Page 1
- www.snacademycenter.com – Page 1 of 33
List of International Organization for
Standardization standards
ISO 1 – ISO 99 ISO 1:2002 Geometrical Product Specifications (GPS) – Standard reference
temperature for geometrical product specification and verification
ISO 2:1973 Textiles – Designation of the direction of twist in yarns and related
products
ISO 3:1973 Preferred numbers – Series of preferred numbers
ISO 4:1997 Information and documentation – Rules for the abbreviation of title words
and titles of publications
ISO 5 Photography and graphic technology – Density measurements
ISO 6:1993 Photography – Black-and-white pictorial still camera negative
film/process systems – Determination of ISO speed
ISO 7 Pipe threads where pressure-tight joints are made on the threads
ISO 8:1977 Documentation – Presentation of periodicals
ISO 9:1995 Information and documentation – Transliteration of Cyrillic characters
into Latin characters – Slavic and non-Slavic languages
ISO 11:1987 Aircraft – Ground pressure testing connections for pressure cabins
ISO 12:1987 Aerospace – Pipelines – Identification
ISO 14:1982 Straight-sided splines for cylindrical shafts with internal centering –
Dimensions, tolerances and verification
ISO 15:2011 Radial bearings—Boundary dimensions, general plan
ISO 16:1975 Acoustics – Standard tuning frequency (Standard musical pitch)
ISO 17:1973 Guide to the use of preferred numbers and of series of preferred numbers
ISO 18:1981 Documentation – Contents list of periodicals
ISO 21:1985 Shipbuilding – Inland navigation – Cable-lifters for stud-link anchor
chains
ISO 22:1991 Belt drives – Flat transmission belts and corresponding pulleys –
Dimensions and tolerances
ISO 23:1993 Cinematography—Camera usage of 35 mm motion-picture film—
Specifications
ISO 25:1994 Cinematography—Camera usage of 16 mm motion-picture film—
Specifications
ISO 26:1993 Cinematography—Projector usage of 16 mm motion-picture films for
direct front projection—Specifications
ISO 28:1976 Cinematography—Camera usage of 8 mm Type R motion-picture
film—Specifications
ISO 29:1980 Cinematography—Projector usage of 8 mm Type R silent motion-
picture film for direct front projection—Specifications [Withdrawn without
replacement]
ISO 31 Quantities and units [withdrawn: replaced with ISO/IEC 80000]
ISO 32:1977 Gas cylinders for medical use—Marking for identification of content
ISO 34
o ISO 34-1:2010 Rubber, vulcanized or thermoplastic—Determination of tear
strength—Part 1: Trouser, angle and crescent test pieces
Page 2
- www.snacademycenter.com – Page 2 of 33
o ISO 34-2:2011 Rubber, vulcanized or thermoplastic—Determination of tear
strength—Part 2: Small (Delft) test pieces
ISO 35:2004 Natural rubber latex concentrate—Determination of mechanical stability
ISO 36:2011 Rubber, vulcanized or thermoplastic—Determination of adhesion to
textile fabrics
ISO 37:2011 Rubber, vulcanized or thermoplastic — Determination of tensile stress-
strain properties
ISO 41:1980 Shipbuilding—Inland vessels—Covers for deck openings for pumps
[withdrawn without replacement]
ISO 43:1976 Aircraft—Jacking pads
ISO 44:1975 Aerospace—Lever-operated, two-position, ON/OFF switches—
Directions of operation
ISO 45:1990 Aircraft—Pressure refuelling connections
ISO 46:1973 Aircraft—Fuel nozzle grounding plugs and sockets
ISO 48:2010 Rubber, vulcanized or thermoplastic—Determination of hardness
(hardness between 10 IRHD and 100 IRHD)
ISO 49:1994 Malleable cast iron fittings threaded to ISO 7-1
ISO 50:1977 Metal pipes—Steel sockets screwed according to ISO 7 [Withdrawn
without replacement]
ISO 53:1998 Cylindrical gears for general and heavy engineering—Standard basic
rack tooth profile
ISO 54:1996 Cylindrical gears for general engineering and for heavy engineering—
Modules
ISO 55:1977 Seedlac—Specification [Withdrawn without replacement]
ISO 57:1975 Bleached lac—Specification [Withdrawn without replacement]
ISO 60:1977 Plastics—Determination of apparent density of material that can be
poured from a specified funnel
ISO 61:1976 Plastics—Determination of apparent density of moulding material that
cannot be poured from a specified funnel
ISO 62:2008 Plastics—Determination of water absorption
ISO 63:1975 Flat transmission belts—Lengths [Withdrawn: Replaced with ISO 22]
ISO 65:1981 Carbon steel tubes suitable for screwing in accordance with ISO 7-1
ISO 67:1981 Muscovite mica blocks, thins and films—Grading by size [Withdrawn
without replacement]
ISO 68 ISO general-purpose screw threads – Basic profile
o ISO 68-1:1998 Metric screw threads
o ISO 68-2:1998 Inch screw threads
ISO 69:1998 Cinematography—16 mm motion-picture and magnetic film—Cutting
and perforating dimensions
ISO 70:1981 Cinematography—35 mm negative photographic sound record on
35 mm motion-picture film—Position and maximum width dimensions
ISO 71:1977 Cinematography—16 mm negative photographic sound record on
16 mm, 35/16 mm and 35/32 mm motion-picture film—Positions and dimensions
ISO 74:1976 Cinematography—Image area produced by camera aperture and
maximum projectable image area on 8 mm Type R motion-picture film—Positions
and dimensions
ISO 75 Plastics—Determination of temperature of deflection under load
o ISO 75-1:2013 Plastics—Determination of temperature of deflection under
load—Part 1: General test method
Page 3
- www.snacademycenter.com – Page 3 of 33
o ISO 75-2:2013 Plastics—Determination of temperature of deflection under
load—Part 2: Plastics and ebonite
o ISO 75-3:2004 Plastics—Determination of temperature of deflection under
load—Part 3: High-strength thermosetting laminates and long-fibre-reinforced
plastics
ISO 76:2006 Rolling bearings—Static load ratings
ISO 78 Chemistry — Layouts for standards
o ISO 78-2:1999 Chemistry—Layouts for standards—Part 2: Methods of
chemical analysis
o ISO 78-3:1983 Chemistry—Layouts for standards—Part 3: Standard for
molecular absorption spectrometry
o ISO 78-4:1983 Layouts for standards—Part 4: Standard for atomic absorption
spectrometric analysis
ISO 82:1974 Steel—Tensile testing [Withdrawn: replaced with ISO 6892-1]
ISO 83:1976 Steel—Charpy impact test (U-notch) [Withdrawn: replaced with ISO
148-1]
ISO 86:1974 Steel—Tensile testing of sheet and strip less than 3 mm and not less than
0,5 mm thick [Withdrawn: replaced with ISO 6892-1]
ISO 89:1974 Steel—Tensile testing of wire [Withdrawn: replaced with ISO 6892-1]
ISO 90 Light gauge metal containers—Definitions and determination of dimensions
and capacities
o ISO 90-1:1997 Light gauge metal containers—Definitions and determination
of dimensions and capacities—Part 1: Open-top cans
o ISO 90-2:1997 Light gauge metal containers—Definitions and determination
of dimensions and capacities—Part 2: General use containers
o ISO 90-3:2000 Light gauge metal containers—Definitions and determination
of dimensions and capacities—Part 3: Aerosol cans
ISO 91 Petroleum measurement tables
o ISO 91-1:1992 Petroleum measurement tables—Part 1: Tables based on
reference temperatures of 15 degrees C and 60 degrees F
o ISO 91-2:1991 Petroleum measurement tables—Part 2: Tables based on a
reference temperature of 20 degrees C
ISO 92:1976 Textile machinery and accessories—Spinning machinery—Definition of
side (left or right)
ISO 93 Textile machinery and accessories—Cylindrical sliver cans
o ISO 93-1:2006 Textile machinery and accessories—Cylindrical sliver cans—
Part 1: Main dimensions
o ISO 93-2:2006 Textile machinery and accessories—Cylindrical sliver cans—
Part 2: Spring bottoms
ISO 94:1982 Textile machinery and accessories—Spindle gauges for ring-spinning
and ring-doubling frames
ISO 96 Textile machinery and accessories—Rings and travellers for ring spinning and
ring twisting frames
o ISO 96-1:2009 Textile machinery and accessories—Rings and travellers for
ring spinning and ring twisting frames—Part 1: Flange rings T and SF and
their travellers
o ISO 96-2:2009 Textile machinery and accessories—Rings and travellers for
ring spinning and ring twisting frames—Part 2: HZ- and J-rings and their
travellers
Page 4
- www.snacademycenter.com – Page 4 of 33
ISO 97:1975 Textile machinery and accessories—Rings for spinning, doubling and
twisting for ear-shaped travellers
ISO 98:2001 Textile machinery and accessories—Spinning preparatory and spinning
machinery—Main dimensions of coverings for top rollers
ISO 100 – ISO 199 ISO 100:1984 Pulleys for flat transmission belts—Crowns [Withdrawn: replaced with
ISO 22]
ISO 102:1990 Aircraft—Gravity filling orifices
ISO 104:2002 Rolling bearings—Thrust bearings—Boundary dimensions, general
plan
ISO 105 Textiles — Tests for colour fastness
o ISO 105-A01:2010 Part A01: General principles of testing
o ISO 105-A02:1993 Part A02: Grey scale for assessing change in colour
o ISO 105-A03:1993 Part A03: Grey scale for assessing staining
o ISO 105-A04:1989 Part A04: Method for the instrumental assessment of the
degree of staining of adjacent fabrics
o ISO 105-A05:1996 Part A05: Instrumental assessment of change in colour for
determination of grey scale rating
o ISO 105-A06:1995 Part A06: Instrumental determination of 1/1 standard
depth of colour
o ISO 105-A08:2001 Part A08: Vocabulary used in colour measurement
o ISO 105-A11:2012 Part A11: Determination of colour fastness grades by
digital imaging techniques
o ISO 105-B01:1994 Part B01: Colour fastness to light: Daylight
o ISO 105-B02:2013 Part B02: Colour fastness to artificial light: Xenon arc
fading lamp test
o ISO 105-B03:1994 Part B03: Colour fastness to weathering: Outdoor exposure
o ISO 105-B04:1994 Part B04: Colour fastness to artificial weathering: Xenon
arc fading lamp test
o ISO 105-B05:1993 Part B05: Detection and assessment of photochromism
o ISO 105-B06:1998 Part B06: Colour fastness and ageing to artificial light at
high temperatures: Xenon arc fading lamp test
o ISO 105-B07:2009 Part B07: Colour fastness to light of textiles wetted with
artificial perspiration
o ISO 105-B08:1995 Part B08: Quality control of blue wool reference materials
1 to 7
o ISO 105-B10:2011 Part B10: Artificial weathering—Exposure to filtered
xenon-arc radiation
o ISO 105-C06:2010 Part C06: Colour fastness to domestic and commercial
laundering
o ISO 105-C07:1999 Part C07: Colour fastness to wet scrubbing of pigment
printed textiles
o ISO 105-C08:2010 Part C08: Colour fastness to domestic and commercial
laundering using a non-phosphate reference detergent incorporating a low-
temperature bleach activator
o ISO 105-C09:2001 Part C09: Colour fastness to domestic and commercial
laundering—Oxidative bleach response using a non-phosphate reference
detergent incorporating a low temperature bleach activator
o ISO 105-C10:2006 Part C10: Colour fastness to washing with soap or soap
and soda
Page 5
- www.snacademycenter.com – Page 5 of 33
o ISO 105-C12:2004 Part C12: Colour fastness to industrial laundering
o ISO 105-D01:2010 Part D01: Colour fastness to drycleaning using
perchloroethylene solvent
o ISO 105-D02:1993 Part D02: Colour fastness to rubbing: Organic solvents
o ISO 105-E01:2013 Part E01: Colour fastness to water
o ISO 105-E02:2013 Part E02: Colour fastness to sea water
o ISO 105-E03:2010 Part E03: Colour fastness to chlorinated water (swimming-
pool water)
o ISO 105-E04:2013 Part E04: Colour fastness to perspiration
o ISO 105-E05:2010 Part E05: Colour fastness to spotting: Acid
