ЕТ 130801 (vertical direction) and ЕТ 130802 (horizontal direction) – cover cap type Page 9-12 – New profile for application E 85121 for mullion and transom structural glazing type. The depth of the profile allows incorporation of openable parts. This profile is tailor made and designed according to the special requirements for project in Turkey. Page 13-14 – Machining Page 15 – Accessories and gaskets
Transcript
Technical Bulletin № 57 -2016.07
Тhis technical bulletin presents:
� new ways for application of profile from system E 85 on existing load bearing structure;
� new profile allowing incorporation of openable parts;
� new continuous gaskets;
� possibility for development of façade only from third level transoms through application
of continuous gaskets with different depth of the channels, allowing drainage at different
levels.
Table of contents:
� Page 1 – Table with profiles
� Page 2 – Profiles 1:1
� Page 3-4 – Application of profile E 85350 on transom and mullion by using continuous
gaskets
ЕТ 130801 (vertical direction) and ЕТ 130802 (horizontal direction) – cover cap type
� Page 5-6 - Application of profile E 85350 on transom and mullion by using continuous gaskets
ЕТ 130801 (vertical direction) and ЕТ 130802 (horizontal direction) – structural glazing type
� Page 7-8 – Development of façade only from third level transoms through application of
continuous
gaskets ЕТ 130801 (vertical direction) and ЕТ 130802 (horizontal direction) – cover cap type
� Page 9-12 – New profile for application E 85121 for mullion and transom structural glazing
type. The depth of the profile
allows incorporation of openable parts. This profile is tailor made and designed according to
the special requirements for project in Turkey.
� Page 13-14 – Machining
� Page 15 – Accessories and gaskets
5016
X
Y
6Ix= 0,41Wx= 0,35ex= 2,50ix= 0,43
Iy= 3,78Wy= 1,51еy= 1,18iy= 1,30
E853503rd leveltransom
6,01 m605 g/m204 mm62 mm
cm4
cm3
cmcm
cm4
cm3
cmcm
E851213rd leveltransom
70
60
50
X
Y
6,01 m2165 g/m503 mm66 mm
Ix= 30.80Wx= 8,50ex= 2,50ix= 1,96
Iy= 15,80Wy= 6.32еy= 3,62iy= 1,40
cm4
cm3
cmcm
cm4
cm3
cmcm
26.4
7.5
E19641cover cap
6,6 m130 g/m81 mm26 mm
E85 technical catalogue
curtain wall systemE85
lengthweightext.perimetervis.perimeter
profilecodedescription static values
L85-
01
119
911
2010
20
50
10 6
16
E85350
E85121
1010
1010
2010
20
50
10 24.5
70
27 8.5
11
26.4
7.5
E19641
4.1E85 technical catalogue
curtain wall system
E85
backer rod
steel construction By Others
membrane- al. butil
EPDM gasket for mullion ET130801.00
al. profile E85350
mullion 3rd level with cover cap for application
scale 3/4
E85C
P5.7
membrane
Note:Horizontal EPDM GASKET FOR TRANSOM pass above vertical EPDM GASKET FOR MULLION.
Note:1. Horizontal EPDM GASKET FOR TRANSOM pass above vertical EPDM GASKET FOR MULLION.2. This technical solution could be used for vertical facade.
100
60
steel construction By Others
EPDM gasket for transom ET130802.00
transom E85350
membrane
glazing support ET071203.00
50
16
30
9
self drilling screw DIN7504 ST4.2x22-M-Z
(Bimetal, Ruspert drilling screw A2with a case- hardened drilling tip,
hardened)
Glass pane
Silicone
Backer rod
Tapping screwDIN ISO 7049 ST5.5x22-C-H
Fixing part
E85
E85 technical catalogue
curtain wall system
319
20
E85C
P5.10
mullion E85354transom E85354
DIN 7981 4.8x19-C-H
T-joint for transom ET071134.00
Flat sealing 95x2
EPDM gasket for mullion ET130801.00
backer rod
95155
Note:1. Horizontal EPDM GASKET FOR TRANSOM pass above vertical EPDM GASKET FOR MULLION.2. This technical solution could be used for vertical facade.