o ISO 105-E06:2006 Part E06: Colour fastness to spotting: Alkali
o ISO 105-E07:2010 Part E07: Colour fastness to spotting: Water
o ISO 105-E08:1994 Part E08: Colour fastness to hot water
o ISO 105-E09:2010 Part E09: Colour fastness to potting
o ISO 105-E10:1994 Part E10: Colour fastness to decatizing
o ISO 105-E11:1994 Part E11: Colour fastness to steaming
o ISO 105-E12:2010 Part E12: Colour fastness to milling: Alkaline milling
o ISO 105-E13:1994 Part E13: Colour fastness to acid-felting: Severe
o ISO 105-E14:1994 Part E14: Colour fastness to acid-felting: Mild
o ISO 105-E16:2006 Part E16: Colour fastness to water spotting on upholstery
fabrics
o ISO 105-F01:2001 Part F01: Specification for wool adjacent fabric
o ISO 105-F02:2009 Part F02: Specification for cotton and viscose adjacent
fabrics
o ISO 105-F03:2001 Part F03: Specification for polyamide adjacent fabric
o ISO 105-F04:2001 Part F04: Specification for polyester adjacent fabric
o ISO 105-F05:2001 Part F05: Specification for acrylic adjacent fabric
o ISO 105-F06:2000 Part F06: Specification for silk adjacent fabric
o ISO 105-F07:2001 Part F07: Specification for secondary acetate adjacent
fabric
o ISO 105-F09:2009 Part F09: Specification for cotton rubbing cloth
o ISO 105-F10:1989 Part F10: Specification for adjacent fabric: Multifibre
o ISO 105-G01:1993 Part G01: Colour fastness to nitrogen oxides
o ISO 105-G02:1993 Part G02: Colour fastness to burnt-gas fumes
o ISO 105-G03:1993 Part G03: Colour fastness to ozone in the atmosphere
o ISO 105-G04:1989 Part G04: Colour fastness to oxides of nitrogen in the
atmosphere at high humidities
o ISO 105-J01:1997 Part J01: General principles for measurement of surface
colour
o ISO 105-J02:1997 Part J02: Instrumental assessment of relative whiteness
o ISO 105-J03:2009 Part J03: Calculation of colour differences
o ISO 105-J05:2007 Part J05: Method for the instrumental assessment of the
colour inconstancy of a specimen with change in illuminant (CMCCON02)
o ISO 105-N01:1993 Part N01: Colour fastness to bleaching: Hypochlorite
o ISO 105-N02:1993 Part N02: Colour fastness to bleaching: Peroxide
o ISO 105-N03:1993 Part N03: Colour fastness to bleaching: Sodium chlorite
(mild)
o ISO 105-N04:1993 Part N04: Colour fastness to bleaching: Sodium chlorite
(severe)
o ISO 105-N05:1993 Part N05: Colour fastness to stoving
Page 6
- www.snacademycenter.com – Page 6 of 33
o ISO 105-P01:1993 Part P01: Colour fastness to dry heat (excluding pressing)
o ISO 105-P02:2002 Part P02: Colour fastness to pleating: Steam pleating
o ISO 105-S01:1993 Part S01: Colour fastness to vulcanization: Hot air
o ISO 105-S02:1993 Part S02: Colour fastness to vulcanization: Sulfur
monochloride
o ISO 105-S03:1993 Part S03: Colour fastness to vulcanization: Open steam
o ISO 105-X01:1993 Part X01: Colour fastness to carbonizing: Aluminium
chloride
o ISO 105-X02:1993 Part X02: Colour fastness to carbonizing: Sulfuric acid
o ISO 105-X04:1994 Part X04: Colour fastness to mercerizing
o ISO 105-X05:1994 Part X05: Colour fastness to organic solvents
o ISO 105-X06:1994 Part X06: Colour fastness to soda boiling
o ISO 105-X07:1994 Part X07: Colour fastness to cross-dyeing: Wool
o ISO 105-X08:1994 Part X08: Colour fastness to degumming
o ISO 105-X09:1993 Part X09: Colour fastness to formaldehyde
o ISO 105-X10:1993 Part X10: Assessment of migration of textile colours into
polyvinyl chloride coatings
o ISO 105-X11:1994 Part X11: Colour fastness to hot pressing
o ISO 105-X12:2001 Part X12: Colour fastness to rubbing
o ISO 105-X13:1994 Part X13: Colour fastness of wool dyes to processes using
chemical means for creasing, pleating and setting
o ISO 105-X14:1994 Part X14: Colour fastness to acid chlorination of wool:
Sodium dichloroisocyanurate
o ISO 105-X16:2001 Part X16: Colour fastness to rubbing—Small areas
o ISO 105-X18:2007 Part X18: Assessment of the potential to phenolic
yellowing of materials
o ISO 105-Z01:1993 Part Z01: Colour fastness to metals in the dye-bath:
Chromium salts
o ISO 105-Z02:1993 Part Z02: Colour fastness to metals in the dye-bath: Iron
and copper
o ISO 105-Z03:1996 Part Z03: Intercompatibility of basic dyes for acrylic fibres
o ISO 105-Z04:1995 Part Z04: Dispersibility of disperse dyes
o ISO 105-Z05:1996 Part Z05: Determination of the dusting behaviour of dyes
o ISO 105-Z06:1998 Part Z06: Evaluation of dye and pigment migration
o ISO 105-Z07:1995 Part Z07: Determination of application solubility and
solution stability of water-soluble dyes
o ISO 105-Z08:1995 Part Z08: Determination of solubility and solution stability
of reactive dyes in the presence of electrolytes
o ISO 105-Z09:1995 Part Z09: Determination of cold water solubility of water-
soluble dyes
o ISO 105-Z10:1997 Part Z10: Determination of relative colour strength of dyes
in solution
o ISO 105-Z11:1998 Part Z11: Evaluation of speckiness of colorant dispersions
ISO 108:1976 Textile machinery and accessories—Weaving looms—Definition of
left and right sides
ISO 109:1982 Textile machinery—Working widths of weaving machines
ISO 110:1978 Textile machinery and accessories—Cones for yarn winding (cross
wound) -- Half angle of the cone 9 degrees 15' [Withdrawn without replacement]
Page 7
- www.snacademycenter.com – Page 7 of 33
ISO 111:1978 Textile machinery and accessories—Cones for yarn winding (cross
wound) -- Half angle of the cone 4 degrees 20' [Withdrawn: Replaced with ISO 8489-
3]
ISO 112:1983 Textile machinery and accessories—Cones for yarn winding (cross
wound) -- Half angle of the cone 3 degrees 30' [Withdrawn: Replaced with ISO 8489-
2]
ISO 113:2010 Rolling bearings—Plummer block housings—Boundary dimensions
ISO 114:1980 99.8 Unalloyed magnesium ingots—Chemical composition
[Withdrawn: Replaced by ISO 8287]
ISO 115:2003 Unalloyed aluminium ingots for remelting—Classification and
composition
ISO 119:1977 Plastics—Phenol-formaldehyde mouldings—Determination of free
phenols—Iodometric method
ISO 120:1977 Plastics—Phenol-formaldehyde mouldings—Determination of free
ammonia and ammonium compounds—Colorimetric comparison method
ISO 121:1980 Magnesium-aluminium-zinc alloy ingots and alloy castings—Chemical
composition and mechanical properties of sand cast reference test bars [Withdrawn:
replaced by ISO 16220]
ISO 123:2001 Rubber latex—Sampling
ISO 124:2011 Latex, rubber—Determination of total solids content
ISO 125:2011 Natural rubber latex concentrate—Determination of alkalinity
ISO 126:2005 Natural rubber latex concentrate—Determination of dry rubber content
ISO 127:2012 Rubber, natural latex concentrate—Determination of KOH number
ISO 128 Technical drawings—General principles of presentation
ISO 129
o ISO 129-1:2004 Technical drawings—Indication of dimensions and
tolerances—Part 1: General principles
o ISO 129-4:2013 Technical product documentation (TPD) -- Indication of
dimensions and tolerances—Part 4: Dimensioning of shipbuilding drawings
ISO 131:1979 Acoustics—Expression of physical and subjective magnitudes of sound
or noise in air [Withdrawn without replacement]
ISO 132:2011 Rubber, vulcanized or thermoplastic—Determination of flex cracking
and crack growth (De Mattia)
ISO 133:1983 Rubber, vulcanized—Determination of crack growth (De Mattia)
[Withdrawn: Replaced with ISO 132]
ISO 136:1972 Steel—Simple torsion testing of wire [Withdrawn replaced by ISO
7800]
ISO 137:1975 Wool—Determination of fibre diameter—Projection microscope
method
ISO 139:2005 Textiles—Standard atmospheres for conditioning and testing
ISO 140 Acoustics—Measurement of sound insulation in buildings and of building
elements
o ISO 140-2:1991 Part 2: Determination, verification and application of
precision data
o ISO 140-4:1998 Part 4: Field measurements of airborne sound insulation
between rooms
o ISO 140-5:1998 Part 5: Field measurements of airborne sound insulation of
façade elements and façades
o ISO 140-7:1998 Part 7: Field measurements of impact sound insulation of
floors
Page 8
- www.snacademycenter.com – Page 8 of 33
o ISO 140-14:2004 Part 14: Guidelines for special situations in the field
o ISO 140-18:2006 Part 18: Laboratory measurement of sound generated by
rainfall on building elements
ISO 141:1976 Textile machinery and accessories—Pirn winders and cross winders—
Definition of left and right sides
ISO 142:1976 Textile machinery and accessories—Weaving preparatory machines—
Definition of left and right sides
ISO 143:1977 Textile machinery and accessories—Weft pirns for automatic looms
[Withdrawn without replacement]
ISO 144:1973 Steel—Reverse bend testing of wire [Withdrawn: replaced with ISO
7801]
ISO 146:1984 Metallic materials—Hardness test—Verification of Vickers hardness
testing machines HV 0,2 to HV 100 [Withdrawn replaced with ISO 6507-2]
o ISO 146-2:1993 Metallic materials—Verification of Vickers hardness testing
machines—Part 2: Less than HV 0,2 [Withdrawn replaced with ISO 6507-2]
ISO 148 Metallic materials—Charpy pendulum impact test
o ISO 148-1:2009 Part 1: Test method
o ISO 148-2:2008 Part 2: Verification of testing machines
o ISO 148-3:2008 Part 3: Preparation and characterization of Charpy V-notch
test pieces for indirect verification of pendulum impact machines
ISO 150:2006 Raw, refined and boiled linseed oil for paints and varnishes—
Specifications and methods of test
ISO 155:1998 Belt drives—Pulleys—Limiting values for adjustment of centres
ISO 156:1982 Metallic materials—Hardness test—Verification of Brinell hardness
testing machines [Withdrawn replaced by ISO 6506-2]
ISO 157:1996 Coal—Determination of forms of sulfur
ISO 160:1980 Asbestos-cement pressure pipes and joints [Withdrawn without
replacement]
ISO 161 Thermoplastics pipes for the conveyance of fluids—Nominal outside
diameters and nominal pressures
o ISO 161-1:1996 Part 1: Metric series
o ISO 161-2:1996 Part 2: Inch-based series
ISO 162:1985 Cinematography—Head gaps and sound records for three-, four-, or
six-track magnetic sound records on 35 mm and single-track on 17,5 mm motion-
picture film containing no picture—Positions and width dimensions
ISO 171:1980 Plastics—Determination of bulk factor of moulding materials
ISO 172:1978 Plastics—Phenol-formaldehyde mouldings—Detection of free
ammonia
ISO 174:1974 Plastics—Homopolymer and copolymer resins of vinyl chloride—
Determination of viscosity number in dilute solution [Withdrawn replaced by ISO
1628-2]
ISO 200 – ISO 999 ISO 216:2007 Writing paper and certain classes of printed matter – Trimmed sizes –
A and B series, and indication of machine direction
ISO 226:2003 Acoustics – Normal equal-loudness-level contours
ISO 228 Pipe threads where pressure-tight joints are not made on the threads
ISO 233 Information and documentation – Transliteration of Arabic characters into
Latin characters[Note 3]
ISO 259 Information and documentation – Transliteration of Hebrew characters into
Latin characters[Note 3]
Page 9
- www.snacademycenter.com – Page 9 of 33
ISO 261 ISO general purpose metric screw threads – General plan
ISO 262 ISO general purpose metric screw threads – Selected sizes for screws, bolts
and nuts
ISO 286-1 Geometrical product specifications (GPS) – ISO code system for
tolerances on linear sizes – Part 1: Basis of tolerances, deviations and fits
ISO 286-2 Geometrical product specifications (GPS) – ISO code system for
tolerances on linear sizes – Part 2: Tables of standard tolerance classes and limit
deviations for holes and shafts
ISO 361 Basic ionizing radiation symbol
ISO 500 Agricultural tractors – Rear-mounted power take-off types 1, 2 and 3
ISO 518:2006 Photography – Camera accessory shoes, with and without electrical
contacts, for photoflash lamps and electronic photoflash units – Specification
ISO 519:1992 Photography – Hand-held cameras – Flash-connector dimensions
ISO 536:2012 Paper and board – Determination of grammage
ISO 639 Codes for the representation of names of languages
o ISO 639-1 Alpha-2 code
o ISO 639-2 Alpha-3 code
o ISO 639-3 Alpha-3 code for comprehensive coverage of languages
o ISO 639-4 General principles of coding of the representation of names of
languages and related entities, and application guidelines
o ISO 639-5 Alpha-3 code for language families and groups
o ISO 639-6 Alpha-4 code for comprehensive coverage of language variants
ISO/IEC 646 Information technology – ISO 7-bit coded character set for information
interchange
ISO 657 Hot-rolled steel sections
ISO 668 Series 1 freight containers – Classification, dimensions and ratings
ISO 690 Information and documentation – Guidelines for bibliographic references
and citations to information resources
ISO 704 Terminology work – Principles and methods
ISO 732 Photography – 120-size and 220-size films – Dimensions
ISO 764 Horology – Magnetic resistant watches
ISO 760:1978 Determination of water - Karl Fischer method (General method)
ISO 787 General methods of test for pigments and extenders
o ISO 787-9:1981 Determination of pH value of an aqueous suspension
ISO 838 Paper – Holes for general filing purposes – Specifications
ISO 843:1997 Information and documentation – Conversion of Greek characters into
Latin characters
ISO 860 Terminology work – Harmonization of concepts and terms
ISO 898 Mechanical properties of fasteners made of carbon steel and alloy steel[Note 3]
ISO 928 Spices and condiments - Determination of total ash
ISO 936 Meat and meat products - Determination of total ash
ISO 965 ISO general purpose metric screw threads – Tolerances
ISO 999 Information and documentation – Guidelines for the content, organization,
and presentation of indexes
ISO 1000 – ISO 4999 ISO 1000 SI units and recommendations for the use of their multiples and of certain
other units [withdrawn 2009-11-17]
ISO 1004 Information processing – Magnetic ink character recognition – Print
specifications
ISO 1007 Photography – 135-size film and magazine – Specifications
Page 10
- www.snacademycenter.com – Page 10 of 33
ISO 1034:1973 Aircraft - Ground air-conditioning connections
ISO 1101 Geometrical product specifications (GPS) – Geometrical tolerancing –
Tolerances of form, orientation, location and run-out
ISO 1182 Reaction to fire tests for products—Non-combustibility test
ISO 1217 Displacement compressors—Acceptance tests
ISO 1222 Photography – Tripod connections
ISO 1268 Fibre-reinforced plastics – Methods of producing test plates
ISO 1402 Rubber and plastics hoses and hose assemblies - Hydrostatic testing
ISO/IEC 1539 Information technology – Programming languages – Fortran
ISO 1629 Rubber and latices – Nomenclature
ISO 1663 Rigid cellular plastics – Determination of water vapour transmission
properties
ISO 1745 Information processing – Basic mode control procedures for data
communication systems
ISO 1750 Pesticides and other agrochemicals – Common names
ISO 1928 Solid mineral fuels – Determination of gross calorific value by the bomb
calorimetric method and calculation of net calorific value
ISO/IEC 2022 Information technology – Character code structure and extension
techniques
ISO 2108 Information and documentation – International standard book number
(ISBN)
ISO 2145 Documentation – Numbering of divisions and subdivisions in written
documents
ISO 2162 Technical product documentation – Springs
o ISO 2162-1 Simplified representation
o ISO 2162-2 Presentation of data for cylindrical helical compression springs
ISO 2171 Cereals, pulses and by-products – Determination of ash yield by
incineration
ISO 2240:2003 Photography – Colour reversal camera films – Determination of ISO
speed
ISO 2848:1984 Building construction - Modular coordination - Principles and rules
ISO 2533 Standard Atmosphere
ISO 2692 Geometrical product specifications (GPS) – Geometrical tolerancing –
Maximum material requirement (MMR), least material requirement (LMR) and
reciprocity requirement (RPR)
ISO 2709 Information and documentation – Format for information exchange
ISO 2768 General tolerances
o ISO 2768-1 Tolerances for linear and angular dimensions without individual
tolerance indications
o ISO 2768-2 Geometrical tolerances for features without individual tolerance
indications
ISO 2852 Stainless steel clamp pipe couplings for the food industry
ISO 3002 Basic quantities in cutting and grinding
ISO 3082 Iron ores – Sampling and sample preparation procedures
ISO 3098 Technical product documentation – Lettering
ISO 3103 Tea – Preparation of liquor for use in sensory tests
ISO 3166 Codes for the representation of names of countries and their subdivisions
o ISO 3166-1 Country codes
o ISO 3166-2 Country subdivision code
o ISO 3166-3 Code for formerly used names of countries
Page 11
- www.snacademycenter.com – Page 11 of 33
ISO 3297 Information and documentation – International standard serial number
(ISSN)
ISO 3394 Dimensions of rigid rectangular packages – Transport packages
ISO 3506 Mechanical properties of corrosion-resistant stainless steel fasteners
ISO 3534 Statistics – Vocabulary and symbols
o ISO 3534-1 General statistical terms and terms used in probability
o ISO 3534-2 Applied statistics
o ISO 3534-3 Design of experiments
o ISO 3534-4 Survey sampling
ISO 3536 Road vehicles – Safety glazing materials – Vocabulary
ISO 3537 Road vehicles – Safety glazing materials – Mechanical tests
ISO 3538 Road vehicles – Safety glazing materials – Test methods for optical
properties
ISO 3591 - Sensory analysis – Apparatus – Wine-tasting glass
ISO 3593 Starch — Determination of ash
ISO 3601 Fluid power systems – O-rings
o ISO 3601-1 Inside diameters, cross-sections, tolerances and designation codes
o ISO 3601-2 Housing dimensions for general applications
o ISO 3601-3 Quality acceptance criteria
o ISO 3601-4 Anti-extrusion rings (back-up rings)
o ISO 3601-5 Suitability of elastomeric materials for industrial applications
ISO 3602 Documentation – Romanization of Japanese (kana script)
ISO 3632 Spices – Saffron (Crocus sativus L.)[Note 3]
ISO 3635:1981 Size designation of clothes – Definitions and body measurement
procedure
ISO 3676 Packaging – Unit load sizes – Dimensions
ISO 3690 Welding and allied processes — Determination of hydrogen content in arc
weld metal
ISO 3864 Graphical symbols – Safety colours and safety signs
ISO 3901 Information and documentation – International Standard Recording Code
(ISRC)
ISO 3977 Gas turbines – Procurement
ISO 4074 Natural latex rubber condoms – Requirements and test methods
ISO 4157 Construction drawings – Designation systems
ISO 4165 Road vehicles — Electrical connections — Double-pole connection
ISO 4179 Ductile iron pipes and fittings for pressure and non-pressure pipelines –
Cement mortar lining
ISO 4217 Codes for the representation of currencies and funds
ISO 4314 Surface active agents — Determination of free alkalinity or free acidity —
Titrimetric method
ISO 4578 Adhesives — Determination of peel resistance of high-strength adhesive
bonds — Floating-roller method
ISO 4582 Plastics — Determination of changes in colour and variations in properties
after exposure to daylight under glass, natural weathering or laboratory light sources
ISO 4587 Adhesives — Determination of tensile lap-shear strength of rigid-to-rigid
bonded assemblies
ISO 4628 Paints and varnishes – Evaluation of degradation of coatings – Designation
of quantity and size of defects, and of intensity of uniform changes in appearance
o ISO 4628-1 General introduction and designation system
o ISO 4628-2 Assessment of degree of blistering
Page 12
- www.snacademycenter.com – Page 12 of 33
o ISO 4628-3 Assessment of degree of rusting
o ISO 4628-4 Assessment of degree of cracking
o ISO 4628-5 Assessment of degree of flaking
o ISO 4628-6 Assessment of degree of chalking by tape method
o ISO 4628-7 Assessment of degree of chalking by velvet method
o ISO 4628-8 Assessment of degree of delamination and corrosion around a
scribe
o ISO 4628-10 Assessment of degree of filiform corrosion
ISO/IEC 4873:1991 Information technology – ISO 8-bit code for information
interchange – Structure and rules for implementation
ISO 4892 Plastics – Methods of exposure to laboratory light sources
ISO 5000 – ISO 8999 ISO 5127 Information and documentation – Vocabulary
ISO 5167 Measurement of fluid flow by means of pressure differential devices
inserted in circular cross-section conduits running full
o ISO 5167-1 General principles and requirements
o ISO 5167-2 Orifice plates
o ISO 5167-3 Nozzles and Venturi nozzles
o ISO 5167-4 Venturi tubes
ISO/IEC 5218 Information technology – Codes for the representation of human sexes
ISO 5455 Technical drawings – Scales
ISO 5457 Technical product documentation – Sizes and layout of drawing sheets
ISO 5458 Geometrical Product Specifications (GPS) – Geometrical tolerancing –
Positional tolerancing
ISO 5459 Geometrical product specifications (GPS) – Geometrical tolerancing –
Datums and datum systems
ISO 5660 Reaction-to-fire tests – Heat release, smoke production and mass loss rate
o ISO 5660-1 Heat release rate (cone calorimeter method)
o ISO 5660-2 Smoke production rate (dynamic measurement)
o ISO/TS 5660-3 Guidance on measurement
ISO 5725 Accuracy (trueness and precision) of measurement methods and results
ISO 5775 Bicycle tires and rims
ISO 5776 Graphic technology - Symbols for text correction
ISO 5800:2001 Photography – Colour negative films for still photography –
Determination of ISO speed
ISO 5893 Rubber and plastics test equipment – Tensile, flexural and compression
types (constant rate of traverse) – Specification
ISO 5964 Documentation – Guidelines for the establishment and development of
multilingual thesauri
ISO 5971:1981 Size designation of clothes – Pantyhose
ISO 5993 Sodium hydroxide for industrial use—Determination of mercury content—
Flameless atomic absorption spectrometric method
ISO 6107-4:1993 Water quality—Vocabulary
ISO 6166 Securities and related financial instruments – International securities
identification numbering system (ISIN)
ISO 6194 Rotary-shaft lip-type seals incorporating elastomeric sealing elements
o ISO 6194-5 Identification of visual imperfections
ISO 6336 Calculation of load capacity of spur and helical gears
ISO 6344 Coated abrasives – Grain size analysis
ISO 6346 Freight containers – Coding, identification and marking
Page 13
- www.snacademycenter.com – Page 13 of 33
ISO 6357 Documentation – Spine titles on books and other publications
ISO/IEC 6429 Information technology – Control functions for coded character sets
ISO 6438 Documentation – African coded character set for bibliographic information
interchange
ISO/IEC 6523 Information technology – Structure for the identification of
organizations and organization parts
ISO 6579 Microbiology of food and animal feeding stuffs – Horizontal method for the
detection of Salmonella spp.