scale 3/4
transom 3rd level as mullion with cover cap
50
tapping screwDIN ISO 7049 ST5.5x50*-C-H
pressure plate E85700gasket ET130500.00
cover cap E85712
E85
E85 technical catalogue
curtain wall system
scale 3/4
mullion E85354
transom E85354
50
E85C
P5.9
backer rod
631 917
EPDM gasket for transom ET130802.00
glazing support ET071203.00
DIN 7981 ST4.8x19-C-Htapping screw
DIN 7981 4.8x19-C-H
T-joint for transom ET071134.00
Note:1. Horizontal EPDM GASKET FOR TRANSOM pass above vertical EPDM GASKET FOR MULLION.2. This technical solution could be used for vertical facade.
mullion 3rd level with cover cap
tapping screwDIN ISO 7049 ST5.5x50*-C-H
pressure plate E85700
cover cap E85711
gasket ET130500.00
E85
E85 technical catalogue
curtain wall system
transom for application
286
166
620
6
Steelconstructions-ByOthers
sash E85250
gasketET130176.00
gasket ET130180.00
frame E85410
100.4
E85121
E19641
MicrocelularGasket
Tapping screw 5,5*32
Backer rod
Str.Silicon
EPDM gasket
Screw Joint
E85S
G6.2
steel console for mullion
scale 3/4
E85
E85 technical catalogue
curtain wall system
E85S
G6.3
sash E85250
operating rod E2308
gasket ET130461.00
striker GI255602.00
striker GI255603.00
gasket ET130176.00
frame E85410
gasket ET130180.00structural seal 6 mm
norton tape 6x6.4 mm
gasket ET130707.00
glass support E85614
gasket ET130463.00
PVC shim
gasket ET130463.00
Tapping screw 5,5*32
Backer rod
Str.Silicone
Glazing clip
6 20 6
6 16 6
E19641
E85121
Steelconstructions-ByOthers
supplementaryanotized profile E70650
steel console for transom
scale 3/4
E85
E85 technical catalogue
curtain wall system
Nut M10
Washer DIN127AM10
E85S
G6.56 20 6
6 20 6
Steelconstructions-ByOthers
glazingblock(PVC;PE shim)
Str.Silicone
glass pane
gasket ET130463.00
E19641
E85121
Screw M10*35
Washer DIN125 M10
60
stell shim for GU
scale 3/4
Note:* Steel shims are two per every GU and are welded to main steel structure
E85
E85 technical catalogue
curtain wall system
E85121E8
5SG6
.7
6 20 6
6 20 6
Steelconstructions-ByOthers
glazingblock(PVC;PE shim)
Str.Silicone
glass pane
gasket ET130463.00
E19641
Backer rod
Tapping screw5,5*32
glazing clip new
Washer 68x2 EPDM
50
60
Washer 68x2AISI 316
scale 3/4
Note:* Additional washers in vertical and/or horizontal direction for mechanical support.
E85
E85 technical catalogue
curtain wall system
Sequence for mounting of E85-aplication
Steel construction - by others!1 EPDM - tape2
Note:Complete static calculations are done on the basis of a working project and details from the building company, approved by the architects of the structure.
mounting E85350 with self drilling screw DIN 7504 ST4.2x22-M-Z(Bimetal, Ruspert drilling screw A2 with a case - hardened drilling tip, hardened)
3
15.5
16
5024.5 105 21 3
20
4.5
19
E85350
Next mounting hole - by specific static calculation!
15.5E85350
3
4.5
19
Next
mou
nting
hole -
by
spec
ific
sta
tic c
alcu
latio
n!
Silicone
Steel shim for GU weldedto main steel structure
M85-
1
E85
E85 technical catalogue
curtain wall system
Sequence for mounting of E85-aplication
EPDM gasket for mullion ET130801.00
Apply glue - Elastofix beforeapply EPDM gasket for transomET130802.00
EPDM gasket for transom ET130802.00
Make sure to fill EPDM gasket for transom ET130802.00with silicone or UNIONZEMENT in zone of steel glazing shim
IMPORTANT! Make sure to fill EPDM gasket for transomET130802.00 with UNIONZEMENT in zone of contact withEPDM gasket for mullion ET130801.00 - (20mm)
Cutting of EPDM gasket formullion ET130801.00
Cutting of EPDM gasket fortransom ET130802.00
16
6.5
50
5.3
Note:Before add silicon or UNIONZEMENT, clean treatment surface with cleaner!Gaskets ET130801.00 and ET130802.00 must be glue with UNIONZEMENT in every 1m spot!