ISO 6594 Cast iron drainage pipes and fittings – Spigot series
ISO 6709 Standard representation of geographic point location by coordinates
ISO 6780 Flat pallets for intercontinental materials handling — Principal dimensions
and tolerances
ISO 6892 Metallic materials – Tensile testing
o ISO 6892-1 Method of test at room temperature
o ISO 6892-2 Method of test at elevated temperature
o ISO 6892-3 Method of test at low temperature
o ISO 6892-4 Method of test in liquid helium
ISO 6946 Building components and building elements – Thermal resistance and
thermal transmittance – Calculation method
ISO 7001 Graphical symbols – Public information symbols
ISO 7002 Agricultural food products – Layout for a standard method of sampling
from a lot
ISO 7098 Information and documentation – Romanization of Chinese
ISO 7200 Technical product documentation – Data fields in title blocks and document
headers
ISO 7240 Fire detection and alarm systems
ISO 7372 Trade data interchange
ISO/IEC 7498 Information technology -- Open Systems Interconnection — Basic
Reference Model[Note 3]
o ISO/IEC 7498-1 Information technology—Open Systems Interconnection—
Basic Reference Model: The Basic Model
o ISO 7498-2 Information processing systems—Open Systems
Interconnection—Basic Reference Model—Part 2: Security Architecture
o ISO/IEC 7498-3 Information technology—Open Systems Interconnection—
Basic Reference Model: Naming and addressing
ISO/IEC 7501 Identification cards – Machine readable travel documents
o ISO/IEC 7501-1:2008 Machine readable passport
o ISO/IEC 7501-2:1997 Machine readable visa
o ISO/IEC 7501-3:2005 Machine readable official travel documents
ISO 7736 Road vehicles – Car radio for front installation – Installation space
including connections
ISO/IEC 7810 Identification cards – Physical characteristics
ISO/IEC 7811 Identification cards – Recording technique
ISO/IEC 7812 Identification cards – Identification of issuers
ISO/IEC 7813 Information technology – Identification cards – Financial transaction
cards
ISO/IEC 7816 Identification cards – Integrated circuit cards[Note 3]
ISO/IEC 7942 Information technology – Computer graphics and image processing –
Graphical Kernel System (GKS)
ISO 8000 Data quality
Page 14
- www.snacademycenter.com – Page 14 of 33
ISO 8015:2011 Geometrical product specifications (GPS) – Fundamentals –
Concepts, principles and rules
ISO 8090 Cycles – Terminology
ISO 8180 Ductile iron pipelines – Polyethylene sleeving for site application
ISO 8373 Manipulating industrial robots – Vocabulary
ISO 8501 Preparation of steel substrates before application of paints and related
products – Visual assessment of surface cleanliness
ISO 8559:1989 Garment construction and anthropometric surveys – Body dimensions
ISO 8573 Compressed air
o ISO 8573-1 Contaminants and purity classes
o ISO 8573-2 Test methods for oil aerosol content
o ISO 8573-3 Test methods for measurement of humidity
o ISO 8573-4 Test methods for solid particle content
o ISO 8573-5 Test methods for oil vapour and organic solvent content
o ISO 8573-6 Test methods for gaseous contaminant content
o ISO 8573-7 Test method for viable microbiological contaminant content
o ISO 8573-8 Test methods for solid particle content by mass concentration
o ISO 8573-9 Test methods for liquid water content
ISO 8583 Financial transaction card originated messages – Interchange message
specifications
o ISO 8583-1 Messages, data elements and code values
o ISO 8583-2 Application and registration procedures for Institution
Identification Codes (IIC)
o ISO 8583-3 Maintenance procedures for messages, data elements and code
values
ISO 8601 Data elements and interchange formats – Information interchange –
Representation of dates and times
ISO/IEC 8613 Information technology – Open Document Architecture (ODA) and
interchange format
ISO/IEC 8632 Information technology – Computer graphics – Metafile for the storage
and transfer of picture description information
o ISO/IEC 8632-1 Functional specification
o ISO/IEC 8632-2 Character encoding
o ISO/IEC 8632-3 Binary encoding [withdrawn 2001-06-21]
o ISO/IEC 8632-4 Clear text encoding
ISO 8651 Information technology – Computer graphics – Graphical Kernel System
(GKS) language bindings[Note 3]
ISO/IEC 8652 Information technology – Programming languages – Ada
ISO 8653:1986 Jewellery – Ring-sizes – Definition, measurement and designation
ISO 8691 Petroleum products – Low levels of vanadium in liquid fuels –
Determination by flameless atomic absorption spectrometry after ashing
ISO 8805 Information processing systems – Computer graphics – Graphical Kernel
System for Three Dimensions (GKS-3D) functional description
ISO/IEEC 8806 Information technology – Computer graphics – Graphical Kernel
System for Three Dimensions (GKS-3D) language bindings
o ISO/IEEC 8806-4 C
ISO 8807 Information processing systems – Open Systems Interconnection – LOTOS
– A formal description technique based on the temporal ordering of observational
behaviour
ISO/IEC 8824 Information technology – Abstract Syntax Notation One (ASN.1)
Page 15
- www.snacademycenter.com – Page 15 of 33
ISO/IEC 8825 Information technology – ASN.1 encoding rules
ISO/IEC 8859 Information technology – 8-bit single-byte coded graphic character sets
o ISO/IEC 8859-1 Latin alphabet No. 1
o ISO/IEC 8859-2 Latin alphabet No. 2
o ISO/IEC 8859-3 Latin alphabet No. 3
o ISO/IEC 8859-4 Latin alphabet No. 4
o ISO/IEC 8859-5 Latin/Cyrillic alphabet
o ISO/IEC 8859-6 Latin/Arabic alphabet
o ISO/IEC 8859-7 Latin/Greek alphabet
o ISO/IEC 8859-8 Latin/Hebrew alphabet
o ISO/IEC 8859-9 Latin alphabet No. 5
o ISO/IEC 8859-10 Latin alphabet No. 6
o ISO/IEC 8859-11 Latin/Thai alphabet
o ISO/IEC 8859-13 Latin alphabet No. 7
o ISO/IEC 8859-14 Latin alphabet No. 8 (Celtic)
o ISO/IEC 8859-15 Latin alphabet No. 9
o ISO/IEC 8859-16 Latin alphabet No. 10
ISO 8879 Information processing – Text and office systems – Standard Generalized
Markup Language (SGML)
ISO 9000 – ISO 9999 ISO 9000 Quality management systems – Fundamentals and vocabulary
ISO 9001 Quality management systems – Requirements
ISO 9004 Managing for the sustained success of an organization – A quality
management approach
ISO 9022 Optics and optical instruments -- Environmental test methods
o ISO 9022-1:2016 Definitions, extent of testing
o ISO 9022-2:2015 Cold, heat and humidity
o ISO 9022-3:2015 Mechanical stress
o ISO 9022-4:2014 Salt mist
o ISO 9022-5:1994 Combined cold, low air pressure [Withdrawn: replaced by
ISO 9022-23:2016]
o ISO 9022-6:2015 Dust
o ISO 9022-23:2016 Low pressure combined with cold, ambient temperature
and dry or damp heat
ISO 9050 Glass in building – Determination of light transmittance, solar direct
transmittance, total solar energy transmittance, ultraviolet transmittance and related
glazing factors
ISO 9069 Information processing – SGML support facilities – SGML Document
Interchange Format (SDIF)
ISO/IEC 9075 Information technology – Database languages – SQL
ISO/IEC 9126 Software engineering – Product quality
ISO 9141 Road vehicles – Diagnostic systems[Note 3]
o ISO 9141-2 CARB requirements for interchange of digital information
o ISO 9141-3 Verification of the communication between vehicle and OBD II
scan tool
ISO 9241 Ergonomics of human-system interaction
ISO/IEC 9293 Information technology – Volume and file structure of disk cartridges
for information interchange
ISO 9362 Banking – Banking telecommunication messages – Business identifier code
(BIC)
Page 16
- www.snacademycenter.com – Page 16 of 33
ISO 9407 Shoe sizes – Mondopoint system of sizing and marking
ISO/IEC 9541 Information technology – Font information interchange
o ISO/IEC 9541-1:1991 Architecture
o ISO/IEC 9541-2:1991 Interchange Format
o ISO/IEC 9541-3:1994 Glyph shape representation
o ISO/IEC 9541-4:2009 Harmonization to Open Font Format
ISO 9564 Financial services – Personal Identification Number (PIN) management and
security
ISO/IEC 9579 Information technology – Remote database access for SQL with
security enhancement
ISO/IEC 9592 Information technology – Computer graphics and image processing –
Programmer's Hierarchical Interactive Graphics System (PHIGS)
ISO/IEC 9593 Information technology – Computer graphics – Programmer's
Hierarchical Interactive Graphics System (PHIGS) language bindings[Note 3]
ISO/IEC 9594 Information technology – Open Systems Interconnection – The
Directory
ISO/IEC 9636 Information technology - Computer graphics - Interfacing techniques
for dialogues with graphical devices (CGI) - Functional specification
o ISO/IEC 9636-1 Overview, profiles, and conformance
o ISO/IEC 9636-2 Control
o ISO/IEC 9636-3 Output
o ISO/IEC 9636-4 Segments
o ISO/IEC 9636-5 Input and echoing
o ISO/IEC 9636-6 Raster
ISO/IEC 9646 Information technology -- Open Systems Interconnection --
Conformance testing methodology and framework
o ISO/IEC 9646-1 Information technology—Open Systems Interconnection—
Conformance testing methodology and framework—Part 1: General concepts
o ISO/IEC 9646-2 Information technology—Open Systems Interconnection—
Conformance testing methodology and framework—Part 2: Abstract Test
Suite specification
o ISO/IEC 9646-3 Information technology—Open Systems Interconnection—
Conformance testing methodology and framework—Part 3: The Tree and
Tabular Combined Notation (TTCN)
o ISO/IEC 9646-4 Information technology—Open Systems Interconnection—
Conformance testing methodology and framework—Part 4: Test realization
o ISO/IEC 9646-5 Information technology—Open Systems Interconnection—
Conformance testing methodology and framework—Part 5: Requirements on
test laboratories and clients for the conformance assessment process
o ISO/IEC 9646-6 Information technology—Open Systems Interconnection—
Conformance testing methodology and framework—Part 6: Protocol profile
test specification
o ISO/IEC 9646-7 Information technology—Open Systems Interconnection—
Conformance testing methodology and framework—Part 7: Implementation
Conformance Statements
ISO 9660 Information processing – Volume and file structure of CD-ROM for
information interchange
ISO 9712 Non-destructive testing - Qualification and certification of NDT personnel
ISO/IEC 9796 Information technology – Security techniques – Digital signature
schemes giving message recovery
Page 17
- www.snacademycenter.com – Page 17 of 33
ISO/IEC 9797 Information technology – Security techniques – Message
Authentication Codes (MACs)
o ISO/IEC 9797-1 Mechanisms using a block cipher
o ISO/IEC 9797-2 Mechanisms using a dedicated hash-function
ISO/IEC 9798 Information technology – Security techniques – Entity authentication
ISO/IEC 9834 Information technology – Open Systems Interconnection – Procedures
for the operation of OSI Registration Authorities
ISO 9869 Thermal insulation – Building elements – In-situ measurements of thermal
resistance and thermal transmittance
ISO/IEC 9899 Programming languages – C
ISO/IEC/IEEE 9945 Information technology – Portable Operating System Interface
(POSIX®) Base Specifications, Issue 7
ISO 9984 Information and documentation – Transliteration of Georgian characters
into Latin characters
ISO 9985 Information and documentation – Transliteration of Armenian characters
into Latin characters
ISO 9992 Financial transaction cards – Messages between the integrated circuit card
and the card accepting device
ISO/IEC 9995 Information technology – Keyboard layouts for text and office systems
ISO 9999 Assistive products for persons with disability – Classification and
terminology
ISO 10000 – ISO 10999 ISO 10001:2007 Quality management – Customer satisfaction – Guidelines for codes
of conduct for organizations
ISO 10002:2014 Quality management – Customer satisfaction – Guidelines for
complaints handling in organizations
ISO 10003:2007 Quality management – Customer satisfaction – Guidelines for
dispute resolution external to organizations
ISO 10004:2008 Quality management – Customer satisfaction – Guidelines for
monitoring and measuring
ISO 10005:2005 Quality management systems – Guidelines for quality plans
ISO 10006:2003 Quality management systems – Guidelines for quality management
in projects
ISO 10007:2003 Quality management systems – Guidelines for configuration
management
ISO 10012:2003 Measurement management systems – Requirements for
measurement processes and measuring equipment
ISO/TR 10013:2001 Guidelines for quality management system documentation
ISO 10014:2006 Quality management – Guidelines for realizing financial and
economic benefits
ISO 10015:1999 Quality management – Guidelines for training
ISO/TR 10017:2003 Guidance on statistical techniques for ISO 9001:2000
ISO 10018:2012 Quality management – Guidelines on people involvement and
competence
ISO 10019:2005 Guidelines for the selection of quality management system
consultants and use of their services
ISO/IEC 10021 Information technology – Message Handling Systems (MHS)
ISO/IEC 10026 Information technology – Open Systems Interconnection
ISO 10077 Thermal performance of windows, doors and shutters – Calculation of
thermal transmittance
Page 18
- www.snacademycenter.com – Page 18 of 33
ISO/IEC 10089 Information technology – 130 mm rewritable optical disk cartridge
for information interchange
ISO/IEC 10116 Information technology – Security techniques – Modes of operation
for an n-bit block cipher
ISO/IEC 10118 Information technology – Security techniques – Hash-functions
ISO 10160 Information and documentation – Open Systems Interconnection –
Interlibrary Loan Application Service Definition
ISO 10161 Information and documentation – Open Systems Interconnection –
Interlibrary Loan Application Protocol Specification
ISO/IEC 10164 Information technology – Open Systems Interconnection – Systems
Management
ISO/IEC 10179:1996 Information technology – Processing languages – Document
Style Semantics and Specification Language (DSSSL)
ISO/IEC 10206 Information technology – Programming languages – Extended Pascal
ISO 10211 Thermal bridges in building construction – Heat flows and surface
temperatures – Detailed calculations
ISO 10218 Robots and robotic devices – Safety requirements for industrial robots
ISO/IEC 10279 Information technology – Programming languages – Full BASIC
ISO 10303 Industrial automation systems and integration – Product data
representation and exchange
ISO 10380 Pipework — Corrugated metal hoses and hose assemblies
ISO 10383 Securities and related financial instruments – Codes for exchanges and
market identification (MIC)
ISO 10456 Building materials and products – Hygrothermal properties – Tabulated
design values and procedures for determining declared and design thermal values
ISO 10487 Passenger cars – Connections for car radios[Note 3]
ISO 10555 Sterile, single-use intravascular catheters
ISO 10579 Geometrical product specifications (GPS) – Dimensioning and tolerancing
– Non-rigid parts
ISO 10628 Flow diagrams for process plants
ISO/IEC 10646 Information technology – Universal Coded Character Set (UCS)
ISO 10664 Hexalobular internal driving feature for bolts and screws – Torx screw
head
ISO 10668 Brand valuation -- Requirements for monetary brand valuation
ISO/IEC 10746 Information technology - Open distributed processing
o ISO/IEC 10746-1 Information technology - Open Distributed Processing -
Reference model: Overview
o ISO/IEC 10746-2 Information technology - Open distributed processing -
Reference model: Foundations
o ISO/IEC 10746-3 Information technology - Open distributed processing -
Reference model: Architecture
o ISO/IEC 10746-4 Information technology - Open Distributed Processing -
Reference Model: Architectural semantics
ISO 10816 Mechanical vibration
o ISO 10816-1:1995 Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts—Part 1: General guidelines
o ISO 10816-2:2009 Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts—Part 2: Land-based steam turbines and
generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1
800 r/min, 3 000 r/min and 3 600 r/min
Page 19
- www.snacademycenter.com – Page 19 of 33
o ISO 10816-3:2009 Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts—Part 3: Industrial machines with
nominal power above 15 kW and nominal speeds between 120 r/min and 15
000 r/min when measured in situ
o ISO 10816-4:2009 Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts—Part 4: Gas turbine sets with fluid-film
bearings
o ISO 10816-5:2000 Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts—Part 5: Machine sets in hydraulic power
generating and pumping plants
o ISO 10816-6:1995 Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts—Part 6: Reciprocating machines with
power ratings above 100 kW
o ISO 10816-7:2009 Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts—Part 7: Rotodynamic pumps for
industrial applications, including measurements on rotating shafts
o ISO 10816-8:2014 Mechanical vibration - Evaluation of machine vibration by
measurements on non-rotating parts—Part 8: Reciprocating compressor
systems
ISO 10957 Information and documentation – International standard music number
(ISMN)
ISO 10962 Securities and related financial instruments – Classification of Financial
Instruments (CFI code)
ISO 10993 Biological evaluation of medical devices
ISO 11000 – ISO 11999 ISO 11064 Ergonomic design of control centres
o ISO 11064-1:2000 Principles for the design of control centres
o ISO 11064-2:2000 Principles for the arrangement of control suites
o ISO 11064-3:1999 Control room layout ISO 11064-3:1999/Cor 1:2002
o ISO 11064-4:2004 Layout and dimensions of workstations
o ISO 11064-5:2008 Displays and controls
o ISO 11064-6:2005 Environmental requirements for control centres
o ISO 11064-7:2006 Principles for the evaluation of control centres
ISO 11120 Gas cylinders—Refillable seamless steel tubes for compressed gas
transport, of water capacity between 150 l and 3000 l -- Design construction and
testing
ISO 11135:2014 Sterilization of health-care products—Ethylene oxide—
Requirements for the development, validation and routine control of a sterilization
process for medical devices
ISO 11137 Sterilization of health care products – Radiation
ISO 11170:2003 Hydraulic fluid power – Filter elements – Sequence of tests for
verifying performance characteristics
ISO 11171:2010 Hydraulic fluid power – Calibration of automatic particle counters
for liquids
ISO/IEC 11172 Information technology – Coding of moving pictures and associated
audio for digital storage media at up to about 1,5 Mbit/s
ISO/IEC 11179 Information technology – Metadata registries (MDR)
ISO 11357 Plastics – Differential scanning calorimetry (DSC)
o ISO 11357-1:2009 General principles
Page 20
- www.snacademycenter.com – Page 20 of 33
o ISO 11357-2:2013 Determination of glass transition temperature and glass
transition step height
o ISO 11357-3:2011 Determination of temperature and enthalpy of melting and
crystallization
o ISO 11357-4:2005 Determination of specific heat capacity
o ISO 11357-5:2013 Determination of characteristic reaction-curve temperatures
and times, enthalpy of reaction and degree of conversion
o ISO 11357-6:2008 Determination of oxidation induction time (isothermal
OIT) and oxidation induction temperature (dynamic OIT)
o ISO 11357-7:2002 Determination of crystallization kinetics
ISO/IEC 11404 Information technology – General-Purpose Datatypes (GPD)
ISO 11446:2004 Road vehicles – Connectors for the electrical connection of towing
and towed vehicles – 13-pole connectors for vehicles with 12 V nominal supply
voltage
ISO 11469:2000 Plastics – Generic identification and marking of plastics products
ISO/IEC 11578:1996 Information technology – Open Systems Interconnection –
Remote procedure call (RPC)
ISO 11783 Tractors and machinery for agriculture and forestry – Serial control and
communications data network
ISO/IEC 11801 Information technology – Generic cabling for customer premises
ISO 11898 Road vehicles – Controller area network (CAN)
ISO 12000 – ISO 12999 ISO 12006 Building construction – Organization of information about construction
works
ISO/IEC 12207 Systems and software engineering – Software life cycle processes
ISO 12100 Safety of machinery – General principles for design – Risk assessment and
risk reduction
ISO 12639 Graphic technology – Prepress digital data exchange – Tag image file
format for image technology (TIFF/IT)
ISO 12641 Graphic technology – Prepress digital data exchange – Colour targets for
input scanner calibration
ISO/TS 12805:2011 Nanotechnologies – Materials specifications – Guidance on
specifying nano-objects
ISO 12859/TR Intelligent transport systems – System architecture – Privacy aspects
in ITS standards and systems
ISO 12944 Paints and varnishes – Corrosion protection of steel structures by
protective paint systems
ISO 13000 – ISO 13999 ISO 13007 Ceramic tiles – Grouts and adhesives
o ISO 13007-1:2014 Terms, definitions and specifications for adhesives
o ISO 13007-2:2010 Test methods for adhesives
o ISO 13007-3:2010 Terms, definitions and specifications for grouts
o ISO 13007-4:2013 Test methods for grouts
ISO/TR 13121:2011 Nanotechnologies – Nanomaterial risk evaluation
ISO 13239 Information technology – Telecommunications and information exchange
between systems – High-level data link control (HDLC) procedures
ISO/IEC 13249 Information technology – Database languages – SQL multimedia and
application
ISO/IEC 13250 Information technology – Topic Maps[Note 3]
Page 21
- www.snacademycenter.com – Page 21 of 33
ISO 13320:2009 Particle size analysis - Laser diffraction methods
ISO/IEC 13346 Information technology – Volume and file structure of write-once and
rewritable media using non-sequential recording for information interchange
ISO 13370 Thermal performance of buildings – Heat transfer via the ground –
Calculation methods
ISO 13406-2:2001 Ergonomic requirements for work with visual displays based on
flat panels – Part 2: Ergonomic requirements for flat panel displays [withdrawn 2008-
11-14]
ISO 13450 Photography – 110-size cartridge, film and backing paper – Dimensions
ISO 13482:2014 Robots and robotic devices – Safety requirements for personal care
robots
ISO 13485:2003 Medical devices – Quality management systems – Requirements for
regulatory purposes
ISO/IEC 13490 Information technology – Volume and file structure of read-only and
write-once compact disk media for information interchange
ISO 13567 Technical product documentation – Organization and naming of layers for
CAD
ISO/IEC 13568:2002 Information Technology – Z formal specification notation –
Syntax, type system and semantics
ISO 13577 Industrial furnaces and associated processing equipment - Safety
o ISO 13577-1 General requirements
ISO 13579 Industrial furnaces and associated processing equipment - Method of
measuring energy balance and calculating efficiency
o ISO 13579-1 General methodology
o ISO 13579-2 Reheating furnaces for steel
o ISO 13579-3 Batch-type aluminium melting furnaces
o ISO 13579-4 Furnaces with protective or reactive atmosphere
ISO 13586:2000 Plastics - Determination of fracture toughness (GIC and KIC) --
Linear elastic fracture mechanics (LEFM) approach
ISO 13616 Financial services – International bank account number (IBAN)
ISO 13628 Petroleum and natural gas industries – Design and operation of subsea
production systems
o ISO 13628-1 General requirements and recommendations
o ISO 13628-2 Unbonded flexible pipe systems for subsea and marine
applications
o ISO 13628-3 Through flowline (TFL) systems
o ISO 13628-4 Subsea wellhead and tree equipment
o ISO 13628-5 Subsea umbilicals
o ISO 13628-6 Subsea production control systems
o ISO 13628-7 Completion/workover riser systems
o ISO 13628-8 Remotely Operated Vehicle (ROV) interfaces on subsea
production systems
o ISO 13628-9 Remotely Operated Tool (ROT) intervention systems
o ISO 13628-10 Specification for bonded flexible pipe
o ISO 13628-11 Flexible pipe systems for subsea and marine applications
ISO 13715 Technical drawings—Edges of undefined shape—Vocabulary and
indications
ISO 13849 Safety of machinery – Safety related parts of control systems
ISO/IEC 13818 Information technology – Generic coding of moving pictures and
associated audio information
Page 22
- www.snacademycenter.com – Page 22 of 33
ISO 13837 Road vehicles – Safety glazing materials – Method for the determination
of solar transmittance
ISO 14000 – ISO 14999 ISO 14000 Environmental management systems [This is a set of standards, rather than
a single standard.]
ISO 14001 Environmental management systems – Requirements with guidance for
use
ISO 14004 Environmental management systems – General guidelines on principles,
systems and support techniques
ISO 14031 Environmental management - Environmental performance evaluation –
Guidelines
ISO 14050 Environmental management – Vocabulary
ISO 14051 Environmental management – Material flow cost accounting - General
framework
ISO 14064 Greenhouse gases
ISO 14155:2011 Clinical investigation of medical devices for human subjects – Good
clinical practice
ISO 14223 Radiofrequency [sic] identification of animals – Advanced transponders
ISO 14224 Petroleum, petrochemical and natural gas industries - Collection and
exchange of reliability and maintenance data for equipment
ISO 14230 Road vehicles – Diagnostic systems – Keyword Protocol 2000
ISO 14405-1 Geometrical product specifications (GPS) – Dimensional tolerancing –
Part 1: Linear sizes
ISO/IEC 14443 Identification cards – Contactless integrated circuit cards – Proximity
cards
ISO/IEC 14462 - Open-EDI Reference Model
ISO/IEC 14496 Information technology – Coding of audio-visual objects
ISO 14641 Electronic archiving
o ISO 14641-1:2012 Specifications concerning the design and the operation of
an information system for electronic information preservation
ISO 14644 Cleanrooms and associated controlled environments
ISO/IEC 14651 Information technology – International string ordering and
comparison – Method for comparing character strings and description of the common
template tailorable ordering
ISO 14698 Cleanrooms and associated controlled environments – Biocontamination
control
o ISO 14698-1 General principles and methods
o ISO 14698-2 Evaluation and interpretation of biocontamination data
ISO/IEC 14750 Information technology – Open Distributed Processing – Interface
Definition Language
ISO/IEC 14755 Information technology – Input methods to enter characters from the
repertoire of ISO/IEC 10646 with a keyboard or other input device
ISO 14801 Dentistry – Implants – Dynamic fatigue test for endosseous dental
implants
ISO 14855-1 Determination of the ultimate aerobic biodegradability of plastic
materials under controlled composting conditions – Method by analysis of evolved
carbon dioxide
ISO 14855-1:2005 General method
ISO 14855-2:2007 Gravimetric measurement of carbon dioxide evolved in a
laboratory-scale test
Page 23
- www.snacademycenter.com – Page 23 of 33
ISO/IEC 14882 Programming Languages – C++
ISO 14915 Software ergonomics for multimedia user interfaces
o ISO 14915-1:2002 Design principles and framework
o ISO 14915-2:2003 Multimedia navigation and control
o ISO 14915-3:2002 Media selection and combination
ISO 14971:2007 Medical devices – Application of risk management to medical
devices
ISO/IEC 14977 Information technology – Syntactic metalanguage – Extended BNF
ISO 15000 – ISO 15999 ISO/TS 15000 Electronic business eXtensible Markup Language ebXML
ISO 15022 Securities – Scheme for messages (Data Field Dictionary)
ISO 15082 Road vehicles – Tests for rigid plastic safety glazing materials
ISO 15099 Thermal performance of windows, doors and shading devices – Detailed
calculations
ISO 15112 Natural gas – Energy determination
ISO 15189 Medical laboratories – Particular requirements for quality and competence
ISO 15223 Medical devices – Symbols to be used with medical device labels,
labelling, and information to be supplied
ISO/IEC 15288 Systems and software engineering – System life cycle processes
ISO/IEC 15289 Systems and software engineering – Content of systems and software
life cycle process information products (Documentation)
ISO/IEC 15291 Information technology – Programming languages – Ada Semantic
Interface Specification (ASIS)
ISO 15403 Natural gas – Natural gas for use as a compressed fuel for vehicles
o ISO 15403-1 Designation of the quality
ISO/IEC 15408 Information technology – Security techniques – Evaluation criteria
for IT security
ISO/IEC 15414 - Open data processing - Reference Model - Enterprise Language
ISO/IEC 15434 Information technology – Automatic identification and data capture
techniques – Syntax for high-capacity ADC media
ISO/IEC 15444 Information technology – JPEG 2000 image coding system
ISO/IEC 15445:2000 Information technology – Document description and processing
languages – HyperText Markup Language (HTML)
ISO 15489-1:2001 Information and documentation – Records management – Part 1:
General
ISO/TR 15489-2:2001 Information and documentation – Records management – Part
2: Guidelines
ISO/IEC 15504 Information technology – Process assessment
ISO 15614 Specification and qualification of welding procedures for metallic
materials – Welding procedure test
ISO 15686 Buildings and constructed assets – Service life planning
ISO/IEC 15693 Identification cards – Contactless integrated circuit cards – Vicinity
cards
ISO 15706 Information and documentation – International Standard Audiovisual
Number (ISAN)
ISO 15707 Information and documentation – International Standard Musical Work
Code (ISWC)
ISO 15783:2002 Seal-less rotodynamic pumps – Class II – Specification
ISO 15836 Information and documentation – The Dublin Core metadata element set
Page 24
- www.snacademycenter.com – Page 24 of 33
ISO/IEC 15897 Information technology – Procedures for registration of cultural
elements
ISO 15924 Information and documentation – Codes for the representation of names of
scripts
ISO 15926 - Integration of Life-cycle Data for Process Plants including Oil and Gas
Production Facilities
ISO 15930 Graphic technology – Prepress digital data exchange using PDF[Note 3]
ISO/IEC 15944 - Business Agreement Semantic Descriptive Techniques
ISO/IEC 15948 Information technology – Computer graphics and image processing –
Portable Network Graphics (PNG): Functional specification
ISO 15970 Natural gas – Measurement of properties – Volumetric properties: density,
pressure, temperature and compression factor
ISO 15971:2008 Natural gas – Measurement of properties – Calorific value and
Wobbe index
ISO 15985:2004 Plastics – Determination of the ultimate anaerobic biodegradation
and disintegration under high-solids anaerobic-digestion conditions – Method by
analysis of released biogas
ISO 16000 – ISO 16999 ISO 16134 Earthquake- and subsidence-resistant design of ductile iron pipelines
ISO 16232 Road vehicles – Cleanliness of components of fluid circuits
o ISO 16232-8 Particle nature determination by microscopic analysis
o ISO 16232-9 Particle sizing and counting by automatic light extinction particle
counter
o ISO 16232-10 Expression of results
ISO/IEC 16262 Information technology – Programming languages, their
environments and system software interfaces – ECMAScript language specification
ISO/IEC 16500 Information technology – Generic digital audio-visual systems
ISO 16549 Textiles – Unevenness of textile strands – Capacitance method
ISO 16610 Geometrical product specifications (GPS) – Filtration
ISO 16750 Road vehicles – Environmental conditions and testing for electrical and
electronic equipment
ISO 16792 Technical product documentation - Digital product definition data
practices
ISO/TS 16949 Quality management systems – Particular requirements for the
application of ISO 9001:2008 for automotive production and relevant service part
organizations
ISO/TR 16982:2002 Ergonomics of human-system interaction – Usability methods
supporting human-centred design
ISO 17000 – ISO 17999 ISO/IEC 17020:2012 Conformity assessment—Requirements for the operation of
various types of bodies performing inspection
ISO/IEC 17021:2011 Conformity assessment—Requirements for bodies providing
audit and certification of management systems
o ISO/IEC TS 17021-2:2012 Conformity assessment—Requirements for bodies
providing audit and certification of management systems—Part 2:
Competence requirements for auditing and certification of environmental
management systems
o ISO/IEC TS 17021-3:2013 Conformity assessment—Requirements for bodies
providing audit and certification of management systems—Part 3:
Page 25
- www.snacademycenter.com – Page 25 of 33
Competence requirements for auditing and certification of quality
management systems
o ISO/IEC TS 17021-4:2013 Conformity assessment—Requirements for bodies
providing audit and certification of management systems—Part 4:
Competence requirements for auditing and certification of event sustainability
management systems
o ISO/IEC TS 17021-5:2014 Conformity assessment—Requirements for bodies
providing audit and certification of management systems—Part 5:
Competence requirements for auditing and certification of asset management
systems
ISO/IEC TS 17022:2012 Conformity assessment—Requirements and
recommendations for content of a third-party audit report on management systems
ISO/IEC TS 17023:2013 Conformity assessment—Guidelines for determining the
duration of management system certification audits
ISO/IEC 17024:2003 Conformity assessment – General requirements for bodies
operating certification of persons
ISO/IEC 17025:2005 General requirements for the competence of testing and
calibration laboratories
ISO/IEC 17050:2004 Conformity assessment — Supplier's declaration of conformity
( Part 1 - General requirements + Part 2 - Supporting documentation )
ISO/IEC 17065:2012 Conformity assessment—Requirements for bodies certifying
products, processes and services
ISO 17088:2012 Specifications for compostable plastics
ISO 17100:2015 Translation services—Requirements for translation services
ISO 17202 Textiles – Determination of twist in single spun yarns – Untwist/retwist
method
ISO/PAS 17506 Industrial automation systems and integration – COLLADA digital
asset schema specification for 3D visualization of industrial data
ISO 17776 Petroleum and natural gas industries – Offshore production installations –
Guidelines on tools and techniques for hazard identification and risk assessment
ISO 17799 - Code of Practice for Information Security Management (superseded by
ISO/IEC 27002)
ISO 17894 Ships and marine technology – Computer applications – General
principles for the development and use of programmable electronic systems in marine
applications
ISO 18000 – ISO 18999 ISO/IEC 18000 Information technology – Radio frequency identification for item
management
o ISO/IEC 18000-1 Reference architecture and definition of parameters to be
standardized
o ISO/IEC 18000-2 Parameters for air interface communications below 135 kHz
o ISO/IEC 18000-3 Parameters for air interface communications at 13,56 MHz
o ISO/IEC 18000-4 Parameters for air interface communications at 2,45 GHz
o ISO/IEC 18000-6 Parameters for air interface communications at 860 MHz to
960 MHz
o ISO/IEC 18000-7 Parameters for active air interface communications at
433 MHz
ISO/IEC 18004 Information technology – Automatic identification and data capture
techniques – QR Code 2005 bar code symbology specification
Page 26
- www.snacademycenter.com – Page 26 of 33
ISO/IEC 18009 Information technology – Programming languages – Ada: Conformity
assessment of a language processor
ISO/IEC 18013 Information technology – Personal identification – ISO-compliant
driving license
o ISO/IEC 18013-1:2005 Physical characteristics and basic data set
o ISO/IEC 18013-2:2008 Machine-readable technologies
o ISO/IEC 18013-3:2009 Access control, authentication and integrity validation
ISO/IEC 18014 Information technology – Security techniques – Time-stamping
services
ISO/IEC 18023 Information technology – SEDRIS
ISO/IEC 18024-4:2006 Information technology – SEDRIS language bindings – Part
4: C
ISO/IEC 18025:2005 Information technology – Environmental Data Coding
Specification (EDCS)
ISO/IEC 18026 Information technology – Spatial Reference Model (SRM)
ISO/IEC 18033 Information technology – Security techniques – Encryption
algorithms
o ISO/IEC 18033-1 General
o ISO/IEC 18033-2 Asymmetric ciphers
o ISO/IEC 18033-3 Block ciphers
o ISO/IEC 18033-4 Stream ciphers
ISO/IEC 18041-4 Information technology – Computer graphics, image processing and
environmental data representation – Environmental Data Coding Specification
(EDCS) language bindings – Part 4: C
ISO/IEC 18042-4:2006 Information technology – Computer graphics and image
processing – Spatial Reference Model (SRM) language bindings – Part 4: C
ISO/IEC 18092 Information technology – Telecommunications and information
exchange between systems – Near Field Communication – Interface and Protocol
(NFCIP-1)
ISO 18117:2009 Surface chemical analysis – Handling of specimens prior to analysis
ISO 18118:2004 Surface chemical analysis - Auger electron spectroscopy and X-ray
photoelectron spectroscopy - Guide to the use of experimentally determined relative
sensitivity factors for the quantitative analysis of homogeneous materials
ISO/TS 18152 Ergonomics of human-system interaction – Specification for the
process assessment of human-system issues
ISO 18185 Freight containers – Electronic seals
ISO 18245 Retail financial services – Merchant category codes
ISO/TR 18529:2000 Ergonomics – Ergonomics of human-system interaction –
Human-centred lifecycle process descriptions
ISO 18541 Road vehicles – Standardized access to automotive repair and
maintenance information (RMI)
ISO 18601:2013 Packaging and the environment - General requirements for the use of
ISO standards in the field of packaging and the environment
ISO 18602 Packaging and the environment—Optimization of the packaging system
ISO 18603 Packaging and the environment—Reuse
ISO 18604 Packaging and the environment—Material recycling
ISO 18605 Packaging and the environment—Energy recovery
ISO 18606 Packaging and the environment—Organic recycling
ISO 18629 Industrial automation systems and integration – Process specification
language
Page 27
- www.snacademycenter.com – Page 27 of 33
ISO 19000 – ISO 19999 ISO 19005 Document management – Electronic document file format for long-term
preservation
ISO 19011:2011 Guidelines for auditing management systems
ISO 19092 Financial services – Biometrics – Security framework
ISO 19101 Geographic information – Reference model
ISO/TS 19103 Geographic information – Conceptual schema language
ISO/TS 19104 Geographic information – Terminology
ISO 19105 Geographic information – Conformance and testing
ISO 19106 Geographic information – Profiles
ISO 19107 Geographic information – Spatial schema
ISO 19108 Geographic information – Temporal schema
ISO 19109 Geographic information – Rules for application schema
ISO 19110 Geographic information – Methodology for feature cataloguing
ISO 19111 Geographic information – Spatial referencing by coordinates
ISO 19112 Geographic information – Spatial referencing by geographic identifiers
ISO 19113 Geographic information – Quality principles
ISO 19114 Geographic information – Quality evaluation procedures
ISO 19115 Geographic information – Metadata
ISO 19116 Geographic information – Positioning services
ISO 19117 Geographic information – Portrayal
ISO 19118 Geographic information – Encoding
ISO 19119 Geographic information – Services
ISO/TR 19120 Geographic information – Functional standards
ISO/TR 19121 Geographic information – Imagery and gridded data
ISO/TR 19122 Geographic information / Geomatics – Qualification and certification
of personnel
ISO 19123 Geographic information – Schema for coverage geometry and functions
ISO 19125 Geographic information – Simple feature access
ISO 19126 Geographic information – Feature concept dictionaries and registers
ISO/TS 19127 Geographic information – Geodetic codes and parameters
ISO 19128 Geographic information – Web map server interface
ISO/TS 19129 Geographic information – Imagery, gridded and coverage data
framework
ISO/TS 19130 Geographic information – Imagery sensor models for geopositioning
ISO 19131 Geographic information – Data product specifications
ISO 19132 Geographic information – Location-based services – Reference model
ISO 19133 Geographic information – Location-based services – Tracking and
navigation
ISO 19134 Geographic information – Location-based services – Multimodal routing
and navigation
ISO 19135 Geographic information – Procedures for item registration
ISO 19136 Geographic information – Geography Markup Language (GML)
ISO 19137 Geographic information – Core profile of the spatial schema
ISO/TS 19138 Geographic information – Data quality measures
ISO/TS 19139 Geographic information – Metadata – XML schema implementation
ISO 19141 Geographic information – Schema for moving features
ISO 19142 Geographic information – Web Feature Service
ISO 19143 Geographic information – Filter encoding
ISO 19144 Geographic information – Classification systems
Page 28
- www.snacademycenter.com – Page 28 of 33
ISO 19146 Geographic information – Cross-domain vocabularies
ISO 19156 Geographic information - Observations and measurements
ISO 19439 Enterprise integration – Framework for enterprise modelling
ISO 19440 Enterprise integration – Constructs for enterprise modelling
ISO/IEC 19501 Information technology – Open Distributed Processing – Unified
Modeling Language (UML) Version 1.4.2
ISO/IEC 19502 Information technology – Meta Object Facility (MOF)
ISO/IEC 19503 Information technology – XML Metadata Interchange (XMI)
ISO 19600 Compliance management systems -- Guidelines
ISO/IEC 19752 Information technology – Method for the determination of toner
cartridge yield for monochromatic electrophotographic printers and multi-function
devices that contain printer components
ISO/IEC 19757 Information technology – Document Schema Definition Languages
(DSDL)
o ISO/IEC 19757-2 Regular-grammar-based validation – RELAX NG
o ISO/IEC 19757-3 Rule-based validation – Schematron
o ISO/IEC 19757-4 Namespace-based Validation Dispatching Language
(NVDL)
ISO/IEC 19770 Information technology – Software asset management
ISO/IEC 19785 Information technology – Common Biometric Exchange Formats
Framework
ISO/IEC 19788 Information technology – Learning, education and training –
Metadata for learning resources
ISO/IEC 19790 Information technology – Security techniques – Security
requirements for cryptographic modules
ISO/IEC 19793 - Open Distributed Processing—Use of UML for ODP system
specifications
ISO/IEC 19794 Information technology – Biometric data interchange formats
o ISO/IEC 19794-1:2011 Framework
o ISO/IEC 19794-2:2005 Finger minutiae data
o ISO/IEC 19794-3:2006 Finger pattern spectral data
o ISO/IEC 19794-4:2005 Finger image data
o ISO/IEC 19794-5:2005 Face image data
o ISO/IEC 19794-6:2005 Iris image data
o ISO/IEC 19794-7:2007 Signature/sign time series data
o ISO/IEC 19794-8:2006 Finger pattern skeletal data
o ISO/IEC 19794-9:2007 Vascular image data
o ISO/IEC 19794-10:2007 Hand geometry silhouette data
ISO 19993 Timber structures—Glued laminated timber—Face and edge joint
cleavage test
ISO 20000 – ISO 20999 ISO/IEC 20000 Information technology – Service management
ISO 20022 Financial services – UNIversal Financial Industry message scheme
ISO 20072 Aerosol drug delivery device design verification—Requirements and test
methods
ISO 20252 Market, opinion and social research — Vocabulary and service
requirements
ISO/TS 20282 Usability of consumer products and products for public use
ISO 20400 Sustainable procurement -- Guidance
Page 29
- www.snacademycenter.com – Page 29 of 33
ISO 20653 Road vehicles - Degrees of protection (IP-Code) - Protection of electrical
equipment against foreign objects, water and access
ISO 20700 Guidelines for management consultancy services
ISO 20815 Petroleum, petrochemical and natural gas industries - Production
assurance and reliability management
ISO/IEC TR 20943 Information technology – Procedures for achieving metadata
registry content consistency
o ISO/IEC TR 20943-1:2003 Data elements
o ISO/IEC TR 20943-3:2004 Value domains
ISO 21000 – ISO 21999 ISO/IEC 21000 Information technology – Multimedia framework (MPEG-21)
ISO/IEC 21481 Information technology – Telecommunications and information
exchange between systems – Near Field Communication Interface and Protocol -2
(NFCIP-2)
ISO 21482 Ionizing-radiation warning – Supplementary symbol
ISO 21500 Guidance on project management
ISO 22000 – ISO 22999 ISO 22000:2005 Food safety management systems – Requirements for any
organization in the food chain
ISO/TS 22002 Prerequisite programmes on food safety
o ISO/TS 22002-1:2009 Prerequisite programmes on food safety – Part 1: Food
manufacturing
o ISO/TS 22002-2:2013 Prerequisite programmes on food safety – Part 2:
Catering
o ISO/TS 22002-3:2011 Prerequisite programmes on food safety – Part 3:
Farming
o ISO/TS 22002-4:2013 Prerequisite programmes on food safety - Part 4: Food
packaging manufacturing
o ISO/TS 22002-6:2016 Prerequisite programmes on food safety - Part 6: Feed
and animal food production
ISO/TS 22003:2013 Food safety management systems – Requirements for bodies
providing audit and certification of food safety management systems
ISO 22004:2014 Food safety management systems – Guidance on the application of
ISO 22000
ISO 22005:2007 Traceability in the feed and food chain – General principles and
basic requirements for system design and implementation
ISO 22006:2009 Quality management systems - Guidelines for the application of ISO
9001:2008 to crop production)
ISO 22093 Industrial automation systems and integration – Physical device control –
Dimensional Measuring Interface Standard (DMIS)
ISO 22222 Personal financial planning -- Requirements for personal financial
planners
ISO 22241 Diesel engines – NOx reduction agent AUS 32
o ISO 22241-1 Quality requirements
o ISO 22241-2 Test methods
o ISO 22241-3 Handling, transportation and storing
ISO/IEC TR 22250 Information technology – Document description and processing
languages – Regular Language Description for XML (RELAX)
o ISO/IEC TR 22250-1:2002 RELAX Core
Page 30
- www.snacademycenter.com – Page 30 of 33
ISO 22301:2012 Societal security – Business continuity management systems –
Requirements
ISO/PAS 22399:2007 Societal security – Guideline for incident preparedness and
operational continuity management
ISO 22716:2007 Cosmetics – Good Manufacturing Practices (GMP) – Guidelines on
Good Manufacturing Practices
ISO 23000 – ISO 23999 ISO/IEC 23001 – Information technology – MPEG systems technologies
o ISO/IEC 23001-1:2006 – Part 1: Binary MPEG format for XML
o ISO/IEC 23001-2:2008 – Part 2: Fragment request units
o ISO/IEC 23001-3:2008 – Part 3: XML IPMP messages
o ISO/IEC 23001-4:2014 – Part 4: Codec configuration representation
o ISO/IEC 23001-5:2008 – Part 5: Bitstream Syntax Description Language
(BSDL)
o ISO/IEC 23001-7:2015 – Part 7: Common encryption in ISO base media file
format files
o ISO/IEC 23001-8:2013 – Part 8: Coding-independent code points
o ISO/IEC 23001-9:2014 – Part 9: Common encryption of MPEG-2 transport
streams
ISO/IEC 23002 Information technology – MPEG video technologies
ISO/IEC 23003 Information technology – MPEG audio technologies
o ISO/IEC 23003-1 MPEG Surround
o ISO/IEC 23003-2 Spatial Audio Object Coding (SAOC)
ISO/IEC 23270 Information technology – Programming languages – C#
ISO/IEC 23271 Information technology – Common Language Infrastructure (CLI)
ISO/IEC 23360 Linux Standard Base (LSB) core specification 3.1
o ISO/IEC 23360-1 Generic specification
o ISO/IEC 23360-2 Specification for IA32 architecture
o ISO/IEC 23360-3 Specification for IA64 architecture
o ISO/IEC 23360-4 Specification for AMD64 architecture
o ISO/IEC 23360-5 Specification for PPC32 architecture
o ISO/IEC 23360-6 Specification for PPC64 architecture
o ISO/IEC 23360-7 Specification for S390 architecture
o ISO/IEC 23360-8 Specification for S390X architecture
ISO 23733 Textiles – Chenille yarns – Test method for the determination of linear
density
ISO 23950 Information and documentation – Information retrieval (Z39.50) –
Application service definition and protocol specification
ISO 24000 – ISO 24999 ISO/IEC 24707:2007 Information technology – Common Logic (CL): a framework
for a family of logic-based languages
ISO/IEC 24727 Identification cards – Integrated circuit card programming interfaces
o ISO/IEC 24727-1 Architecture
o ISO/IEC 24727-2 Generic card interface
o ISO/IEC 24727-3 Application interface
o ISO/IEC 24727-4 Application programming interface (API) administration
o ISO/IEC 24727-5 Testing procedures
o ISO/IEC 24727-6 Registration authority procedures for the authentication
protocols for interoperability
Page 31
- www.snacademycenter.com – Page 31 of 33
ISO/IEC 24744:2014 Software Engineering – Metamodel for Development
Methodologies
ISO/IEC TR 24748:2010 Systems and software engineering - Life cycle management
ISO/IEC 24762:2008 Information technology – Security techniques – Guidelines for
information and communications technology disaster recovery services
ISO 25000 – ISO 25999 ISO 25178 Geometrical product specifications (GPS) – Surface texture: Areal
ISO 26000 – ISO 26999 ISO 26000 Guidance on social responsibility
ISO/IEC 26300 Information technology – Open Document Format for Office
Applications (OpenDocument) v1.0
ISO 27000 – ISO 27999 ISO/IEC 27000 Information technology – Security techniques – Information security
management systems – Overview and vocabulary
ISO/IEC 27001 Information technology – Security techniques – Information security
management systems – Requirements
ISO/IEC 27002 Information technology – Security techniques – Code of practice for
information security management
ISO/IEC 27003 Information technology – Security techniques – Information security
management system implementation guidance
ISO/IEC 27004 Information technology – Security techniques – Information security
management – Measurement
ISO/IEC 27005 Information technology – Security techniques – Information security
risk management
ISO/IEC 27006 Information technology – Security techniques – Requirements for
bodies providing audit and certification of information security management systems
ISO/IEC 27011 Information technology – Security techniques – Information security
management guidelines for telecommunications organizations based on ISO/IEC
27002
ISO/IEC 27037:2012 Information technology – Security techniques – Guidelines for
identification, collection, acquisition and preservation of digital evidence
ISO/TS 27687:2008 Nanotechnologies – Terminology and definitions for nano-
objects – Nanoparticle, nanofibre and nanoplate
ISO 27799:2008 Health informatics—Information security management in health
using ISO/IEC 27002
ISO 28000 – ISO 28999 ISO 28000 Specification for security management systems for the supply chain
ISO 28001:2007 Security management systems for the supply chain – Best practices
for implementing supply chain security, assessments and plans – Requirements and
guidance
ISO 28003 Security management systems for the supply chain – Requirements for
bodies providing audit and certification of supply chain security management systems
ISO 28004 Security management systems for the supply chain – Guidelines for the
implementation of ISO 28000
ISO/PAS 28007:2012 Ships and marine technology—Guidelines for Private Maritime
Security Companies (PMSC) providing privately contracted armed security personnel
(PCASP) on board ships (and pro forma contract)
Page 32
- www.snacademycenter.com – Page 32 of 33
ISO 28300:2008 Petroleum, petrochemical and natural gas industries – Venting of
atmospheric and low-pressure storage tanks
ISO 29000 – ISO 29999 ISO/IEC 29119 Software and systems engineering – Software testing
ISO/IEC 29500 Information technology – Document description and processing
languages – Office Open XML File Formats
o ISO/IEC 29500-1 Fundamentals and Markup Language Reference
o ISO/IEC 29500-2 Open Packaging Conventions
o ISO/IEC 29500-3 Markup Compatibility and Extensibility
o ISO/IEC 29500-4 Transitional Migration Features
ISO 30000 – ISO 39999 ISO 30000:2009 Ships and marine technology – Ship recycling management systems
– Specifications for management systems for safe and environmentally sound ship
recycling facilities
ISO/IEC 30170:2012 Information technology – Programming languages – Ruby
ISO 31000:2009 Risk management – Principles and guidelines
ISO/IEC 31010:2009 Risk management - Risk assessment techniques
ISO 32000 Document management – Portable document format
ISO 37001 Anti-bribery management systems
ISO 37120 Sustainable development of communities - Indicators for city services and
quality of life
ISO/IEC 38500:2008 Corporate governance of information technology
ISO 40000 – ISO 49999 ISO/IEC 40500:2012 Information technology – W3C Web Content Accessibility
Guidelines (WCAG) 2.0
ISO/IEC 42010:2011 Systems and software engineering – Architecture description
ISO 44001:2017 Collaborative business relationship management systems —
Requirements and framework
ISO 50000 - ISO 59999 ISO 50001:2011 Energy management systems – Requirements with guidance for use
ISO 50002:2014 Energy audits – Requirements with guidance for use
ISO 50003:2014 Energy management systems – Requirements for bodies providing
audit and certification of energy management systems
ISO 50004:2014 Energy management systems – Guidance for the implementation,
maintenance and improvement of an energy management system
ISO 50006:2014 Energy management systems – Measuring energy performance using
energy baselines (EnB) and energy performance indicators (EnPI) – General
principles and guidance
ISO 50015:2014 Energy management systems – Measurement and verification of
energy performance of organizations—General principles and guidance
ISO 50047:2016 Energy savings – Determination of energy savings in organizations
ISO 55000:2014 Asset management – Overview, principles and terminology
ISO 55001:2014 Asset management – Management systems – Requirements
ISO 55002:2014 Asset management – Management systems – Guidelines for the
application of ISO 55001
ISO 80000 - ISO 89999 ISO/IEC 80000 Quantities and units
ISO/TS 80004 Nanotechnologies – Vocabulary
Page 33
- www.snacademycenter.com – Page 33 of 33
o ISO/TS 80004-1 Core terms
o ISO/TS 80004-3 Carbon nano-objects
o ISO/TS 80004-4 Nanostructured materials
o ISO/TS 80004-5 Nano/bio interface
o ISO/TS 80004-7 Diagnostics and therapeutics for healthcare
ISO 90000 - ISO 99999 ISO/IEC 90003 Software engineering -- Guidelines for the application of ISO
9001:2008 to computer software
